Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Accounting”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
NASA NTRS1996

SEADYN Analysis of a Tow Line for a High Altitude Towed Glider

The concept of using a system, consisting of a tow aircraft, glider and tow line, which would enable subsonic flight at altitudes above 24 km (78 kft) has previously been investigated. The preliminary results from these studies seem encouraging. Under certain conditions these studies indicate the concept is feasible. However, the previous studies did not accurately take into account the forces acting on the tow line. Therefore in order to investigate the concept further a more detailed analysis was needed. The code that was selected was the SEADYN cable dynamics computer program which was developed at the Naval Facilities Engineering Service Center. The program is a finite element based structural analysis code that was developed over a period of 10 years. The results have been validated by the Navy in both laboratory and at actual sea conditions. This code was used to simulate arbitrarily-configured cable structures subjected to excitations encountered in real-world operations. The Navy's interest was mainly for modeling underwater tow lines, however the code is also usable for tow lines in air when the change in fluid properties is taken into account. For underwater applications the fluid properties are basically constant over the length of the tow line. For the tow aircraft/glider application the change in fluid properties is considerable along the length of the tow line. Therefore the code had to be modified in order to take into account the variation in atmospheric properties that would be encountered in this application. This modification consisted of adding a variable density to the fluid based on the altitude of the node being calculated. This change in the way the code handled the fluid density had no effect on the method of calculation or any other factor related to the codes validation.

Colozza, Anthony J.↗
NASA NTRS1997

Analytical, Experimental, and Modelling Studies of Lunar and Terrestrial Rocks

The goal of our research has been to understand the paths and the processes of planetary evolution that produced planetary surface materials as we find them. Most of our work has been on lunar materials and processes. We have done studies that obtain geological knowledge from detailed examination of regolith materials and we have reported implications for future sample-collecting and on-surface robotic sensing missions. Our approach has been to study a suite of materials that we have chosen in order to answer specific geologic questions. We continue this work under NAG5-4172. The foundation of our work has been the study of materials with precise chemical and petrographic analyses, emphasizing analysis for trace chemical elements. We have used quantitative models as tests to account for the chemical compositions and mineralogical properties of the materials in terms of regolith processes and igneous processes. We have done experiments as needed to provide values for geochemical parameters used in the models. Our models take explicitly into account the physical as well as the chemical processes that produced or modified the materials. Our approach to planetary geoscience owes much to our experience in terrestrial geoscience, where samples can be collected in field context and sampling sites revisited if necessary. Through studies of terrestrial analog materials, we have tested our ideas about the origins of lunar materials. We have been mainly concerned with the materials of the lunar highland regolith, their properties, their modes of origin, their provenance, and how to extrapolate from their characteristics to learn about the origin and evolution of the Moon's early igneous crust. From this work a modified model for the Moon's structure and evolution is emerging, one of globally asymmetric differentiation of the crust and mantle to produce a crust consisting mainly of ferroan and magnesian igneous rocks containing on average 70-80% plagioclase, with a large, mafic, trace-element-rich geochemical province, and a regolith that globally contains trace-element-rich material distributed from this province by the Imbrium basin-forming impact. This contrasts with earlier models of a concentrically zoned Moon with a crust of ferroan anorthosite overlying a layer of urKREEP overlying ultramafic cumulates. From this work, we have learned lessons useful for developing strategies for studying regolith materials that help to maximize the information available about both the evolution of the regolith and the igneous differentiation of the planet. We believe these lessons are useful in developing strategies for on-surface geological, mineralogical, and geochemical studies, as well. The main results of our work are given in the following brief summaries of major tasks. Detailed accounts of these results have been submitted in the annual progress reports.

Haskin, Larry A.↗
NASA NTRS1996

Southern Hemisphere In Situ Observations of OH, HO2, CIO and BrO from the ER-2 Aircraft for the 1994 ASHOE Mission

A summary of the first order scientific conclusions that emerged from the research done under this grant are as follows: (1) For the first time, the concentration of the key hydrogen and halogen radicals OH, H02, ClO and BrO were determined on a global scale extending from the arctic circle to the antarctic circle, over the altitude domain of the ER-2. That domain extends from 15-20 km altitude, covering a critical part of the lower stratosphere; (2) Simultaneous, in situ measurements of the concentrations of OH, H02, ClO, BrO, NO and NO2 demonstrate the predominance of odd-hydrogen and halogen free radical catalysis in determining the rate of removal of ozone in the lower stratosphere over the complete ASHOE mission. This extends to the global scale the "first look" data obtained during the NASA Stratospheric Photochemistry and Dynamics Experiment (SPADE), executed out of Ames Research Center in June 1993. This represents a major rearrangement of our understanding with respect to the hierarchy of dominant catalytic cycles controlling ozone loss in the lower stratosphere. For the past twenty years, it has been assumed that nitrogen radicals dominate the destruction rate of ozone in the lower stratosphere; (3) Throughout the altitude and latitude range covered by ASHOE, it was determined that a single catalytic cycle, HO2 + O3 yields OH + 2O2, accounted for one half of the total O3 removal in this region of the atmosphere. Halogen radical catalytic cycles were found to account for one third of the ozone loss, and nitrogen radicals were found to account for 20% of the loss; (4) Simultaneous observations of the full complement of radicals, tracers, ozone, and water vapor during ASHOE demonstrated quantitatively the coupling that exists between the rate limiting radicals and other reactive species in the photochemical reaction network. Specifically, the concentrations of ClO and HO2 are inversely correlated with the concentration of NOx. This carries the implication that the NOx effluent from the proposed High Speed Civil Transport may be less destructive to stratospheric ozone than had previously been thought. ASHOE brought this conclusion forward for the first time on a global basis; and (5) The density of BrO was measured on a global scale during ASHOE in the lower stratosphere. It was found that bromine is responsible for 55-65% of the local rate of catalytic destruction of ozone by reactions involving bromine and chlorine. Normalizing calculated loss rates to total available inorganic bromine and chlorine explicitly demonstrates that bromine is 60-80 times more efficient than chlorine in removing ozone in the lower stratosphere. An inferred value of total inorganic bromine is in excellent agreement with measurements of their source species, organic bromine compounds in the troposphere.

Anderson, James G.↗
NASA NTRS1997

The historical contribution of solid rocket motors to the one centimeter debris population

The measured small particle population in earth orbit contains cm-sized objects that are not accounted for by breakup fragments. It was proposed that slag ejection during solid rocket motor burn is a contributor to this population. The direct evidence for such slag ejection follows from: observations of the exhausts of vehicles in flight, and engineering data from static firings. A source model is presented to account for the contribution of slag expulsion from solid rocket motors to the debris population. The mass and velocity distribution of the slag effluents are taken into account and used as a source term in the debris environment model. The model is based on the available observation data and on models for slag development and ejection.

Jackson, Albert↗
NASA NTRS1998

Modeling of a Two-Phase Jet Pump with Phase Change, Shocks and Temperature-Dependent Properties

One of the primary motivations behind this work is the attempt to understand the physics of a two-phase jet pump which constitutes part of a flow boiling test facility at NASA-Marshall. The flow boiling apparatus is intended to provide data necessary to design highly efficient two-phase thermal control systems for aerospace applications. The facility will also be capable of testing alternative refrigerants and evaluate their performance using various heat exchangers with enhanced surfaces. The test facility is also intended for use in evaluating single-phase performance of systems currently using CFC refrigerants. Literature dealing with jet pumps is abundant and covers a very wide array of application areas. Example application areas include vacuum pumps which are used in the food industry, power station work, and the chemical industry; ejector systems which have applications in the aircraft industry as cabin ventilators and for purposes of jet thrust augmentation; jet pumps which are used in the oil industry for oil well pumping; and steam-jet ejector refrigeration, to just name a few. Examples of work relevant to this investigation includes those of Fairuzov and Bredikhin (1995). While past researchers have been able to model the two-phase flow jet pump using the one-dimensional assumption with no shock waves and no phase change, there is no research known to the author apart from that of Anand (1992) who was able to account for condensation shocks. Thus, one of the objectives of this work is to model the dynamics of fluid interaction between a two-phase primary fluid and a subcooled liquid secondary fluid which is being injected employing atomizing spray injectors. The model developed accounts for phase transformations due to expansion, compression, and mixing. It also accounts for shock waves developing in the different parts of the jet pump as well as temperature and pressure dependencies of the fluid properties for both the primary two-phase mixture and the secondary subcooled liquid. The research effort on which this document partly reports described a relatively simple model capable of describing the performance of a two-phase flow jet pump. The model is based on the isentropic homogeneous expansion/compression hypothesis and is capable of fully incorporating the effects of shocks in both the mixing chamber and the throat/diffuser parts of the pump. The physical system chosen is identical to that experimentally tested by Fairuzov and Bredikhin (1995) and should therefore be relatively easy to validate.

Sherif, S. A.↗
NASA NTRS1997

Cirrus Cloud Radiative and Microphysical Properties from Ground Observations and In Situ Measurements During FIRE 1991 and Their Application to Exhibit Problems in Cirrus Solar Radiative Transfer Modeling

Measurements from the FIRE 1991 cirrus cloud field experiment in the central United States are presented and analyzed. The first part focuses on cirrus microphysical properties. Aircraft 2D-probe in situ data at different cloud altitudes were evaluated for cirrus cases on four different days. Also presented are simultaneous data samples from balloonborne videosondes. Only these balloonsondes could detect the smaller crystals. Their data suggest (at least for midlatitude altitudes below 10 km) that ice crystals smaller than 15 microns in size are rare and that small ice crystals not detected by 2D-probe measurements are radiatively of minor importance, as overlooked 2D-probe crystals account for about 10% of the total extinction. The second part focuses on the link between cirrus cloud properties and radiation. With cloud macrophysical properties from surface remote sensing added to the microphysical data and additional radiation measurements at the surface, testbeds for radiative transfer models were created. To focus on scattering processes, model evaluations were limited to the solar radiative transfer by comparing calculated and measured transmissions of sunlight at the surface. Comparisons under cloud-free conditions already reveal a model bias of about +45 W/sq m for the hemispheric solar downward broadband flux. This discrepancy, which is (at least in part) difficult to explain, has to be accounted for in comparisons involving clouds. Comparisons under cirrus cloud conditions identify as the major obstacle in cirrus solar radiative transfer modeling the inability of one-dimensional radiative transfer models to account for horizontal inhomogeneities. The successful incorporation of multidimensional radiative transfer effects will depend not only on better models but critically on the ability to measure and to define characteristic inhomogeneity scales of cloud fields. The relative minor error related to the microphysical treatment is in part a reflection of the improved understanding on solar scattering on ice crystals over the last decade and of the available wealth on ice-crystal size and shape data for this study. In absence of this information, uncertainties from microphysical cirrus model assumptions will remain high.

Kinne, Stefan↗
NASA NTRS1999

Mantle Q at Period 12.4 Hours: New Estimates from Satellite Tracking and Altimetry

The most convincing estimates of mantle Q at periods of many hours have historically come from extrapolating seismic and free-oscillation estimates via some assumed frequency dependence, sometimes contrained by estimates from the Chandler Wobble. At the semidiurnal tidal period, direct estimates of Q have been difficult to obtain because of the dominating signals of the ocean tides, which account for more than 95!k of the tidal energy dissipation. But knowledge of the ocean tides has been rapidly improving, primarily owing to satellite altimetry, and in 1996 we reported (NATURE, 381, 595-7) an estimate of solid-earth tidal energy dissipation and mantle Q based on combining satellite altimeter measurements with tracking observations of tidally induced satellite orbit perturbations. Tidal estimates from both reveal a small systematic difference in the quadrature component of the degree-2, order-2 spherical harmonic coefficients, which we attribute to a small lag in the earth's body tide. The formalism accounts for this lag in both the altimeter and tracking solutions and also accounts for a very small contribution from the lunar atmospheric tide. Since this original report, both altimeter and tracking estimates have improved. Recent solutions for the body-tide lag at the M2 period are 0.20 +/- 0.09 degrees, implying an energy dissipation of 100 +/- 50 gigawatts and a solid-earth Q of 300. Further new solutions will be discussed, as will the prospects for significantly reducing error bars and for obtaining estimates from other tides in the diurnal band.

Ray, Richard D.↗
NASA NTRS1999

NCV Flow Diagnostic Test Results

There were two objectives for this test. First, was to assess the reasons why there is approximately 1.5 drag counts (cts) discrepancy between measured and computed drag improvement of the Non-linear Cruise Validation (NCV) over the Technology Concept Airplane (TCA) wing body (WB) configurations. The Navier-Stokes (N-S) pre-test predictions from Boeing Commercial Airplane Group (BCAG) show 4.5 drag cts of improvement for NCV over TCA at a lift coefficient (CL) of 0. I at Mach 2.4. The pre-test predictions from Boeing Phantom Works - Long Beach, BPW-LB, show 3.75 drag cts of improvement. BCAG used OVERFLOW and BPW-LB used CFL3D. The first test entry to validate the improvement was held at the NASA Langley Research Center (LARC) UPV;T, test number 1687. The experimental results showed that the drag improvement was only 2.6 cts, not accounting for laminar run and trip drag. This is approximately 1.5 cts less than predicted computationally. In addition to the low Reynolds Number (RN) test, there was a high RN test in the Boeing Supersonic Wind Tunnel (BSWT) of NCV and TCA. BSV@T test 647 showed that the drag improvement of NCV over TCA was also 2.6 cts, but this did account for laminar run and trip drag. Every effort needed to be done to assess if the improvement measured in LaRC UPWT and BSWT was correct. The second objective, once the first objective was met, was to assess the performance increment of NCV over TCA accounting for the associated laminar run and trip drag corrections in LaRC UPWT. We know that the configurations tested have laminar flow on portions of the wing and have trip drag due to the mechanisms used to force the flow to go from laminar to turbulent aft of the transition location.

Cappuccio, Mina↗
NASA NTRS2000

Comparison of Predicted and Measured Turbine Vane Rough Surface Heat Transfer

The proposed paper compares predicted turbine vane heat transfer for a rough surface over a wide range of test conditions with experimental data. Predictions were made for the entire vane surface. However, measurements were made only over the suction surface of the vane, and the leading edge region of the pressure surface. Comparisons are shown for a wide range of test conditions. Inlet pressures varied between 3 and 15 psia, and exit Mach numbers ranged between 0.3 and 0.9. Thus, while a single roughened vane was used for the tests, the effective rougness,(k(sup +)), varied by more than a factor of ten. Results were obtained for freestream turbulence levels of 1 and 10%. Heat transfer predictions were obtained using the Navier-Stokes computer code RVCQ3D. Two turbulence models, suitable for rough surface analysis, are incorporated in this code. The Cebeci-Chang roughness model is part of the algebraic turbulence model. The k-omega turbulence model accounts for the effect of roughness in the application of the boundary condition. Roughness causes turbulent flow over the vane surface. Even after accounting for transition, surface roughness significantly increased heat transfer compared to a smooth surface. The k-omega results agreed better with the data than the Cebeci-Chang model. However, the low Reynolds number k-omega model did not accurately account for roughness when the freestream turbulence level was low. The high Reynolds number version of this model was more suitable when the freestream turbulence was low.

Boyle, R. J.↗
NASA NTRS1996

Decision Making In A High-Tech World: Automation Bias and Countermeasures

Automated decision aids and decision support systems have become essential tools in many high-tech environments. In aviation, for example, flight management systems computers not only fly the aircraft, but also calculate fuel efficient paths, detect and diagnose system malfunctions and abnormalities, and recommend or carry out decisions. Air Traffic Controllers will soon be utilizing decision support tools to help them predict and detect potential conflicts and to generate clearances. Other fields as disparate as nuclear power plants and medical diagnostics are similarly becoming more and more automated. Ideally, the combination of human decision maker and automated decision aid should result in a high-performing team, maximizing the advantages of additional cognitive and observational power in the decision-making process. In reality, however, the presence of these aids often short-circuits the way that even very experienced decision makers have traditionally handled tasks and made decisions, and introduces opportunities for new decision heuristics and biases. Results of recent research investigating the use of automated aids have indicated the presence of automation bias, that is, errors made when decision makers rely on automated cues as a heuristic replacement for vigilant information seeking and processing. Automation commission errors, i.e., errors made when decision makers inappropriately follow an automated directive, or automation omission errors, i.e., errors made when humans fail to take action or notice a problem because an automated aid fails to inform them, can result from this tendency. Evidence of the tendency to make automation-related omission and commission errors has been found in pilot self reports, in studies using pilots in flight simulations, and in non-flight decision making contexts with student samples. Considerable research has found that increasing social accountability can successfully ameliorate a broad array of cognitive biases and resultant errors. To what extent these effects generalize to performance situations is not yet empirically established. The two studies to be presented represent concurrent efforts, with student and professional pilot samples, to determine the effects of accountability pressures on automation bias and on the verification of the accurate functioning of automated aids. Students (Experiment 1) and commercial pilots (Experiment 2) performed simulated flight tasks using automated aids. In both studies, participants who perceived themselves as accountable for their strategies of interaction with the automation were significantly more likely to verify its correctness, and committed significantly fewer automation-related errors than those who did not report this perception.

Mosier, Kathleen L.↗
NASA NTRS2002

Modeling Grade IV Gas Emboli using a Limited Failure Population Model with Random Effects

Venous gas emboli (VGE) (gas bubbles in venous blood) are associated with an increased risk of decompression sickness (DCS) in hypobaric environments. A high grade of VGE can be a precursor to serious DCS. In this paper, we model time to Grade IV VGE considering a subset of individuals assumed to be immune from experiencing VGE. Our data contain monitoring test results from subjects undergoing up to 13 denitrogenation test procedures prior to exposure to a hypobaric environment. The onset time of Grade IV VGE is recorded as contained within certain time intervals. We fit a parametric (lognormal) mixture survival model to the interval-and right-censored data to account for the possibility of a subset of "cured" individuals who are immune to the event. Our model contains random subject effects to account for correlations between repeated measurements on a single individual. Model assessments and cross-validation indicate that this limited failure population mixture model is an improvement over a model that does not account for the potential of a fraction of cured individuals. We also evaluated some alternative mixture models. Predictions from the best fitted mixture model indicate that the actual process is reasonably approximated by a limited failure population model.

Thompson, Laura A.↗
NASA NTRS2002

Effects of Hypergravity Rearing on Growth Hormone (GH) Secretion In Preweanling Rats

We previously reported that rat pups reared at 1.5-g, 1.75 or 2.0-g hypergravity weigh 6-15% less than 1.0-g controls. To account for these findings. we measured the lactational hormones, prolaction (Prl) and oxytocin (OT), in the pups' mothers. Gravity related differences in Prl were not observed whereas OT of lactating dams was significantly reduced relative to controls. Milk transfer from dam to pup was not impaired in hypergravity-reared litters tested at 1-g. Together, these findings suggest that impaired lactation and milk transfer do not account for reduced body masses of postnatal rats reared in hypergravity. In the present study, we analyzed growth hormone (GH) secretion and maternal licking in pups reared in hypergravity and in 1.0-g controls. Recent reports using dwarfing phenotypes in mouse mutants have provided evidence for postnatal dependence on GH and insulin-like growth factors (IGFs). Beginning on Gestational day (G)11 of the rats' 22 day pregnancy, rat dams and their litters were exposed to either 1.5-g, 1.75-g or 2.0-g. On Postnatal day (P)10, we measured plasma GH using enzyme immunoassay (EIA). Contrary to our hypothesis, GH was significantly elevated in pups reared at 2.0-g relative to 1.0-g controls. Pup-oriented behaviors of the hypergravity dams were also changed, possibly accounting for the increase in pup GH. GH alone does not appear to play a role in reduced body weights of hypergravity-reared pups.

Baer, L. A.↗
NASA NTRS2004

Approximate Solution for Choked Flow in Gas Seal Pads

Previous analyses of high pressure seals have considered adiabatic flow with friction but neglected effects of seal rotation. Most of this work analyzed a one-dimensional flow field. This works well to calculate stiffness and leakage of full circular seals, either face seals or annular ring seals. However, it cannot provide accurate results for a rectangular seal pad with its strongly two-dimensional flow field and its reliance on hydrodynamic forces to maintain a full fluid film. On the other hand, solutions of Reynolds lubrication equation have been obtained for the two-dimensional flow in a seal pad. But these solutions do not account for choking which occurs at high seal pressure ratios, nor do they consider the pressure loss that occurs in the entrance region of the flow field. The aim of the present work is to build on the Reynolds equation solution by use of an approximate choked flow analysis. This will account for the pressure losses in the flow entrance region, ensure that fluid velocities remain subsonic, and enable fluid inertial effects within the pad film to be accounted for. Results show that, in general, fluid inertia acts to decrease pad film load capacity and leakage, and increase film stiffness.

Fleming, David P.↗
NASA NTRS2004

Combined In-Plane and Through-the-Thickness Analysis for Failure Prediction of Bolted Composite Joints

Although two-dimensional methods provide accurate predictions of contact stresses and bolt load distribution in bolted composite joints with multiple bolts, they fail to capture the effect of thickness on the strength prediction. Typically, the plies close to the interface of laminates are expected to be the most highly loaded, due to bolt deformation, and they are usually the first to fail. This study presents an analysis method to account for the variation of stresses in the thickness direction by augmenting a two-dimensional analysis with a one-dimensional through the thickness analysis. The two-dimensional in-plane solution method based on the combined complex potential and variational formulation satisfies the equilibrium equations exactly, and satisfies the boundary conditions and constraints by minimizing the total potential. Under general loading conditions, this method addresses multiple bolt configurations without requiring symmetry conditions while accounting for the contact phenomenon and the interaction among the bolts explicitly. The through-the-thickness analysis is based on the model utilizing a beam on an elastic foundation. The bolt, represented as a short beam while accounting for bending and shear deformations, rests on springs, where the spring coefficients represent the resistance of the composite laminate to bolt deformation. The combined in-plane and through-the-thickness analysis produces the bolt/hole displacement in the thickness direction, as well as the stress state in each ply. The initial ply failure predicted by applying the average stress criterion is followed by a simple progressive failure. Application of the model is demonstrated by considering single- and double-lap joints of metal plates bolted to composite laminates.

Kradinov, V.↗
NASA NTRS2003

Particle Engulfment and Pushing By Solidifying Interfaces

The study of particle behavior at solid/liquid interfaces (SLI s) is at the center of the Particle Engulfment and Pushing (PEP) research program. Interactions of particles with SLI s have been of interest since the 1960 s, starting with geological observations, i.e., frost heaving. Ever since, this field of research has become significant to such diverse areas as metal matrix composite materials, fabrication of superconductors, and inclusion control in steels. The PEP research effort is geared towards understanding the fundamental physics of the interaction between particles and a planar SLI. Experimental work including 1-g and mu-g experiments accompany the development of analytical and numerical models. The experimental work comprised of substantial groundwork with aluminum (Al) and zinc (Zn) matrices containing spherical zirconia particles, mu-g experiments with metallic Al matrices and the use of transparent organic metal-analogue materials. The modeling efforts have grown from the initial steady-state analytical model to dynamic models, accounting for the initial acceleration of a particle at rest by an advancing SLI. To gain a more comprehensive understanding, numerical models were developed to account for the influence of the thermal and solutal field. Current efforts are geared towards coupling the diffusive 2-D front tracking model with a fluid flow model to account for differences in the physics of interaction between 1-g and -g environments. A significant amount of this theoretical investigation has been and is being performed by co-investigators at NASA MSFC.

Source record↗
NASA NTRS2004

Modeling the Nonlinear, Strain Rate Dependent Deformation of Shuttle Leading Edge Materials with Hydrostatic Stress Effects Included

An analysis method based on a deformation (as opposed to damage) approach has been developed to model the strain rate dependent, nonlinear deformation of woven ceramic matrix composites, such as the Reinforced Carbon Carbon (RCC) material used on the leading edges of the Space Shuttle. In the developed model, the differences in the tension and compression deformation behaviors have also been accounted for. State variable viscoplastic equations originally developed for metals have been modified to analyze the ceramic matrix composites. To account for the tension/compression asymmetry in the material, the effective stress and effective inelastic strain definitions have been modified. The equations have also been modified to account for the fact that in an orthotropic composite the in-plane shear response is independent of the stiffness in the normal directions. The developed equations have been implemented into LS-DYNA through the use of user defined subroutines (UMATs). Several sample qualitative calculations have been conducted, which demonstrate the ability of the model to qualitatively capture the features of the deformation response present in woven ceramic matrix composites.

Goldberg, Robert K.↗
NASA NTRS2000

Biological removal of gaseous ammonia in biofilters: space travel and earth-based applications

Gaseous NH3 removal was studied in laboratory-scale biofilters (14-L reactor volume) containing perlite inoculated with a nitrifying enrichment culture. These biofilters received 6 L/min of airflow with inlet NH3 concentrations of 20 or 50 ppm, and removed more than 99.99% of the NH3 for the period of operation (101, 102 days). Comparison between an active reactor and an autoclaved control indicated that NH3 removal resulted from nitrification directly, as well as from enhanced absorption resulting from acidity produced by nitrification. Spatial distribution studies (20 ppm only) after 8 days of operation showed that nearly 95% of the NH3 could be accounted for in the lower 25% of the biofilter matrix, proximate to the port of entry. Periodic analysis of the biofilter material (20 and 50 ppm) showed accumulation of the nitrification product NO3- early in the operation, but later both NO2- and NO3- accumulated. Additionally, the N-mass balance accountability dropped from near 100% early in the experiments to approximately 95 and 75% for the 20- and 50-ppm biofilters, respectively. A partial contributing factor to this drop in mass balance accountability was the production of NO and N2O, which were detected in the biofilter exhaust.

NASA Discipline Life Support Systems↗
NASA NTRS1999

Horizontal vestibuloocular reflex evoked by high-acceleration rotations in the squirrel monkey. I. Normal responses

The horizontal angular vestibuloocular reflex (VOR) evoked by high-frequency, high-acceleration rotations was studied in five squirrel monkeys with intact vestibular function. The VOR evoked by steps of acceleration in darkness (3,000 degrees /s(2) reaching a velocity of 150 degrees /s) began after a latency of 7.3 +/- 1.5 ms (mean +/- SD). Gain of the reflex during the acceleration was 14.2 +/- 5.2% greater than that measured once the plateau head velocity had been reached. A polynomial regression was used to analyze the trajectory of the responses to steps of acceleration. A better representation of the data was obtained from a polynomial that included a cubic term in contrast to an exclusively linear fit. For sinusoidal rotations of 0.5-15 Hz with a peak velocity of 20 degrees /s, the VOR gain measured 0.83 +/- 0.06 and did not vary across frequencies or animals. The phase of these responses was close to compensatory except at 15 Hz where a lag of 5.0 +/- 0.9 degrees was noted. The VOR gain did not vary with head velocity at 0.5 Hz but increased with velocity for rotations at frequencies of >/=4 Hz (0. 85 +/- 0.04 at 4 Hz, 20 degrees /s; 1.01 +/- 0.05 at 100 degrees /s, P < 0.0001). No responses to these rotations were noted in two animals that had undergone bilateral labyrinthectomy indicating that inertia of the eye had a negligible effect for these stimuli. We developed a mathematical model of VOR dynamics to account for these findings. The inputs to the reflex come from linear and nonlinear pathways. The linear pathway is responsible for the constant gain across frequencies at peak head velocity of 20 degrees /s and also for the phase lag at higher frequencies being less than that expected based on the reflex delay. The frequency- and velocity-dependent nonlinearity in VOR gain is accounted for by the dynamics of the nonlinear pathway. A transfer function that increases the gain of this pathway with frequency and a term related to the third power of head velocity are used to represent the dynamics of this pathway. This model accounts for the experimental findings and provides a method for interpreting responses to these stimuli after vestibular lesions.

NASA Program Biomedical Research and Countermeasur↗