Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “primary control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS2016

Swift BAT Thermal Recovery After Loop Heat Pipe #0 Secondary Heater Controller Failure in October 2015

The Swift BAT LHP #0 primary heater controller failed on March 31, 2010. It has been disabled. On October 31, 2015, the secondary heater controller of this LHP failed. On November 1, 2015, the LHP #0 CC temperature increased to as 18.6 C, despite that the secondary heater controller set point was 8.8 C. It caused the average DM XA1 temperature to increase to 25.9 C, which was 5 C warmer than nominal. As a result, the detectors became noisy. To solve this problem, the LHP #1 secondary heater controller set point was decreased in 0.5 C decrements to 2.2 C. The set-point decrease restored the average DM XA1 temperature to a nominal value of 19.7 C on November 21.

thermal recovery in orbit↗
NASA NTRS2015

Methods for LEO Testing of CubeSat Propulsion Systems

Low Earth Orbit is becoming an inexpensive and readily available technology demonstration environment. Many new CubeSat technologies are taking advantage of this as an economical mechanism to advance beyond TRL 5. A wave of CubeSat propulsion systems favoring both reaction control and primary thrust will approach TRL 5 over the coming years, with some already there. These propulsion systems cover a wide range of capabilities including taking CubeSats to interplanetary destinations. In order to determine the feasibility of using LEO to validate the propulsion system performance and in doing so raising the TRL, a variety of factors need to be addressed. These factors include: method of measurement, environmental disturbances, spacecraft control states, and spacecraft mass properties. Propulsion Pathfinder is a NASA Ames Research Center lead project focused on raising the TRL of multiple propulsion systems over a series of flights in the coming years. This paper will highlight a few of the methods of measurement considered by this project to validate the performance of a propulsion system. The measurement methods range from tracking acceleration andor wheel spin-up to monitoring Two Line Elements between thrusting and non thrusting states. Focus will then be placed on the uncertainty of the measurement method and subsequently its feasibility through an analysis of LEO disturbance environment models and common CubeSat mass properties. In addition, the primary spacecraft control states and their imposition from the propulsion system are assessed.

Feasibility↗
NASA NTRS2006

Wavefront Sensing and Control Architecture for the Spherical Primary Optical Telescope (SPOT)

Testbed results are presented demonstrating high-speed image-based wavefront sensing and control for a spherical primary optical telescope (SPOT). The testbed incorporates a phase retrieval camera coupled to a 3-Mirror Vertex testbed (3MV) at the NASA Goddard Space Flight Center. Actuator calibration based on the Hough transform is discussed as well as several supercomputing archtectures for image-based wavefront sensing. Timing results are also presented based on various algorithm implementations using a cluster of 64 TigerShare TSlOl DSP's (digital-signal processors).

Dean, Bruce H.↗
NASA NTRS2012

Multi-Scale Modeling of Magnetospheric Dynamics

Magnetic reconnection is a key element in many phenomena in space plasma, e.g. Coronal mass Ejections, Magnetosphere substorms. One of the major challenges in modeling the dynamics of large-scale systems involving magnetic reconnection is to quantifY the interaction between global evolution of the magnetosphere and microphysical kinetic processes in diffusion regions near reconnection sites. Recent advances in small-scale kinetic modeling of magnetic reconnection significantly improved our understanding of physical mechanisms controlling the dissipation in the vicinity of the reconnection site in collisionless plasma. However the progress in studies of small-scale geometries was not very helpful for large scale simulations. Global magnetosphere simulations usually include non-ideal processes in terms of numerical dissipation and/or ad hoc anomalous resistivity. Comparative studies of magnetic reconnection in small scale geometries demonstrated that MHD simulations that included non-ideal processes in terms of a resistive term 11 J did not produce fast reconnection rates observed in kinetic simulations. In collisionless magnetospheric plasma, the primary mechanism controlling the dissipation in the vicinity of the reconnection site is nongyrotropic pressure effects with spatial scales comparable with the particle Larmor radius. We utilize the global MHD code BATSRUS and replace ad hoc parameters such as "critical current density" and "anomalous resistivity" with a physically motivated model of dissipation. The primary mechanism controlling the dissipation in the vicinity of the reconnection site in incorporated into MHD description in terms of non-gyrotropic corrections to the induction equation. We will demonstrate that kinetic nongyrotropic effects can significantly alter the global magnetosphere evolution. Our approach allowed for the first time to model loading/unloading cycle in response to steady southward IMF driving. The role of solar wind parameters and ionospheric conductance on the dynamics of the loading/unloading cycle will be discussed.

Kuznetsova, M. M.↗
DOE OSTI2021

4D Proxy Imaging of Fracture Dilation and Stress Shadowing Using Electrical Resistivity Tomography During High Pressure Injections into a Dense Rock Formation

Fluid flow through fractured rock systems is governed in large part by the distribution, interconnectivity, and size of fracture apertures. In-situ stress is one of the primary factors controlling fracture aperture, and one that is altered significantly during high-pressure fluid injections or extractions. Interactions between stress, pore pressure, aperture, and fluid flow can result in complex and evolving poroelastic behavior with significant implications regarding the predictability and risk of developing and managing deep subsurface reservoirs (geothermal, fossil energy, and geologic carbon sequestration). In saturated crystalline rocks, bulk electrical conductivity is highly sensitive to porosity, and therefore to fracture aperture size and distribution. We demonstrate the use of time-lapse 3D electrical resistivity tomography for remotely monitoring stress induced changes in aperture distribution during high pressure injections into a fractured rock system at a scale of tens of meters. Results reveal a complex and continuously evolving stress field involving aperture dilations in the natural fracture system and aperture contractions in adjacent zones of shadow stress. Results provide information about the spatiotemporal changes in the system behavior and point to the potential of electrical imaging for autonomously and remotely monitoring evolving stress conditions by proxy through changes in bulk electrical conductivity.

electrical resisitivity tomography, stress, 4D Tim↗
NASA NTRS2007

Analysis of Eddy Current Capabilities for the Detection of Outer Diameter Stress Corrosion Cracking in Small Bore Metallic Structures

The use of eddy current techniques for the detection of outer diameter damage in tubing and many complex aerospace structures often requires the use of an inner diameter probe due to a lack of access to the outside of the part. In small bore structures the probe size and orientation are constrained by the inner diameter of the part, complicating the optimization of the inspection technique. Detection of flaws through a significant remaining wall thickness becomes limited not only by the standard depth of penetration, but also geometrical aspects of the probe. Recently, an orthogonal eddy current probe was developed for detection of such flaws in Space Shuttle Primary Reaction Control System (PRCS) Thrusters. In this case, the detection of deeply buried stress corrosion cracking by an inner diameter eddy current probe was sought. Probe optimization was performed based upon the limiting spatial dimensions, flaw orientation, and required detection sensitivity. Analysis of the probe/flaw interaction was performed through the use of finite and boundary element modeling techniques. Experimental data for the flaw detection capabilities, including a probability of detection study, will be presented along with the simulation data. The results of this work have led to the successful deployment of an inspection system for the detection of stress corrosion cracking in Space Shuttle Primary Reaction Control System (PRCS) Thrusters.

Wincheski, Buzz↗
NASA NTRS1971

A simple executive for a fault-tolerant, real-time multiprocessor.

Description of a simple executive for operation with a fault-tolerant multiprocessor that is oriented toward application in an environment where the primary function is to provide real-time control. The primary executive function is to accept requests for jobs placed by other jobs or from peripheral equipment and then schedule their initiation in accordance with the request parameters. The executive is also brought into action when a processor fails, so that appropriate disposition may be made of the job that was running on the failed processor. Many architectural features intended to support this executive concept are included.

Filene, R. J.↗
NASA NTRS2009

Physics of Reconnection and MMS Mission

Reconnection is the most important process driving the Earth's magnetosphere. Key to the success of the MMS science plan is the coupling of theory and observation. Determining the kinetic processes occurring in the diffusion region and physical parameters that control the rate of magnetic reconnection are among primary objectives of the MMS mission. Analysis of the role played by particle inertial effects in the diffusion region where the plasma is unmagnetized will be presented. The reconnection electric field in he diffusion region is supported primarily by particle non-gyrotropic effects. At the quasi-steady stage the reconnection electric field serves to accelerate and heat the incoming plasma population to maintain the current flow in the diffusion region the pressure balance. The primary mechanism controlling the dissipation in the vicinity of the reconnection site is incorporated into the fluid description in terms of non-gyrotropic corrections to the. induction and energy equations. The results of kinetic and fluid simulations illustrating the physics of magnetic reconnection will be presented. We will dem~:tistrate that kinetic nongyrotropic effects can significantly alter the global magnetosphere evolution and location of reconnection sites.

Kuznetsova, M. M.↗
NASA NTRS1979

Electromechanical flight control actuator

The feasibility of using an electromechanical actuator (EMA) as the primary flight control equipment in aerospace flight is examined. The EMA motor design is presented utilizing improved permanent magnet materials. The necessary equipment to complete a single channel EMA using the single channel power electronics breadboard is reported. The design and development of an improved rotor position sensor/tachometer is investigated.

Source record↗
NASA NTRS1993

Space Shuttle reaction control system thruster metal nitrate removal and characterization

The Space Shuttle hypergolic primary reaction control system (PRCS) thrusters continue to fail-leak or fail-off at a rate of approximately 1.5 per flight, attributed primarily to metal nitrate formation in the nitrogen tetroxide (N2O4) pilot operated valves (POV's). The failures have continued despite ground support equipment (GSE) and subsystem operational improvements. As a result, the Johnson Space Center (JSC) White Sands Test Facility (WSTF) performed a study to characterize the contamination in the N204 valves. This study prompted the development and implementation of a highly successful flushing technique using deionized (DI) water and gaseous nitrogen (GN2) to remove the contamination while minimizing Teflon seat damage. Following flushing a comprehensive acceptance test is performed before the thruster is deemed recovered. Between the time WSTF was certified to process flight thrusters (March 1992) and September 1993, a 68 percent thruster recovery rate was achieved. The contamination flushed from these thrusters was analyzed and has provided insight into the corrosion process, which is reported in this publication. Additionally, the long-term performance of 24 flushed thrusters installed in the WSTF Fleet Leader Shuttle reaction control subsystem (RCS) test articles is being assessed. WSTF continues to flush flight and test article thrusters and compile data to investigate metal nitrate formation characteristics in leaking and nonleaking valves.

Saulsberry, R. L.↗
DOE OSTI2020

Control of Output Power in Primary Side LCC and Secondary Series Tuned Wireless Power Transfer System without Secondary Side Sensors

The output power of a wireless power transfer (WPT) system varies with load and coupling factor of the inductively coupled coils. This paper presents a method to control the output power of primary side LCC and secondary side series tuned WPT system using information of primary side variables. In this approach, a secondary side control system or secondary side sensors are not needed. Detailed mathematical derivations are given to identify and justify the suitable primary side variable that accomplishes the desired purpose without the need of any secondary side communications. Simulation results presented validate the proposed scheme.

Mukherjee, Subho↗
NASA NTRS1973

Fluidic emergency roll control system

A fluidic emergency roll control system for aircraft stabilization in the event of primary flight control failure was evaluated. The fluidic roll control units were designed to provide roll torque proportional to an electrical command as operated by two diametrically opposed thrust nozzles located in the wing tips. The control package consists of a solid propellant gas generator, two diametrically opposed vortex valve modulated thrust nozzles, and an electromagnetic torque motor. The procedures for the design, development, and performance testing of the system are described.

Haefner, K. B.↗
NASA NTRS1980

Retrieval techniques: LVLH and inertially stabilized payloads

Procedures and techniques are discussed for retrieving payloads that are inertially or local vertical/local horizontal (LVLH) stabilized. Selection of the retrieval profile to be used depends on several factors: (1) control authority of the payload, (2) payload sensitivity to primary reaction control system (PRCS) plumes, (3) whether the payload is inertially or LVLH stabilized, (4) location of the grapple fixture, and (5) orbiter propellant consumption. The general retrieval profiles recommended are a V-bar approach for payloads that are LVLH or gravity-gradient stabilized, and the V-bar approach with one or two phase flyaround for inertially stabilized payloads. Once the general type of profile has been selected, the detailed retrieval profile and timeline should consider the various guidelines, groundrules, and constraints associated with a particular payload or flight. Reaction control system (RCS) propellant requirements for the recommended profiles range from 200 to 1500 pounds, depending on such factors as braking techniques, flyaround maneuvers (if necessary), and stationkeeping operations. The time required to perform a retrieval (starting from 1000 feet) varies from 20 to 130 minutes, depending on the complexity of the profile. The goals of this project are to develop a profile which ensures mission success; to make the retrieval profiles simple; and to keep the pilot workload to a minimum by making use of the automatic features of the orbiter flight software whenever possible.

Yglesias, J. A.↗
DOE OSTI2021

Energy-saving potential evaluation for primary schools with occupant-centric controls

Recent studies demonstrated that there is significant energy-saving potential for primary schools, which heating, ventilation, and air-conditioning (HVAC) systems with occupant-centric control (OCC) is an excellent candidate to save energy. However, such an energy impact has yet to be evaluated for different climate zones as well as different energy code versions, but is critical for technology transfer and deployment. Therefore, this paper conducts comprehensive evaluation on the energy-saving potentials for the primary schools with two advanced OCC strategies: presence-based and counting-based. In this work, ninety-six building energy models with stochastic behavior of occupants are developed and simulated, which consist of two building energy code versions, 16 climate zones, and baseline case (without OCC) and two advanced cases (with OCC). To evaluate the energy saving potentials for OCC, primary schools in the U.S. are used as an example. The results show that there is significant energy-saving potential for primary schools by considering OCC strategies, especially the counting-based case. The energy-saving potential is up to 10.2% for presence-based OCC and 12.41% for counting-based OCC. Furthermore, both climate and code version have a significant impact on energy savings from OCC strategies. The energy-saving potentials vary from 1.79% to 12.41% for different climates and code versions. This evaluation can also contribute to quantify the nationwide energy saving potential for other countries.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
NASA NTRS1973

Apollo experience report: Guidance and control systems - Digital autopilot design development

The development of the Apollo digital autopilots (the primary attitude control systems that were used for all phases of the lunar landing mission) is summarized. This report includes design requirements, design constraints, and design philosophy. The development-process functions and the essential information flow paths are identified. Specific problem areas that existed during the development are included. A discussion is also presented on the benefits inherent in mechanizing attitude-controller logic and dynamic compensation in a digital computer.

Peters, W. H.↗
NASA NTRSDate not supplied

Flight Dynamics Conceptual Design Exploration of Multirotor eVTOL

The advent of electric propulsion is revolutionizing the paradigm of rotorcraft design, leading to new electric Vertical Take-Off and Landing (eVTOL) aircraft. Direct drive topologies are common within these new designs, and some designers have chosen to utilize this mechanism for Primary Flight Control (PFC), effectively utilizing the aircraft engines as PFC actuators to control the speed of the rotors. This decision integrates the propulsion and flight control systems, and intrinsically couples the aircraft sizing and control. Four separate tools were exercised throughout this study to conduct a conceptual design exploration of eVTOL aircraft handling qualities. The main tasks for these tools were: 1) aircraft sizing and performance analysis, including the calculation of trim; 2) flight dynamics modeling and analysis; 3) handling qualities-centric control law optimization; and 4) electric motor sizing. Sizing of an RPM- controlled Hexacopter concept explored the dependency of aircraft size to fundamental design parameters: 1) disk loading and 2) blade loading coefficient. Increasing the design disk loading resulted in designs with high agility, but at the cost of significant growth in the design gross weight. Finally, Categories II and III pilot-induced-oscillation (PIO) are known potentially-catastrophic handling qualities deficiencies of fly-by-wire flight control systems such as those expected of eVTOL aircraft. Consideration of PIO predictive metrics in conceptual design control synthesis led to increased PIO robustness.

Flight Dynamics↗
NASA NTRS1985

Space shuttle rudder/speedbrake actuation subsystem

The Rudder/Speedbrake (R/SB) Actuation Subsystem for use on the NASA Space Shuttle Orbiter is an electro-hydro-mechanical system which provides the control and positionary capability of the orbiter aero-dynamic primary flight control surface. The system is located in the vehicle's vertical stabilizer. The geared rotary actuators provide a power hinge feature of the split panel rudder. Actuation of both panels in the same direction provides conventional rudder control; actuating the panels differentially provides a speedbrake function intended to control both speed and pitch. The commands may be superimposed on one another. The system consists of one power drive unit which responds to quadredundant avionic signals to generate a rotary output, four geared rotary actuators, which develop rotary position and torque as outputs, and ten torque transmitting drive-shifts.

Naber, R. A.↗