Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “pilot model”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

Practical guidance for the design of controls and displays for single pilot IFR

This paper represents a first step in developing the criteria for pilot interaction with advanced controls and displays in a single pilot IFR (SPIFR) environment. The research program presented is comprised of an analytical phase and an experimental phase. The analytical phase consisted of a review of fundamental considerations for pilot workload taking into account existing data, and using that data to develop a SPIFR pilot workload model. The rationale behind developing such a model was based on the concept that it is necessary to identify and quantify the most important components of pilot workload to guide the experimental phase of the research which consisted of an abbreviated flight test program. The purpose of the flight tests was to evaluate the workload associated with certain combinations of controls and displays in a flight environment. This was accommplished as a first step in building a data base for single pilot IFR controls and displays.

Hoh, R. H.↗
NASA NTRSDate not supplied

Trajectory Simulation for Air Traffic Management Employing a Multirotor Urban Air Mobility Aircraft Model

This paper describes a point-mass model of a multirotor electric vertical takeoff and landing aircraft designed to carry up to five passengers and a pilot. The model employs thrust, thrust vector angle and bank angle as controls, which are computed in part using the acceleration, heading-angle rate, and flight-path-angle rate generated by control systems in response to speed, heading angle, and flight-path angle commands. The equations of motion are integrated forward in time using the controls needed for following the desired vertical climb/descent and speed profiles, and horizontal path and cruise speed in the presence of wind to generate the flight trajectory.

trajectory simulation, urban air mobility aircraft↗
NASA NTRS1976

Evaluation of an envelope-limiting device using simulation and flight test of a remotely piloted research vehicle

The operating characteristics of a nonlinear envelope-limiting device were investigated at extreme flight conditions by using a real time digital aircraft spin simulation and flight tests of a scale model remotely piloted research vehicle. A digital mechanization of the F-15 control system, including the stall inhibiter, was used in the simulation and in the control system of the scale model. The operational characteristics of the stall inhibiter and the effects of the stall inhibiter on the spin susceptibility of the airplane were investigated.

Petersen, K. L.↗
NASA NTRS1993

Handling qualities effects of display latency

Display latency is the time delay between aircraft response and the corresponding response of the cockpit displays. Currently, there is no explicit specification for allowable display lags to ensure acceptable aircraft handling qualities in instrument flight conditions. This paper examines the handling qualities effects of display latency between 70 and 400 milliseconds for precision instrument flight tasks of the V-22 Tiltrotor aircraft. Display delay effects on the pilot control loop are analytically predicted through a second order pilot crossover model of the V-22 lateral axis, and handling qualities trends are evaluated through a series of fixed-base piloted simulation tests. The results show that the effects of display latency for flight path tracking tasks are driven by the stability characteristics of the attitude control loop. The data indicate that the loss of control damping due to latency can be simply predicted from knowledge of the aircraft's stability margins, control system lags, and required control bandwidths. Based on the relationship between attitude control damping and handling qualities ratings, latency design guidelines are presented. In addition, this paper presents a design philosophy, supported by simulation data, for using flight director display augmentation to suppress the effects of display latency for delays up to 300 milliseconds.

King, David W.↗
NASA NTRS1990

A piloted comparison of elastic and rigid blade-element rotor models using parallel processing technology

A piloted comparison of rigid and aeroelastic blade-element rotor models was conducted at the Crew Station Research and Development Facility (CSRDF) at Ames Research Center. FLIGHTLAB, a new simulation development and analysis tool, was used to implement these models in real time using parallel processing technology. Pilot comments and quantitative analysis performed both on-line and off-line confirmed that elastic degrees of freedom significantly affect perceived handling qualities. Trim comparisons show improved correlation with flight test data when elastic modes are modeled. The results demonstrate the efficiency with which the mathematical modeling sophistication of existing simulation facilities can be upgraded using parallel processing, and the importance of these upgrades to simulation fidelity.

Hill, Gary↗
NASA NTRS1997

A Theory for the Roll-Ratchet Phenomenon in High Performance Aircraft

Roll-ratchet refers to a high frequency oscillation which can occur in pilot-in-the-loop control of roll attitude in high performance aircraft. The frequencies of oscillation are typically well beyond those associated with the more familiar pilot-induced oscillation. A structural model of the human pilot which has been employed to provide a unified theory for aircraft handling qualities and pilot-induced oscillations is employed here to provide a theory for the existence of roll-ratchet. It is hypothesized and demonstrated using the structural model that the pilot's inappropriate use of vestibular acceleration feedback can cause this phenomenon, a possibility which has been discussed previously by other researchers. The possible influence of biodynamic feedback on roll ratchet is also discussed.

Hess, Ronald A.↗
NASA NTRS2017

Simulation Evaluation of Pilot Inputs for Real Time Modeling During Commercial Flight Operations

Aircraft dynamics characteristics can only be identified from flight data when the aircraft dynamics are excited sufficiently. A preliminary study was conducted into what types and levels of manual piloted control excitation would be required for accurate Real-Time Parameter IDentification (RTPID) results by commercial airline pilots. This includes assessing the practicality for the pilot to provide this excitation when cued, and to further understand if pilot inputs during various phases of flight provide sufficient excitation naturally. An operationally representative task was evaluated by 5 commercial airline pilots using the NASA Ice Contamination Effects Flight Training Device (ICEFTD). Results showed that it is practical to use manual pilot inputs only as a means of achieving good RTPID in all phases of flight and in flight turbulence conditions. All pilots were effective in satisfying excitation requirements when cued. Much of the time, cueing was not even necessary, as just performing the required task provided enough excitation for accurate RTPID estimation. Pilot opinion surveys reported that the additional control inputs required when prompted by the excitation cueing were easy to make, quickly mastered, and required minimal training.

Martos, Borja↗
DOE OSTI2017

A Geostatistical Study in Support of CO 2 Storage in Deep Saline Aquifers of the Shenhua CCS Project, Ordos Basin, China

The Shenhua Carbon Capture and Storage (CCS) project at the Shenbei Slope injection site in North Yulin is the first 100,000 ton-per-year scale CCS pilot project in China with an injection operation lasting nearly 3 years. In this study, we investigate various geostatistical methods and their impact on the respective geologic models on which simulation is performed to understand the phenomena observed during 3 years of Shenhua CCS operations. Although there was a brief period of wellhead pressure increase at the injection well, it unexpectedly dropped for most of the time. Another interesting observation showed that the majority of CO 2 gas injection was received by the topmost sandstone Liujiagou formation instead of the basement limestone Majiagou formation, which was predicted to have much more injectivity and storage capacity. Based on the current geostatistical methods and available data, 3 steps of reservoir modeling and flow simulation are carried out and they go from having homogeneous property models to incorporating standard 2-point geostatistical methods to using object-based models. The layer-cake models generate a rather uniform plume shape and increased pressure response. Meanwhile, two-point statistical models add more complexity to the size and shape of CO 2 plume, however are not capable of reproducing the pressure decline behavior. These results demonstrate homogeneous and 2-point geostatistical models are inadequate in interpreting subsurface heterogeneity, both due to their method and data limitations. Further work is being done with object-based models to produce a system of meandering rivers based on the geological concept of Shenhua injection site. This will help offset the data limitation and bring our model closer to geologic reality.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS2006

Free-jet Testing of a REST Scramjet at Off-Design Conditions

Scramjet flowpaths employing elliptical combustors have the potential to improve structural efficiency and performance relative to those using planar geometries. NASA Langley has developed a scramjet flowpath integrated into a lifting body vehicle, while transitioning from a rectangular capture area to both an elliptical throat and combustor. This Rectangular-to-Elliptical Shape Transition (REST) scramjet, has a design point of Mach 7.1, and is intended to operate with fixed-geometry between Mach 4.5 and 8.0. This paper describes initial free-jet testing of the heat-sink REST scramjet engine model at conditions simulating Mach 5.3 flight. Combustion of gaseous hydrogen fuel at equivalence ratios between 0.5 and 1.5 generated robust performance after ignition with a silane-hydrogen pilot. Facility model interactions were experienced for fuel equivalence ratios above 1.1, yet despite this, the flowpath was not unstarted by fuel addition at the Mach 5.3 test condition. Combustion tests at reduced stagnation enthalpy indicated that the engine self-started following termination of the fuel injection. Engine data is presented for the largest fuel equivalence ratio tested without facility interaction. These results indicate that this class of three-dimensional scramjet engine operates successfully at off-design conditions.

Smart, Michael K.↗
NASA NTRSDate not supplied

Detect-and-Avoid Maneuver Planning: Benefits of Including Route Recapture

Development of Detect-and-avoid (DAA) systems’ maneuver guidance requirements at RTCA has centered on tactical maneuvers away from the intruder. Recapturing the flight-plan route the initial maneuver is not directly taken into account by most DAA maneuver guidance algorithms. This work demonstrates potential challenges and inefficiencies that can arise in recapturing the route after resolving a conflict. Horizontal resolution trajectories for a test matrix of encounters with varying aircraft speeds and geometries are computed by minimizing either flight time or deviation to serve as a baseline. Turn directions computed from a reference DAA algorithm coupled with a pilot selection model and a second algorithm called Autoresolver (AR) are compared to these baseline resolution trajectories. Baseline results show that turning into the intruder yields favorable cost for most encounters. Additional analysis of pilot response data shows that only three-fourths of pilots’ horizontal maneuvers turn into intruders, a percentage much lower than the baseline results. Improvement to a DAA guidance algorithm based on findings in this work is discussed.

Route Recapture↗
NASA NTRSDate not supplied

Detect-and-Avoid Maneuver Planning: Benefits of Including Route Recapture

Development of Detect-and-avoid (DAA) systems’ maneuver guidance requirements at RTCA has centered on tactical maneuvers away from the intruder. Recapturing the flight-plan route the initial maneuver is not directly taken into account by most DAA maneuver guidance algorithms. This work demonstrates potential challenges and inefficiencies that can arise in recapturing the route after resolving a conflict. Horizontal resolution trajectories for a test matrix of encounters with varying aircraft speeds and geometries are computed by minimizing either flight time or deviation to serve as a baseline. Turn directions computed from a reference DAA algorithm coupled with a pilot selection model and a second algorithm called Autoresolver (AR) are compared to these baseline resolution trajectories. Baseline results show that turning into the intruder yields favorable cost for most encounters. Additional analysis of pilot response data shows that only three-fourths of pilots’ horizontal maneuvers turn into intruders, a percentage much lower than the baseline results. Improvement to a DAA guidance algorithm based on findings in this work is discussed.

Route Recapture↗
NASA NTRS1994

Extended cooperative control synthesis

This paper reports on research for extending the Cooperative Control Synthesis methodology to include a more accurate modeling of the pilot's controller dynamics. Cooperative Control Synthesis (CCS) is a methodology that addresses the problem of how to design control laws for piloted, high-order, multivariate systems and/or non-conventional dynamic configurations in the absence of flying qualities specifications. This is accomplished by emphasizing the parallel structure inherent in any pilot-controlled, augmented vehicle. The original CCS methodology is extended to include the Modified Optimal Control Model (MOCM), which is based upon the optimal control model of the human operator developed by Kleinman, Baron, and Levison in 1970. This model provides a modeling of the pilot's compensation dynamics that is more accurate than the simplified pilot dynamic representation currently in the CCS methodology. Inclusion of the MOCM into the CCS also enables the modeling of pilot-observation perception thresholds and pilot-observation attention allocation affects. This Extended Cooperative Control Synthesis (ECCS) allows for the direct calculation of pilot and system open- and closed-loop transfer functions in pole/zero form and is readily implemented in current software capable of analysis and design for dynamic systems. Example results based upon synthesizing an augmentation control law for an acceleration command system in a compensatory tracking task using the ECCS are compared with a similar synthesis performed by using the original CCS methodology. The ECCS is shown to provide augmentation control laws that yield more favorable, predicted closed-loop flying qualities and tracking performance than those synthesized using the original CCS methodology.

Davidson, John B.↗
NASA NTRS1976

Summary of flight tests to determine the spin and controllability characteristics of a remotely piloted, large-scale (3/8) fighter airplane model

An unpowered, large, dynamically scaled airplane model was test flown by remote pilot to investigate the stability and controllability of the configuration at high angles of attack. The configuration proved to be departure/spin resistant; however, spins were obtained by using techniques developed on a flight support simulator. Spin modes at high and medium high angles of attack were identified, and recovery techniques were investigated. A flight support simulation of the airplane model mechanized with low speed wind tunnel data over an angle of attack range of + or - 90 deg. and an angle of sideslip range of + or - 40 deg. provided insight into the effects of altitude, stability, aerodynamic damping, and the operation of the augmented flight control system on spins. Aerodynamic derivatives determined from flight maneuvers were used to correlate model controllability with two proposed departure/spin design criteria.

Holleman, E. C.↗
NASA NTRS1981

Comparison of closed loop model with flight test results

An analytic technique capable of predicting the landing characteristics of proposed aircraft configurations in the early stages of design was developed. In this analysis, a linear pilot-aircraft closed loop model was evaluated using experimental data generated with the NT-33 variable stability in-flight simulator. The pilot dynamics are modeled as inner and outer servo loop closures around aircraft pitch attitude, and altitude rate-of-change respectively. The landing flare maneuver is of particular interest as recent experience with military and other highly augmented vehicles shows this task to be relatively demanding, and potentially a critical design point. A unique feature of the pilot model is the incorporation of an internal model of the pilot's desired flight path for the flare maneuver.

George, F. L.↗
NASA NTRS2013

A Model of Manual Control with Perspective Scene Viewing

A model of manual control during perspective scene viewing is presented, which combines the Crossover Model with a simpli ed model of perspective-scene viewing and visual- cue selection. The model is developed for a particular example task: an idealized constant- altitude task in which the operator controls longitudinal position in the presence of both longitudinal and pitch disturbances. An experiment is performed to develop and vali- date the model. The model corresponds closely with the experimental measurements, and identi ed model parameters are highly consistent with the visual cues available in the perspective scene. The modeling results indicate that operators used one visual cue for position control, and another visual cue for velocity control (lead generation). Additionally, operators responded more quickly to rotation (pitch) than translation (longitudinal).

pilot modeling↗
NASA NTRS2017

A Dose of Reality: Radiation Analysis for Realistic Human Spacecraft

INTRODUCTION As with most computational analyses, a tradeoff exists between problem complexity, resource availability and response accuracy when modeling radiation transport from the source to a detector. The largest amount of analyst time for setting up an analysis is often spent ensuring that any simplifications made have minimal impact on the results. The vehicle shield geometry of interest is typically simplified from the original CAD design in order to reduce computation time, but this simplification requires the analyst to "re-draw" the geometry with a limited set of volumes in order to accommodate a specific radiation transport software package. The resulting low-fidelity geometry model cannot be shared with or compared to other radiation transport software packages, and the process can be error prone with increased model complexity. The work presented here demonstrates the use of the DAGMC (Direct Accelerated Geometry for Monte Carlo) Toolkit from the University of Wisconsin, to model the impacts of several space radiation sources on a CAD drawing of the US Lab module. METHODS The DAGMC toolkit workflow begins with the export of an existing CAD geometry from the native CAD to the ACIS format. The ACIS format file is then cleaned using SpaceClaim to remove small holes and component overlaps. Metadata is then assigned to the cleaned geometry file using CUBIT/Trelis from csimsoft (Registered Trademark). The DAGMC plugin script removes duplicate shared surfaces, facets the geometry to a specified tolerance, and ensures that the faceted geometry is water tight. This step also writes the material and scoring information to a standard input file format that the analyst can alter as desired prior to running the radiation transport program. The scoring results can be transformed, via python script, into a 3D format that is viewable in a standard graphics program. RESULTS The CAD model of the US Lab module of the International Space Station, inclusive of all the racks and components, was simplified to remove holes and volume overlaps. Problematic features within the drawing were also removed or repaired to prevent runtime issues. The cleaned drawing was then run through the DAGMC workflow to prepare for analysis. Pilot tests modeling transport of 1GeV proton and 800MeV/A oxygen sources show that reasonable results are converged upon in an acceptable amount of overall computation time from drawing preparation to data analysis. The FLUKA radiation transport code will next be used to model both a GCR and a trapped radiation source. These results will then be compared with measurements that have been made by the radiation instrumentation deployed inside the US Lab module. DISCUSSION Early analyses have indicated that the DAGMC workflow is a promising toolkit for running vehicle geometries of interest to NASA through multiple radiation transport codes. In addition, recent work has shown that a realistic human phantom, provided via a subcontract with the University of Florida, can be placed inside any vehicle geometry for a combinatorial analysis. This added functionality gives the user the ability to score various parameters at the organ level, and the results can then be used as input for cancer risk models.

Barzilla, J. E.↗
DOE OSTI2023

Modeling the First Hydrogen Direct Reduction Pilot Reactor for Ironmaking in the USA Using Finite Element Analysis and Its Validation Using Pilot Plant Trial Data

Direct reduction of hematite pellets with hydrogen (H 2 ) was used to produce directly reduced iron (DRI) in a pilot scale reactor at a pellet feed rate of 21.4 kg/h. At a steady state, operational parameters of the pilot plant (gas recycling rate and inlet temperature) along with key reactor output parameters, the pellet metallization, and the internal temperature profile of the reactor were reported for two scenarios with high recycle and low recycle rate of H 2 . Scenario 1, with a high recycle rate of 400 L/min H 2 along with external heating of 870 °C, gave an average metallization of 91.8%, while Scenario 2, with low recycle rate of 100 L/min H 2 and external heating of 850 °C gave a metallization of 67.8% due to the higher moles of H 2 available for reduction and the external energy required for the endothermic reduction reaction in Scenario 1 as compared with Scenario 2. Finite element analysis was used to build a model of the shaft reactor, which was validated against the metallization and internal temperature profile data. The average metallization values predicted by the model were very close to the metallization values obtained from the pilot plant samples, with 90.9% average metallization for Scenario 1 and 65.6% average metallization for Scenario 2. The internal temperature profiles in the lower region of the reactor obtained from the model were very close to these pilot plant data, with a maximum difference of 52.7 °C and 67.6 °C for Scenarios 1 and 2, respectively. The pilot plant reactor model was used extensively in the commissioning of the pilot plant and to predict the startup outcomes for a given set of operating parameters.

08 HYDROGEN↗
NASA NTRS1980

Analytical methodology for determination of helicopter IFR precision approach requirements

A systematic analytical approach to the determination of helicopter IFR precision approach requirements is formulated. The approach is based upon the hypothesis that pilot acceptance level or opinion rating of a given system is inversely related to the degree of pilot involvement in the control task. A nonlinear simulation of the helicopter approach to landing task incorporating appropriate models for UH-1H aircraft, the environmental disturbances and the human pilot was developed as a tool for evaluating the pilot acceptance hypothesis. The simulated pilot model is generic in nature and includes analytical representation of the human information acquisition, processing, and control strategies. Simulation analyses in the flight director mode indicate that the pilot model used is reasonable. Results of the simulation are used to identify candidate pilot workload metrics and to test the well known performance-work-load relationship. A pilot acceptance analytical methodology is formulated as a basis for further investigation, development and validation.

Phatak, A. V.↗