Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “oxide weights”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Coatings for directional eutectics

Coatings developed to provide oxidation protection for the directionally-solidified eutectic alloy NiTaC-B (4.4 weight percent Cr) were evaluated. Of seven Co-, Fe- and Ni-base coatings that were initially investigated, best resistance to cyclic oxidation was demonstrated by duplex coatings fabricated by depositing a layer of NiCrAl(Y) by vacuum evaporation from an electron beam source followed by deposition of an Al overlayer using the pack cementation process. It was found that addition of carbon to the coating alloy substantially eliminated the problem of fiber denudation in TaC-type eutectic alloys. Burner rig cycled NiTaC-B samples coated with Ni-20Cr-5Al-0.1C-0.1Y+Al and rupture-tested at 1100 deg C performed as well as or better than uncoated, vacuum cycled and air-tested NiTaC-13; however, a slight degradation with respect to uncoated material was noted in air-stress rupture tests at 870 deg C for both cycled and uncycled samples.

Rairden, J. R.↗
NASA NTRS2006

Cyclic Oxidation Behavior of Cold Sprayed CuCrAl-Coated and Uncoated GRCop-84 Substrates for Space Launch Vehicles

A newly developed Cu-23 (wt %) Cr-5%Al (CuCrAl) alloy shown to resist hydridation and oxidation in an as-cast form is currently being considered as a protective coating for GRCop-84, which is an advanced copper alloy containing 8 (at.%) Cr and 4 (at.%) Nb. The coating was deposited on GRCop-84 substrates by the cold spray deposition technique. Cyclic oxidation tests conducted in air on both coated and uncoated substrates between 773 and 1073 K revealed that the coating remained intact and protected the substrate up to 1073 K. No significant weight loss of the coated specimens were observed at 773 and 873 K even after a cumulative cyclic time of 500 h. About a 10 percent weight loss observed at 973 and 1073 K was attributed to the excessive oxidation of the uncoated sides. In contrast, the uncoated substrate lost as much as 80 percent of its original weight under similar test conditions. It is concluded that the cold sprayed CuCrAl coating is suitable for protecting GRCop-84 substrates.

Raj, S. V.↗
NASA NTRS1991

Effect of sulfur removal on Al2O3 scale adhesion

The effect of removing sulfur impurity on the adhesion of Al2O3 scale to NiCrAl was investigated in four experiments. It was found that removing sulfur to concentration less than 1 ppm per weight is sufficient to produce a very significant degree of alpha-Al2O3 scale adhesion to undoped NiCrAl alloys. Results of experiments show that repeated oxidation, and polishing after each oxidation cycle, of pure NiCrAl alloy lowered sulfur content from 10 to 2 ppm by weight (presumably by removing the segregated interfacial layer after each cycle); thinner samples became adherent after fewer oxidation-polishing cycles because of more limited supply of sulfur. It was found that spalling in subsequent cyclic oxidation tests was a direct function of the initial sulfur content. The transition between the adherent and nonadherent behavior was modeled in terms of sulfur flux, sulfur content, and sulfur segregation.

Smialek, James L.↗
NASA NTRS1954

Relation Between Roughness of Interface and Adherence of Porcelain Enamel to Steel

Porcelain-enamel ground coats were prepared and applied under conditions that gave various degrees of adherence between enamel and a low-carbon steel (enameling iron). The variations in adherence were produced by (a) varying the amount of cobalt-oxide addition in the frit, (b) varying the type of metallic-oxide addition in the frit, keeping the amount constant at 0.8 weight percent, (c) varying the surface treatment of the metal before application of the enamel, by pickling, sandblasting, and polishing, and (d) varying the time of firing of the enamel containing 0.8 percent of cobalt oxide. Specimens of each enamel were given the standard adherence test of the Porcelain Enamel Institute. Metallographic sections were made on which the roughness of interface was evaluated by counting the number of anchor points (undercuts) per centimeter of specimen length and also by measuring the length of the interface and expressing results as the ratio of this length to the length of a straight line parallel to the over-all direction of the interface.

Richmond, J C↗
NASA NTRS2011

Moisture-Induced TBC Spallation on Turbine Blade Samples

Delayed failure of TBCs is a widely observed laboratory phenomenon, although many of the early observations went unreported. The weekend effect or DeskTop Spallation (DTS) is characterized by initial survival of a TBC after accelerated laboratory thermal cycling, then failure by exposure to ambient humidity or water. Once initiated, failure can occur quite dramatically in less than a second. To this end, the water drop test and digital video recordings have become useful techniques in studies at NASA (Smialek, Zhu, Cuy), DECHMA (Rudolphi, Renusch, Schuetze), and CNRS Toulouse/SNECMA (Deneux, Cadoret, Hervier, Monceau). In the present study the results for a commercial turbine blade, with a standard EB-PVD 7YSZ TBC top coat and Pt-aluminide diffusion bond coat are reported. Cut sections were intermittently oxidized at 1100, 1150, and 1200 C and monitored by weight change and visual appearance. Failures were distributed widely over a 5-100 hr time range, depending on temperature. At some opportune times, failure was captured by video recording, documenting the appearance and speed of the moisture-induced spallation process. Failure interfaces exhibited alumina scale grains, decorated with Ta-rich oxide particles, and alumina inclusions as islands and streamers. The phenomenon is thus rooted in moisture-induced delayed spallation (MIDS) of the alumina scale formed on the bond coat. In that regard, many studies show the susceptibility of alumina scales to moisture, as long as high strain energy and a partially exposed interface exist. The latter conditions result from severe cyclic oxidation conditions, which produce a highly stressed and partially damaged scale. In one model, it has been proposed that moisture reacts with aluminum in the bond coat to release hydrogen atoms that embrittle the interface. A negative synergistic effect with interfacial sulfur is also invoked.

Smialek, James↗
DOE OSTI2023

Cast iron alloy for automotive engine applications with superior high temperature oxidation properties

A cast iron alloy is provided with a composition in weight percent (wt. %) of carbon between 2.6 to 3.4 wt. %, silicon between 2.4 to 3.2 wt. %, manganese between 0.3 to 0.6 wt. %, molybdenum between 0.4 to 1.2 wt. %, nickel between 0.6 to 1.75 wt. %, magnesium between 0.01 to 0.075 wt. %, aluminum between 1.8 to 3.5 wt. %, sulfur between 0.003 to 0.025 wt. %, zirconium between 0.001 to 0.02 wt. %, cerium between 0.001 to 0.03 wt. %, lanthanum between 0.0005 to 0.02 wt. %, and a balance of iron and unavoidable trace elements. A part formed from the cast iron alloy is also provided and the part has an Ac1 temperature equal to or greater than 895° C. and a thermo-mechanical fatigue lifetime of at least 10,000 cycles when cycled between 400° C. to 800° C. with a total cyclic strain equal to 0.001 m/m.

Godlewski, Larry Alan↗
DOE OSTI2020

Radiolytic degradation of formic acid and formate in aqueous solution: modeling the final stages of organic mineralization under advanced oxidation process conditions

The successful use of advanced oxidation processes to treat aqueous solutions containing undesirable organic species requires the degradation of these species to lower molecular weight, lower hazard compounds. Safe application of this technology requires a thorough understanding of the mechanisms of degradation. These oxidative transformations are mainly initiated by the reactions of reactive oxygen species, particularly hydroxyl radicals. These react with organic molecules to generate carbon-centered radicals. In the presence of dissolved oxygen, the carbon-centered radicals are next converted to peroxyl radicals, which then decay to lower molecular weight species by multiple mechanistic pathways. Formic acid and its conjugate base formate are the last stable chemical species produced immediately before the complete mineralization of any organic molecule undergoing oxidative degradation in aqueous solution. Once understood, the radical-induced chemistry of formic acid/formate under these conditions has wide applicability in all advanced oxidation technologies. To develop this quantitative knowledge, here we have performed a series of 60 Co gamma irradiation studies on aqueous formic acid/formate over different pH and solution conditions. The measured species concentration changes, as a function of applied dose, are compared with the predictions of a kinetic computer model constructed from literature reactions and reported rate coefficients. The excellent agreement found between the results and modeling gives confidence in the mechanism presented here and provide the first complete computer model for the radiolytic degradation of formic acid in water.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Electrochemical properties of poly(ethylene oxide) electrolytes above the entanglement threshold

The ion transport in electrolytes depends on three transport coefficients, conductivity (κ), salt diffusion coefficient (D), and the cation transference number with respect to the solvent velocity ($t_+^0$), and the thermodynamic factor ($T_f$). Current methods for determining these parameters involve four separate experiments, and the coupled nature of the equations used to determine them generally results in large experimental uncertainty. We present data obtained from 64 independent polymer electrolytes comprising poly(ethylene oxide) (PEO) and lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) salt. The molecular weights of PEO ranged from 5 to 275 kg mol -1 ; these samples are all above the entanglement threshold. We minimize the experimental uncertainty in transport and thermodynamic measurements by exploiting the fact that ion transport in entangled polymer electrolytes should be independent of molecular weight. The dependence of $κ, D, t_+^0$, and $T_f$ as a function of salt concentration in the range 0.035 ≤ r ≤ 0.30 are presented with a 95% confidence interval, where r is the molar ratio of lithium ions to ethylene oxide monomer units. While κ, D, and $T_f$ are all positive as required by thermodynamic constraints, there is no constraint on the sign of $t_+^0$. We find that $t_+^0$ is negative in the salt concentration range of 0.093 ≤ r ≤ 0.189.

25 ENERGY STORAGE↗
NASA NTRS1971

Thermomechanical and Thermochemical Behavior of a Hafnium-20 Percent Tantalum Alloy

An investigation was conducted to determine the thermomechanical and thermochemical behavior of a high temperature, oxidation resistant, hafnium-20 percent tantalum alloy. The elastic and shear moduli of this alloy were determined in air up to 1000 C and in vacuum up to 2000 C using a mechanical resonance technique. The internal friction of the alloy was measured up to temperatures greater than 1400 C. Room temperature stress-strain behavior of the oxidized and unoxidized alloy was established. The effect of annealing on the elastic and shear moduli of the extruded rod material was investigated. The martensitic-type phase transformation occurring in the alloy was studied using hot stage metallography and electron microscopy. Static oxidation tests were conducted on the alloy at temperatures from 1000 C to 1700 C with weight gain measurements made as a function of time and temperatures. Surface morphology studies were conducted on the oxide coatings formed at the different temperatures using scanning electron microscopy and X-ray diffraction techniques.

Howell, J. P.↗
NASA NTRS1987

High-temperature oxidation/corrosion of iron-based superalloys

The oxidation and sulfidation of several novel iron-base superalloys were evaluated in high-temperature cyclic tests. The experimental austenitic alloys examined were modifications of NASAUT-4GA which were developed for Stirling-engine application. The weight gains and resulting surface scales were measured and analyzed. Mixed oxide scales were found to form on all specimens exposed above 871 C. The build-up of these scales led to a depletion of Mn and Cr in a zone adjacent to the oxides. In addition, the initial oxidation of the Fe-rich alloy was inhibited by a thin but tenacious Si layer which formed at the interface between oxides and the parent layer. Sulfidation tests using Na2SO4 coatings resulted in the formation of a protective spinel and alpha-Fe2O3 phases. Preferential attack of the carbide phase by hydrogen was not observed after 350 h at 871 C.

Lemkey, F. D.↗
NASA NTRS1954

Preliminary Investigation of Performance and Starting Characteristics of Liquid Fluorine : Liquid Oxygen Mixtures with Jet Fuel

The performance of jet fuel with an oxidant mixture containing 70 percent liquid fluorine and 30 percent liquid oxygen by weight was investigated in a 500-pound-thrust engine operating at a chamber pressure of 300 pounds per square inch absolute. A one-oxidant-on-one-fuel skewed-hole impinging-jet injector was evaluated in a chamber of characteristic length equal to 50 inches. A maximum experimental specific impulse of 268 pound-seconds per pound was obtained at 25 percent fuel, which corresponds to 96 percent of the maximum theoretical specific impulse based on frozen composition expansion. The maximum characteristic velocity obtained was 6050 feet per second at 23 percent fuel, or 94 percent of the theoretical maximum. The average thrust coefficient was 1.38 for the 500-pound thrust combustion-chamber nozzle used, which was 99 percent of the theoretical (frozen) maximum. Mixtures of fluorine and oxygen were found to be self-igniting with jet fuel with fluorine concentrations as low as 4 percent, when low starting propellant flow rated were used.

ENGINES, ROCKET↗
NASA NTRS1993

Reaction of YBa2Cu3O(7-beta) with Gold, Silver, Bismuth and Lead: Substitution Chemistry and Composite Fabrication

The reaction of YBa2Cu3O(7-beta) with Au, Ag, Bi, and Ph ions or metal is described. Three types of materials were produced: a well-defined series of homogeneous superconductors was obtained for Au ion substitution with little effect on T(sub c); attempted Ag and Bi ion substitution resulted in multi-phase samples with slightly enhanced T(sub c); finally, attempts to produce superconducting metal/superconducting ceramic composites with Pb and Bi powders resulted in multi-phase samples with drastically diminished superconducting properties. For Au- substituted superconductors, YBa2(Cu(l-x)Au(x))3O(7-beta), a substitution series (x = 0 - 0.1) has been synthesized. For x = 0.1 there was no change in the a and b lattice parameters (a = 3.826 A and b = 3.889 A) but a 0.06 A c axis expansion to 11.75 A was observed. The valence of Cu and Au in YBa2Au(0.3)Cu(2.7)O(7-beta) was investigated using X-ray Absorption Near-Edge Structure (XANES). X-ray studies indicate that Au goes into the Cu(l) site and Cu K edge XANES shows that this has little effect on the oxidation state of the remaining copper. A small effect on T(sub c) is observed (T(sub c) = 89 K for x = 0.10). Ag and Bi addition results in a rise in T(sub c) and a decrease in (delta)T(sub c) at low levels (x = 0.10 Ag, T(sub c) = 94 K and (delta)T(sub c) = 0.5 K; x = 0.02 Bi, T(sub c) = 94 K and (delta)T(sub c) = 1K) relative to typical values for YBa2Cu3O(7-beta) (T(sub c) = 91 K, (delta)T(sub c) = 2 K). Attempts at fabrication of Pb- and Pb(1-x)Bi(x)-superconductor composites are described. Cold pressing followed by low temperature (200 C) sintering resulted in a composite which excluded flux below 90 K but did not show zero electrical resistance until the metal (alloy) superconducting transition. X-ray diffraction showed the presence of pervoskite and metal. Processing at moderate (450 C) or high (950 C) temperatures resulted in oxygen-depleted pervoskite and/or metal oxides. These materials displayed greatly degraded superconducting properties. Processing at 800 C resulted in high T(sub c) only for composites containing greater than 90% weight fraction ceramic. Reaction of metal with YBa2Cu3O(7-beta) formed superconducting lead/bismuth-based oxides and other binary oxides.

Hepp, Aloysius F.↗
NASA NTRS1988

The effect of 0.1 atomic percent zirconium on the cyclic oxidation behavior of beta-NiAl for 300 hours at 1200 C

The long time effect of 0.1 at percent Zr (0.2 wt percent Zr) on the cyclic oxidation behavior of hipped beta-NiAl was studied. Oxidation testing was performed in static air at 1200 C for up to 3000 one-hour exposure cycles. Specific weight change versus time data was modeled with the COSP computer program to analyze cyclic oxidation behavior. The Zr-free stoichiometric alloy oxidized and spalled randomly to bare metal between cycles at a rate high enough to deplete Al to a low enough level that oxidation breakaway took place as nonprotective NiO replaced the alpha-Al2O3/NiAl2O4 scale as the controlling oxide. The Zr minimized this severe type of spalling maintaining the protective alpha-Al2O3 scale even out to 3000 hours for the stoichiometric alloy with no significant Al depletion. A third beta-NiAl alloy containing 0.1 at percent Zr but with 10 percent less Al than the stoichiometric alloy was also tested and showed some depletion of Al, but the protective Al2O3/NiAl2O4 was still maintained to close to 2700 hours.

Barrett, C. A.↗
NASA NTRS1989

The effect of 0.1 atomic percent zirconium on the cyclic oxidation behavior of beta-NiAl for 3000 hours at 1200 C

The long time effect of 0.1 at percent Zr (0.2 wt percent Zr) on the cyclic oxidation behavior of hipped beta-NiAl was studied. Oxidation testing was performed in static air at 1200 C for up to 3000 one-hour exposure cycles. Specific weight change versus time data was modeled with the COSP computer program to analyze cyclic oxidation behavior. The Zr-free stoichiometric alloy oxidized and spalled randomly to bare metal between cycles at a rate high enough to deplete Al to a low enough level that oxidation breakaway took place as nonprotective NiO replaced the alpha-Al203/NiAl204 scale as the controlling oxide. The Zr minimized this severe type of spalling maintaining the protective alpha-Al203 scale even out to 3000 hours for the stoichiometric alloy with no significant Al depletion. A third beta-NiAl alloy containing 0.1 at percent Zr but with 10 percent less Al than the stoichiometric alloy was also tested and showed some depletion of Al, but the protective Al203/NiAl204 was still maintained to close to 2700 hours.

Barrett, C. A.↗
NASA NTRS1980

The enhanced oxidation of SO2 by NO2 on carbon particulates

The oxidation of SO2 on carbon particles in dry air and in air at 65% relative humidity (RH) was found to be greatly enhanced by the presence of gaseous NO2. Exposures of 20-80ppm SO2 + 10ppm NO2 on 1-mg samples of commercial carbon black were found to produce both sorption and desorption coverages (weight retained after desorption into N2) of over one order of magnitude greater than for corresponding SO2 exposures. Significant agglomeration and wetting were observed to occur progressively during exposures at 65% RH, and samples, even after 150-h exposure, rarely reached steady-state weight gain. The wetting may have regenerated fresh reactive carbon surface. Sorptions conducted in nitrogen atmospheres, rather than in air, appeared to produce slightly higher sorptions and weight retentions for equivalent exposure concentrations and times, indicating that NO2 served as the oxidizer and that molecular oxygen, or some trace constitutents in air, may have weakly inhibited the oxidation by NO2. Wet chemical analysis of the desorbed phase indicated that sulfate, presumably H2SO4 accounted for over half of the retained weight. Measurements of pH from water-quenched samples indicated a highly acidic surface phase, and suggested the oxidation process could proceed in an acidic environment.

Cofer, W. R., III↗
NASA NTRS2003

Wafer-Level Membrane-Transfer Process for Fabricating MEMS

A process for transferring an entire wafer-level micromachined silicon structure for mating with and bonding to another such structure has been devised. This process is intended especially for use in wafer-level integration of microelectromechanical systems (MEMS) that have been fabricated on dissimilar substrates. Unlike in some older membrane-transfer processes, there is no use of wax or epoxy during transfer. In this process, the substrate of a wafer-level structure to be transferred serves as a carrier, and is etched away once the transfer has been completed. Another important feature of this process is that two electrodes constitutes an electrostatic actuator array. An SOI wafer and a silicon wafer (see Figure 1) are used as the carrier and electrode wafers, respectively. After oxidation, both wafers are patterned and etched to define a corrugation profile and electrode array, respectively. The polysilicon layer is deposited on the SOI wafer. The carrier wafer is bonded to the electrode wafer by using evaporated indium bumps. The piston pressure of 4 kPa is applied at 156 C in a vacuum chamber to provide hermetic sealing. The substrate of the SOI wafer is etched in a 25 weight percent TMAH bath at 80 C. The exposed buried oxide is then removed by using 49 percent HF droplets after an oxygen plasma ashing. The SOI top silicon layer is etched away by using an SF6 plasma to define the corrugation profile, followed by the HF droplet etching of the remaining oxide. The SF6 plasma with a shadow mask selectively etches the polysilicon membrane, if the transferred membrane structure needs to be patterned. Electrostatic actuators with various electrode gaps have been fabricated by this transfer technique. The gap between the transferred membrane and electrode substrate is very uniform ( 0.1 m across a wafer diameter of 100 mm, provided by optimizing the bonding control). Figure 2 depicts the finished product.

Yang, Eui-Hyeok↗
DOE OSTI2020

Fabrication of yttrium hydride for high-temperature moderator application

We report given the superior thermal stability and highly attainable hydrogen density, yttrium hydride is an excellent high-temperature moderator material in advanced thermal neutron spectrum reactors that require small core volumes. Large-scale, crack-free, bulk yttrium hydride is in high demand; however, fabrication of yttrium hydride is challenging and has not been demonstrated for nearly half century. The associated challenges are discussed herein. In response to these challenges, a hydriding system was designed and constructed at Oak Ridge National Laboratory and was used to successfully fabricate crack-free yttrium hydride in complex geometries at large scales. This was accomplished by precisely controlling the hydrogen’s partial pressure and the retort temperature, which was informed by the well-established thermodynamic properties of the binary H–Y system. Hydrogen content in as-fabricated hydride was determined by weight change, an approach which was considered reliable based on the use of ultra–high-purity yttrium, the absence of oxide phases up to levels detectable using x-ray diffraction (XRD), and the significant weight gain. Hydrogen distribution along one yttrium hydride rod was evaluated with XRD analysis on materials extracted from different locations on the rod. The results indicated a relatively homogeneous hydrogen distribution along the hydride rod, with <3% uncertainty in the fraction of the δ-phase hydride. In addition, significant efforts are being dedicated to establish a complete database summarizing the thermomechanical and physical properties of as-fabricated yttrium hydride and the irradiation response to facilitate its deployment as a high-temperature moderator in advanced nuclear reactors.

36 MATERIALS SCIENCE↗
NASA NTRS1987

High temperature isothermal and cyclic oxidation behavior of a single crystal Ni base superalloy

High-temperature oxidation behavior of a Ni-base superalloy, PWA1480, developed for use as single-crystal blades and vanes in advanced gas turbines, has been assessed. Isothermal and cyclic oxidation tests up to 200 hours were conducted at 1323, 1410, and 1473 K. The alloy was evaluated as to sample weight change, type of scale formed, type and amount of spall, and microstructural changes. The oxidation attack was more severe in cyclic as compared with isothermal oxidation. Also, enormous growth of the gamma-prime precipitate was observed at 1423 K during cyclic oxidation.

Hebsur, M. G.↗