SEARCH · Engineering Papers

Results for “plastic behavior”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

All sources NASA NTRS DOE OSTI

DOE OSTI2023

Transition from Vogel-Fulcher-Tammann to Arrhenius Ion-Conducting Behavior in Poly(Ethyl Acrylate)-Based Solid Polymer Electrolytes via Succinonitrile Plasticizer Addition

Solid polymer electrolytes (SPEs) offer potential advantages over liquid electrolytes, including flexibility, safety, and processability. However, they suffer from low room-temperature ionic conductivity. Recently, it has been reported a poly(ethyl acrylate) based (polyEA) SPE, by incorporating 50 wt% of succinonitrile (SN) solid plasticizer, 30 wt% of lithium salt and 5 wt% of fluoroethylene carbonate additive, which achieves a high room-temperature ionic conductivity of 1.01 × 10 −3 S cm −1 (Nat. Nanotechnol, 2022, 17, 768-776). This novel SPE exhibits stability against Li 0 and anodic stability up to 4.9 V vs Li + /Li. However, the specific mechanism responsible for its high ionic conductivity remains elusive. In this work, by adjusting the weight ratio of SN in the SPE, a transition from Vogel-Fulcher-Tammann to Arrhenius ion-conducting behavior is observed. It is demonstrated that the addition of SN leads to the gradual decoupling of Li-ion from the polymer backbone and its coordination with SN, as revealed by 6 Li solid-state nuclear magnetic resonance spectroscopy. As a result, Li-ion migration primarily occurs through SN rather than the segmental motion of the polymer backbone. Performances of the SPE in Cu||Li, Li||Li and a LiFePO 4 ||Li pouch cells are shown to demonstrate the commercial viability of this SPE in Li 0 -anode solid-state batteries.

Electrochemistry↗

DOE OSTI2025

The Role of Dislocations in the Anelasticity of the Upper Mantle

Dislocation‐based dissipation mechanisms potentially control the viscoelastic response of Earth's upper mantle across a variety of geodynamic contexts, including glacial isostatic adjustment, postseismic creep, and seismic‐wave attenuation. However, there is no consensus on which dislocation‐based, microphysical process controls the viscoelastic behavior of the upper mantle. Although both intergranular (plastic anisotropy) and intragranular (backstress) mechanisms have been proposed, there is currently insufficient laboratory data to discriminate between those mechanisms. Here, we present the results of forced‐oscillation experiments in a deformation‐DIA apparatus at confining pressures of 3–7 GPa and temperatures of 298–1370 K. Our experiments tested the viscoelastic response of polycrystalline olivine—the main constituent of the upper mantle—at stress amplitudes from 70 to 2,800 MPa. Mechanical data are complemented by microstructural analyses of grain size, crystallographic preferred orientation, and dislocation density. We observe amplitude‐ and frequency‐dependent attenuation and modulus relaxation and find that numerical solutions of the backstress model match our results well. Therefore, we argue that interactions among dislocations, rather than intergranular processes (e.g., plastic anisotropy or grain boundary sliding), control the viscoelastic behavior of polycrystalline olivine in our experiments. In addition, we present a linearized version of the constitutive equations of the backstress model and extrapolate it to conditions typical of seismic‐wave propagation in the upper mantle. Our extrapolation demonstrates that the backstress model can explain the magnitude of seismic‐wave attenuation in the upper mantle, although some modification is required to explain the weak frequency dependence of attenuation observed in nature and in previous experimental work.

Hein, Diede [Univ. of Minnesota, Minneapolis, MN (↗

NASA NTRS1982

Pressure concentrations due to plastic deformation of thin films or gaskets between anvils

Plastic deformation of either a sample or a gasket between diamond anvils leads to large pressure concentrations, i.e., the maximum pressure can be many times the average pressure. This behavior is discussed using elementary plasticity theory for the case where the pressures are sufficiently low that the yield stress can be assumed not to vary with pressure. It is then shown that the pressure concentration factor can be even much larger when the yield stress of the sample at the highest pressure is much greater than the yield stress at the lowest pressure. This is illustrated with solid xenon where it is shown that the assumption that Nelson and Ruoff made about the pressure distribution in their xenon samples is incorrect. The pressure distribution is shown to be much steeper than assumed. Thus, the pressure they observed electrical conduction in xenon was above 1 Mbar.

Chan, K. S.↗

NASA NTRS1990

Ductility enhancement from interface dislocation sources in a directionally solidified beta + gamma + gamma-prime Ni-Fe-Al composite alloy

A directionally solidified beta + gamma + gamma-prime Ni-Fe-Al in situ composite alloy of composition Ni50Fe30Al20 has been used to investigate the effect of a plastically soft second phase on the mechanical behavior of a B2 ordered intermetallic alloy. This material exhibits extensive plasticity during compressive deformation at room temperature and fails in shear with extensive gamma + gamma-prime lamellar or rod pullout. The material also exhibits about 10 percent tensile elongation to fracture at room temperature, with final fracture that includes substantial necking of the gamma + gamma-prime lamellae or rods. Observation of slip lines and dislocation substructures discloses that the normally brittle beta matrix undergoes extensive plasticity in order to deform compatibly with the more ductile gamma phase. The plasticity of the beta matrix is accomplished by the generation of glissile dislocations into the beta matrix from the beta/gamma interface region and is enhanced because of a favorable beta-gamma orientation relationship for slip transfer. Ductility enhancement from interface-generated mobile dislocations generated from beta-gamma interfaces is compared to that observed in film-coated beta-NiAl single crystals and FeAl polycrystals.

Larsen, M.↗

NASA NTRS1984

Plasticity, viscoplasticity, and creep of solids by mechanical subelement models

This paper discusses the modelling by mechanical subelements, the general plasticity, the viscoplasticity, and the creep behavior of solids under multiaxial loading conditions. The formulation of a time-independent elastic-plastic analysis is based on the viscoplasticity theory and the assumed stress finite element method. An example of an in-plane stress problem is included.

Pian, T. H. H.↗

DOE OSTI2021

Thermal-Mechanical Elastic-Plastic and Ductile Failure Model Calibrations for 6061-T651 Aluminum Alloy from Plate

Numerical simulations of metallic structures undergoing rapid loading into the plastic range require material models that accurately represent the response. In general, the material response can be seen as having four interrelated parts: the baseline response under slow loading, the effect of strain rate, the conversion of plastic work into heat and the effect of temperature. In essence, the material behaves in a thermal-mechanical manner if the loading is fast enough so when heat is generated by plastic deformation it raises the temperature and therefore influences the mechanical response. In these cases, appropriate models that can capture the aspects listed above are necessary. The matters of interest here are the elastic-plastic response and ductile failure behavior of 6061-T651 aluminum alloy under the conditions described above. The work was accomplished by first designing and conducting a material test program to provide data for the calibration of a modular $J_2$ plasticity model with isotropic hardening as well as a ductile failure model. Both included modules that accounted for temperature and strain rate dependence. The models were coupled with an adiabatic heating module to calculate the temperature rise due to the conversion of plastic work to heat. The test program included uniaxial tension tests conducted at room temperature, 150 and 300 C and at strain rates between 10 –4 and 10 3 1/s as well as four geometries of notched tension specimens and two tests on specimens with shear-dominated deformations. The test data collected allowed the calibration of both the plasticity and the ductile failure models. Most test specimens were extracted from a single piece of plate to maintain consistency. Notched tension tests came from a possibly different plate, but from the same lot. When using the model in structural finite element calculations, element formulations and sizes different from those used to model the test specimens in the calibration are likely to be used. A brief investigation demonstrated that the failure model can be particularly sensitive to the element selection and provided an initial guide to compensate in a specific example.

36 MATERIALS SCIENCE↗

NASA NTRS1987

Thermomechanical behavior of plasma-sprayed ZrO2-Y2O3 coatings influenced by plasticity, creep and oxidation

Thermocycling of ceramic-coated turbomachine components produces high thermomechanical stresses that are mitigated by plasticity and creep but aggravated by oxidation, with residual stresses exacerbated by all three. These residual stresses, coupled with the thermocyclic loading, lead to high compressive stresses that cause the coating to spall. A ceramic-coated gas path seal is modeled with consideration given to creep, plasticity, and oxidation. The resulting stresses and possible failure modes are discussed.

Padovan, J.↗

NASA NTRS1987

Thermomechanical behavior of plasma-sprayed ZrO2-Y2O3 coatings influenced by plasticity, creep, and oxidation

Padovan, J.↗

DOE OSTI2026

Computational methods in solution-based plastics purification

Plastic waste can be recycled into resins with near-virgin properties by solution-based purification processes that selectively dissolve polymers, remove contaminants, or detach printing residues. Here, in this review, we examine computational methods for predicting the behavior governing solution-based plastic purification, motivated by the vast polymer–solvent–contaminant compositional space. We discuss thermodynamic and machine learning methods for predicting polymer–solvent and polymer–contaminant interaction and review physics-based molecular dynamics simulations that resolve molecular-scale phenomena within polymer matrices inaccessible to screening methods. We highlight how these methods have informed experimental design for dissolution-based recycling and solvent-based contaminant removal. Finally, we discuss the prospective role of agentic AI in integrating these computational tools with real-time sorting data to adapt purification conditions to the compositional variability of real post-consumer feedstocks. This review charts a path toward computationally guided solution-based purification workflows that can respond to the complexity inherent in plastic waste streams.

Altamimi, Ali [Univ. of Wisconsin, Madison, WI (Un↗

DOE OSTI2020

Concentration dependent properties and plastic deformation facilitate instability of the solid-electrolyte interphase in Li-ion batteries

Lithium-ion batteries (LIBs) often suffer from capacity fading and poor cyclic performance due to mechanical degradation of the solid-electrolyte interphase (SEI). Here we perform numerical simulations and theoretical analysis to elucidate the role of plasticity in wrinkling and ratcheting behaviors of an SEI/electrode system. A coupled diffusion and finite deformation framework is formulated and numerically implemented as a user-element subroutine (UEL) to describe transient lithium diffusion and accompanying elastic–viscoplastic deformation of the electrode. It is found that concentration dependent properties and plastic deformation facilitate wrinkling in such a system. A wrinkled morphology may further lead to ratcheting and related failure under cycling. A phase diagram of four types of cyclic behaviorsis identified in terms of the charging rate and time. Our analysis suggests several potential strategies to avoid wrinkling and ratcheting instabilities, such as charging/discharging the electrode at a sufficiently slow rate, and/or introducing a thick artificial SEI with a pre-tension.

25 ENERGY STORAGE↗

NASA NTRS1986

Constitutive modeling for isotropic materials

The objective of the program is to evaluate and develop existing constitutive models for use in finite-element structural analysis of turbine engine hot section components. The class of constitutive equation studied is considered unified in that all inelastic deformation including plasticity, creep, and stress relaxation are treated in a single term rather than a classical separation of plasticity (time independent) and creep (time dependent) behavior. The unified theories employed also do not utilize the classical yield surface or plastic potential concept. The models are constructed from an appropriate flow law, a scalar kinetic relation between strain rate, temperature and stress, and evolutionary equations for internal variables describing strain or work hardening, both isotropic and directional (kinematic). This and other studies have shown that the unified approach is particularly suited for determining the cyclic behavior of superalloy type blade and vane materials and is entirely compatible with three-dimensional inelastic finite-element formulations. The behavior was examined of a second nickel-base alloy, MAR-M247, and compared it with the Bodner-Partom model, further examined procedures for determining the material-specific constants in the models, and exercised the MARC code for a turbine blade under simulated flight spectrum loading. Results are summarized.

Lindholm, Ulric S.↗

NASA NTRS2016

Plasticity Tool for Predicting Shear Nonlinearity of Unidirectional Laminates Under Multiaxial Loading

This study implements a plasticity tool to predict the nonlinear shear behavior of unidirectional composite laminates under multiaxial loadings, with an intent to further develop the tool for use in composite progressive damage analysis. The steps for developing the plasticity tool include establishing a general quadratic yield function, deriving the incremental elasto-plastic stress-strain relations using the yield function with associated flow rule, and integrating the elasto-plastic stress-strain relations with a modified Euler method and a substepping scheme. Micromechanics analyses are performed to obtain normal and shear stress-strain curves that are used in determining the plasticity parameters of the yield function. By analyzing a micromechanics model, a virtual testing approach is used to replace costly experimental tests for obtaining stress-strain responses of composites under various loadings. The predicted elastic moduli and Poisson's ratios are in good agreement with experimental data. The substepping scheme for integrating the elasto-plastic stress-strain relations is suitable for working with displacement-based finite element codes. An illustration problem is solved to show that the plasticity tool can predict the nonlinear shear behavior for a unidirectional laminate subjected to multiaxial loadings.

Wang, John T.↗

DOE OSTI2026

Siloxane-modified polycarbosilane flexible Prepregs for fabrication of ceramic matrix composites via compression molding and PIP densification

For this work, the development of ceramic matrix composites (CMCs) using 5 harness satin carbon fiber fabric impregnated with commercial polycarbosilane precursor plasticized by siloxane copolymer was investigated aiming to improve wetting behavior and shape conformability. The polycarbosilane precursor and polysiloxane plasticizer were mixed at varying weight ratios to obtain flexible preceramic resin prepreg cloths. 13 plies of preceramic polymer prepreg cloths were stacked in 0/90° layup and cured by compression molding, followed by densified via PIP process. The CMCs were densified with eight PIP cycles followed by final crystallization at 1600 °C. The CMCs made with 10 wt% polysiloxane loading showed lower viscosity of the prepreg resin as well as higher strength and displacement to failure compared to those fabricated from unplasticized polycarbosilane prepolymer. In contrast, at higher concentration of plasticizer, viscosity of the prepreg resin increased, and the CMC became more brittle; however, it exhibited considerably higher thermal conductivity.

Carbosilane↗

DOE OSTI2022

Damage Accumulations Predictions for Boiler Components Via Microstructurally Informed Material Models

The goal of the project was to model material behavior and degradation during cyclic plasticity— with and without hold time—for nickel-based superalloys used in USC (ultra-super-critical) and A-USC (advanced-ultra-super-critical) boiler components. The study provided physically informed models, capturing the microstructural changes taking place in the industrial components under cyclic loading and long duration stress (up to 300,000 hours) and high temperature exposure (1100°F/593°C to 1400°F/760°C). The major developments were: 1) Qualitative and quantitative understanding of microstructure evolution (gamma prime precipitates), deformation (dislocation density), and damage mechanisms of Haynes ® 282 alloy. 2) Qualitative understanding of microstructural features generating local strain variations. 3) A continuum damage mechanics model (CDM) for Haynes ® 282 alloy at 1100°F to 1400°F capturing cyclic behavior with and without hold time. 4) Structural analysis for creep and LCF life predictions of an USC thick-wall Grade 91 superheater steel header and understanding life sensitivity to wall thickness of an AUSC Haynes ® 282 header.

20 FOSSIL-FUELED POWER PLANTS↗

DOE OSTI2023

Crystal plasticity model of BCC metals from large-scale MD simulations

Accurate crystal plasticity models that faithfully capture the behavior of single crystals under a wide range of loading conditions, such as loading direction, strain rate, and temperature, are still lacking. Here we introduce a novel approach in which a crystal plasticity (CP) model is informed directly from and calibrated to large-scale quantum-accurate MD simulations in which single crystal BCC Ta serves as a testbed material. By analyzing our large set of MD simulations several key insights are obtained leading us to modify constitutive assumptions in order to address deficiencies of existing CP models. Importantly, we observe that the standard notion of fixed slip systems – pairs of slip directions and slip planes – is inadequate for describing high-rate plasticity in BCC tantalum at room temperature. Instead, pencil glide defined as dislocation motion in the maximum resolved shear stress planes (MRSSP) of each Burgers vector is fully consistent with our MD simulation data while providing significant simplifications of the constitutive relations. Herein, our resulting new CP model closely matches the behavior of single crystals observed in high-rate MD simulations while being fully consistent with lower rate experimental results.

36 MATERIALS SCIENCE↗

NASA NTRS1949

Plastic buckling of a rectangular plate under edge thrusts

The fundamental equations for the plastic buckling of a rectangular plate under edge thrusts are developed on the basis of a new set of stress-strain relations for the behavior of a metal in the plastic range. These relations are derived for buckling from a state of uniform compression. The fundamental equation for the buckling of a simply compressed plate together with typical boundary conditions is then developed and the results are applied to calculating the buckling loads of a thin strip, a simply supported plate, and a cruciform section. Comparisons with the theories of Timoshenko and Ilyushin are made. Finally, an energy method is given which can be used for finding approximate values of the critical load.

Handelman, G H↗

DOE OSTI2020

Intrinsic size dependent plasticity in BCC micro-pillars under uniaxial tension and pure torsion

The mechanical behavior of submicron body-centered cubic (BCC) micro-pillars is investigated by three-dimensional dislocation dynamics (DD) simulations to better understand the governing mechanisms for size dependent plasticity under uniaxial tension and pure torsion. A formula is developed to compute the incremental plastic twist due to dislocation motion in DD simulations. The DD simulations show that different dislocation microstructures are created depending on the loading conditions, which leads to different size dependent mechanical behavior. While in tension plasticity is mainly governed by the kinetics of dislocation motion controlled partly by the surface dislocation sources, plastic flow in torsion is controlled by dislocation pile-ups associated with strain gradients. The simulation results also reveal a Bauschinger effect and plastic recovery under cyclic twist, which have been observed in recent experiments.

36 MATERIALS SCIENCE↗

DOE OSTI2024

A non-isothermal breakage-damage model for plastic-bonded granular materials incorporating temperature, pressure, and rate dependencies

Plastic-bonded granular materials (PBM) are widely used in industrial sectors, including building construction, abrasive applications, and defense applications such as plastic-bonded explosives. The mechanical behavior of PBM is highly nonlinear, irreversible, rate dependent, and temperature sensitive governed by various micromechanical attributions such as grain crushing and binder damage. This paper presents a thermodynamically consistent, microstructure-informed constitutive model to capture these characteristic behaviors of PBM. Key features of the model include a breakage internal variable to upscale the grain-scale information to the continuum level and to predict grain size evolution under mechanical loading. In addition, a damage internal state variable is introduced to account for the damage, deterioration, and debonding of the binder matrix upon loading. Temperature is taken as a fundamental external state variable to handle non-isothermal loading paths. The proposed model is able to capture with good accuracy several important aspects of the mechanical properties of PBM, such as pressure-dependent elasticity, pressure-dependent yield strength, brittle-to-ductile transition, temperature dependency, and rate dependency in the post-yielding regime. Furthermore, the model is validated against multiple published datasets obtained from confined and unconfined compression tests, covering various PBM compositions, confining pressures, temperatures, and strain rates.

Breakage↗