SEARCH · Engineering Papers
Results for “scaled testing”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
NASA GRC PSL-3 Technical Challenges Full Scale Engine Test Facility Altitude and Sea Level Testing in an Ice Crystal Environment
No abstract available
Validation of High-Fidelity CFD/CAA Framework for Launch Vehicle Acoustic Environment Simulation Against Scale Model Test Data
No abstract available
Small-Scale Mechanical Testing of Space-Exposed Fluorinated Ethylene Propylene Film Obtained From the Hubble Space Telescope
No abstract available
Full-Scale Drop Test of a Fokker F28 Wingbox Fuselage Section
During the summer of 2017, a vertical drop test was conducted on a partial section of a Fokker F28 MK4000 aircraft as a part of a joint NASA/FAA effort to investigate the performance of transport category aircraft under realistic crash conditions. Ten Anthropomorphic Test Devices (ATDs, a.k.a. crash test dummies) ranging from 5th to 95th percentile sizes were used for the collection and comparison of occupant loads. Additionally, overhead bin mass simulators were added to achieve a realistic fuselage configuration. The section was dropped with a downward facing pitch angle onto a sloping soil surface in order to simulate a local horizontal velocity in the airframe. Instrumentation consisting of accelerometers was installed to measure floor, seat track, ATD, and overhead bin acceleration responses. Self-contained data recorders logging accelerations and rotational rates were also used on the seat tracks and lower structure as evaluations for crash recording devices in potential future use cases. The right side of the section was painted with a stochastic black and white speckle pattern for use in full field photogrammetric imaging techniques. Results collected from the airframe accelerometers will be presented, and deformation and failures of the test article structure will be discussed. Finally, an examination of the test article motion will be presented using derived components of local velocities with their effect on the impact acceleration and airframe response.
Low-Cost Phased Microphone Array Design for Moderate-Scale Aeroacoustics Tests
A new wall-mounted phased microphone array was designed, built, and calibrated for testing in closed or open test section wind tunnels. Two configurations were evaluated - one with microphone plate flush with the tunnel surface and the other with microphone plate recessed behind a porous screen. The arrays were successfully operated to Mach number of 0.4 and were calibrated using an in-flow speaker source during a recent study at the AEDC NFAC 40- by 80-Ft Wind Tunnel at NASA Ames.
Simulation of Lift plus Cruise Vehicle Models to Define a Full-Scale Crash Test Campaign
Explore the source record for details and available documents.
High-Repetition-Rate Flow Visualization and Velocimetry for Large-Scale Ground Test Facilities
Explore the source record for details and available documents.
An Efficient and Effective Light Gas Gun Design for Millimeter-Scale Hypervelocity Testing
This paper serves to document a design for a light gas gun that was used for 3 decades at NASA’s Langley Research Center. By adapting readily-available equipment and supplies, this apparatus was capable of accelerating projectiles at up to 9 kilometers per second. The lack of a projectile-carrying sabot sacrifices some adaptability in projectile size, but results in a design that can be cleaned and cycled with far less labor input. Overall limitation on the projectile impact energies attainable effectively limit the applications to assessing the relatively thin shields employed for robotic spacecraft (as opposed to manned missions). The original gun has been decommissioned, but it is believed that this design has application for robotic spacecraft shield testing in the modern world, allowing cost-effective generation of larger sample sizes than with conventional sabot-based light gas guns.
An Efficient and Effective Light Gas Gun Design for Millimeter-scale Hypervelocity Testing
This paper serves to document a design for a light gas gun that was used for 3 decades at NASA’s Langley Research Center. By adapting readily-available equipment and supplies, this apparatus was capable of accelerating projectiles at up to 9 kilometers per second. The lack of a projectile-carrying sabot sacrifices some adaptability in projectile size, but results in a design that can be cleaned and cycled with far less labor input. Overall limitation on the projectile impact energies attainable effectively limit the applications to assessing the relatively thin shields employed for robotic spacecraft (as opposed to manned missions). The original gun has been decommissioned, but it is believed that this design has application for robotic spacecraft shield testing in the modern world, allowing cost-effective generation of larger sample sizes than with conventional sabot-based light gas guns.
Full Scale Crash Testing at NASA Langley Research Center’s Landing and Impact Research Facility with Application Toward Electric Vertical Take off and Landing (eVTOL) Crashworthiness
Explore the source record for details and available documents.
An Efficient and Effective Light Gas Gun Design for Millimeter-Scale Hypervelocity Testing
This paper serves to document a design for a light gas gun that was used for 3 decades at NASA’s Langley Research Center. By adapting readily-available equipment and supplies, this apparatus was capable of accelerating projectiles at up to 9 kilometers per second. The lack of a projectile-carrying sabot sacrifices some adaptability in projectile size, but results in a design that can be cleaned and cycled with far less labor input. Overall limitation on the projectile impact energies attainable effectively limit the applications to assessing the relatively thin shields employed for robotic spacecraft (less useful for those used for manned missions). The original gun has been decommissioned, but it is believed that this design has application for robotic spacecraft shield testing in the modern world, allowing cost-effective generation of larger sample sizes than with conventional sabot-based light gas guns.
An Efficient and Effective Light Gas Gun Design for Millimeter-scale Hypervelocity Testing
This paper serves to document a design for a light gas gun that was used for 3 decades at NASA’s Langley Research Center. By adapting readily-available equipment and supplies, this apparatus was capable of accelerating projectiles at up to 9 kilometers per second (when new). The lack of a projectile-carrying sabot sacrifices some adaptability in projectile size, but results in a design that can be cleaned and cycled with far less labor input. Overall limitation on the projectile impact energies attainable effectively limit the applications to assessing the relatively thin shields employed for robotic spacecraft (less useful for those used for manned missions). The original gun has been decommissioned, but it is believed that this design has application for robotic spacecraft shield testing in the modern world, allowing cost-effective generation of larger sample sizes than with conventional sabot-based light gas guns.
Full-Scale Burst Testing for Inflatable Softgoods
Inflatable softgoods are complex, multi-material system in which each layer performs a specific function. NASA is supporting the private sector in development and testing of inflatable softgoods architectures through public-private partnerships. Inflatable softgoods represent one structural material option for future habitation platforms.
Mock Truss-Braced Wing Loads Calibration Research Utilizing Fiber-Optic Sensors
In support of the National Aeronautics and Space Administration Advanced Air Transonic Transport Truss-Braced Wing structural research, the Armstrong Flight Research Center Flight Loads Laboratory is performing pathfinder tests on a small, scaled test article (dubbed the mock Truss-Braced Wing) to study the application of a loads calibration on a truss-braced wing structure. The addition of a truss to the wing structure, as opposed to a purely cantilever beam setup, changes the strain-gage-based loads calibration techniques. In a truss-braced configuration, the internal shear and moments, inboard of the truss-wing connection, are not directly representative of the external aerodynamic loading as is the case for a traditional cantilever configuration. A 3-axis load cell was used at the wing-to-strut interface to estimate the load sharing between the two structural members. Crosstalk within the 3-axis load cell is added to the measurement uncertainties of the calibration effort, and the results, including crosstalk uncertainties, are presented. The calibration tests presented in this report are used as a pathfinder for developing an understanding how to perform loads calibration on a truss-braced wing structural configuration. The use of distributed fiber-optic strain sensors is leveraged to provide a near-full-span strain profile along the leading and trailing edge of the wing structure for strain-based loads calibration.
A topography‐based scaling algorithm for soil hydraulic parameters at hillslope scales: Field testing
Explore the source record for details and available documents.
Design and test of a prototype scale ejector wing
A two dimensional momentum integral analysis was used to examine the effect of changing inlet area ratio, diffuser area ratio, and the ratio of ejector length to width. A relatively wide range of these parameters was considered. It was found that for constant inlet area ratio the augmentation increases with the ejector length, and for constant length: width ratio the augmentation increases with inlet area ratio. Scale model tests were used to verify these trends and to examine th effect of aspect ratio. On the basis of these results, an ejector configuration was selected for fabrication and testing at a scale representative of an ejector wing aircraft. The test ejector was powered by a Pratt-Whitney F401 engine developing approximately 12,000 pounds of thrust. The results of preliminary tests indicate that the ejector develops a thrust augmentation ratio better than 1.65.
System-Integrated Finite Element Analysis of a Full-Scale Helicopter Crash Test with Deployable Energy Absorbers
A full-scale crash test of an MD-500 helicopter was conducted in December 2009 at NASA Langley's Landing and Impact Research facility (LandIR). The MD-500 helicopter was fitted with a composite honeycomb Deployable Energy Absorber (DEA) and tested under vertical and horizontal impact velocities of 26-ft/sec and 40-ft/sec, respectively. The objectives of the test were to evaluate the performance of the DEA concept under realistic crash conditions and to generate test data for validation of a system integrated finite element model. In preparation for the full-scale crash test, a series of sub-scale and MD-500 mass simulator tests was conducted to evaluate the impact performances of various components, including a new crush tube and the DEA blocks. Parameters defined within the system integrated finite element model were determined from these tests. The objective of this paper is to summarize the finite element models developed and analyses performed, beginning with pre-test predictions and continuing through post-test validation.