Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “surface wetting”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

Soil moisture and evapotranspiration predictions using Skylab data

The author has identified the following significant results. Multispectral reflectance and emittance data from the Skylab workshop were evaluated for prediction of evapotranspiration and soil moisture for an irrigated region of southern Texas. Wavelengths greater than 2.1 microns were required to spectrally distinguish between wet and dry fallow surfaces. Thermal data provided a better estimate of soil moisture than did data from the reflective bands. Thermal data were dependent on soil moisture but not on the type of agricultural land use. The emittance map, when used in conjunction with existing models, did provide an estimate of evapotranspiration rates. Surveys of areas of high soil moisture can be accomplished with space altitude thermal data. Thermal data will provide a reliable input into irrigation scheduling.

Myers, V. I.↗

ATS-6 mm-wave propagation experiment

Attenuation on a Space-to-Earth path was measured at 20 GHz for a ground terminal at approximately 1 km elevation in an arid (16 cm annual precipitation) region of eastern Washington state. Precipitation intensity and radiometric sky temperature at 20 GHz were also measured. Attenuation greater than 1 dB was observed only in the presence of wet snow on antenna surfaces. Ten thousand (10,000) hours of radiometric sky temperature data recorded over an 18-month period indicated atmospheric attenuation of 5 to 7 dB during two instances of rain intensity of approximately 1 inch per hour.

Davis, C. C.↗

A comparative study of microwave radiometer observations over snowfields with radiative transfer model calculations

Truck mounted microwave instrumentation was used to study the microwave emission characteristics of the Colorado Rocky Mountain snowpack in the vicinity of Fraser, Colorado during the winter of 1978. The spectral signatures of 5.0, 10.7, 18, and 37 GHz radiometers with dual polarization were used to measure the snowpack density and temperature profiles, rain profile, and free water content. These data were compared with calculated results based on microscopic scattering models for dry, surface melting, and very wet snowpacks.

Chang, A. T. C.↗

Process modifications for improved carbon fiber composites: Alleviation of the electrical hazards problem

Attempts to alleviate carbon-fiber-composite electrical hazards during airplane crash fires through fiber gasification are described. Thermogravimetric and differential scanning calorimetric experiments found several catalysts that caused fibers to combust when composites were exposed to test fires. Composites were tested in the 'Burn-Bang' apparatus and in high voltage electrical detection grid apparatus. In a standard three minute burn test modified composites released no fibers, while state-of-the-art composites released several hundred fiber fragments. Expected service life with and without catalytic modification was studied and electron microscopy and X-ray microanalysis furnished physical appearance and chemical composition data. An acrylic acid polymer fiber coating was developed that wet the carbon fiber surface uniformly with the catalyst, providing a marked contrast with the uneven coats obtained by solution-dipping.

Ramohalli, K.↗

Evaporation from a partially wet forest canopy

The results of experimental studies of water storage in a Sitka-spruce canopy are presented and analyzed in terms of model simulations of evaporation. Wet-branch cantilever deflection was measured along with meteorological data on three days in August, 1976, to determine the relationship of canopy evaporation to wind speed and (hence) aerodynamic resistance. Two versions of a simple unilayer model of sensible and latent heat transport from a partially wet canopy were tested in the data analysis: model F1 forbids the exchange of heat between wet and dry foliage surfaces; model F2 assumes that this exchange is highly efficient. Model F1 is found to give results consistent with the rainfall-interception model of Rutter et al. (1971, 1975, 1977), but model F2 gives results which are more plausible and correspond to the multilayer simulations of Sellers and Lockwood (1981) and the experimental findings of Hancock and Crowther (1979). It is inferred that the role of eddy diffusivity for water vapor is enhanced relative to momentum transport, and that the similarity hypothesis used in conventional models may fail in the near vicinity of a forest canopy.

Hancock, N. H.↗

Research Review, 1983

The Global Modeling and Simulation Branch (GMSB) of the Laboratory for Atmospheric Sciences (GLAS) is engaged in general circulation modeling studies related to global atmospheric and oceanographic research. The research activities discussed are organized into two disciplines: Global Weather/Observing Systems and Climate/Ocean-Air Interactions. The Global Weather activities are grouped in four areas: (1) Analysis and Forecast Studies, (2) Satellite Observing Systems, (3) Analysis and Model Development, (4) Atmospheric Dynamics and Diagnostic Studies. The GLAS Analysis/Forecast/Retrieval System was applied to both FGGE and post FGGE periods. The resulting analyses have already been used in a large number of theoretical studies of atmospheric dynamics, forecast impact studies and development of new or improved algorithms for the utilization of satellite data. Ocean studies have focused on the analysis of long-term global sea surface temperature data, for use in the study of the response of the atmosphere to sea surface temperature anomalies. Climate research has concentrated on the simulation of global cloudiness, and on the sensitivities of the climate to sea surface temperature and ground wetness anomalies.

Source record↗

Organic materials for ceramic molding processes

Ceramic molding processes are examined. Binders, wetting agents, lubricants, plasticizers, surface active agents, dispersants, etc., for pressing, rubber pressing, sip casting, injection casting, taping, extrusion, etc., are described, together with forming machines.

Saito, K.↗

A V-grooved AlGaAs/GaAs passivated PN junction

A passivated, V-grooved GaAs solar cell offers important advantages in terms of improved optical coupling, higher short circuit current, and increased tolerance to particle radiation when compared to the planar cell configuration. An AlGaAs epilayer has been deposited on a p-type GaAs epilayer grown on an n-type V-grooved GaAs surface using MOCVD. A wet chemical etching process was used to produce a V-pattern with a 7.0 micron periodicity. Reflectivity measurements substantiate the expected decrease in solar reflectance. Scanning electron microscopy techniques were used to confirm the presence of the AlGaAs layer and verify the existence of a pn junction.

Bailey, Sheila G.↗

Formation of a pn junction on an anisotropically etched GaAs surface using metalorganic chemical vapor deposition

A continuous p-type GaAs epilayer has been deposited on an n-type sawtooth GaAs surface using MOCVD. A wet chemical etching process was used to expose the intersecting (111)Ga and (-1 -1 1)Ga planes with 6-micron periodicity. Charge-collection microscopy was used to verify the presence of the pn junction thus formed and to measure its depth. The ultimate goal of this work is to fabricate a V-groove GaAs cell with improved absorptivity, high short-circuit current, and tolerance to particle radiation.

Leon, R. P.↗

A V-grooved AlGaAs/GaAs passivated pn junction

A passivated, V-grooved GaAs solar cell offers important advantages in terms of improved optical coupling, higher short-circuit current, and increased tolerance to particle radiation when compared to the planar cell configuration. An AlGaAs epilayer has been deposited on a p-type GaAs epilayer grown on an n-type V-grooved GaAs surface using MOCVD. A wet chemical etching process was used to produce a V-pattern with a 7.0-micron periodicity. Reflectivity measurements substantiate the expected decrease in solar reflectance. Scanning electron microscopy techniques were used to confirm the presence of the AlGaAs layer and verify the existence of a pn junction.

Bailey, S. G.↗

Solidification Using a Baffle in Sealed Ampoules (SUBSA)

Solidification Using a Baffle in Sealed Ampoules (SUBSA) will be the first materials science experiment conducted in the Microgravity Science Glovebox (MSG) Facility at the International Space Station (ISS) Alpha. The launch is schedule for May 31, 2002. Using the specially developed furnace, 10 Te and Zn-doped single crystals of InSb will be directionally solidified in microgravity. A key goal of the SUBSA investigation is to (i) clarify the origin of the melt motion in space laboratories and (ii) to reduce the magnitude of the melt motion to the point that it does not interfere with the transport phenomena. These goals will be accomplished through a special ampoule and furnace design. A disk-shaped baffle, positioned close to the freezing front, is used to reduce melt motion. Furthermore, the solidification will be visualized by using a transparent furnace, with a video camera, continuously sending images to the earth. This allows detection of bubbles and melt de-wetting that could cause surface tension driven convection. In preparation for the space experiments, 30 ground-based experiments were conducted. The results of ground based tests and numerical modeling will be presented. Based on numerical modeling, 12 mm 1D silica ampoules were selected. The small diameter ampoule favors closer placement of the baffle to the interface, without excessive radial segregation caused by forced convection while providing more damping of natural convection. The parts in the silica ampoule include 2 carbon springs made by Energy Science Laboratories, Inc., a pyrocarbon-coated graphite cylinder, pyrocarbon-coated graphite a baffle with the shaft and the InSb charge with the seed crystal grown by W.A. Bonner of Crystallod Inc.

Marin, C.↗

Influence of Idealized Heterogeneity on Wet and Dry Planetary Boundary Layers Coupled to the Land Surface

We examine the influence of surface heterogeneity on boundary layers using a large-eddy simulation coupled to a land-surface model. Heterogeneity, imposed in strips varying from 2-30 km (1 less than lambda/z(sub i) less than 18), is found to dramatically alter the structure of the free convective boundary layer by inducing significant organized circulations. A conditional sampling technique, based on the scale of the surface heterogeneity (phase averaging), is used to identify and quantify the organized surface fluxes and motions in the atmospheric boundary layer. The impact of the organized motions on turbulent transport depends critically on the scale of the heterogeneity lambda, the boundary layer height zi and the initial moisture state of the boundary layer. Dynamical and scalar fields respond differently as the scale of the heterogeneity varies. Surface heterogeneity of scale 4 less than lamba/z(sub i) less than 9 induces the strongest organized flow fields (up, wp) while heterogeneity with smaller or larger lambda/z(sub i) induces little organized motion. However, the organized components of the scalar fields (virtual potential temperature and mixing ratio) grow continuously in magnitude and horizontal scale, as lambda/z(sub i) increases. For some cases, the organized motions can contribute nearly 100% of the total vertical moisture flux. Patch-induced fluxes are shown to dramatically impact point measurements that assume the time-average vertical velocity to be zero. The magnitude and sign of this impact depends on the location of the measurement within the region of heterogeneity.

Houser, Paul↗

Tank Tests of a 1/7-Size Powered Dynamic Model of the Grumman XJR2F-1 Amphibian: Spray Characteristics, Take-Off and Landing Stability in Smooth Water - Langley Tank Model 212, TED No. NACA 2378

Tests of a model of the XJR2F-Y amphibian were made in Langley tank no. to determine the spray characteristics and the take-off and landing stability. At a gross load of 22,000 pounds full size, spray entered the propeller disk only at a very narrow range of speeds. The spray striking the flaps was not excessive and no appreciable wetting of the tail surfaces was noted. The trim limits of stability appeared to be satisfactory and the upper-limit porpoising was not violent. The stable range of center-of-gravity locations with flaps set 20deg was well aft of the desired operating range. However, with flaps up, the forward limit was about 18 percent mean aerodynamic chord and the aft limit about 28.5 percent mean aerodynamic chord at a load of 26,000 pounds and with elevators deflected -10deg. Under these conditions the location of the step is considered satisfactory. Tests showed that the effect of water in the nose-wheel well would be to move the forward limit aft about 2-percent mean aerodynamic chord. Without ventilation of the main step, the model skipped during landing at most trims, but this skipping was not violent. With the ventilation, the model skipped lightly only at trims where the afterbody keel was approximately parallel to the water (around 7.5 deg).

Land, Norman S.↗

A Marine Origin for the Meridiani Planum Landing Site?

The Opportunity instruments have provided compelling evidence that the sulfate-rich chemical and siliciclastic sediments at the Meridiani Planum landing site were deposited in shallow water. The local paleo-environment is most often characterized as a broad, shallow sea or large playa, with surface conditions cycling between wet and dry episodes, interbedding evaporates with eolian fine sediments [e.g., 1,2]. This particular working hypothesis is reasonable, considering the area characterized by the rover s mobility. An alternative, marine origin will be considered here, a working hypothesis that we feel provides a better fit to the local-scale results identified by Opportunity, and the regional-scale characteristics of Meridiani Planum provided by data from orbiting spacecraft, when considered together.

Parker, T. J.↗

Fabrication of Single Crystal MgO Capsules

A method has been developed for machining MgO crystal blocks into forms for containing metallic and silicate liquids at temperatures up to 2,400 C, and pressures up to at least 320 kilobars. Possible custom shapes include tubes, rods, insulators, capsules, and guides. Key differences in this innovative method include drilling along the crystallographic zone axes, use of a vibration minimizing material to secure the workpiece, and constant flushing of material swarf with a cooling medium/lubricant (water). A single crystal MgO block is cut into a section .5 mm thick, 1 cm on a side, using a low-speed saw with a 0.004 blade. The cut is made parallel to the direction of cleavage. The block may be cut to any thickness to achieve the desired length of the piece. To minimize drilling vibrations, the MgO block is mounted on a piece of adhesive putty in a vise. The putty wad cradles the bottom half of the entire block. Diamond coring tools are used to drill the MgO to the desired custom shape, with water used to wet and wash the surface of swarf. Compressed air may also be used to remove swarf during breaks in drilling. The MgO workpiece must be kept cool at all times with water. After all the swarf is rinsed off, the piece is left to dry overnight. If the workpiece is still attached to the base of the MgO block after drilling, it may be cut off by using a diamond cutoff wheel on a rotary hand tool or by using a low-speed saw.

Danielson, Lisa↗

FY 2017 Center Innovation Fund Annual Report - Highlights/Abstract section

This project evaluated the feasibility of low pressure cold plasma (CP) for two applications: disinfection of produce grown in space and sterilization of medical equipment in space. Currently there is no ISS capability for disinfecting pick and eat crops, food utensils, food production areas, or medical devices. This deficit is extended to projected long duration missions. Small, portable, cold plasma devices would provide an enhanced benefit to crew health and address issues concerning microbial cross contamination. The technology would contribute to the reduction of solid waste since currently crews utilize benzalkonium chloride wet wipes for cleaning surfaces and might use PRO-SAN wipes for cleaning vegetables. CP cleaning/disinfection/sterilization can work on many surfaces, including all metals, most polymers, and this project evaluated produce. Therefore CP provides a simple system that has many different cleaning application in space: produce, medical equipment, cutlery, miscellaneous tools.

plant growt↗

Geochemical Insights Into Volcanic and Lithospheric Evolution of Mars

Introduction: The Martian lithosphere plays a pivotal role in volcanic processes, altering surface features, climate shifts, and the planet's early habitability. Crucially, the rigid lithosphere significantly influences Mars' long-term thermal conditions. Studying various geological eons’ volcanic compositions unveils how the lithosphere has evolved, even though understanding the early Noachian volcanic chemistry remains challenging due to weathering and resurfacing. In this study, newly discovered Noachian volcanic terranes[1-2] along with Hesperian and Amazonian volcanic terranes[3] are considered(Figure 1), to infer the evolution of the Martian lithosphere. Figure 1:Mars topographic map derived from MOLA-HRSC data [4] highlights the study regions including the Noachian volcanic terranes, Arabia Terra (AT), Thaumasia Minor (TM), and the Southwest Margin of Icaria Planum (SWIP)[5].Additionally, the Hesperian volcanic terranes such as Syrtis Major (SM), Hesperia Planum (HP), and, the Amazonian volcanic terranes encompass Elysium Mons (EM), Alba Patera (AP), and Olympus Mons (OM) are marked. Methods and Datasets: We use the most recent elemental mass fraction maps derived from gamma spectroscopy data from the Mars Odyssey 2001mission [6]to ascertain the bulk composition of the Martian landscape. Utilizing the updated geochemical provinces dataset of Mars[7], we consider bulk chemistry variations within our study regions. The maps, at a resolution of 50×50, encompass elements like Al, Ca, Fe, Si, K, Th, H2O, Cl, and S, detected through Gamma-Ray Spectroscopy (GRS) with decimeter scale depth sensitivity[6].Additional major and minor elements like Mg, Na, Ti, P, and Mn, using mass balance methods [8]serve as inputs for melting and crystallization simulations. We employ the pMELTS model with FMQ-3to FMQ oxygen fugacity to estimate the Pressure(P)and melting degree(F)in various eons of volcanic terranes. We have also used conventional thermobarometric calculations to determine their formation P-T conditions, using silica activity and olivine-melt Mg-exchange thermometry[9-10]. Results: Chemical Composition of Studied Volcanic Terranes: To assess formation conditions, we have investigated if GRS-measured compositions signify primary igneous processes by evaluating weathering through the Chemical Index of Alteration (CIA), K/Th ratios, and ternary plots for aqueous alteration. Consistent K/Th ratios and low CIA (<50) across volcanic regions suggest minimal large-scale weathering, affirming well-preserved igneous material extending at decimeter depths. In addition, the calculated bulk compositions align with Martian mantle equilibrium, confirming studied volcanic terranes-Arabia Terra, Thaumasia Minor, and SWIP -as primary or less altered compositions, reinforcing their representativeness at a regional GRS scale on Mars. We have also estimated the bulk compositions of Hesperian and Amazonian volcanic terranes shown in Figure 1. All volcanic terranes represent the primary or minimally altered composition. Temporal Evolution of Martian Volcanic Terranes: Our results show P-T conditions ranging from 1.3-1.6 GPa and 1350-1390°C for Noachian terranes, while Hesperian volcanic terranes vary from 1.6-1.7 GPa and 1370-1395°C, and Amazonian volcanic terranes range between 1.9-2.8 GPa and 1380-1415°C. Our analyses correspond to lithospheric thicknesses/ depth of melting for Noachian which ranges from110-135 km, 120-235 km for Hesperian terranes, and 160-235 km for Amazonian terranes. Partial melting percentages (F) range from 8-12% for Noachian, 10-11% for Hesperian, and 10-12% for Amazonian. We have also calculated mantle potential temperatures (Tp) to show variations across epochs(Figure 2). Heat flux estimation shows variations from 51-65 mW/m2 for Noachian, 38-45 mW/m2for Hesperian, and 27-39 mW/m2for Amazonian terranes, implying temporal changes in lithospheric thickness and heat flow. Comparison of Noachian volcanic terranes with Hesperian and Amazonian reveals variations in lithospheric thickness and heat flux, indicating potential implications for Martian surface conditions, including volcanic activity, climate evolution, and early habitability. Figure 2: P-T diagram displays formation conditions of studied Martian volcanic regions using GRS data, alongside Noachian-age surface basalt samples from Gusev, Gale, and Jezero. Dashed lines represent Martian mantle potential temperatures, calculated by adding the latent heat of fusion to the equilibrium temperature at which melt and solid mantle coexist and subtracting the Martian adiabatic gradient corresponding to the depth of melt. The solid line shows the Martian mantle solidus [11].Discussion& Implication: The study explores Martian volcanic activity across eons. Uniform lithospheric thickness from the Noachian to Hesperian eons suggests persistent weak plumes until Hesperian, influencing heat flow variations. Noachian's high heat flux, likely due to concentrated radioactive elements, shows spatial heterogeneity, indicating early Mars' differentiated mantle. Volcanic outgassing plays avital role in the formation of the Martian climate, likely sustained water on the surface, influencing warm-wet or cold-dry conditions. Hesperian's favorable lithospheric heat flow (45 mW/m2) supports extended water existence, resembling Earth's conditions. Whereas, Amazonian's diminished heat flux (25 mW/m2) corresponds to water loss and arid climate. Hesperian's similar lithospheric thickness to mid-Noachian implies prolonged water retention, influencing climate and potential for astrobiological research, expanding perspectives for future Martian missions. Future work: As volcanism was active throughout its history. The emergence of Mars' extensive volcanic regions, known as large igneous provinces, which are linked to intermittent volcanic activity driven by mantle plumes, poses challenges to understanding the scale and persistence of these phenomena in Martian convection models. Therefore, understanding the regional-scale changes in eruptive processes within Martian volcanic provinces over time remains unclear and crucial for deciphering the evolution of the Martian interior without Earth-like plate tectonics. We will continue this work with petrological and thermoelastic analyses to study the compositional and spatiotemporal evolution of the Elysium Volcanic Province.

A Rani↗

Thermocapillary flow with evaporation and condensation and its effect on liquid retention in low-G fluid acquisition devices

The steady motion, thermal and free surface behavior of a volatile, wetting liquid in microgravity are studied using scaling and numerical techniques. The objective is to determine whether the thermocapillary and two-phase convection arising from thermodynamic nonequilibrium along the porous surfaces of spacecraft liquid acquisition devices could cause the retention failures observed with liquid hydrogen and heated vapor pressurant. Why these devices seem immune to retention loss when pressurized with heated helium or heated directly through the porous structure was also examined. Results show that highly wetting fluids exhibit large negative and positive dynamic pressure gradients towards the meniscus interline when superheated and subcooled, respectively. With superheating, the pressure variation and recoil force arising from liquid/vapor phase change exert the same influence on surface morphology and promote retention. With subcooling, however, the pressure distribution produces a suction that degrades mechanical equilibrium of the surface. This result indicates that thermocapillary-induced deformation arising from subcooling and condensation is the likely cause for retention loss. In addition, increasing the level of nonequilibrium by reducing accommodation coefficient suppresses deformation and explains why this failure mode does not occur in instances of direct screen heating or pressurization with a heated inert gas.

Schmidt, George R.↗