SEARCH · Engineering Papers

Results for “sensing layer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

All sources NASA NTRS DOE OSTI

NASA NTRS1996

Design and Laboratory Validation of a Capacitive Sensor for Measuring the Recession of Thin-Layered Ablator

Flight vehicles are typically instrumented with subsurface thermocouples to estimate heat transfer at the surface using inverse analysis procedures. If the vehicle has an ablating heat shield, however, temperature time histories from subsurface thermocouples no longer provide enough information to estimate heat flux at the surface. In this situation, the geometry changes and thermal energy leaves the surface in the form of ablation products. The ablation rate is required to estimate heat transfer to the surface. A new concept for a capacitive sensor has been developed to measure ablator depth using the ablator's dielectric effect on a capacitor's fringe region. Relying on the capacitor's fringe region enables the gage to be flush mounted in the vehicle's permanent structure and not intrude into the ablative heat shield applied over the gage. This sensor's design allows nonintrusive measurement of the thickness of dielectric materials, in particular, the recession rates of low-temperature ablators applied in thin (0.020 to 0.060 in. (0.05 to 0.15 mm)) layers. Twenty capacitive gages with 13 different sensing element geometries were designed, fabricated, and tested. A two-dimensional finite-element analysis was performed on several candidate geometries. Calibration procedures using ablator-simulating shims are described. A one-to-one correspondence between system output and dielectric material thickness was observed out to a thickness of 0.055 in. (1.4 mm) for a material with a permittivity about three times that of air or vacuum. A novel method of monitoring the change in sensor capacitance was developed. This technical memorandum suggests further improvements in gage design and fabrication techniques.

Gregory K Noffz↗

NASA NTRS2000

BOREAS AFM-3 NCAR Electra 1994 Aircraft Flux and Moving Window Data

The BOREAS AFM-3 team used the NCAR Electra aircraft data to make measurements of the fluxes of momentum, sensible and latent heat, carbon dioxide, and ozone over the entire BOREAS region to tie together measurements made in both the SSA and the NSA in 1994. These data were also used to study the planetary boundary layer using both in situ and remote sensing measurements. This data set contains both the aircraft flux and the moving window data. These data are stored in tabular ASCII files. The data files are available on a CD-ROM (see document number 20010000884) or from the Oak Ridge National Laboratory (ORNL) Distributed Active Archive Center (DAAC).

Lenschow, Donald H.↗

NASA NTRS2000

An all-silicon single-wafer micro-g accelerometer with a combined surface and bulk micromachining process

This paper reports an all-silicon fully symmetrical z-axis micro-g accelerometer that is fabricated on a single-silicon wafer using a combined surface and bulk fabrication process. The microaccelerometer has high device sensitivity, low noise, and low/controllable damping that are the key factors for attaining micro g and sub-micro g resolution in capacitive accelerometers. The microfabrication process produces a large proof mass by using the whole wafer thickness and a large sense capacitance by utilizing a thin sacrificial layer. The sense/feedback electrodes are formed by a deposited 2-3 microns polysilicon film with embedded 25-35 microns-thick vertical stiffeners. These electrodes, while thin, are made very stiff by the thick embedded stiffeners so that force rebalancing of the proof mass becomes possible. The polysilicon electrodes are patterned to create damping holes. The microaccelerometers are batch-fabricated, packaged, and tested successfully. A device with a 2-mm x 1-mm proof mass and a full bridge support has a measured sensitivity of 2 pF/g. The measured sensitivity of a 4-mm x 1-mm accelerometer with a cantilever support is 19.4 pF/g. The calculated noise floor of these devices at atmosphere are 0.23 micro g/sqrt(Hz) and 0.16 micro g/sqrt(Hz), respectively.

Non-NASA Center↗

NASA NTRS2010

Fiber optic gas sensor

A gas sensor includes an in-fiber resonant wavelength device provided in a fiber core at a first location. The fiber propagates a sensing light and a power light. A layer of a material is attached to the fiber at the first location. The material is able to absorb the gas at a temperature dependent gas absorption rate. The power light is used to heat the material and increases the gas absorption rate, thereby increasing sensor performance, especially at low temperatures. Further, a method is described of flash heating the gas sensor to absorb more of the gas, allowing the sensor to cool, thereby locking in the gas content of the sensor material, and taking the difference between the starting and ending resonant wavelengths as an indication of the concentration of the gas in the ambient atmosphere.

Chen, Peng↗

NASA NTRS2012

Seasonal Variability on Saturn's Moons Mimas and Tethys

We present far-ultraviolet (FUV) observations of Mimas and Tethys, which show evidence for likely seasonal variation in UV albedo across their surfaces. The ultraviolet is an important wavelength regime for studying the effects of photolytic and radiolytic processes, because primarily the uppermost layers of the regolith and grains are sensed in this range.

far-ultraviolet (FUV)↗

NASA NTRSDate not supplied

Initial analysis of “stone” size Ryugu samples: current status

As a part of the initial analysis of the Ryugu samples, we perform a variety of analyses of millimeter-sized "stones". Our goals are to elucidate the entire formation process of C-type asteroid Ryugu from the viewpoint of petrology and mineralogy ande obtain necessary information by sample analysis, and then simulate the formation of Ryugu based on the evidencef obtained rom sample analysis. Eighteen stones (8 from Room A and 10 from Room C) were received from the ISAS curation facility on June 1, 2021, and brought into a fully nitrogen-displaced glove box at Tohoku University. At the same time, we also received the powder samples from Room A and Room C. To completely block the atmosphere from leaking into the container, all samples were put in the sample transport containers prepared by ISAS, transferred from the main chamber to the glovebox at ISAS, and then all containers were completely sealed in plastic bags with moisture and oxygen absorbers. No moisture or oxygen was detected when the bags were opened in the glove box at Tohoku University, so it was confirmed that there was no exposure to the atmosphere during transport. To date, a number of analyses have been carried out successfully and almost on schedule. The analysis started with the measurement of reflectance spectra, which are sensitive to atmospheric oxidation, hydroxylation, and adsorbed water. The visible, near-infrared, and mid-infrared reflectance spectra were measured while the samples were kept airtight. The spectra of powder samples and stone samples (as aggregates and as single stone) were successfully obtained. A major feature of the stone team's analysis is the use of synchrotron radiation facilities around the world. Since this analysis is non-destructive, stone samples whose reflectance spectra were measured were sent to KEK, SPring-8, ESRF (France), SOLEIL (France), DESY (Germany), and APS (USA). Using these synchrotron radiation facilities, high spatial resolution and sensitivity XRD, STXM, XANES, CT [1], IR-CT, FT-IR [2, 3], XRF, and Mössbauer analyses were performed. Most of the analyses were carried out under air-tight conditions on the stone samples and the particulates separated from the stone samples. These analyses allowed us to determine the three-dimensional distribution of minerals and elements, redox state, density and porosity of the stone samples. Furthermore, as a characteristic analysis of the stone team, light elemental analysis using negative Muon was performed at the MLF facility of J-PARC with an exceptionally long allocation of machine time. This is the only non-destructive method to measure the concentration of light elements in the whole (not the surface) of stone samples. Because the characteristic X-rays produced by muon irradiation are much higher in energy than the fluorescent X-rays produced by X-ray irradiation, there is little effect of self-absorption by the sample, and therefore, the concentration of light elements such as carbon, oxygen, and Na in the entire "stone" sample can be determined. Some stone samples are currently being measured for heat and strength physical properties in order to understand the physical properties of asteroid Ryugu. The data obtained from these measurements are useful for interpreting the remote-sensing data data taken from the surface layer of the asteroid Ryugu [4-7]. It is also important for understanding the behavior of the Ryugu material during impact events. The surfaces of many stone samples were observed by electron microscopy and other techniques, especially on natural “flat” surfaces formed on 5 stomes. As a result, characteristric mineral aggregates formed by the reactions with water and characteiristic impact features were observed on some of the samples. Based on the observations of surfaces and the synchrotron measurements of the whole stones, important objects such as characteristic structures and specific crystal aggregates for understanding the formation history of the asteroid were identified, and these parts were separated from the stone samples using an Xe beam (pFIB) and analyzed by various methods including transmission electron microscopy and synchrotron radiation analysis. Many stone samples, from which important objects have been separated, are embedded in epoxy resin and cut to produce many polished sections. Electron microscopy and spectroscopic measurements of the polished surfaces are being carried out to reveal the detailed mineralogical properties and elemental distribution inside the stone samples. In the fall, machine time for synchrotron radiation will begin, and we plan to analyze single crystals and characteristic objects separated from the stone samples.

Tomoki Nakamura↗

NASA NTRS1994

In(X)Ga(1-X) As Strain-Layer Multiple-Quantum-Well Laser Diodes

Fabricated on InP substrates, devices operate at room temperature, emitting at wavelengths near 1.8 micrometers. By suitable modification of structure of devices, possible to achieve operation at any wavelength from 1.6 to 2.5 micrometers: this range important in lidar and in remote sensing of atmospheric gases. Quantum-well and barrier layers sandwiched between two 60-nm-thick layers of lattice-matched InGaAs. InGaAs layers sandwiched between two 150-nm-thick layers of InGaAsP. Those layers sandwiched, in turn, between InP substrate and InP cladding layer. Also layer of InGaAs atop InP cladding layers.

Forouhar, Siamak↗

DOE OSTI2025

Layer-by-layer growth of graphene oxide multilayers using robust interlayer linking chemistry. 1. Zr-bisphosphates

Graphene oxide (GO) holds substantial interest because of its utility in applications ranging from chemical sensing to catalysis and energy storage. We report on the layer-by-layer formation of graphene oxide phosphate (P-GO) multilayers on silica and oxidized silicon supports, with the layers connected via Zr-bisphosphate (ZP) linking chemistry. Layers were grown either directly by ZP linkages between P-GO sheets, or with the use of 1,4-phenylene bisphosphate (BP1) or [1,1′-biphenyl]4,4′-diyl bisphosphate (BP2). The layers have been characterized using optical null ellipsometry, X-ray photoelectron spectroscopy (XPS), UV-visible absorption spectroscopy and scanning electron microscopy (SEM). There is a linear dependence of assembly thickness on the number of layers deposited and the integrated area of the optical absorbance bands also increases linearly with number of layers deposited. XPS data provides information on interlayer linking stoichiometry. SEM images provide insight into the morphology of the adlayers, suggesting the structure and length of the interlayer linking moieties used in the multilayer assembly play a significant role in the organization of the resulting system.

Mukherjee, Neelanjana [Michigan State University, ↗

NASA NTRS1992

Fully coupled resonant-triad interaction in an adverse-pressure-gradient boundary layer

The nonlinear resonant-triad interaction, proposed by Raetz (1959), Craik (1971), and others for a Blasius boundary layer, is analyzed here for an adverse-pressure-gradient boundary layer. We assume that the adverse pressure gradient is in some sense weak and, therefore, that the instability growth rate is small. This ensures that there is a well-defined critical layer located somewhere within the flow and that the nonlinear interaction is effectively confined to that layer. The initial interaction is of the parametric resonance type, even when the modal amplitudes are all of the same order. This means that the oblique instability waves exhibit faster than exponential growth and that the growth rate of the two-dimensional mode remains linear. However, the interaction and the resulting growth rates become fully coupled, once oblique-mode amplitudes become sufficiently large, but the coupling terms are now quartic, rather than quadratic as in the Craik (1971) analysis. More importantly, however, new nonlinear interactions, which were not present in the Craik-type analyses, now come into play. These interactions eventually have a dominant effect on the instability wave development.

Goldstein, M. E.↗

NASA NTRS2001

The Estimation of Surface Latent Heat Flux over the Ocean and its Relationship to Marine Atmospheric Boundary Layer (MABL) Structure

A new technique combining active and passive remote sensing instruments for the estimation of surface latent heat flux over the ocean is presented. This synergistic method utilizes aerosol lidar backscatter data, multi-channel infrared radiometer data, and microwave scatterometer data acquired onboard the NASA P-313 research aircraft during an extended field campaign over the Atlantic ocean in support of the Lidar In-space Technology Experiment (LITE) in September of 1994. The 10 meter wind speed derived from scatterometers and lidar-radiometer inferred near-surface moisture are used to obtain an estimate of the surface flux of moisture via a bulk aerodynamic formula. The results are compared with the Special Sensor Microwave Imager (SSM/I) daily average latent heat flux and show reasonable agreement. However, the SSM/I values are biased low by about 15 W/sq m. In addition, the Marine Atmospheric Boundary Layer (MABL) height, entrainment zone thickness and integrated lidar backscatter intensity are computed from the lidar data and compared with the magnitude of the surface fluxes. The results show that the surface latent heat flux is most strongly correlated with entrainment zone depth, MABL height and the integrated MABL lidar backscatter, with corresponding correlation coefficients of 0.39, 0.43 and 0.71, respectively.

Palm, Stephen P.↗

NASA NTRS1983

The evolution of Tollmien-Schlichting waves near a leading edge

The method of matched asymptotic expansions is used to study the generation of Tollmien-Schlichting waves by free-stream disturbances incident on a flat-plate boundary layer. Near the leading edge, the motion is governed by the unsteady boundary-layer equation, while farther downstream it is governed (to lowest order) by the Orr-Sommerfeld equation with slowly varying coefficients. It is shown that there is an overlap domain where the Tollmien-Schlichting wave solutions to the Orr-Sommerfeld equation and appropriate asymptotic solutions of the unsteady boundary-layer equation match, in the matched-asymptotic-expansion sense. The analysis explains how long-wavelength free-stream disturbances can generate Tollmien-Schlichting waves of much shorter wavelength. It also leads to a set of scaling laws for the asymptotic structure of the unsteady boundary layer.

Goldstein, M. E.↗

DOE OSTI2022

Deep Learning for In-Situ Layer Quality Monitoring during Laser-Based Directed Energy Deposition (LB-DED) Additive Manufacturing Process

Defects are a leading issue for the rejection of parts manufactured through the Directed Energy Deposition (DED) Additive Manufacturing (AM) process. In an attempt to illuminate and advance in situ quality monitoring and control of workpieces, we present an innovative data-driven method that synchronously collects sensing data and AM process parameters with a low sampling rate during the DED process. The proposed data-driven technique determines the important influences that individual printing parameters and sensing features have on prediction at the inter-layer qualification to perform feature selection. Three Machine Learning (ML) algorithms including Random Forest (RF), Support Vector Machine (SVM), and Convolutional Neural Network (CNN) are used. During post-production, a threshold is applied to detect low-density occurrences such as porosity sizes and quantities from CT scans that render individual layers acceptable or unacceptable. This information is fed to the ML models for training. Training/testing are completed offline on samples deemed “high-quality” and “low-quality”, utilizing only features recorded from the build process. CNN results show that the classification of acceptable/unacceptable layers can reach between 90% accuracy while training/testing on a “high-quality” sample and dip to 65% accuracy when trained/tested on “low-quality”/“high-quality” (respectively), indicating over-fitting but showing CNN as a promising inter-layer classifier.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Boundary Layer Climatology at ARM Southern Great Plains

Operational since 1992, the Atmospheric Radiation Measurement (ARM) Southern Great Plains (SGP) site in Oklahoma, USA, has become a reference research site for meteorological studies. Because of an open data policy the ARM data are used by researchers all over the world. In this report, we review the long-term climatology of the atmospheric boundary layer, the SGP instrumentation, the site and some site-specific atmospheric conditions, which potentially affect wind turbines in the region. Because the atmospheric boundary layer is bounded and influenced by the land surface, observations of surface radiation components and heat fluxes are crucial to understanding land–atmosphere interactions. The entrainment of air, updrafts, downdrafts, and boundary layer height characteristics is needed for understanding the structure and growth of the atmospheric boundary layer. Therefore, measurements from both ground surface in situ and remote-sensing observations at the SGP site provide an overall climatology and their interactions from ground surface up to the boundary layer. Measurements from a 60 m meteorological tower, surface flux stations, disdrometers, soil temperature and moisture flux plates, coherent Doppler lidar, Raman lidar, radiosondes, and satellite data at the SGP central facility were analyzed. All the measurements were generally made within a few square kilometers of each other at the central facility. This report focuses on data from January 2010 to June 2020 at the SGP central facility. The various sections describe the ARM SGP site and surrounding wind turbines; in situ and remotesensing instrumentation used in the report; mathematical equations to analyze fluxes, turbulence, and other boundary layer parameters; a climatological analysis of surface winds, fluxes and thermodynamic parameters for several years; an analysis of observed winds in the framework of Monin-Obukhov Similarity Theory (MOST); an analysis of the boundary layer winds and direction from a Doppler lidar; multi-year turbulence estimates through the boundary layer from a Doppler lidar; atmospheric boundary layer water vapor and relative humidity profiles from Raman lidar; cloud base height and boundary layer height from multiple sensors and satellite data; and finally site-specific atmospheric conditions, such as nocturnal low-level jets.

54 ENVIRONMENTAL SCIENCES↗

NASA NTRS1994

Control of an Axisymmetric Jet Using Vortex Generators

The results of an experimental investigation on the effect of vortex generators, in the form of small tabs at the nozzle exit on the evolution of a jet, are reported in this paper. Primarily tabs of triangular shape are considered, and the effect is studied up to a jet Mach number of 1.8. Each tab is found to produce a dominant pair of counter-rotating streamwise vortices having a sense of rotation opposite to that expected from the wrapping of the boundary layer. This results in an inward indentation of the mixing layer into the core of the jet. A triangular-shaped tab with its apex leaning downstream, referred to as a delta tab, is found to be the most effective in producing such vortices, with a consequential large influence on the overall jet evolution. Two delta tabs, spaced 180 deg apart, completely bifurcate the jet. Four delta tabs stretch the mixing layer into four 'fingers,' resulting in a significant increase in the jet mixing downstream. For six delta tabs the mixing layer distortion settles back to a three finger configuration through an interaction of the streamwise vortices. The tabs are found to be equally effective in jets with turbulent or laminar initial boundary layers. Two sources of streamwise vorticity are postulated for the flow under consideration. One is the upstream 'pressure hill,' generated by the tab, which constitutes the main contributor of vorticity to the dominant pair. Another is due to vortex filaments shed from the sides of the tab and reoriented downstream by the mean shear of the mixing layer. Depending on the orientation of the tab, the latter source can produce a vortex pair having a sense of rotation opposite to that of the dominant pair. In the case of the delta tab, vorticity from the two sources add, explaining the strong effect in that configuration.

Zaman, K. B. M. Q.↗

NASA NTRS2000

Application of Radar Data to Remote Sensing and Geographical Information Systems

The field of synthetic aperture radar changed dramatically over the past decade with the operational introduction of advance radar techniques such as polarimetry and interferometry. Radar polarimetry became an operational research tool with the introduction of the NASA/JPL AIRSAR system in the early 1980's, and reached a climax with the two SIR-C/X-SAR flights on board the space shuttle Endeavour in April and October 1994. Radar interferometry received a tremendous boost when the airborne TOPSAR system was introduced in 1991 by NASA/JPL, and further when data from the European Space Agency ERS-1 radar satellite became routinely available in 1991. Several airborne interferometric SAR systems are either currently operational, or are about to be introduced. Radar interferometry is a technique that allows one to map the topography of an area automatically under all weather conditions, day or night. The real power of radar interferometry is that the images and digital elevation models are automatically geometrically resampled, and could be imported into GIS systems directly after suitable reformatting. When combined with polarimetry, a technique that uses polarization diversity to gather more information about the geophysical properties of the terrain, a very rich multi-layer data set is available to the remote sensing scientist. This talk will discuss the principles of radar interferometry and polarimetry with specific application to the automatic categorization of land cover. Examples will include images acquired with the NASA/JPL AIRSAR/TOPSAR system in Australia and elsewhere.

vanZyl, Jakob J.↗

DOE OSTI2025

Segregation of Chromium and Titanium in Sapphire Optical Fiber Grown via the Laser-Heated Pedestal Growth Technique

Our research involves growth of single crystal (SC) optical fibers to be used for sensing applications in harsh environments. Silica optical fibers are an affordable and reliable option for a wide variety of applications including optical fiber sensors and fiber lasers. However, for applications in harsh environments, such as high temperatures, radioactivity, corrosivity, etc., silica fibers are not suitable due to their instability under such conditions. Fibers composed of SC materials such as sapphire and YAG are mechanically, chemically, and thermally more robust to harsh conditions, and thus are more appropriate for sensing applications in environments such as nuclear reactors, jet engines, and boiler. However, SC fibers grown via the laser-heated pedestal growth (LHPG) technique do not intrinsically have a functional cladding layer. A cladding layer is required to reduce the modal volume for distributed sensing applications, to reduce frustrated total internal reflection induced by surface contact of the fiber in certain applications, and to improve transmissivity. Our lab investigates introduction of dopant materials during LHPG to induce an effective core-cladding structure while maintain the crystallinity of the host material. This process results in optical fiber that is not only robust to harsh environments, but also has improved optical properties for distributed sensor applications.

distributed sensing↗

DOE OSTI2025

Segregation of Chromium and Titanium in Sapphire Optical Fiber Grown via the Laser-Heated Pedestal Growth Technique

distributed sensing↗

NASA NTRS1983

Remote sensing of tropospheric gases and aerosols with airborne DIAL system

The multipurpose airborne DIAL system developed at NASA Langley Research Center is characterized, and the published results of tropospheric O3, H2O, and aerosol-backscatter remote-sensing experiments performed in 1980 and 1981 are summarized. The system comprises two tunable dye lasers pumped by frequency-doubled Nd:YAG lasers, dielectric-coated steering optics, a 36-cm-diameter Cassegrain receiver telescope, gateable photomultiplier tubes, and a minicomputer data-processing unit for real-time calculation of gas concentrations and backscattering profiles. The transmitted energy of the 100-microsec-separated dye-laser pulses is 40, 80, or 50 mJ/pulse at around 300, 600, or 720-nm wavelength, respectively. Good agreement was found between DIAL-remote-sensed and in-situ H2O and O3 profiles of the lower troposphere and O3 profiles of the tropopause region, and the usefulness of DIAL backscattering measurements in the study of boundary-layer and tropospheric dynamics is demonstrated. The feasibility of DIAL sensing of power-plant or urban plume SO2, of urban-area (or rural-area column-content) NO2, and of temperature and H2O (simultaneously using a third laser) has been suggested by simulation studies.

Browell, E. V.↗