Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “smoothing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Flight test results from a supercritical mission adaptive wing with smooth variable camber

The mission adaptive wing (MAW) consisted of leading- and trailing-edge variable-camber surfaces that could be deflected in flight to provide a near-ideal wing camber shape for any flight condition. These surfaces featured smooth, flexible upper surfaces and fully enclosed lower surfaces, distinguishing them from conventional flaps that have discontinuous surfaces and exposed or semiexposed mechanisms. Camber shape was controlled by either a manual or automatic flight control system. The wing and aircraft were extensively instrumented to evaluate the local flow characteristics and the total aircraft performance. This paper discusses the interrelationships between the wing pressure, buffet, boundary-layer and flight deflection measurement system analyses and describes the flight maneuvers used to obtain the data. The results are for a wing sweep of 26 deg, a Mach number of 0.85, leading and trailing-edge cambers (delta(sub LE/TE)) of 0/2 and 5/10, and angles of attack from 3.0 deg to 14.0 deg. For the well-behaved flow of the delta(sub LE/TE) = 0/2 camber, a typical cruise camber shape, the local and global data are in good agreement with respect to the flow properties of the wing. For the delta(sub LE/TE) = 5/10 camber, a maneuvering camber shape, the local and global data have similar trends and conclusions, but not the clear-cut agreement observed for cruise camber.

Powers, Sheryll Goecke↗
NASA NTRS1991

Neural nets for aligning optical components in harsh environments: Beam smoothing spatial filter as an example

The goal is to develop an approach to automating the alignment and adjustment of optical measurement, visualization, inspection, and control systems. Classical controls, expert systems, and neural networks are three approaches to automating the alignment of an optical system. Neural networks were chosen for this project and the judgements that led to this decision are presented. Neural networks were used to automate the alignment of the ubiquitous laser-beam-smoothing spatial filter. The results and future plans of the project are presented.

Decker, Arthur J.↗
NASA NTRS1992

Flight Test Results From a Supercritical Mission Adaptive Wing With Smooth Variable Camber

The mission adaptive wing (MAW) consisted of leading- and trailing-edge variable-camber surfaces that could be deflected in flight to provide a near-ideal wing camber shape for any flight condition. These surfaces featured smooth, flexible upper surfaces and fully enclosed lower surfaces, distinguishing them from conventional flaps that have discontinuous surfaces and exposed or semiexposed mechanisms. Camber shape was controlled by either a manual or automatic flight control system. The wing and aircraft were extensively instrumented to evaluate the local flow characteristics and the total aircraft performance. This paper discusses the interrelationships between the wing pressure, buffet, boundary-layer and flight deflection measurement system analyses and describes the flight maneuvers used to obtain the data. The results are for a wing sweep of 26°, a Mach number of 0.85, leading and trailing-edge cambers ( δ LE/TE ) of 0/2 and 5/10, and angles of attack from 3.0° to 14.0°. For the well-behaved flow of the δ LE/TE = 0/2 camber, a typical cruise camber shape, the local and global data are in good agreement with respect to the flow properties of the wing. For the δ LE/TE = 5/10 camber, a maneuvering camber shape, the local and global data have similar trends and conclusions, but not the clear-cut agreement observed for cruise camber.

Flight Testing↗
NASA NTRS1991

Smoothed perturbation analysis algorithms for estimating the derivatives of occupancy-related functions in serial queueing networks

The authors present smoothed perturbation analysis (SPA) estimators for the derivative of a number of occupancy-related functions in serial queuing networks with finite buffer spaces. The functions are the average number of customers at a network as seen by an arrival, the probability that a customer is blocked at a particular queue, and the probability that a customer leaves a queue empty. In all three cases, the variable is a parameter of the distribution of service times at one of the queues. The derivative estimators considered are very simple and flexible, and they easily lend themselves to analysis of unbiasedness. Unlike most of the established SPA estimators, the present ones are not based on the computation of hazard rates.

Wardi, Y.↗
NASA NTRS1992

Friction-factor data for flat-plate tests of smooth and honeycomb surfaces

Friction factors for honeycomb surfaces were measured with a flat plate tester. The flat plate test apparatus was described and a method was discussed for determining the friction factor experimentally. The friction factor model was developed for the flat plate test based on the Fanno Line Flow. The comparisons of the friction factor were plotted for smooth surfaces and six-honeycomb surfaces with three-clearances, 6.9 bar to 17.9 bar range of inlet pressures, and 5,000 to 100,000 range of the Reynolds number. The optimum geometries for the maximum friction factor were found as a function of cell width to cell depth and cell width to clearance ratios.

Ha, T. W.↗
NASA NTRS1992

Effect of uneven wall temperature on local heat transfer in a rotating square channel with smooth walls and radial outward flow

The effect of uneven wall temperature on the local heat transfer coefficient in a rotating square channel with smooth walls and radial outward flow is investigated for Reynolds numbers from 2500 to 25,000 and rotation numbers from 0 to 0.352. Three cases of thermal boundary conditions are studied: (1) four walls uniform temperature, (2) four walls uniform heat flux, and (3) leading and trailing walls hot and two side walls cold. It is shown that the heat transfer coefficients on the leading surface are much lower than that of the trailing surface due to rotation. For case 1, the leading surface heat transfer coefficient decreases and then increases with increasing rotation numbers, and the trailing surface heat transfer coefficient increases monotonically with rotation numbers. The trailing surface heat transfer coefficients, as well as those for the side walls, for case 2 are higher than for case 1, and the leading surface heat transfer coefficients for cases 2 and 3 are significantly higher than for case 1.

Han, J.-C.↗
NASA NTRS1993

Smoothed particle hydrodynamics with GRAPE-1A

We describe the implementation of a smoothed particle hydrodynamics (SPH) scheme using GRAPE-1A, a special-purpose processor used for gravitational N-body simulations. The GRAPE-1A calculates the gravitational force exerted on a particle from all other particles in a system, while simultaneously making a list of the nearest neighbors of the particle. It is found that GRAPE-1A accelerates SPH calculations by direct summation by about two orders of magnitudes for a ten thousand-particle simulation. The effective speed is 80 Mflops, which is about 30 percent of the peak speed of GRAPE-1A. Also, in order to investigate the accuracy of GRAPE-SPH, some test simulations were executed. We found that the force and position errors are smaller than those due to representing a fluid by a finite number of particles. The total energy and momentum were conserved within 0.2-0.4 percent and 2-5 x 10 exp -5, respectively, in simulations with several thousand particles. We conclude that GRAPE-SPH is quite effective and sufficiently accurate for self-gravitating hydrodynamics.

Umemura, Masayuki↗
NASA NTRS1952

Analysis of fully developed turbulent heat transfer at low Peclet numbers in smooth tubes with application to liquid metals

An analysis was made of heat transfer at low Peclet numbers for fluids flowing turbulently in smooth tubes. Previous analyses for flow of gases and liquid metals at low Peclet numbers gave higher heat-transfer coefficients than were indicated experimentally. When the mixing-length theory was modified in order to account for the heat transferred by conduction to a turbulent particle as it moves transversely, the predicted results were brought into agreement with the experimental results.

PIPES↗
NASA NTRS1951

Measurements of average heat-transfer and friction coefficients for subsonic flow of air in smooth tubes at high surface and fluid temperatures

An investigation of forced-convection heat transfer and associated pressure drops was conducted with air flowing through smooth tubes for an over-all range of surface temperature from 535 degrees to 3050 degrees r, inlet-air temperature from 535 degrees to 1500 degrees r, Reynolds number up to 500,000, exit Mach number up to 1, heat flux up to 150,000 btu per hour per square foot, length-diameter ratio from 30 to 120, and three entrance configurations. Most of the data are for heat addition to the air; a few results are included for cooling of the air. The over-all range of surface-to-air temperature ratio was from 0.46 to 3.5.

Humble, Leroy V↗
NASA NTRS1945

Flight Investigation of Boundary-layer and Profile-drag Characteristics of Smooth Wing Sections of a P-47D Airplane

In Mach range of 0.25 - 0.69, boundary-layer measurements were made on upper wing surface at 25% semi-span, pressure-distribution measurements made on upper surface at 63% semi-span, and wake surveys made at 63% semi-span. The minimum profile-drag coefficient of 0.0062 was indicated for smooth section at 63% semi-span. Critical mach number was exceeded by 0.04, but no compressibility shocks appeared. In slipstream, boundary layer transition occurred as far back as 20% chord on upper surface at low lift coefficients.

PRESSURE DISTRIBUTION - WINGS - REPUBLIC P-47D↗
NASA NTRS1944

Compressibility Effects on Heat Transfer and Pressure Drop in Smooth Cylindrical Tubes

An analysis is made to simplify pressure-drop calculations for nonadiabatic and adiabatic friction flow of air in smooth cylindrical tubes when the density changes due to heat transfer and pressure drop are appreciable. Solutions of the equation of motion are obtained by the use of Reynolds' analogy between heat transfer and skin friction. Charts of the solutions are presented for making pressure-drop calculations. A technique of using the charts to determine the position of a normal shock in a tube is described.

AIR FLOW - TUBES, CYLINDRICAL↗
NASA NTRS1951

Concerning the flow about ring-shaped cowlings Part II : annular bodies of infinite length with circulation for smooth entrance

The investigations carried out in a previous report (NACA TM 1325) concerning the flow about ring-shaped cowlings were extended by taking a circulation about the cowling into consideration. The present second report treats bodies of infinite length with approximately smooth entrance. The circulation was caused by distributing vortex rings of constant density over a stream surface extending to infinity. Furthermore, the influence of a hub body on such cowlings was dealt with. The examples treated are meant to give the designer a basis for his design.

FLOW, INCOMPRESSIBLE↗
NASA NTRS1941

Two-dimensional potential flow past a smooth wall with partly constant curvature

The speed of a two-dimensional flow potential flow past a smooth wall, which evinces a finite curvature jump at a certain point and approximates to two arcs in the surrounding area, has a vertical tangent of inflection in the critical point as a function of the arc length of the boundary curve. This report looks at a general theorem of the local character of the conformal function at the critical point as well as the case of the finite curvature jump.

Koppenfels, Werner Von↗
NASA NTRS1993

Explicit 3D continuum fracture modeling with smooth particle hydrodynamics

Impact phenomena shaped our solar system. As usual for most solar system processes, the scales are far different than we can address directly in the laboratory. Impact velocities are often much higher than we can achieve, sizes are often vastly larger, and most impacts take place in an environment where the only gravitational force is the mutual pull of the impactors. The Smooth Particle Hydrodynamics (SPH) technique has been applied in the past to the simulations of giant impacts. In these simulations, the colliding objects were so massive (at least a sizeable fraction of the Earth's mass) that material strength was negligible compared to gravity. This assumption can no longer be made when the bodies are much smaller. To this end, we have developed a 3D SPH code that includes a strength model to which we have added a von Mises yielding relation for stresses beyond the Hugoniot Elastic Limit. At the lower stresses associated with brittle failure, we use a rate-dependent strength based on the nucleation of incipient flaws whose number density is given by a Weibull distribution. Following Grady and Kipp and Melosh et al., we introduce a state variable D ('damage'), 0 less than D less than 1, which expresses the local reduction in strength due to crack growth under tensile loading. Unfortunately for the hydrodynamics, Grady and Kipp's model predicts which fragments are the most probable ones and not the ones that are really formed. This means, for example, that if a given laboratory experiment is modeled, the fragment distribution obtained from the Grady-Kipp theory would be equivalent to a ensemble average over many realizations of the experiment. On the other hand, the hydrodynamics itself is explicit and evolves not an ensemble average but very specific fragments. Hence, there is a clear incompatibility with the deterministic nature of the hydrodynamics equations and the statistical approach of the Grady-Kipp dynamical fracture model. We remedy these shortcomings by making the incipient flaw distribution explicit, i.e., particles carry activation strains which are distributed at random with a probability of occurrence given by the Weibull distribution. If the local principal axis strain exceeds this limit, damage starts to grow. By growing explicit cracks together with statistical cracks (damage) at the sub-particle scale, we ensure that material strength and fragmentation is independent of model resolution. We tested our scheme by simulating laboratory impact experiments on basalt spheres.

Benz, W.↗
NASA NTRS1993

Numerical study of a multigrid method with four smoothing methods for the incompressible Navier-Stokes equations in general coordinates

The performance of a linear multigrid method using four smoothing methods, called SCGS (Symmetrical Coupled GauBeta-Seidel), CLGS (Collective Line GauBeta-Seidel), SILU (Scalar ILU), and CILU (Collective ILU), is investigated for the incompressible Navier-Stokes equations in general coordinates, in association with Galerkin coarse grid approximation. Robustness and efficiency are measured and compared by application to test problems. The numerical results show that CILU is the most robust, SILU the least, with CLGS and SCGS in between. CLGS is the best in efficiency, SCGS and CILU follow, and SILU is the worst.

Zeng, S.↗
NASA NTRS1993

Detailed measurements in the SSME high pressure fuel turbine with smooth rotor blades

Several tests of the Rocketdyne configuration of the Space Shuttle Main Engine (SSME) High Pressure Fuel Turbopump (HPFTP) Turbine have been completed in the Turbine Test Equipment (TTE) at Marshall Space Flight Center. The tests involved using scaled performance parameters and model measurements to predict the performance of the turbine. The overall performance has been the primary objective of the tests to date, but more detailed measurements are also of interest. During the most recent test of the Rocketdyne configuration of the HPFTP turbine with smooth rotor blades, several different measurement techniques were used to study the turbine inlet and exit velocity profiles, boundary layer thicknesses, turbulence intensities, etc. Data has been obtained using various hot film probes and three-hole cobra probes. Laser Velocimeter measurements were also made. The test plan and test data will be presented and discussed as well as lessons learned on how to obtain the various types of data.

Hudson, Susan T.↗
NASA NTRS1995

Exponentially accurate approximations to piece-wise smooth periodic functions

A family of simple, periodic basis functions with 'built-in' discontinuities are introduced, and their properties are analyzed and discussed. Some of their potential usefulness is illustrated in conjunction with the Fourier series representations of functions with discontinuities. In particular, it is demonstrated how they can be used to construct a sequence of approximations which converges exponentially in the maximum norm to a piece-wise smooth function. The theory is illustrated with several examples and the results are discussed in the context of other sequences of functions which can be used to approximate discontinuous functions.

Greer, James↗