SEARCH · Engineering Papers

Results for “particle delays”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

All sources NASA NTRS DOE OSTI

DOE OSTI2026

Low-Rate Cycling Regeneration Sustains NMC811–Graphite Battery Performance through Extreme Ultrafast Charging

Urban air mobility (UAM) systems, such as electric vertical takeoff and landing (eVTOL) aircraft, require batteries capable of extreme ultrafast charging to support high-frequency operations. Here, in this work, we evaluate the electrochemical stability of NMC811–graphite full cells using a complex mixed-modal protocol designed to simulate the aggressive turnaround demands of UAM missions. We demonstrate that incorporating a periodic low-rate (0.3C) “regeneration” cycle enables cells to maintain 96% capacity retention over 900 cycles, despite repeated exposure to ultrafast pulses. To validate the efficacy of this regeneration mechanism, we performed simplified control experiments comparing continuous 10C charging against a 10C–0.3C interleaved protocol. Advanced characterization reveals that while mechanical particle fracture is pervasive at these rates, the regeneration cycles decelerate the electrochemical degradation by resolving spatially heterogeneous Ni oxidation states and relaxing lithium-ion concentration gradients. These findings provide a vital mechanistic framework for battery operation, proving that restorative charging can effectively delay and mitigate failure in demanding UAM applications.

batteries↗

NASA NTRS1998

Surface Area, and Oxidation Effects on Nitridation Kinetics of Silicon Powder Compacts

Commercially available silicon powders were wet-attrition-milled from 2 to 48 hr to achieve surface areas (SA's) ranging from 1.3 to 70 sq m/g. The surface area effects on the nitridation kinetics of silicon powder compacts were determined at 1250 or 1350 C for 4 hr. In addition, the influence of nitridation environment, and preoxidation on nitridation kinetics of a silicon powder of high surface area (approximately equals 63 sq m/g) was investigated. As the surface area increased, so did the percentage nitridation after 4 hr in N2 at 1250 or 1350 C. Silicon powders of high surface area (greater than 40 sq m/g) can be nitrided to greater than 70% at 1250 C in 4 hr. The nitridation kinetics of the high-surface-area powder compacts were significantly delayed by preoxidation treatment. Conversely, the nitridation environment had no significant influence on the nitridation kinetics of the same powder. Impurities present in the starting powder, and those accumulated during attrition milling, appeared to react with the silica layer on the surface of silicon particles to form a molten silicate layer, which provided a path for rapid diffusion of nitrogen and enhanced the nitridation kinetics of high surface area silicon powder.

Bhatt, R. T.↗

NASA NTRS2011

Technology Development to Support Human Health and Performance in Exploration Beyond Low Earth Orbit

In the course of defining the level of risks and mitigating the risks for exploration missions beyond low Earth orbit, NASA s Human Research Program (HRP) has identified the need for technology development in several areas. Long duration missions increase the risk of serious medical conditions due to limited options for return to Earth; no resupply; highly limited mass, power, volume; and communication delays. New space flight compatible medical capabilities required include: diagnostic imaging, oxygen concentrator, ventilator, laboratory analysis (saliva, blood, urine), kidney stone diagnosis & treatment, IV solution preparation and delivery. Maintenance of behavioral health in such an isolated, confined and extreme environment requires new sensory stimulation (e.g., virtual reality) technology. Unobtrusive monitoring of behavioral health and treatment methods are also required. Prolonged exposure to weightlessness deconditions bone, muscle, and the cardiovascular system. Novel exercise equipment or artificial gravity are necessary to prevent deconditioning. Monitoring of the degree of deconditioning is required to ensure that countermeasures are effective. New technologies are required in all the habitable volumes (e.g., suit, capsule, habitat, exploration vehicle, lander) to provide an adequate food system, and to meet human environmental standards for air, water, and surface contamination. Communication delays require the crew to be more autonomous. Onboard decision support tools that assist crew with real-time detection and diagnosis of vehicle and habitat operational anomalies will enable greater autonomy. Multi-use shield systems are required to provide shielding from solar particle events. The HRP is pursuing the development of these technologies in laboratories, flight analog environments and the ISS so that the human health and performance risks will be acceptable with the available resources.

Kundrot, C.E.↗

DOE OSTI2023

Effect of coherent edge-localized mode on transition to high-performance hybrid scenarios in KSTAR

This paper deals with one of the origins and trigger mechanisms responsible for the observed performance enhancements in the hybrid scenario experiments conducted in Korea Superconducting Tokamak Advanced Research (KSTAR). The major contribution to the performance improvement comes from a broader and higher pedestal formation. The increase of fast ion pressure due to a plasma density decrease also contributes substantially to the global beta. Although the reduced core plasma volume resulting from the pedestal expansion has a negative effect on the core thermal energy, a considerable confinement improvement observed in the inner core region limits the degradation. The one significant characteristic of high-performance discharges is the presence of Coherent Edge-localized Mode (CEM) activity. CEM is triggered during the pedestal recovery phase between typical ELM crashes and has been found to be related to the increase of particle and heat transport. It appears to underlie two commonly observed phenomena in high-performance hybrid scenario discharges in KSTAR; pedestal broadening and continuous density decrease. Despite the associated transport increase, CEM activities can induce performance enhancement. With the pedestal broadening, ELM crashes become delayed and weakened, which, in turn, allows for a higher pedestal. Moreover, the density decrease directly increases fast ion pressure by extending the beam-slowing-down time. The linear gyrokinetic analysis reveals that the increase of fast ions could initiate positive feedback loops, leading to the stabilization of Ion Temperature Gradient mode in the inner core region.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2025

Individual neutrino masses from a supernova

A nearby supernova will carry an unprecedented wealth of information about astrophysics, nuclear physics, and particle physics. Because supernova are fundamentally neutrino driven phenomenon, our knowledge about neutrinos—particles that remain quite elusive—will increase dramatically with such a detection. One of the biggest open questions in particle physics is related to the masses of neutrinos. Here, we show how a galactic supernova provides information about the masses of each of the three mass eigenstates , at some precision, and is well probed at JUNO. This information comes from several effects including time delay and the Mikheyev-Smirnov-Wolfenstein effect within the supernova. The time delay feature is strongest during a sharp change in the flux such as the neutronization burst; additional information may also come from a QCD phase transition in the supernova or if the supernova forms a black hole. We consider both standard cases as dictated by local oscillation experiments as well as new physics motivated scenarios where neutrino masses may differ across the galaxy. Published by the American Physical Society 2025

79 ASTRONOMY AND ASTROPHYSICS↗

NASA NTRS1992

Toward the optimization of control of unsteady separation

Regardless of our understanding of the complicated physical process, means can always be found to alter the occurrence and development of unsteady separation. To be able to optimize the control of separation, however, requires the identification of the critical aspects to which the intervention may be focused and achieve the desired result with minimum waste of effort. The Lagrangian analysis of unsteady boundary-layer traces the trajectories of individual fluid particles and reveals the 'bad seeds' that, through extreme deformation in the direction normal to the wall, eventually develop into a virtual barrier and cause the ejection of boundary-layer material into the main stream. It follows logically that separation can be triggered or delayed most effectively by targeting these 'bad seeds.' Since they are normally interior points of the boundary layer, attempts to influence them through the boundary conditions are necessarily indirect. Furthermore, as the strategy has to be the modification of the growing process of the 'bad seeds,' whatever may be the intervention scheme, it needs to be strong enough and early enough. In Shen and Wu, examples of how acceleration/deceleration of the two dimensional body, as well as the moving wall of a rotating cylinder, may affect the development of the bad seed toward separation are shown. In fact it was mentioned therein that the results might be the first step for a feasibility study of the control of unsteady separation. Presented are additional results of applying suction to an impulsively started circular cylinder.

Shen, S. F.↗

NASA NTRS2000

Calibrating Atmospheric Delay for the Cassini Gravitational Wave Experiment

The Cassini spacecraft together with one of the stations of the Deep Space Network (DSN) have been instrumented to carry out extremely precise Doppler tracking that will be used to search for the direct evidence of Gravitational radiation passing through our solar system. The two-way communications link between the ground antenna and the spacecraft constitute an "antenna" for gravitational waves that would perturb the phase of the RF signal in the link. The experiments will be carried out during the long cruise phase of the spacecraft on its journey to Saturn and will be sensitive to gravitational wave perturbations larger than the noise level fluctuations of 3 x 10(exp -15) as measured in the Allan Standard Deviation domain. The use of simultaneous, coherent X- and Ka-Band up and down signals will reduce the errors associated with charged particle fluctuations in the interplanetary medium and Earth's ionosphere to a negligible level. The primary fluctuations in the phase of the signals both to and from the spacecraft are expected to be caused by fluctuations in water vapor in the Earth's atmosphere We have designed and are testing a new atmospheric calibration system (with duplicate components) to sense line-of-sight water vapor and its physical temperature with a goal of calibrating 95% or more of tropospheric path delay fluctuations during the Cassini Gravitational Wave Experiment (GWE). The critical component of the calibration system consists of a newly designed water vapor radiometer having a I degree sensing beamwidth and 0.01 K brightness temperature stability over hour time scales. Auxiliary instrumentation includes a microwave temperature profiler to retrieve the vertical distribution of the vapor physical temperature, and surface meteorology. A detailed error budget has been developed to account for all of the possible sources of error during calibration of the GWE and will be discussed. Two identical calibration systems have been constructed in order to provide capability as well as backup during the actual GWE experiment. We will report on side-by-side testing of the vapor and temperature sensing components of this calibrations system as well as a comparison with a short baseline radio interferometric measurement at our Goldstone complex.

Resch, G. M.↗

NASA NTRS2019

Astrophysics and Technical Study of a Solar Neutrino Spacecraft: NIAC (NASA Innovative Advanced Concepts) Grant - NASA 2018-Phase-1

We report on our study of the design of a neutrino detector, shielding and veto array needed to operate a neutrino detector in space close to the Sun. This study also took into account the expected rates of Galactic gamma and cosmic rays in addition to the particles from the Sun.These preliminary studies show that we can devise a detector such that a small signal of neutrino interactions can be extracted from a large random number of events from the background sources using a double timing method from the conversion electron produced in the neutrino interaction and a secondary delayed signal from the nuclear excited state produced from the initial neutrino interaction; in our case the conversion of Ga 69 or 71 into Ge 69 or 71, but this method could apply to other nuclei with large neutrino cross sections such as Ir 115. Although these types of events need to be above 0.405 megaelectronvolt (MeV) neutrino energy and are only 66 percent of all conversion neutrino interactions on Gallium, this is a small price to pay for an increase of 10,000 by going close to the Sun to enhance the neutrino rate over the background combatorical fake-signal events. The conclusion of this Phase-1 study is very positive in that we can get the backgrounds less than 20 percent fake signals, and in addition to this we have devised another shielding method that makes the Galactic gamma-ray rate a hundred fold less which will make further improvements over these initial estimates. Although these studies are very encouraging it suggests that the next step is a NIAC Phase-II to actually build a test device,measuring basic principles such as light attention within the scintillator with high dopants and to take data in the lab with a cosmic-ray test stand and triggered X-ray source for comparison with simulated expected performance of the detector. This would be the perfect lead into a future proposal beyond a NIAC (NASA Innovative Advanced Concepts) Phase-II for a test flight of a small one-pint detector in orbit of the detector concept beyond Earth outside of the radiation belts.

Astrophysics↗

DOE OSTI2022

Silicon alloying enhances fast heating rate combustion of aluminum particles

Alloys and composites of aluminum (Al) have shown promise in regulating and enhancing particle combustion for energy generation applications. Recent work on aluminum-silicon (Al-Si) spherical alloy particles has shown improved combustion at low heating rates through enhanced diffusion accompanying a lower melting temperature. This study extends reactivity analysis to higher heating rates, comparing oxidation of Al-Si with Al. Flame speeds of Al-Si powder mixed with molybdenum trioxide (MoO 3 ) powder (Al-Si+MoO 3 ) exhibited a faster transition to steady propagation relative to Al+MoO 3 . Bomb calorimetry experiments revealed up to 5.8% greater early temperature rise for Al-Si powder. Rapid steady propagation for Al-Si mixture and faster temperature rise for Al-Si particles were attributed to accelerated kinetics evidenced in thermal equilibrium analysis of the mixtures using a differential scanning calorimeter (DSC). Larger DSC exotherms in the early stages of oxidation (i.e., 480–720 °C) correlated with early heat release and promoted steady flame propagation for Al-Si+MoO 3 compared with Al+MoO 3 . Furthermore, in multiple heating rate DSC studies, Al-Si+MoO 3 ignited at a lower heating rate (i.e., 15 ⁰C/min) than Al+MoO 3 (i.e., 20 ⁰C/min). Both mixtures ignited at temperatures less than 625 °C which is above the melting temperature of Al-Si (574 °C) and below Al (659 °C). Thus, alloy particle fuels with enhanced diffusion-controlled kinetics promote steady flame propagation and show promise for energy generation applications. This is especially promising for technologies driven by enhanced condensed phase combustion such as some propellant additives or applications dependent on reliable burn rates such as pyrotechnic time delay formulations and primers.

36 MATERIALS SCIENCE↗

DOE OSTI2021

The Influence of Pressure on Flame-Flow Characteristics of a Reacting Jet in Crossflow

This work experimentally investigates the effects of elevated combustor pressures on the characteristics of a lean premixed reacting methane/air jet injected into a lean vitiated crossflow using a 12.7 mm axial jet. Experiments were conducted in an axially staged combustor, which implements a reacting jet in crossflow (RJIC) configuration and operates over a pressure range of 1–5 atmospheres. Simultaneous CH* chemiluminescence and particle image velocimetry (PIV) are used to study the flow field and flame behavior. The results show that the reacting jet trajectory exhibits greater penetration with elevated pressure, which is a novel finding compared to available data in the literature. However, the flame liftoff point and ignition delay time both decreased with elevated pressure, which was attributed to decreased vorticity along the flame boundary which corresponds to increased Damköhler numbers (Da). Emissions measurements confirm the NOx increase with pressure as reported in the literature for single-stage gas turbine combustors. Concurrently, emission measurements for the staged configuration show the strong NOx benefit of the RJIC system: the data prove a reduction of global outlet emission levels at elevated pressure with the axially staged configuration. Here, the axial emission reduction was attributed to the decreasing liftoff at elevated pressure levels. Hence, the research emphasizes that the flame and emission characteristics are coupled; they are not only dependent on the geometric parameters and momentum flux ratios but are also a function of pressure.

03 NATURAL GAS↗

NASA NTRS1985

DE 1 observations of Siple transmitter signals and associated sidebands

Initial results from an active wave injection experiment aimed at studying coherent VLF wave propagation and wave-particle interactions in the magnetosphere are presented. The VLF signals were injected from a transmitting facility at Siple Station, Antarctica, and were received on the high-altitude, polar-orbiting Dynamics Explorer 1 satellite. Data received by the satellite are described and measurements of the propagation delay, signal amplitude, and in situ electron densities are discussed. Ray propagation paths to the satellite for two days are discussed, and sidebands associated with Siple signals observed on one of the days are presented.

Rastani, K.↗

NASA NTRSDate not supplied

The BioSensor Instrument Beyond LEIA: a Versatile Platform for Lunar Biology

Introduction: The BioSensor is a deep-space-compatible automated microfluidic culturing instrument. While originally designed to measure the effects of deep space radiation on yeast growth for the BioSentinel mission, it has the potential to host a diverse range of life science experiments with single- and/or multi-celled organisms and can be adapted to interface with a diverse range of platforms in both crewed and uncrewed settings. It is therefore a leading candidate for hosting life sciences experimentation associated with a lunar surface habitat. BioSensor design: The function of the BioSensor is to monitor the growth and metabolic activity of samples in batch fluidic culture, without the need for crew involvement. The current configuration houses organisms in 16 wells within 16 microfluidic cards, accommodating a total of 256 samples, replicates, and controls. Each well has an optical system including three LEDs and a photodiode detector to measure absorbance at three wavelengths, enabling measurement of optical density, color change in dyes such as alamarBlue, and bioproduction of pigmented compounds. Organisms are loaded into fluidic wells and air-dried for storage during integration, launch, and transit, then activated by the introduction of culture medium from storage bags via manifolds that fill one card at a time. Temperature is controlled by individual card heaters, and timing of all activities (fluidics fills, optical measurements, temperatures) is directed by an experiment script. The self-contained BioSensor payload is roughly 4U in volume; with electrical/mechanical/thermal interface, e.g. for operation on ISS or a lunar lander, as well as a linear energy-transfer (LET) charged-particle radiation spectrometer, the entire system is closer to 6U. BioSentinel and LEIA: Flown on the ISS and in a deep-space free flyer for BioSentinel, the BioSensor has been modified for use in the LEIA mission, including improvements to reduce the sensitivity to lengthy launch delays. LEIA will monitor yeast growth in the radiation and reduced-gravity environment of the lunar surface no earlier than 2026, on a CLPS lander [4]. Changes include accommodating additional culture media and an additional LED color for a new biological assay (bioproduction of carotenoids-- dietary antioxidants), as well as modifications to the housing to allow late-load biology changeout and improved isolation between fluidics and electronics. Future prospects: Future work with the BioSensor, beyond LEIA, will include expanding the range and diversity of organisms and assays accommodated. Preliminary work has demonstrated the growth of Arabidopsis seedlings in BioSensor fluidic cards, including optical measurements of growth rate over time. Minor modifications could allow measurement of phenotypes related to photosynthetic capacity in both plants and cyanobacteria. The experimental capabilities of the BioSensor could be dramatically increased by introducing the capability for fluorescence measurements, and/or the design of novel biological assays using luminescence. The BioSensor can also be adapted for new platforms and experiment settings; in addition to free-flyer, ISS, and CLPS lander, a preliminary design concept has been developed for crewed deployment directly to the lunar surface. The instrument could be accommodated inside a lunar habitat, where its automated operation would make it an excellent candidate for experiments from fundamental investigations into the response of organisms to lunar surface conditions to applied-science purposes such as screening engineered strains of various organisms for bioproduction capability.

J A Lee↗

NASA NTRS1982

Differential spacecraft charging on the geostationary operational environmental satellites

Subsystems aboard the Geostationary Operational Environmental Satellites 4 and 5 showed instances of anomalous changes in state corresponding to false commands. Evidence linking the anomalous changes to geomagnetic activity, and presumably static discharges generated by spacecraft differential charging induced by substorm particle injection events is presented. The anomalies are shown to be correlated with individual substorms as monitored by stations of the North American Magnetometer Chain. The relative frequency of the anomalies is shown to be a function of geomagnetic activity. Finally a least squares fit to the time delay between substorm initiation and spacecraft anomaly as a function of spacecraft local time is shown to be consistent with injected electron populations with energy in the range 10 keV to 15 keV, in agreement with present understanding of the spacecraft charging mechanism. The spacecraft elements responsible for the differential charging were not satisfactorily identified. That question is currently under investigation.

Farthing, W. H.↗

DOE OSTI2024

Multispecies Ion Acceleration in 3D Magnetic Reconnection with Hybrid-Kinetic Simulations

Magnetic reconnection drives multispecies particle acceleration broadly in space and astrophysics. Here we perform the first 3D hybrid simulations (fluid electrons, kinetic ions) that contain sufficient scale separation to produce nonthermal heavy-ion acceleration, with fragmented flux ropes critical for accelerating all species. We demonstrate the acceleration of all ion species (up to Fe) into power-law spectra with similar indices, by a common Fermi acceleration mechanism. The upstream ion velocities influence the first Fermi reflection for injection. The subsequent onsets of Fermi acceleration are delayed for ions with lower charge-mass ratios (Q/M), until growing flux ropes magnetize them. This leads to a species-dependent maximum energy/nucleon ∝(Q/M) α . These findings are consistent with in situ observations in reconnection regions, suggesting Fermi acceleration as the dominant multispecies ion acceleration mechanism.

79 ASTRONOMY AND ASTROPHYSICS↗

NASA NTRS2010

Cluster in the Auroral Acceleration Region

Due to a fortuitous evolution of the Cluster orbit, the Cluster spacecraft penetrated for the first time in its mission the heart of Earth's auroral acceleration region (AAR) in December 2009 and January 2010. During this time a special AAR campaign was carried out by the various Cluster instrument teams with special support from ESA and NASA facilities. We present some of the first multi-spacecraft observations of the waves, particles and fields made during that campaign. The Cluster spacecraft configuration during these AAR passages was such that it allowed us to explore the differences in the signatures of waves, particles, and fields on the various spacecraft in ways not possible with single spacecraft. For example, one spacecraft was more poleward than the other three (C2), one was at higher altitude (C1), and one of them (0) followed another (C4) through the AAR on approximately the same track but delayed by three minutes. Their separations were generally on the order of a few thousand km or less and occasionally two of them were lying along the same magnetic field line. We will show some of the first analyses of the data obtained during the AAR campaign, where upward and downward current regions, and the waves specifically associated with those regions, as well as the auroral cavities, were observed similarly and differently on the various spacecraft, helping us to explore the spatial, as well as the temporal, aspects of processes occurring in the AAR.

Pickett, Jolene S.↗

NASA NTRSDate not supplied

Neuroimmune Responses to Space Radiation

One of the main health risks in human deep space exploration is central nervous system (CNS) damage by ionizing radiation due to exposure to galactic cosmic rays (GCRs). In animal models, irradiation with simulated GCRs or their components has been shown to cause neurodegeneration and neuroinflammation associated with cognitive and behavioral dysfunction. The extent of CNS damage is partially mediated by the blood-brain barrier (BBB), which regulates the interaction between CNS and systemic responses to stressors in the rest of the body. The main cellular regulators of BBB permeability are astrocytes, which also modulate neuronal death, neuroinflammation and oxidative stress. However, studies on BBB and astrocyte functions in regulating CNS responses to ionizing radiation have been limited, especially in human tissue/organ analogs. Therefore, we developed a high-throughput 3D organ-on-a-chip system to study human CNS and BBB impairments caused by deep space radiation. We investigated both immediate and delayed CNS responses to major GCR components: 600MeV/n 56Fe ions. We observed ionizing radiation-mediated dose-dependent increases in BBB permeability that was exacerbated by astrocyte presence and accompanied by altered cytokine expression including interleukin-1 receptor alpha downregulation, and increased oxidative stress. In particular, 600MeV/n 56Fe particle irradiation selectively increased damage and blood-brain barrier permeability only in models that contained astrocytes in addition to endothelial cells, indicating astrocytes as a particularly radiosensitive component of the CNS that could therefore be a suitable a target for neuroprotection. Future studies will compare human and mouse CNS model responses to simulated GCRs and evaluate the induction of an anti-inflammatory phenotype in astrocytes as a potential countermeasure. Furthermore, in our lab we have been exploring the individual variability, genomic associations and secreted biomarkers of responses to space radiation, which could eventually be combined to address personalized CNS health risk and develop individual countermeasures. Ultimately, we aim to expand upon these results to uncover novel cellular and mechanistic targets for countermeasure development to mitigate human CNS damage in deep space exploration.

space radiation↗

DOE OSTI2023

TEAMER - Acoustic Particle Velocity Measurements - CRADA 601 (Abstract)

With relatively few deployments of tidal turbines, the extent and effect of underwater sounds generated from these turbines is not well understood. The University of Washington (UW) is deploying a cross-flow turbine system, the Turbine Lander, in the entrance channel to Sequim Bay. The deployment of this system provides an opportunity to understand the noise radiated by the turbine and its sources. There are three hypothesized sound sources associated with operation of the turbine: 1) a continuous tone associated with energized power electronics; 2) sound associated with the generator when the turbine is rotating; and 3) sound associated with the bearing pack that supports the rotor. PNNL is collaborating with UW and Integral Consulting Inc. (Integral) to simultaneously measure sound sources using three different devices. The NoiseSpotter®, an acoustic sensor system designed by Integral, measures acoustic pressure and a three-dimensional particle velocity vector. The NoiseSpotter, along with a commercial-off-the-shelf acoustic particle motion and pressure sensor (M20-105, Geospectrum Technologies Inc.) owned by PNNL will be deployed on the seabed approximately 50-100 m from the Turbine Lander. UW will concurrently deploy Drifting Acoustic Instrumentation SYstems (DAISYs) to characterize acoustic pressure near the Turbine Lander and localize sounds using a Time Delay of Arrival (TDOA) algorithm. Integral, UW, and PNNL will collaborate on data analysis and interpretation, with the intention of jointly authoring an archival paper on the results. The noise generated from the Turbine Lander is not expected to be significant, yet this experiment will help to evaluate the efficacy of combining technologies to characterize noise and provide insights for approaches to consider for future turbine deployments at other locations.

16 TIDAL AND WAVE POWER↗

NASA NTRS1983

Characteristics of gamma-ray line flares

Observations of solar gamma rays by the Solar Maximum Mission (SMM) demonstrate that energetic protons and ions are rapidly accelerated during the impulsive phase. To understand the acceleration mechanisms for these particles, the characteristics of the gamma ray line flares observed by SMM were studied. Some very intense hard X-ray flares without detectable gamma ray lines were also investigated. Gamma ray line flares are distinguished from other flares by: (1) intense hard X-ray and microwave emissions; (2) delay of high energy hard X-rays; (3) emission of type 2 and/or type 4 radio bursts; and (4) flat hard X-ray spectra (average power law index: 3.1). The majority of the gamma ray line flares shared all these characteristics, and the remainder shared at least three of them. Positive correlations were found between durations of spike bursts and spatial sizes of flare loops as well as between delay times and durations of spike bursts.

Bai, T.↗