Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “power density”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

3.5 kW/in3 Planar Coupled Inductor Design and Optimization for a 50 kW 3-level Four-Switch Buck-Boost (3L-FSBB) Converter

Planar magnetics design has been widely used in power electronics field because of the low profile, ease of manufacturability, and high power density. This paper first proposes a 3-level four-switch buck-boost (3L-FSBB) converter for the dc-dc applications where the zero common-mode (CM) voltage emissions, step-up and step-down are all required. With the consideration of power density, efficiency, and cost, a 15oz heavy copper coupled inductor for 3-level FSBB converter was designed and optimized with the low-cost commercial core and planar windings. According to the soft-switching quadrangle modulation for 3-L FSBB, the turns number and stacked core number are optimized first. And then, a two-board design is proposed to reduce the fringing effect and improve the thermal performance. Finally, a 75 kVA two-stage ac-dc-dc converter including a 3-level FSBB converter was built to verify the electrical design.

Cao, Yuliang↗
DOE OSTI2021

Porphyrin Aerogel Catalysts for Oxygen Reduction Reaction in Anion-Exchange Membrane Fuel Cells

Platinum group metal (PGM)-free catalysts for oxygen reduction reaction have shown high oxygen reduction reaction activity in alkaline media. In order to further increase the power density of anion-exchange membrane fuel cells (AEMFCs), PGM-free catalysts need to have a high site density to reach high current densities. In this work, synthesis, characterization, and utilization of heat-treated iron porphyrin aerogels are reported as cathode catalysts in AEMFCs. The heat treatment effect is thoroughly studied and characterized using several techniques, and the best performing aerogel is studied in AEMFC, showing excellent performance, reaching a peak power density of 580 mW cm –2 and a limiting current density of as high as 2.0 A cm –2 , which can be considered the state-of-the-art for PGM-free based AEMFCs.

25 ENERGY STORAGE↗
DOE OSTI2021

Thin THz QCL active regions for improved continuous-wave operating temperature

We compare the performance of 10 and 5 μm thick metal–metal waveguide terahertz quantum-cascade laser ridges operating around 2.7 THz and based on a 4-well phonon depopulation active region design. Thanks to reduced heat dissipation and lower thermal resistance, the 5 μm thick material shows an 18 K increase in continuous wave operating temperature compared to the 10 μm material, despite a lower maximum pulsed-mode operating temperature and a larger input power density. A maximum continuous wave operating temperature of 129 K is achieved using the 5 μm thick material and a 15 μm wide ridge waveguide, which lased up to 155 K in the pulsed mode. The use of thin active regions is likely to become increasingly important to address the increasing input power density of emerging 2- and 3-well active region designs that show the highest pulsed operating temperatures.

47 OTHER INSTRUMENTATION↗
DOE OSTI2021

High-performance ammonia oxidation catalysts for anion-exchange membrane direct ammonia fuel cells

Low-temperature direct ammonia fuel cells (DAFCs) use carbon-neutral ammonia as a fuel, which has attracted increasing attention recently due to ammonia's low source-to-tank energy cost, easy transport and storage, and wide availability. However, current DAFC technologies are greatly limited by the kinetically sluggish ammonia oxidation reaction (AOR) at the anode. Herein, we report an AOR catalyst, in which ternary PtIrZn nanoparticles with an average size of 2.3 ± 0.2 nm were highly dispersed on a binary composite support comprising cerium oxide (CeO 2 ) and zeolitic imidazolate framework-8 (ZIF-8)-derived carbon (PtIrZn/CeO 2 -ZIF-8) through a sonochemical-assisted synthesis method. Additionally, the PtIrZn alloy, with the aid of abundant OH ad provided by CeO 2 and uniform particle dispersibility contributed by porous ZIF-8 carbon (surface area: ~600 m 2 g -1 ), has shown highly efficient catalytic activity for the AOR in alkaline media, superior to that of commercial PtIr/C. The rotating disk electrode (RDE) results indicate a lower onset potential (0.35 vs. 0.43 V), relative to the reversible hydrogen electrode at room temperature, and a decreased activation energy (~36.7 vs. 50.8 kJ mol -1 ) relative to the PtIr/C catalyst. Notably, the PtIrZn/CeO 2 -ZIF-8 catalyst was assembled with a high-performance hydroxide anion-exchange membrane to fabricate an alkaline DAFC, reaching a peak power density of 91 mW cm -2 . Unlike in aqueous electrolytes, supports play a critical role in improving uniform ionomer distribution and mass transport in the anode. PtIrZn nanoparticles on silicon dioxide (SiO 2 ) integrated with carboxyl-functionalized carbon nanotubes (CNT–COOH) were further studied as the anode in a DAFC. A significantly enhanced peak power density of 314 mW cm -2 was achieved. Density functional theory calculations elucidated that Zn atoms in the PtIr alloy can reduce the theoretical limiting potential of *NH 2 dehydrogenation to *NH by ~0.1 V, which can be attributed to a Zn-modulated upshift of the Pt–Ir d-band that facilitates the N–H bond breakage.

25 ENERGY STORAGE↗
DOE OSTI2022

Titanium Material Comparison for Second Target Station Moderators

Two titanium alloys, Ti 15-3-3-3 and Grade 5 Ti, have been analyzed for their neutronic differences after being exposed to neutron fluxes from a 5-year operational period in the Second Target Station (STS)moderators. There are several differences in the original composition of the two alloys where Ti 15-3-3-3contains Cr and Sn and Grade 5 Ti does not. The differences in original composition propagate through the analysis to yield discrepancies in decay power density and decay gamma intensity density of more than a factor of 3.5 at some times during operation. Immediately after the 5-year operational period, Ti 15-3-3-3has a factor of 3.59 higher intensity of high-energy decay gammas than Grade 5 Ti, and Ti 15-3-3-3 also has a factor of 3.53 higher decay power than Grade 5 Ti. After 1 year of shutdown, Ti 15-3-3-3 has a 48% higher intensity of high-energy decay gammas and a 86% greater decay power density when compared with Grade 5 Ti. The quantities-of-interest in this report are per unit volume and the overall volume of titanium should be considered when making engineering judgment on final titanium alloy selection.

36 MATERIALS SCIENCE↗
DOE OSTI2021

VTO_2021_APR_LLNL_Ye

Traditional batteries are composed of two-dimensional films that are stacked and/or rolled. Thin film batteries display high power density while their thick film counterparts show good energy density, but it has proven difficult to concurrently achieve both within these planar form factors. In addition, conventional Li-ion batteries based on liquid organic electrolytes or gel polymer electrolytes have raised severe safety concerns due to the intrinsic flammable properties of the organic electrolytes. They are also not ideal for the use of high energy density metallic lithium (Li) anodes due to Li dendrite growth, or sulfur cathodes due to shuttling effects that result in fast capacity fade. There is an urgent need to develop safe, high-performance solid-state batteries (SSBs) with advanced electrolyte and separator technologies. Although in recent years a series of superionic conductors have been developed for electrolytes and separators, their performance does not satisfy demanding criteria due to large impedance from poor solid electrolyte-electrode contact and questionable electrochemical and mechanical stability. Unlike the well-established roll-to-roll fabrication of conventional Li-ion batteries, the processing of SSBs is unique due to the brittleness of solid-state electrolytes (SSEs). The commercially available or lab-developed SSE discs are usually very thick (hundreds of micrometers to millimeters) to overcome their brittle nature, which unfortunately increases the cell impedance and accounts for the majority of the overall cell weight and volume, leading to dramatically decreased power and energy densities. In this project, we will investigate 3D printing techniques to overcome safety, fabrication, mechanical, and electrochemical issues in SSBs. 3D printing builds complex structures in a layer-by-layer fashion, which allows rapid production of hierarchical architectures, gradient and multi-material structures, and multi-component assemblies. 3D printing is an emerging area that could fundamentally transform energy storage devices. For example, 3D printing can produce batteries with arbitrary form factors to fit a product’s specific volume requirements and can create interwoven electrode arrangements over a wide range of length scales to improve transport and increase power density for a given energy density. For SSBs, 3D printing may dramatically reduce the separator thickness from ~1 mm (by hydraulic pressing) to tens of micrometers or less. In addition, the interfacial contact area between the electrolyte and the electrode may be increased via 3D interdigitated designs. Hence, we expect a significant reduction of the overall cell impedance and enhancement of both energy and power densities of SSBs by harnessing an array of 3D printing technologies being developed at Lawrence Livermore National Laboratory (LLNL).

25 ENERGY STORAGE↗
DOE OSTI2022

Westinghouse advanced fuel management strategies leveraging high enrichment and high burnup fuel to optimize PWR economics

In the US, nuclear power plants have been focused on increasing electricity generation for over three decades via longer operating cycles, reduced number of outages and duration, and the implementation of power up-rates. The potential for zero-carbon emission credits and other carbon-reduction initiatives further makes nuclear power utilities to focus on increasing generation capability. Longer operating cycles provide increased energy generation and enable economic savings to nuclear utilities when the increase in fuel loading required to achieve the extended cycle energy target and resulting increase in total fuel cost is offset by the savings from outage avoidance and reduced replacement power costs. For the current licensed limits of 5 w/o {sup 235}U enrichment and 62 GWd/tU peak pin burnup, higher power density PWR plants, which are prevalent in the PWR fleet, require an excessively penalizing fraction of feed fuel assemblies to operate for the extended cycle duration, with inevitably poor fuel use and fuel cycle economics that cannot be counterbalanced by the savings on outage cost avoidance. To overcome this barrier, the nuclear industry is pursuing development of high enrichment/high burnup fuel technology ({sup 235}U enrichment up to 8 w/o and peak pin burnup up to 75 GWd/tU) which increases fuel energy generation capability and can enable high power density plants to achieve positive economics on 24-month cycle of operation. This paper presents advanced fuel management strategies developed by Westinghouse to enable transition of PWR reactors from 18-month to 24-month cycle of operation, with and without a core thermal power uprate, which are then used as basis to assess the economics of a direct transition from 18 to 24-month cycles with high enrichment/high burnup fuel. The results show that these fuel management strategies, especially if coupled with thermal power up-rates, present the opportunity for substantial economic benefits to utilities. The systematic review of fuel management strategies presented can provide an illustrative reference for decision makers as they consider how to maximize nuclear energy generation economically. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Self-Anchored Platinum-Decorated Antimony-Doped-Tin Oxide as a Durable Oxygen Reduction Electrocatalyst

The lifetime of commercial Proton Exchange Membrane Fuel Cells (PEMFCs) is circumscribed by the insufficient durability of commercial catalysts. The use of metal oxide supports in place of carbon significantly increases electrocatalyst durability. Herein, following density functional theory (DFT) predictions of improved Platinum (Pt) stability on antimony doped tin oxide (ATO) supports, we synthesized ATO whose morphology and crystal structure was engineered using a Pt anchoring technique. X-ray photoelectron spectroscopy (XPS) indicated that the Pt anchor sites aided in the reduction of Pt precursors to Pt on the ATO surface. X-ray absorption near-edge spectroscopy (XANES) revealed the existence of strong-metal-support interactions (SMSI) between Pt and ATO. The combination of SMSI and high control over Pt dispersion enabled the Pt/Pt-aerogel-ATO (Pt supported on aerogel ATO with Pt anchor sites) electrocatalyst to achieve 2x the area specific activity of Pt/C in ex-situ testing. In a H 2 /air PEMFC Pt/Pt-aerogel-ATO cathodes enabled 20% higher peak power density and <1/6 the loss of active surface area as compared to Pt/C. Notably, in a PEMFC under rigorous potential cycling, the Pt/Pt-aerogel-ATO retained its initial peak power density as opposed to a 58% loss for Pt/C. Further, cost models indicate that Pt/Pt-aerogel-ATO is 26% less expensive than Pt/C over its useful lifetime.

25 ENERGY STORAGE↗
DOE OSTI2022

An additively-manufactured molten salt-to-supercritical carbon di-oxide primary heat exchanger for solar thermal power generation – Design and techno-economic performance

The design and techno-economic performance of a compact additively manufactured (AM) molten salt (MS)-to-supercritical carbon di-oxide (sCO2) primary heat exchanger (PHE) for solar thermal application is described. The PHE design consists of sCO2 flow through an array of microscale pin fins while the MS flows through mm-scale rectangular channels. Constraints imposed by AM using laser powder bed fusion method are considered in the design. Structural and fluid flow simulations are performed to arrive at a viable design of the core and headers. A simplified one-dimensional steady state model for the PHE is developed including the impact of surface roughness from the AM process. A process-based cost model is used to determine the tradeoff between thermofluidic design and manufacturing cost. A parametric study is performed using the thermo-fluidic and cost models to determine the set of geometrical and flow variables that result in high power density and low cost, while restricting the pressure drop on the sCO2 side to less than 2% of line pressure. Flow rates of MS and sCO2 were varied over heat capacity rate ratios ranging from 0.2 to 1. Results indicate that it is possible to design a low-pressure drop AM PHE with an effectiveness of 90% and a power density in excess of 10 MW/m3 (including headers). Fabrication of representative nickel superalloy specimens are shown to demonstrate that low-porosity parts with the requisite dimensional tolerance of PHE core can be generated.

14 SOLAR ENERGY↗
DOE OSTI2021

Design of a 2 MW ZrC/W-based molten-salt-to-sCO 2 PCHE for concentrated solar power

To increase the power cycle efficiency and lower the levelized cost of electricity (LCOE) of concentrated solar power (CSP) plants, printed circuit heat exchangers (PCHEs) capable of operating above 700 °C with molten chloride salt and a sCO 2 -based fluid are needed. In this paper, the design of a high-pressure, high-temperature, 2 MW PCHE comprised of a thermomechanically-robust, zirconium carbide/tungsten (ZrC/W) composite is conducted for CSP plants. The ZrC/W composite is a material with high thermal conductivity, high stiffness, and high failure strength at high temperatures, along with excellent resistance to thermal cycling and thermal shock. In this work, a thermomechanical design analysis was conducted to select appropriate material thicknesses of the ZrC/W plates, and to determine the geometrical dimensions and the thermal performance of the PCHE. The influences of the plate number and heat exchanger length on power density and pressure drop have also been systematically investigated. Economic analyses were conducted to compare the cost of ZrC/W-based PCHEs to those comprised of IN740H (a state-of-the-art, nickel-based superalloy) and 316 stainless steel (316SS). Finally, at a sufficiently high plate production rate, the manufacturing cost of ZrC/W-based PCHEs can be significantly lower, while achieving a much higher power density, compared with state-of-the-art, nickel alloy-based and stainless steel-based PCHEs.

14 SOLAR ENERGY↗
DOE OSTI2023

System efficiency and power assessment of the all-aqueous copper thermally regenerative ammonia battery

Thermally regenerative ammonia batteries (TRABs) use low-temperature (T < 100 °C) heat to provide stationary energy and power with higher power densities and efficiency relative to other waste heat devices. TRABs are an active area of research in waste heat devices, but currently there is little consensus on what aspect of the system is limiting TRAB performance and what maximum efficiencies are possible. Experiments and numerical models were used here to examine the sensitivity of the battery and distillation column in a TRAB system to key operating variables, thereby establishing practical limits and identifying focus areas for improving performance. Battery power was eight times more sensitive to ohmic losses than kinetic and mass transfer losses, regardless of the operating temperature, and the peak power density was simulated to be 18.8 mW cm –2 at 75 °C. Theoretical energy efficiency limits were defined for a series of ammonia concentrations and operating pressures, ranging from 5 – 12%, which is 2–3 times higher than previous experimental estimations. Atmospheric pressure column operation used a larger amount of waste heat compared to sub-atmospheric pressure. It is estimated that the volume of the battery would take up 9.2m 3 for every 1% of the power output of a natural gas turbine, but with realistic improvements to cell conductivity, the size would reduce to 2.5 m 3 . Finally, the results presented in this work will help streamline future development by focusing on minimizing ohmic losses and provide specific data for full system evaluation of future TRABs.

25 ENERGY STORAGE↗
DOE OSTI2020

Direct processing of PbZr 0.53 Ti 0.47 O 3 films on glass and polymeric substrates

This work reports on direct crystallization of PbZr 0.53 Ti 0.47 O 3 (PZT) thin films on glass and polymeric substrates, using pulsed thermal processing (PTP). Specifically, xenon flash lamps deliver pulses of high intensity, short duration, broadband light to the surface of a chemical solution deposited thin film, resulting in the crystallization of the film. Structural analysis by X-ray diffraction (XRD) and transmission electron microscopy show the existence of perovskite structure in nano-sized grains (≤5 nm). Local functional analysis by band excitation piezoelectric spectroscopy and electrostatic force microscopy confirm the presence of a ferroelectric phase and retention of voltage-written polarization for multiple days. Based on structural and functional analyses, strategies are discussed for optimization of pulse voltage and duration for the realization of crystalline ferroelectric thin films. For ~200 nm-thick PZT films on glass substrates, 500 μs-long pulses were required for crystallization, starting with 100 pulses at 350 V, 10 or 25 pulses at 400 V and in general lower number of pulses at higher voltages (resulting in higher radiant energy). Overall power densities of >6.4 kW/cm 2 were needed for appearance of peaks corresponding to the perovskite phase in the XRD. Films on glass processed at 350–400 V had a higher degree of 111-oriented perovskite grains. Higher applied radiant energy (through increased pulse voltage or count) resulted in more random and/or partially 001-oriented films. For ~1 μm-thick PZT films on polymeric substrates, 10 to 25 250 μs-long pulses at voltages ranging between 200 to 250 V, corresponding to power densities of ~2.8 kW/cm 2 , were optimal for maximized perovskite phase crystallization, while avoiding substrate damage.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Machine learning models for volumetric swelling in uranium nitride

Machine learning methods are applied to predict the volumetric swelling rate of the nuclear fuel uranium nitride (UN) over various temperatures, irradiation conditions, and power densities. Both kernel-based methods and symbolic regression models for UN swelling are developed and compared with multiple experimental datasets. We find that the UN pellet geometry and dimensions must be taken into account to accurately model swelling behavior. Strong agreement is observed between the developed machine learning models and the data. The predictive error generated by the machine learning models improves on empirical models taken from the literature. Sensitivity analysis is performed to determine which properties such as temperature, burnup, and power density, are most important in the swelling process. We find that machine learning can be used to quickly develop accurate swelling models for nuclear materials. In conclusion, the presented results illustrate the potential of machine learning to determine volumetric swelling in UN.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

High Performance PEFC Electrode Structures

Raytheon Technologies Research Center (RTRC) in collaboration with Ion Power Inc. and the University of Arkansas at Little Rock and the FC-PAD consortium executed a project that: (1) developed comprehensive models of oxygen and proton transport in cathode catalyst layers that provided new insights about losses associated with reducing platinum loading to 0.1 mg/cm 2 , (2) designed, fabricated, characterized, and tested cells featuring carbon-supported catalyst layers with low platinum loadings that met efficiency and power density targets set forth by the Hydrogen and Fuel Cells Technology Office, and (3) designed, fabricated, characterized, and tested novel catalyst structures. The modeling efforts produced eight scientific publications that shared new descriptions of oxygen and proton transport in catalyst layers with the broader technical community. The key physical insights from the models are expressed in straightforward algebraic expressions, facilitating easy adoption by other researchers. The models developed during the project explain why resistance to oxygen transport is inversely proportional to interfacial area of platinum – an observation that eluded quantitative explanation for a decade. The models quantitatively predict polarization when measured morphological parameters and transport properties are input. Membrane-electrode assemblies made during the project met stated goals for current at high voltage and power density at rated voltage for transportation fuel cells at the end of budget period 2. High performance was achieved by developing a diffusion layer with low resistance to oxygen transport and a PtCo/C cathode catalyst layer capable of supporting rapid proton and oxygen transport. The project was subsequently directed to curtail experimental work and focus on modeling during budget period 3. Ion Power Inc. developed new expertise in fabricating catalyst layers containing platinum-cobalt catalysts, and processing very thin membranes. The University of Arkansas at Little Rock developed novel nanocolumnar self-supported thin film electrocatalysts that can be grown on carbon supports using a simple high pressure sputter deposition method. The nanocolumnar microstructure provides adequate surface-to-volume ratio for efficient platinum utilization, and the conformal platinum shell with larger crystal grain sizes covering the carbon support surface may eliminate durability issues associated with catalyst dissolution, agglomeration, and carbon corrosion.

08 HYDROGEN↗
DOE OSTI2020

Boosting solid oxide fuel cell performance via electrolyte thickness reduction and cathode infiltration

Increasing the power density and reducing the operating temperature of solid oxide fuel cells (SOFCs) is important for improving commercial viability. Here we discuss two strategies for achieving such improvements in Ni–YSZ supported SOFCs – electrolyte thickness reduction and cathode infiltration. Microstructural and electrochemical results are presented showing the effect of reducing YSZ/GDC electrolyte thickness from 8 to 2.5 μm, and the effect of PrO x infiltration into the LSCF–GDC cathode. Both of these measures are effective, particularly at lower temperatures, leading to an increase in the maximum power density at 650 °C from 0.4 to 0.95 W cm –2 , for example. Electrochemical impedance spectroscopy utilizing subtractive analysis shows that PrO x enhances the cathode charge transfer process. Reducing the electrolyte thickness reduces not only the cell ohmic resistance but also the electrode polarization resistance. Furthermore, the latter effect appears to be an artifact associated with a slight increase in the steam partial pressure at the anode due to minor gas leakage across the thinner electrolyte.

25 ENERGY STORAGE↗
DOE OSTI2020

Boosting energy efficiency of Li-rich layered oxide cathodes by tuning oxygen redox kinetics and reversibility

In developing electrode materials for next-generation Li-ion batteries, significant efforts have been given to the energy, power density and cycling stability, with much less (if any) attention paid to the energy efficiency – arguably, the most important practical measure for large-scale applications. This is particularly true for the oxygen-redox active electrodes, such as Li 1.2 Ni 0.13 Co 0.13 Mn 0.54 O 2 , the notorious energy-inefficient cathode that has an extremely high capacity but comes with large voltage hysteresis and voltage decay. Herein, we report the rational design of an energy-efficient Li-rich layered cathode along with high energy, power density and cycling stability enabled by tuning oxygen redox activity. Specifically, the target material Li 1.12 Ni 0.22 Co 0.13 Mn 0.52 O 2 exhibits an ultrahigh energy efficiency at 1 C (90.6%), high capacity (> 200 mAh g -1 ) with 98.9% retention and less than 150 mV decay at the extended 200 cycles. Overall, through direct comparison between the material and Li 1.2 Ni 0.13 Co 0.13 Mn 0.54 O 2 , we show that the compositional change, although slightly, greatly improves the oxygen redox kinetics and reversibility, thereby boosts energy efficiency. The findings offer a strategy to narrow the gap between scientific interest and practical application of oxygen-redox chemistry.

36 MATERIALS SCIENCE↗
DOE OSTI2020

LCOE Design Optimization Using Genetic Algorithm with Improved Component Models for Medium-Voltage Transformerless PV Inverters

For real-world installations of photovoltaic and other renewable energy resources, the critical design metric is the levelized cost of energy (LCOE); however, many power electronics design optimizations are performed with efficiency and power density as the primary design goals. Recent work has shown that a new LCOE-focused optimization approach can yield improved system designs balancing cost and energy generation. This paper expands the LCOE optimization approach by considering comprehensive optimization parameters, adding new modeling of inductor cost, extending the semiconductor model to include effects of losses on housing cost, and implementing a genetic algorithm to improve computation efficiency.

41 EE - Solar Energy Technologies Office (EE-4S)↗
DOE OSTI2021

Fabrication and Characterization of Cross-Linked Phenyl-Acrylate-Based Ion Exchange Membranes and Performance in a Direct Urea Fuel Cell

Ion exchange membranes (IEMs) are crucial for direct fuel cells, including direct methanol and direct urea fuel cells (DUFCs). While commercially available IEMs (e.g., FAA-3-50) show decent power density in direct fuel cells, they experience considerable methanol or urea crossover, reducing device performance and motivating design of IEMs that suppress fuel crossover. Here, we prepare cross-linked IEMs with high mechanical toughness utilizing a cross-linker (methylenebis(acrylamide)), hydrophobic monomer (phenyl acrylate (PA) or phenyl methacrylate (PMA)), and charged monomer (2-acrylamido-2-methyl-1-propanesulfonic acid (AMPS) for cation exchange or methacroylcholine chloride (MACC) for anion exchange). To validate these membranes in a fuel cell application, we perform DUFC experiments utilizing a PA/MACC AEM and observe good power density compared to FAA-3-50. Furthermore, to understand the role of urea crossover in DUFC performance, permeabilities of both membranes to urea are measured by diffusion cells with in situ ATR-FTIR spectroscopy, where our PA/MACC exhibited lower urea permeability than FAA-3-50.

36 MATERIALS SCIENCE↗