Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “polymer composite”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

Quantifiable Assessment of SWNT Dispersion in Polymer Composites

NASA LaRC has established a new protocol for visualizing the nanomaterials in structural polymer matrix resins. Using this new technique and reconstructing the 3D distribution of the nanomaterials allows us to compare this distribution against a theoretically perfect distribution. Additional tertiary structural information can now be obtained and quantified with the electron tomography studies. These tools will be necessary to establish the structural-functional relationships between the nano and the bulk. This will also help define the critical length scales needed for functional properties. Field ready tool development and calibration can begin by using these same samples and comparing the response. i.e. gold standards of good and bad dispersion.

Park, Cheol↗

AC Electric Field Activated Shape Memory Polymer Composite

Shape memory materials have drawn interest for applications like intelligent medical devices, deployable space structures and morphing structures. Compared to other shape memory materials like shape memory alloys (SMAs) or shape memory ceramics (SMCs), shape memory polymers (SMPs) have high elastic deformation that is amenable to tailored of mechanical properties, have lower density, and are easily processed. However, SMPs have low recovery stress and long response times. A new shape memory thermosetting polymer nanocomposite (LaRC-SMPC) was synthesized with conductive fillers to enhance its thermo-mechanical characteristics. A new composition of shape memory thermosetting polymer nanocomposite (LaRC-SMPC) was synthesized with conductive functionalized graphene sheets (FGS) to enhance its thermo-mechanical characteristics. The elastic modulus of LaRC-SMPC is approximately 2.7 GPa at room temperature and 4.3 MPa above its glass transition temperature. Conductive FGSs-doped LaRC-SMPC exhibited higher conductivity compared to pristine LaRC SMP. Applying an electric field at between 0.1 Hz and 1 kHz induced faster heating to activate the LaRC-SMPC s shape memory effect relative to applying DC electric field or AC electric field at frequencies exceeding1 kHz.

Kang, Jin Ho↗

Aqueous-Based Polyimine Functionalization of Cellulose Nanofibrils for Effective Drying and Polymer Composite Reinforcement

Here a simple strategy was developed to synthesize polyimine-coated cellulose nanofibrils (CNF) for effective CNF drying and composite reinforcement. The polyimine was synthesized in an aqueous medium using a selective hydrophilic and hydrophobic component that forces the polyimine to precipitate, which prevents the reverse imine reaction. The polyimine coating allowed the CNF to be easily oven-dried while maintaining a fibrillar morphology to provide mechanical reinforcement in poly(ethylene terephthalate glycol) (PETG) composites. In comparison, poor mechanical performance and a heterogeneous fracture surface were observed when the coated CNF were incorporated into poly(l-lactide) (PLA) composites. It is hypothesized that intermolecular aromatic–aromatic interactions are formed at the interface between fibers and the polymer matrix in the PETG system, while no such phenomena occur in the PLA system. Overall, this facile strategy to produce modified, easily dried CNF can be adapted to produce polyimine-coated CNF with unique functionalities that are useful in a range of applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Simultaneous Improvement of Mechanical and Fire-Safety Properties of Polymer Composites with Phosphonate-Loaded MOF Additives

Flame-retardant (FR) additives are commonly used to improve the fire safety of synthetic polymers, which are widely employed in manufactured consumer goods. Incorporation of an FR in a polymer typically leads to deterioration of its mechanical properties. It also manifests itself in non-negligible volatile organic compound (VOC) release, which in turn increases environmental risks carried by both the application and disposal of the corresponding consumer goods. Herein, we present a hierarchical strategy for the design of composite materials, which ensures simultaneous improvement of both mechanical and fire-safety properties of polymers while limiting the VOC release. Our strategy employs porous metal–organic framework (MOF) particles to provide a multifunctional interface between the FR molecules and the polymer. Specifically, we demonstrate that the particles of environmentally friendly HKUST-1 MOF can be infused by a modern FR—dimethyl methylphosphonate (DMMP)—and then embedded into widely used unsaturated polyesters. The DMMP–HKUST-1 additive endows the resulting composite material with improved processability, flame retardancy, and mechanical properties. Single-crystal X-ray diffraction, thermogravimetric analysis, and computational modeling of the additive suggest the complete pore filling of HKUST-1 with DMMP molecules being bound to the open metal sites of the MOF.

36 MATERIALS SCIENCE↗

Chemical interaction and enhanced interfacial ion transport in a ceramic nanofiber–polymer composite electrolyte for all-solid-state lithium metal batteries

This article reports the synergy between ceramic nanofibers and a polymer, and the enhanced interfacial Li-ion transport along the nanofiber/polymer interface in a solid-state ceramic/polymer composite electrolyte, in which a three-dimensional (3D) electrospun aluminum-doped Li 0.33 La 0.557 TiO 3 (LLTO) nanofiber network is embedded in a polyvinylidene fluoride-hexafluoropropylene (PVDF-HFP) matrix. Strong chemical interaction occurs between the nanofibers and the polymer matrix. Addition of the ceramic nanofibers into the polymer matrix results in the dehydrofluorination of the PVDF chains, deprotonation of the –CH 2 moiety and amorphization of the polymer matrix. Solid-state nuclear magnetic resonance (NMR) spectra reveal that lithium ions transport via three pathways: (i) intra-polymer transport, (ii) intra-nanofiber transport, and (iii) interfacial polymer/nanofiber transport. In addition, lithium phosphate is coated on the LLTO nanofiber surface before the nanofibers are embedded into the polymer matrix. The presence of lithium phosphate at the LLTO/polymer interface further enhances the chemical interaction between the nanofibers and the polymer, which promotes the lithium ion transport along the polymer/nanofiber interface. This in turn improves the ionic conductivity and electrochemical cycling stability of the nanofiber/polymer composite. As a result, the flexible LLTO/Li 3 PO 4 /polymer composite electrolyte membrane exhibits an ionic conductivity of 5.1 × 10 -4 S cm -1 at room temperature and an electrochemical stability window of 5.0 V vs. Li/Li + . A symmetric Li|electrolyte|Li half-cell shows a low overpotential of 50 mV at a constant current density of 0.5 mA cm -2 for more than 800 h. In addition, a full cell is constructed by sandwiching the composite electrolyte between a lithium metal anode and a LiFePO 4 -based cathode. Such an all-solid-state lithium metal battery exhibits excellent cycling performance and rate capability.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Polymer composites prepared by low-temperature post-irradiation polymerization of C 2 F 4 in the presence of graphene-like material: synthesis and characterization

Polymer polytetrafluoroethylene (PTFE) microwave exfoliated graphene oxide (MEGO) composites containing up to 80 wt% PTFE were prepared by low-temperature post-irradiation polymerization of C2F4 in the presence of the graphene-like material. Composites were characterized by FTIR, NMR, XPS, SEM, TGA, XRD, broadband dielectric spectroscopy and DSC techniques. The melting point of PTFE in the composite (332.5 °C) was higher than that of pure PTFE by 8.8 C. The measured values of the melting enthalpy (ΔH m 51.5 and 45.4 J g1) were used to calculate the extent of crystallinity in the PTFE and PTFE MEGO composite (0.63 and 0.55, respectively). No CF3 end groups typical of commercial PTFE have been detected in the PTFE MEGO composites.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Li Morphology Evolution during Initial Cycles in a Gel Composite Polymer Electrolyte

Understanding and controlling lithium morphology evolution and lithium dendrite formation and growth during cycling is one of the key challenges for high-energy lithium metal batteries. This challenge applies to liquid electrolyte batteries as well as solid-state and semi-solid-state batteries. Our current knowledge about the evolution of the Li morphology is mostly obtained from liquid electrolyte-based studies in a Li–Li symmetrical cell configuration. The knowledge obtained in such conditions may not readily transfer into solid-state or semi-solid-state batteries. In this work, Li morphology evolution during initial cycling in a full cell configuration with the LiNi 0.6 Co 0.2 Mn 0.2 O 2 (NMC 622) cathode and a semi-solid-state gel composite electrolyte is monitored via post-mortem photographs and scanning electron microscopy at multiple length scales. The gel composite electrolyte contains a cross-linked poly(ethylene oxide)-based polymer electrolyte, ceramic fillers, and a liquid plasticizer. The results show that severe surface pitting occurs as early as the second stripping cycle. Pit formation and continuous dissolution during the stripping process are the main cause of the Li surface roughening and dendrite growth mechanism in the model gel composite electrolyte. Comparing Li dendrite growth mechanisms in liquid, polymer, and ceramic solid electrolytes, the dendrite growth mechanism observed in this model electrolyte resembles that of the liquid electrolyte the most. This study suggests that strategies to control Li morphology and prevent dendrite growth in a gel composite electrolyte should be similar to strategies applicable to liquid electrolytes.

25 ENERGY STORAGE↗

Lead-free halide double perovskite-polymer composites for flexible X-ray imaging

X-ray detectors are demonstrated using composite films of lead-free Cs 2 AgBiBr 6 halide double perovskite embedded in a polymer matrix as the X-ray photoconductors. Polymers with hydroxyl functional groups greatly improve the uniformity of the composite films, and large area dense films are obtained using a simple drop-casting process. X-ray detectors based on the composite films exhibit a sensitivity of 40 μC Gy air -1 cm -2 , comparable to the reported sensitivity using Cs 2 AgBiBr 6 single crystals. Such detectors can also tolerate a 5% tensile/compressive strain in the composite films without performance degradation. Pixelated X-ray detectors fabricated on the same composite film can realize X-ray imaging and resolve a proof-of-concept geometric pattern.

36 MATERIALS SCIENCE↗

Corrosion protection of steel pipelines with metal-polymer composite barrier liners

Pipelines are efficient in transporting natural gas over large distances. Wet carbon dioxide present in pipelines can create an environment that is corrosive to steel. Polymer liners made from either polyethylene or polyamide (nylon) are presently used to mitigate internal corrosion in natural gas pipelines. Gas diffuses through all polymers over time, and polymer-only liners lower the steel corrosion rate by reducing the reactive gas flux to the internal surface of a pipeline. Composite liners, which incorporate one or more metallic layers that are impermeable to corrosive gases, offer better protection than polymer-only liners. In this study, we measured the methane, water vapor, and carbon dioxide permeability of a multi-layer barrier film and found it to be more effective in resisting gas permeation than polyethylene and nylon-11 films.

03 NATURAL GAS↗

Shock compression of additively manufactured high solids loaded polymer composites with aligned porosity

The effects of aligned porosity on the shock-compression response of additively manufactured (AM) composite structures with collinear and log-cabin geometries are investigated. The composites contain two inorganic and two organic particle populations and a UV-curable polymer binder. X-ray phase contrast imaging (X-PCI) is used as an in-material diagnostic in plate-impact experiments performed at the Dynamic Compression Sector of the Advanced Photon Source at the Argonne National Laboratory. Macroscale shock and particle velocities and microscale pore collapse velocities are measured from X-PCI images obtained from samples impacted in various orientations relative to the AM build directions. The linear shock and particle velocity relation for the structures with collinear build geometry shows directional differences, with the build direction exhibiting the highest slope and the filament print direction having the shallowest slope. Composites with log-cabin geometry, due to their slightly lower porosity and smaller sized pores, show higher shock velocities than the collinear structures at the same particle velocity. Microscale directionality effects are also observed, with the pore collapse velocity dependent on the pore configuration. Specifically, the pore collapse velocity is highest for pores elongated along the impact direction which is the case for the colinear structures impacted in the filament print direction, which is consistent with the directionality trend observed in the data for the shock and particle velocity equation of state. The pore collapse velocity approaches ∼80 % of the shock velocity and is several times the average bulk particle velocity, suggesting a highly hydrodynamic mechanism of pore collapse. Overall, both the macroscale response as measured by the shock and particle velocity relationship, and the microscale response as measured by the pore collapse velocity, are found to be anisotropic and dependent on the AM composite structure.

Wagner, K. B. [Georgia Institute of Technology, At↗

Highly oriented carbon fiber–polymer composites via additive manufacturing

Additive manufacturing, diverging from traditional manufacturing techniques, such as casting and machining materials, can handle complex shapes with great design flexibility without the typical waste. Although this technique has been mainly used for rapid prototyping, interest is growing in using this method to directly manufacture actual parts of complex shape. To use 3D-printing additive manufacturing in wide spread applications, the technique and the feedstock materials require improvements to meet the mechanical requirements of load-bearing components. Thus, we investigated the short fiber (0.2 mm to 0.4 mm) reinforced acrylonitrile-butadiene-styrene composites as a feedstock for 3D-printing in terms of their processibility, microstructure and mechanical performance; and also provided comparison with traditional compression molded composites. The tensile strength and modulus of 3D-printed samples increased ~115% and ~700%, respectively. 3D-printer yielded samples with very high fiber orientation in printing direction (up to 91.5 %), whereas, compression molding process yielded samples with significantly less fiber orientation. Microstructure-mechanical property relationships revealed that although the relatively high porosity is observed in the 3D-printed composites as compared to those produced by the conventional compression molding technique, they both exhibited comparable tensile strength and modulus. Furthermore, this phenomena is explained based on the changes in fiber orientation, dispersion and void formation.

36 MATERIALS SCIENCE↗

Imaging Carbon Nanotubes in High Performance Polymer Composites via Magnetic Force Microscope

Application of carbon nanotubes as reinforcement in structural composites is dependent on the efficient dispersion of the nanotubes in a high performance polymer matrix. The characterization of such dispersion is limited by the lack of available tools to visualize the quality of the matrix/carbon nanotube interaction. The work reported herein demonstrates the use of magnetic force microscopy (MFM) as a promising technique for characterizing the dispersion of nanotubes in a high performance polymer matrix.

Lillehei, Peter T.↗

Fused filament fabrication of polymer composites for extreme environments

Vast improvements have been made to the capabilities of advanced manufacturing (AM), yet there are still limitations on which materials can effectively be used in the technology. To this end, parts created using AM would benefit from the ability to be developed from feedstock materials incorporating additional functionality. A common three-dimensional (3D) printing polymer, acrylonitrile butadiene styrene, was combined with bismuth and polyvinylidene fluoride via a solvent treatment to fabricate multifunctional composite materials for AM. Composites of varying weight percent loadings were extruded into filaments, which were subsequently 3D printed into blocks via fused filament fabrication. Investigating the material properties demonstrated that in addition to the printed blocks successfully performing as radiation shields, the chemical, thermal, and mechanical properties are suitable for AM. Thus, this work demonstrates that it is possible to enhance AM components with augmented capabilities while not significantly altering the material properties which make AM possible.

36 MATERIALS SCIENCE↗

Radio-Wave Absorbing Properties of Polymer Composites on the Basis of Shungite and Carbon Nanomaterial Taunit-M

Nanocomposite painting and varnishing materials on the basis of carbon nanomaterials and organic polymers can be used to create microwave protective coatings. Such coatings show thermo-, chemo-, plasma-, and radiation-resistant properties. Largely, these properties are determined by the concentration of carbon nanomaterials in composites. Moreover, different nanomaterials in such coatings show fundamentally different concentration dependences of the electrical conductivity.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Characterizing SWCNT Dispersion in Polymer Composites

The new wave of single wall carbon nanotube (SWCNT) infused composites will yield structurally sound multifunctional nanomaterials. The SWCNT network requires thorough dispersion within the polymer matrix in order to maximize the benefits of the nanomaterial. However, before any nanomaterials can be used in aerospace applications a means of quality assurance and quality control must be certified. Quality control certification requires a means of quantification, however, the measurement protocol mandates a method of seeing the dispersion first. We describe here the new tools that we have developed and implemented to first be able to see carbon nanotubes in polymers and second to measure or quantify the dispersion of the nanotubes.

Lillehei, Peter T.↗