Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “low-temperature”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Electropolishing-induced topographic defects in niobium: Insights and Implications for SRF

Electropolishing (EP) is the premier surface preparation method for high-Q, high-gradient superconducting RF cavities made of Nb. This leaves behind an apparently smooth surface, yet the achievable peak magnetic fields fall well below the superheating field of Nb, in most cases. In this work, the ultimate surface finish of EP was investigated by studying its effect on highly polished Nb samples. EP introduces high slope angle sloped-steps at grain boundaries. The magnetic field enhancement and superheating field suppression factors associated with such a geometry are calculated in the London theory. Despite the by-eye smoothness of electropolished Nb, such defects compromise the stability of the low-loss Meissner state, likely limiting the achievable peak accelerating fields in superconducting RF cavities. Finally, the impact of surface roughness on impurity diffusion is investigated which can link surface roughness to the effectiveness of heat treatments like low-temperature baking or nitrogen infusion in the vortex nucleation or hydride hypotheses. Surface roughness tends to decrease the effective dose of impurities as a result of the expansion of impurities into regions with greater internal angle. The effective dose of impurities can be protected by minimizing slope angles and step heights, ensuring uniformity.

Lechner, Eric [Thomas Jefferson National Accelerat↗
DOE OSTI2026

Jumpstart Opportunities to Unleash Leadership in Energy Storage (JOULES)

Current-generation Li-ion batteries with cobalt- and nickel-containing cathodes and graphite anodes are approaching performance and cost limits. In this program, 24M Technologies, Inc. (24M) is teaming with the Massachusetts Institute of Technology (MIT) and University of Michigan (UM) to develop low cost and fast charging sodium metal batteries with good low-temperature performance and high energy density, building upon previous work performed under ARPA-E programs. Key achievements include optimization of solid electrolyte and anode current collector, optimized cathode active materials, development of high-performance electrolyte formulations, and integration of these components into full cells. The cell design incorporates (1) an ultra-thick cathode (>9 mAh/cm 2 ) comprising advanced cobalt-free, sodium cathode active material, (2) advanced fast-charging electrolyte (up to 12 mS/cm) developed using machine learning and automated high-throughput screening technology by UM, and (3) ceramic modified separator that enable smooth Na transport and deposition, developed at MIT, enabling a high-energy density anode-free configuration and maximizing the energy density of sodium batteries. The team has successfully combined these approaches to sodium chemistry and paved the way to meeting the fast-charging, high-energy density, and low-cost requirements of next-generation drone, electric vertical take-off and -landing, and electric vehicle batteries. Performance for anode-free sodium cells developed under this program is more powerful than the commercial Li-ion batteries. The final deliverable cell design has achieved over 300 Wh/kg and volumetric energy density above 800 Wh/L (Table 1). Additionally, the team has achieved over (1) a lifetime of 340 cycles, (2) 80% capacity retention at -20 °C (compared 25 °C), and (3) the ability to fast charge to 80% SOC in 20 minutes.

25 ENERGY STORAGE↗
DOE OSTI2025

Microstructure and 77K mechanical properties of electron beam welded Cu101- Inconel 625 joints

In developing large-scale next-generation superconducting radio frequency (SRF) linear accelerators using superconducting films on Cu, the design and development of dissimilar welding and joining metals, such as Cu to Inconel, stainless steel, and Nb, are essential. In this talk, we present the development of procedures for electron-beam welding of Cu¿Inconel 625 and evaluation of the microstructure and 77K mechanical properties of the weld and base material in the welded condition and heat treatments in the 750°C ¿950°C heat treatment range. The results will be presented in the context of developing joining techniques for low-temperature applications where high conductivity and strength, vacuum hygiene, and magnetic properties of the material need consideration. The methods presented here are being deployed to thin film SRF Cu cavities at Jefferson Lab. Acknowledgment: This material is based upon work supported by the U.S. Department of Energy, Office of Science, Office of Nuclear

Khanal, Bashu↗
DOE OSTI2026

Hybrid Fuel Cell Systems for Heavy-Duty Trucks: Configuration, Heat Rejection, and Performance

Low-temperature polymer electrolyte membrane fuel cell systems can achieve higher efficiency than diesel engines, but heat rejection remains a major challenge in class-8 heavy-duty fuel cell trucks. For the same rated power, the radiator heat load is greater than that in a diesel engine, while the allowable operating temperatures are lower. This work proposes and evaluates 400 kWe fuel cell–battery hybrid (FCH) platforms and operating strategies that manage heat rejection without enlarging the radiator frontal area. Three FCH platforms are identified, each varying in fuel cell system (FCS) rated power, battery energy storage system (ESS) capacity, and maximum stack coolant exit temperature (T h1 ). All three satisfy key system and vehicle requirements, including 175 kWe FCS power at top sustained speed, 400 kWe FCH power on a 6% grade climb, a target stack power density (PD) of 750 mW e /cm 2 , and heat rejection constraints. The first FCH has the smallest FCS, the largest ESS, and a T h1 of 90 °C. The second achieves the highest PD of 840 mW e /cm 2 at a T h1 of 95 °C. The third has the largest FCS, the smallest ESS, and a T h1 of 102 °C. At a Th1 of 115 °C, the platform can be configured as a stand-alone 400 kWe(net) FCS without hybridization, but the achievable PD drops to 460 mW e /cm 2 .

25 ENERGY STORAGE↗
DOE OSTI2025

Enhancement of Superconductivity in WP via Oxide-Assisted Chemical Vapor Transport

Tungsten monophosphide (WP) has been reported to superconduct below 0.8 K, and theoretical work has predicted an unconventional Cooper pairing mechanism. Here we present data for WP single crystals grown by means of chemical vapor transport (CVT) of WO3, P, and I2. In comparison to synthesis using WP powder as a starting material, this technique results in samples with substantially decreased low-temperature scattering and favors a more three-dimensional morphology. We also find that the resistive superconducting transitions in these samples begin above 1 K. Variation in Tc is often found in strongly correlated superconductors, and its presence in WP could be the result of influence from a competing order and/or a non-s-wave gap.

Chemistry↗
DOE OSTI2025

Extraction of Terpenoids from Pine Needle Biomass Using Dimethyl Ether

Pine needles are an industrial feedstock for extracts used in a variety of applications, but conventional extraction methods often result in a degradation of the terpenoid compounds that naturally occur in loblolly pine ( Pinus taeda ). Separation of these compounds from pine biomass is an energy-intensive operation, typically requiring a significant input of thermal energy. An alternative separation approach with potential energy savings is extraction with a condensable gas, namely, dimethyl ether. Biomass materials are exposed to liquid dimethyl ether under pressure, which mobilizes the organics. The extract is then separated from the insoluble pine matter, and dimethyl ether is volatilized away from the separated organic species. A variety of terpene derivatives were extracted from pine needle biomass using this approach, including monoterpenes, sesquiterpenes, and related oxygenates, which were identified using two-dimensional gas chromatography/mass spectrometry. Additionally, the dimethyl ether-treated needles resemble needles subjected to low-temperature drying, whereas needles treated with a high-temperature drying method appear to have shrunken structures. The results suggest that dimethyl ether extraction has significant potential for separating valuable organics from complex matrices without the application of thermal energy during treatment.

dimethyl ether (DME) extraction↗
DOE OSTI2025

High Field Magnet Programme -- European Strategy Input

In this submission, we describe research goals, implementation, and timelines of the High Field Magnet Programme, hosted by CERN. The programme pursues accelerator-magnet R&D with low-temperature- and high-temperature superconductor technology with a main focus on the FCC-hh. Following a long tradition of magnet R&D for high-energy particle colliders, HFM R&D fosters important societal impact through synergies with other fields.

43 PARTICLE ACCELERATORS↗
DOE OSTI2026

Evaluation of UKESM aerosol size and composition using ATom measurements indicates missing marine aerosol formation mechanisms

Atmospheric aerosols influence climate through their interactions with radiation and clouds, yet large uncertainties remain in their simulation by global models. This study evaluates the United Kingdom Earth System Model version 1.1 (UKESM1.1) using global-scale aircraft observations from the Atmospheric Tomography (ATom) mission, focusing on aerosol lifecycle processes in the remote marine atmosphere. We assess model performance in simulating aerosol precursor vapours, number size distributions, chemical composition, and environmental conditions. Several process improvements are tested, including sulfuric acid-ammonia nucleation, ammonium nitrate scheme, methanesulfonic acid condensation, and low-temperature isoprene-derived secondary organic aerosol formation. Model biases differ significantly between the upper troposphere (UT) and the marine boundary layer (MBL). In the UT, UKESM1.1 overestimates nucleation and Aitken mode particles while underestimating accumulation mode, indicating insufficient growth. In the MBL, the model overestimates primary aerosols (e.g. seasalt) and precursor gases but underestimates nucleation and Aitken mode particles, even after incorporating updated nucleation and ammonium nitrate scheme. The persistence of low aerosol number concentrations, despite overestimated precursors, suggests missing formation pathways likely involving other species such as iodine, amines, and organic vapours. These limitations result in an unbalanced cloud condensation nuclei budget that over-relies on primary emissions. Sensitivity tests reveal that model outputs are strongly influenced by dimethyl sulfide emissions and vapour condensation schemes. Our results highlight the need for future model development to prioritise mechanistic representation of currently missing aerosol sources, rather than relying on empirical tuning, to improve aerosol-climate interaction estimates.

He, Xu-Cheng [Univ. of Cambridge (United Kingdom);↗
DOE OSTI2025

Activation of propane on Ag–PdO(101) model surfaces

Oxidation of alkanes remains a central challenge in catalysis due to the high activation barriers of C–H bonds and the thermodynamic favorability of complete oxidation. Palladium oxide (PdO), particularly its (101) facet, is known for its high reactivity in alkane oxidation, which is attributed to its coordinatively unsaturated palladium (Pd) and O atoms. In this study, we investigate the effect of silver (Ag) incorporation on the oxidation behavior of propane over PdO(101) using temperature-programmed reaction spectroscopy (TPRS) under controlled conditions. While pristine PdO(101) exhibits complete oxidation of propane with CO₂ and H₂O desorption at high temperatures (approximately 475 K), Ag incorporation induces a new CO₂ desorption peak at significantly lower temperatures (approximately 330 K). This shift is attributed to the formation of new active sites at the Ag–PdO(101) interface. Quantitative analysis reveals that low-temperature activity correlates with Ag coverage, while overall CO₂ production decreases, suggesting a redistribution of reactivity rather than an increase in active surface area. Activation energy estimations using the Redhead method confirm that C–H bond activation becomes more facile at the interface, with a 46 kJ/mol reduction compared to pristine PdO(101). These findings demonstrate that incorporating a less reactive metal such as Ag into PdO surfaces not only modifies the reaction energetics but also enables the design of bimetallic catalysts with improved selectivity for partial oxidation reactions.

Chemistry↗
DOE OSTI2026

H2@Scale - Validating an Electrolysis System with High Output Pressure: Cooperative Research and Development Final Report, CRADA Number CRD-18-00741

Electrolysis has been a commercially available product for a while and electrolyzers have been a proven capability to provide additional benefits (e.g. controllable load for grid services) in addition to production of hydrogen. The hydrogen output is typically compressed for storage and dispensing. Compression adds cost and decreases system reliability. Honda’s electrolyzer systems have been developed to include electrochemical compression to leverage the production system itself for at least partial compression. In this project, the team will evaluate Honda’s PEM based electrochemical compression system. The system is capable of compressing hydrogen up to 70 MPa electrochemically. Validation testing is the next step to accelerate this technology into the marketplace, as the validation will provide needed data under a variety of operation conditions and controls. These operating conditions and controls are based on over a decade of NLR research and development with low-temperature electrolysis. The validation testing will include preparing NLR’s site for third party evaluation, benchmark testing of Honda’s stack and system, and simulating operation connected to renewables or in a grid service profile. NLR’s Energy System Integration Lab will be the location for the electrolyzer validation research and integrated into the Hydrogen Infrastructure Test & Research Facility (HITRF). This will build into the existing retail style hydrogen fueling station for a fully integrated experimental setup.

08 HYDROGEN↗
NASA NTRS1951

Ignition-delay Characteristics in Modified Open-cup Apparatus of Several Fuels with Nitric Acid Oxidants Within Temperature Range 70 to 105 Degrees F

Fluid properties and low-temperature ignition delays were obtained for approximately 90 fuel-oxidant combinations. A red fuming nitric acid containing approximately 3 percent water and 19 percent nitrogen tetroxide froze at approximately -87 degrees F and ignited several low-viscosity fuel blends of aromatic amines in triethylamine at -76 degrees F and lower. With this acid, the following average ignition delays were obtained with a blend of 30 percent o-toluidine in triethylamine: ...

FUEL SYSTEMS - ENGINES, ROCKET↗
NASA NTRS2026

Molecular Inventory and Comparative Organic Profiling of A Homogenized Aggregate Sample From Asteroid (101955) Bennu

Evaluating the distribution and diversity of solvent-soluble organic molecules in extraterrestrial materials provide information about the physicochemical environments where prebiotic chemistry occurred and is essential for assessing the inventory of prebiotic compounds available to the early Earth. In this work, we conducted a comprehensive molecular characterization of solvent-soluble organic compounds in a homogenized aggregate sample (ID: OREX-800107-128) of unsorted regolith from asteroid (101955) Bennu returned by NASA’s OSIRIS-REx mission. Using two-dimensional gas chromatography coupled with high-resolution time-of-flight mass spectrometry (GC×GC-HRMS), we identified 87 organic compounds across several molecular classes, including alkanes, polycyclic aromatic hydrocarbons, and nitrogen-, oxygen-, and sulfur-bearing species. Comparison with the organic inventory of CI (Orgueil), C2-ungrouped (Tagish Lake and Tarda), and CM2 (Murchison) carbonaceous chondrites revealed that Bennu sample OREX-800107-128 is most similar to Tagish Lake and Tarda yet compositionally distinct from all of these meteorites. This Bennu sample exhibits a relatively high abundance of low-molecular-weight aromatics (e.g., toluene), pyridine derivatives, and sulfur species such as dimethyl sulfite, consistent with episodic low-temperature aqueous alteration. The presence of these organic compounds suggests that this material experienced chemically diverse processes in the parent body conducive to complex organic synthesis, including aldol condensation reactions responsible for N- and O-bearing compounds. We also compared the molecular distributions of this Bennu sample and previously analyzed samples from (162173) Ryugu to assess potential common origins between these two carbonaceous asteroids. Bennu shows more chemically diverse and nitrogen-rich organic materials than Ryugu. While both asteroids share broadly similar primitive compositions, the observed chemical differences indicate distinct evolutionary histories within a likely common formation environment though whether Bennu and Ryugu derive from a single compositionally heterogeneous parent body or from multiple closely related progenitors remains unresolved. Further detailed comparative analyses of material from Bennu, Ryugu, and specific carbonaceous meteorites (e.g., Tagish Lake and Tarda) will provide new insights into how the N-rich molecular profile observed in Bennu samples was formed and evolved in the outer Solar System.

sample return↗
NASA NTRS2026

A Review of Superconducting Electric Machines with On-Board Cryocoolers

This paper reviews the evolution and emerging direction of superconducting electric machines that employ onboard cryocoolers integrated directly into the rotor, eliminating the need for cryogenic fluid coupling and, in some cases, rotary seals. Traditional low-temperature superconducting (LTS) machines relied on external cryogenic systems and liquid helium transfer couplers, which introduced excessive complexity, poor reliability, and significant parasitic energy losses. The advent of high-temperature superconductors (HTS) has enabled compact, closed-cycle cryocoolers that support self-contained, fluid-free refrigeration architectures suitable for rotating applications. This paper examines the key technological challenges associated with on-board cryocooler integration and reviews three representative efforts by KAIST, NASA, and Hinetics, each illustrating distinct strategies and milestones toward practical implementation. KAIST demonstrated early proof-of-concept for rotating machines with on-board cryocoolers, NASA developed a shaft-integrated Stirling-type pulse tube cryocooler for a 1.4 MW hybrid-electric motor, and Hinetics achieved full-scale validation of a self-contained HTS rotor incorporating a commercial Stirling cryocooler and spoke-suspension torque tube. Collectively, these achievements confirm the technical feasibility of on-board cryogenic refrigeration and highlight steady progress toward compact and efficient superconducting rotating systems across various applications. Embedding cryocoolers directly within the rotor enables practical, efficient, and commercially viable superconducting propulsion technologies.

Cryogenics↗
NASA NTRS2026

List of Commercial and Advanced Developmental Niobium-Based Alloys of the Space Age

This report compiles a list of commercial and developmental niobium-based alloys developed during the Space Age (late 1950s through mid-1970s) for extreme-temperature applications, including rocket engine thrust chambers, hypersonic re-entry thermal protection systems, and space fission reactor loops. Niobium (Nb) was widely pursued because it provided the lowest density (~8.6 g/cc) among the primary refractory metals, a high melting temperature (~2470°C), exceptional low-temperature ductility, good formability, and compatibility with liquid alkali metals. An evaluation of physical metallurgy mechanisms, focusing on solid-solution strengthening via heavy refractory solutes (W, Mo, Ta), dual-purpose reactive solutes (Hf, Zr, Ti), and dispersion strengthening using carbides, nitrides, and oxides is presented. Additionally, the report compares Western and Soviet Union metallurgical approaches, explaining how supply chain factors and manufacturing infrastructure influenced element selection, interstitial chemistry, and alloy identification/naming conventions. Cataloging these historical alloy chemical compositions serves as a foundational reference for modern alloy additive manufacturing, thermodynamic CALPHAD modeling, and machine-learning discovery pipelines for next-generation extreme-environment niobium-based alloys.

Physical Metallurgy↗
NASA NTRS2025

A Review of Direct Ink Writing of Polymer Derived Ceramics

With the growing demand for materials capable of withstanding extreme temperatures and pressures, ceramic components with exceptional corrosion resistance and reliable mechanical properties have experienced a significant surge in demand. However, traditional ceramic forming methods involve high-temperatures and energy-intensive processes that often struggle to produce complex parts or composites efficiently. Polymer-Derived Ceramics (PDCs) offer a transformative solution by using polymeric precursors that can be converted into a wide variety of silicon-based and non-silicon-based ceramics through heat treatment. The polymeric nature of PDC precursors enables the fabrication of geometrically intricate components using conventional polymer-forming techniques at significantly lower processing temperatures. Furthermore, PDCs are well-suited for additive manufacturing (AM), allowing the production of complex structural and functional components through cost-effective, low-temperature processes. By leveraging the diverse properties of PDC materials – each with unique advantages and limitations – manufacturers can optimise performance for specific applications. This review provides an overview of the types of PDCs developed to date and their broad range of applications. Specifically, it delves into the Direct Ink Writing (DIW) process, exploring its rheological requirements and the critical role of fillers in tailoring the rheological properties of polymeric precursors to meet the specific demands of DIW.

Victoria Bishop↗
DOE OSTI2025

Verification of a Fluid-Based Plasma-Edge Model Within the Multiphysics Object-Oriented Simulation Environment (MOOSE) Framework

As the goal of achieving fusion power on the grid comes closer to fruition, fully coupled multiphysics models of fusion devices will be crucial. These models must incorporate the interconnected phenomena of these devices, including plasma physics, neutronics, first wall interactions, and tritium transport. Currently, there are two main approaches to developing these platforms: (1) loosely coupled, where one couples existing codes and solvers together through input and output parameters and data, and (2) tightly coupled, where one develops the necessary models within a singular, integrated framework. This work focuses on the latter approach for magnetically confined fusion devices by developing a fluid-based plasma-edge model within the Multiphysics Object Oriented Simulation Environment (MOOSE) Framework. This effort is coordinated with other efforts to develop, test, demonstrate, and deploy fusion relevant multiphysics capabilities including electromagnetics, particle-in-cell plasma, tritium transport, and fusion blanket design. This new model is an expansion of the MOOSE-based plasma application, Zapdos, which was originally formulated to model low-temperature, non-magnetized plasma processes. Verification studies have been conducted using newly developed magnetic plasma capabilities. These involved convergence analyses utilizing the method of manufactured solutions to verify new operators and case studies. A modular approach was taken here to demonstrate increasingly complicated simulation scenarios, which included a singular fluid with uniform magnetic field case, a singular fluid with spatially varying magnetic field case, and a coupled multifluid case.

70 - PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Kinetic Plasma Simulation Capabilities in the MOOSE Framework: Verification of Particle-Particle Collisions

High-fidelity simulations of complex plasma systems allow researchers to gain key insights into and understanding of these systems. To facilitate massively parallel high-fidelity plasma simulations, finite-element-based particle-in-cell capabilities are being developed within the open-source Multiphysics Object-Oriented Simulation Environment (MOOSE) based framework called Software for Advanced Large-scale Analysis of MAgnetic confinement for Numerical Design, Engineering & Research (SALAMANDER). While SALAMANDER’s primary objective is modeling edge plasmas and plasma-facing components in fusion devices, the particle-in-cell capabilities being developed are general and will support modeling low-temperature plasmas as well. Previously, collisionless magnetostatic simulation capabilities have been verified with the two-stream and Dorey-Guest-Harris instabilities, and single particle motion. Collisions were implemented using the direct simulation Monte Carlo method, and verification of this capability will be presented here several verification problems: relaxation of a randomly initialized gas to a Maxwellian distribution, Fourier heat flow, and comparison of reaction rates to both analytic calculations and those calculated using a multi-term Boltzmann solver.

70 - PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

The Verification and Validation of a Magnetic Plasma Fluid Model Utilizing the MOOSE (Multiphysics Object Oriented Simulation Environment) Framework

As the goal of achieving fusion power on the grid comes closer to fruition, fully coupled multiphysics models of fusion devices will be crucial. Currently, there are two main approaches to developing these platforms: (1) loosely coupled, where one couples existing codes and solvers together through input and output parameters and data, and (2) tightly coupled, where one develops the necessary models within a singular, integrated framework. This work focuses on the latter approach for magnetically confined fusion devices by developing a fluid-based plasma-edge model within the Multiphysics Object Oriented Simulation Environment (MOOSE) Framework. This effort is coordinated with other efforts to develop, test, demonstrate, and deploy fusion relevant multiphysics capabilities including electromagnetics, particle-in-cell plasma, tritium transport, and fusion blanket design. This new model is an expansion of the MOOSE-based plasma application, Zapdos, which was originally formulated to model low-temperature, non-magnetized plasma processes. Verification, benchmarking, and validation studies have been conducted. Verification studies involved utilizing the method of manufactured solutions and comparing the convergence slope of a known solution to the theoretical slope. Benchmarking consists of comparisons to existing edge codes, namely BOUT++ and SOLEDGE3X. Validation efforts focused on comparisons against open-source data from the TCV tokamak.

70 - PLASMA PHYSICS AND FUSION TECHNOLOGY↗