Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “liquid and solid electrolytes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Highly efficient interface stabilization for ambient-temperature quasi-solid-state sodium metal batteries

Solid-state sodium (Na) batteries (SSSBs) using sulfide-based solid electrolytes (SSEs) hold tremendous promise due to their high theoretical specific capacity, enhanced safety and abundant resources. However, detrimental interfacial issues between SSEs and Na metal present a major challenge to the advancement of sulfide-based SSSBs. To address interfacial issues, we demonstrate an efficient approach by incorporating an ionic liquid electrolyte ((PYR/Na)TFSI) as interlayer to stabilize the Na metal/SSE interface. The presence of the (PYR/Na)TFSI interlayer enables the formation of a stable solid electrolyte interphase (SEI) to prevent the harmful reactions and inhibit Na dendrites. Combination of ab initio molecular dynamics simulations and X-ray photoelectron spectroscopy revealed that this stable SEI is largely composed of reduced products of TFSI -, such as NaF and CF 3 . As a result, the symmetric cells exhibited stable Na plating/striping cycling for 300 h at 0.1 mA cm -2 . In addition, FeS2||Na quasi-solid-state batteries delivered an impressive specific capacity of over 300 mAh g -1 under the current density of 20 mA g -1 at room temperature. Under a higher current density (100 mA g -1 ), such batteries performed with long-term cycling stability and maintained a specific capacity of around 103 mAh g -1 after 330 cycles. This work demonstrates the novel perspective of using an ionic liquid interlayer to address interfacial issues, contributing to the advancement of high-performance SSSBs for the next-generation energy storage systems.

25 ENERGY STORAGE↗
DOE OSTI2022

Enabling Conversion-Type Iron Fluoride Cathode by Halide-Based Solid Electrolyte

The practical application of low-cost and energy-dense iron fluoride cathodes has been hindered by the first cycle electrochemical irreversibility, cycling instability, and large voltage hysteresis. Here, we report that these challenges may be overcome by the utilization of halide-based solid electrolytes (SEs). The excellent electrochemical stability of halide-based SEs enables a complete conversion and deconversion of FeF 2 which cannot be achieved with sulfide-based SEs. Due to restricted and reversible decomposition of SE, prevention of Fe dissolution, mechanical confinement of active material, as well as improved electrode kinetics, solid-state FeF 2 cathode with halide-based SE demonstrated superior electrochemical performance compared with FeF 2 electrodes in liquid electrolytes, with a high 1st cycle coulombic efficiency (~100 %), high specific capacity (~600 mAh/g), long cycle life (>100 cycles) and high-rate performance (up to 2C). In conclusion, our results suggest solidifying the batteries may be a viable approach to addressing the long-standing key challenges of iron fluoride cathodes.

25 ENERGY STORAGE↗
DOE OSTI2023

Solid–Adsorbed Polymer–Electrolyte Interphases for Stabilizing Metal Anodes in Aqueous Zn and Non–Aqueous Li Batteries

Polymers are known to adsorb spontaneously from liquid solutions in contact with high-energy substrates to form configurationally complex, but robust phases that often exhibit higher durability than might be expected from the individual physical bonds formed with the substrate. Rational control of the physical, chemical, and transport properties of such interphases has emerged as a fundamental opportunity for scientific and technological advances in energy storage technology but requires in-depth understanding of the conformation states and electrochemical effect of the adsorbed polymers. Here, we analyze the interfacial adsorption of oligomeric polyethylene glycol (PEG) chains of moderate sizes dissolved in protic and aprotic liquid electrolytes and find that there is an optimum polymer molecular weight of approximately 400 Da at which the highest columbic efficiency is achieved for both Zn and Li deposition. Furthermore, these findings point to a simple, versatile approach for extending the lifetime of batteries.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Halide Substitution Effects on Lithium-Ion Diffusion in Protonated Antiperovskites

Solid-state electrolytes (SSEs) for all-solid-state lithium-ion batteries are generating intense interest because these batteries can improve the safety and performance compared with devices fabricated with conventional, flammable liquid electrolytes. In these SSEs, it has been suggested that Li + ion diffusion in the grain boundaries is hindered and is a critical determinant of the overall ionic conductivity (σ). However, Li + ion diffusivities in the grain (D G ) and the grain boundary (D GB ) are difficult to determine experimentally, with few techniques capable of distinguishing the individual contributions. Here, we distinguished the D G and D GB for the protonated lithium antiperovskites (pLiAPs) SSEs: Li 2 OHCl, Li 2 OHBr, Li 2 OHF 0.1 Cl 0.9 , Li 2 OHF 0.1 Br 0.9 , and Li 2 OHCl 0.3 7Br 0.63 . The measurements were obtained directly from 7 Li pulsed-field gradient nuclear magnetic resonance (PFG-NMR) at 353 K. The 7 Li PFG-NMR echo profiles were composed of two primary components with additional secondary oscillatory components – the so-called NMR diffraction phenomenon. The length scale separating the two main components corresponds to a diffusion length of ~1.7 µm, which is thought to be the average grain size (by diameter). The short-range (≤ 1.7 µm) diffusion component associated with D G (≈10 -11 m 2 /s) varied minimally with halide substitution, while the long-range (≥ 1.7 µm) component D GB (≈10 -12 to 10 -15 m 2 /s) was highly sensitive to the substitution of halides and closely correlated with s. In addition, from the comparison of the ratio D GB /D G to D t (the Li + ion diffusion coefficient estimated from the rotational correlation time, t c ), it was determined that the contribution of D G to σ is negligible; 0.01 ~ 0.04 in the pLiAPs studied here. Finally, these insights provide fundamental understanding of the halide substitution effects on Li + ion grain versus grain boundary diffusion, and suggest that careful engineering of the grain boundaries at the microscopic level is necessary to achieve high-performance pLiAP SSEs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Uncovering the Relationship between Diameter and Height of Electrodeposited Lithium Protrusions in a Rigid Electrolyte

A promising approach for enabling rechargeable batteries with significantly higher energy densities than current lithium-ion batteries is by deploying lithium-metal anodes. However, the growth of lithium protrusions during charging presents significant challenges. Since these protrusions are often branched and filamentous in conventional liquid electrolytes, this problem is referred to in the literature as the “dendrite problem”. While solid electrolytes have the potential to solve this problem, protrusions grow in all electrolytes when the current density exceeds a critical value. Fundamentally understanding the formation is necessary to develop a rational approach for increasing the critical current density, but it is challenging due to the complex interplay between electrochemical and material properties. The diameters and heights of protrusions on lithium-metal anodes stabilized by a rigid block copolymer electrolyte were measured in situ by synchrotron hard X-ray microtomography. The diameter of the shorting protrusions increased linearly with increasing electrolyte thickness. Further, a universal linear relationship between protrusion height and diameter of both shorting and non-shorting protrusions was observed. A model based on the concentrated solution theory was used to establish the electrochemical and mechanical sources for our observations. Here, the computational analysis indicates that elastic and plastic deformation of both the lithium metal and the polymer are important to describe protrusion growth. Both stress-induced current density effects due to the deformation of the electrolyte near the protrusion and plastic deformation of lithium metal combine to give the counterintuitive result: the fastest-growing protrusions have the largest diameter.

25 ENERGY STORAGE↗
NASA NTRS1993

Series-Connected Vapor/Vapor AMTEC Cells

Size and weight reduced; operating lifetime increased. Developmental alkali-metal thermal-to-electric converter (AMTEC) in which cells fed from common supply of high-pressure sodium vapor and connected electrically in series. No liquid sodium makes contact with any part of AMTEC cells. Sodium vapor supplied to solid electrolyte of each cell through porous metal anode on upstream side. Proposed design reduces need for high-temperature feedthroughs in that cells internally connected. Power withdrawn through feedthrough at lower temperature without significant thermal loss.

Underwood, Mark L.↗
DOE OSTI2020

Lithium-ion electrolytic substrates for sub-1V high-performance transition metal dichalcogenide transistors and amplifiers

Electrostatic gating of two-dimensional (2D) materials with ionic liquids (ILs), leading to the accumulation of high surface charge carrier densities, has been often exploited in 2D devices. However, the intrinsic liquid nature of ILs, their sensitivity to humidity, and the stress induced in frozen liquids inhibit ILs from constituting an ideal platform for electrostatic gating. Here we report a lithium-ion solid electrolyte substrate, demonstrating its application in high-performance back-gated n-type MoS 2 and p-type WSe 2 transistors with sub-threshold values approaching the ideal limit of 60 mV/dec and complementary inverter amplifier gain of 34, the highest among comparable amplifiers. Remarkably, these outstanding values were obtained under 1 V power supply. Microscopic studies of the transistor channel using microwave impedance microscopy reveal a homogeneous channel formation, indicative of a smooth interface between the TMD and underlying electrolytic substrate. These results establish lithium-ion substrates as a promising alternative to ILs for advanced thin-film devices.

42 ENGINEERING↗
NASA NTRS2009

Small CO2 Sensors Operate at Lower Temperature

Solid-electrolyte-based amperometric sensors for measuring concentrations of CO2 in air are being developed for use in detection of fires, environmental monitoring, and other applications where liquid-based electrochemical cells are problematic. These sensors are small (sizes of the order of a millimeter), are robust, are amenable to batch fabrication at relatively low cost, and exhibit short response times (seconds) and wide detection ranges. A sensor of this type at a previous stage of development included a solid electrolyte of Na3Zr2Si2PO12 deposited mainly between interdigitated Pt electrodes on an alumina substrate, all overcoated with an auxiliary solid electrolyte of (Na2CO3:BaCO3 in a molar ratio of 1:1.7). It was necessary to heat this device to a temperature as high as 600 C to obtain the desired sensitivity and rapid response. Heating sensors increases the power consumption of the sensor system and complicates the use of the sensor in some applications. Thus, decreasing a sensor s power consumption while maintaining its performance is a technical goal of ongoing development.

Hunter, Gary W.↗
DOE OSTI2023

Solid‐Adsorbed Polymer‐Electrolyte Interphases for Stabilizing Metal Anodes in Aqueous Zn and Non‐Aqueous Li Batteries

Abstract Polymers are known to adsorb spontaneously from liquid solutions in contact with high‐energy substrates to form configurationally complex, but robust phases that often exhibit higher durability than might be expected from the individual physical bonds formed with the substrate. Rational control of the physical, chemical, and transport properties of such interphases has emerged as a fundamental opportunity for scientific and technological advances in energy storage technology but requires in‐depth understanding of the conformation states and electrochemical effect of the adsorbed polymers. Here, we analyze the interfacial adsorption of oligomeric polyethylene glycol (PEG) chains of moderate sizes dissolved in protic and aprotic liquid electrolytes and find that there is an optimum polymer molecular weight of approximately 400 Da at which the highest columbic efficiency is achieved for both Zn and Li deposition. These findings point to a simple, versatile approach for extending the lifetime of batteries.

Jin, Shuo↗
DOE OSTI2023

Super p-sulfur cathodes for quasi-solid-state lithium-sulfur-batteries

Lithium-Sulfur (Li-S) batteries have become a promising candidate to meet the current energy storage demand, with its natural abundance of materials, high theoretical capacity of 1672 mAhg-1, high energy density of 2600 Whkg-1, low cost and lower environmental impact. Sulfide based solid state electrolytes (SSEs) have received greater attention due to their higher ionic conductivity, compatible interface with sulfur-based cathodes, and lower grain boundary resistance. However, the interface between SSEs and cathodes has become a challenge in all solid-state Li-S batteries due to the rigidity of the participating surfaces. A hybrid electrolyte containing SSE coupled with a small amount of ionic liquid, was essential to improve the interface contact of the SSE with the electrodes. Coating-based cathodes were successfully fabricated using water-based carboxymethyl cellulose (CMC) solution and Styrene butadiene rubber (SBR) as the binder with low sulfur loading (0.70 mgcm-2) as well as high sulfur loading (4.0 mgcm-2). Solid-state composite powder-based cathodes pressed onto SSE (loading 4.0 mgcm-2) with enhanced electronic and ionic conductivity were fabricated with Super P: Sulfur (SP:S) and SSE. Ionic Liquids (IL) prepared using Lithium bis(trifluoromethyl sulfonyl)imide (LiTFSI) as salt, with premixed pyrrolidinium bis(trifluoromethyl sulfonyl)imide (PYR) as solvent and 1,3-dioxolane (DOL) as diluent were used to wet both SSE-electrode interfaces. The effect of IL dilution, co-solvent amount, LiTFSI concentration, C rate at which the batteries are tested and the effect of SSE inside the cathode, were systematically studied and optimized to develop a quasi-solid-state electrolyte Li-S battery (QSSLSB) with higher capacity retention and cyclability. LiTFSI (2M) dissolved in PYR:DOL(1:1) found to be optimum IL combination for low sulfur loading QSSLSBs reaching 500 mAh/g after 100 cycles while LiTFSI (3M) in PYR:DOL(1:3) was the optimum IL concentration for higher loading QSSLSBs reaching 400 mAh/g after 100 cycles. This work reports promising results of QSSLSB based on novel Li6PS5F0.5Cl0.5 Li-argyrodite solid-state electrolyte (SSE) with minute amount of IL, Super P-Sulfur (SP:S) cathode, and Li-anode. It also offers a new insight into the intimate interfacial contacts between the SSE and carbon-sulfur cathodes, which will be critical for improved electrochemical performance of quasi-solid-state lithium-sulfur batteries with high sulfur loading in the future.

25 ENERGY STORAGE↗
DOE OSTI2024

Halogen Thermochemistry Assessed with Density Functional Theory: Systematic Errors, Swift Corrections and Effects on Electrochemistry

Abstract Despite its sizable errors, density functional theory (DFT) is extensively used to evaluate thermochemical properties of gases, liquids and their interfaces with solids. As numerous halogen‐containing compounds appear as reactants, products and/or electrolytes in electrochemical reactions, and ionic effects are currently an active area of research, it is important to evaluate the accuracy of DFT for halogen thermochemistry. Herein, we assess the formation energies of interhalogens, hydrogen halides, diatomic and atomic halogens and their ions using six widespread functionals at the GGA, meta‐GGA and hybrid levels. We observe that DFT errors with respect to experiments are correlated with the electronegativity of the species and there are systematic trends across functionals, such that swift corrections were devised. Specifically, the average of the mean absolute errors for the six functionals decreased from 0.19 eV before the corrections to 0.08 eV after them. Besides, the overall maximum absolute error (MAX) decreased from 0.76 to 0.44 eV and the average of the MAXs decreased from 0.51 to 0.24 eV. Finally, we illustrate the qualitative and quantitative impact of gas‐phase errors on the predictions of surface Pourbaix diagrams.

Chemistry↗
DOE OSTI2026

Cathode-Confined Polysulfide Retention-Release Reprograms Li 2 S Deposition in High-Loading Li–S Batteries

High-loading lithium-sulfur (Li-S) cells operated with lean electrolyte are limited by polysulfide crossover to Li metal and by transport-limited liquid-solid conversion that forms passivating Li 2 S films. Here, we show that a cathode-facing separator coating of carboxylated multiwalled carbon nanotubes acts as a cathode-confined polysulfide reservoir with intermediate binding. Early in discharge it captures newly generated polysulfides at the separator interface, suppressing shuttle reactions. As polysulfides are consumed, the reservoir buffers concentration gradients and feeds reactants back to the cathode, shifting Li 2 S deposition from burst-like film growth to progressive, three-dimensional, porous formation. Synchrotron XRD and S K-edge XANES, together with Scharifker–Hills nucleation analysis and depth-of-discharge EIS/DRT, substantiate this coupled transport–reaction control. With 4.3 mg S cm -2 and E/S = 5, cells reach 4.2 mAh cm -2 and retain 90% capacity over 100 cycles at 20 °C.

25 ENERGY STORAGE↗
DOE OSTI2024

Atomic dynamics of electrified solid–liquid interfaces in liquid-cell TEM

Electrified solid–liquid interfaces (ESLIs) play a key role in various electrochemical processes relevant to energy, biology and geochemistry. The electron and mass transport at the electrified interfaces may result in structural modifications that markedly influence the reaction pathways. For example, electrocatalyst surface restructuring during reactions can substantially affect the catalysis mechanisms and reaction products. Despite its importance, direct probing the atomic dynamics of solid–liquid interfaces under electric biasing is challenging owing to the nature of being buried in liquid electrolytes and the limited spatial resolution of current techniques for in situ imaging through liquids. Here, with our development of advanced polymer electrochemical liquid cells for transmission electron microscopy (TEM), we are able to directly monitor the atomic dynamics of ESLIs during copper (Cu)-catalysed CO 2 electroreduction reactions (CO 2 ERs). Our observation reveals a fluctuating liquid-like amorphous interphase. It undergoes reversible crystalline–amorphous structural transformations and flows along the electrified Cu surface, thus mediating the crystalline Cu surface restructuring and mass loss through the interphase layer. Furthermore, the combination of real-time observation and theoretical calculations unveils an amorphization-mediated restructuring mechanism resulting from charge-activated surface reactions with the electrolyte. Our results open many opportunities to explore the atomic dynamics and its impact in broad systems involving ESLIs by taking advantage of the in situ imaging capability.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Solid State Ionics: Materials Development by Multiscale Modeling and Advanced Manufacturing Techniques

Solid-state ionic materials are an important enabling technology for energy conversion and storage. Solid-state batteries would be a safer and higher energy density alternative to commercially available lithium ion batteries (LIB), however their implementation requires ion conduction in solids at room temperature to occur on the same level as the current generation of liquid electrolytes. Microstructural modifications have been demonstrated to play a major role on ion transport through the control of grain boundary interfaces, which traditionally serve as “blocking” layers. Ultimately, these materials will be fabricated in thin films form as electrolytes in order to minimize ohmic losses in electrochemical devices. This work uses advanced manufacturing techniques in combination with theoretical modeling to implement a science-based approach in the deposition of thin films ion conductors with controlled microstructures used in ceramic energy conversion and storage devices.

25 ENERGY STORAGE↗
NASA NTRS1995

Studies on Methanol Crossover in Liquid-Feed Direct Methanol Pem Fuel Cells

The performance of liquid feed direct methanol fuel cells using various types of Nafion membranes as the solid polymer electrolyte have been studied. The rate of fuel crossover and electrical performance has been measured for cells with Nafion membranes of various thicknesses and equivalent weights. The crossover rate is found to decrease with increasing thickness and applied current. The dependence of crossover rate on current density can be understood in terms of a simple linear diffusion model which suggests that the crossover rate can be influenced by the electrode structure in addition to the membrane. The studies suggest that Nafion EW 1500 is a very promising alternate to Nafion EW 1100 for direct methanol fuel cells.

Methanol Pem Fuel↗
DOE OSTI2026

Plasticizer-Free Gradient-Crosslinked Polyurethane Electrolyte for Room-Temperature Solid-State Lithium Batteries

Polymer-based solid-state electrolytes are promising for next-generation lithium metal batteries, yet their limited ionic conductivity and mechanical stability at ambient conditions remain key challenges. Herein, we report a novel gradient crosslinked polymer electrolyte (PU/PUA/PU) synthesized via a sequential in situ UV-curing process that integrates a mechanically robust polyurethane acrylate (PUA) core with soft linear polyurethane (PU) interfaces. This all-solid membrane operates without any liquid plasticizer and the interfacial PU layers ensure low interfacial resistance and intimate electrode contact, while the PUA core provides enhanced dimensional stability and dendrite suppression. As a result, the gradient electrolyte delivers an impressive ∼2.6 × 10 −4 S cm −1 ionic conductivity at 25 °C (two orders of magnitude higher than conventional PEO) and remains electrochemically stable >5 V (vs Li + /Li). Structural analysis confirms the formation of a well-defined crosslinked network with suppressed crystallinity and expanded interchain spacing. Electrochemical impedance spectroscopy (EIS) and linear sweep voltammetry (LSV) further validate these properties. When applied in a Li||NMC811 cell, the PU/PUA/PU electrolyte delivers stable cycling with high capacity at both 60 °C and 25 °C, demonstrating its potential for room-temperature solid-state battery applications without reliance on plasticizers or heating. In conclusion, this gradient design offers a practical path toward ambient-condition operation of solid-state lithium batteries, providing a paradigm for overcoming the traditional trade-off between ionic conductivity and mechanical robustness.

25 ENERGY STORAGE↗
DOE OSTI2025

Electrochemical recovery of Gd into liquid Bi in molten LiCl-KCl-GdCl 3

The electrochemical recovery of Gd into liquid Bi electrodes was investigated in molten LiCl-KCl-GdCl 3 electrolyte at 773–973 K using constant currents of 10–150 mA cm −2 . High round-trip coulombic efficiency (>97 %) was demonstrated for deposition and removal of Gd into and from liquid Bi at all temperatures, confirming chemically reversible electrode reactions towards high recovery yield of Gd using liquid Bi. Furthermore, the overpotential associated with deposition of Gd into the liquid Bi electrode gradually increased with current density and decreased with temperature. At the lowest temperature of 773 K, a steep increase in overpotential was evident at high current densities due to slower mass transport and low solubility of Gd in liquid Bi (0.5 at.% Gd). Based on the impedance spectra of Bi electrodes at 773–973 K, the exchange current density was estimated to be 110–220 mA cm −2 , indicating facile charge transfer at the liquid electrode-electrolyte interface. Post-mortem characterization of Bi cathodes after electrolysis at 873 K indicated the formation of a solid GdBi(s) compound layer at the Bi electrode surface. Chemical analysis of Bi cathodes at various deposited Gd compositions resulted in Faradaic efficiencies of ∼75–84 %, promising a high recovery yield of Gd from molten salts using a strongly-interacting liquid Bi electrode.

36 - MATERIALS SCIENCE↗
DOE OSTI2021

Ion Pair Uptake in Ion Gel Devices Based on Organic Mixed Ionic–Electronic Conductors

Abstract In organic mixed ionic–electronic conductors (OMIECs), it is critical to understand the motion of ions in the electrolyte and OMIEC. Generally, the focus is on the movement of net charge during gating, and the motion of neutral anion–cation pairs is seldom considered. Uptake of mobile ion pairs by the semiconductor before electrochemical gating (passive uptake) can be advantageous as this can improve device speed, and both ions can participate in charge compensation during gating. Here, such passive ion pair uptake in high‐speed solid‐state devices is demonstrated using an ion gel electrolyte. This is compared to a polymerized ionic liquid (PIL) electrolyte to understand how ion pair uptake affects device characteristics. Using X‐ray photoelectron spectroscopy, the passive uptake of ion pairs from the ion gel into the OMIEC is detected, whereas no uptake is observed with a PIL electrolyte. This is corroborated by X‐ray scattering, which reveals morphological changes to the OMIEC from the uptake of ion pairs. With in situ Raman, a reorganization of both anions and cations is then observed during gating. Finally, the speed and retention of OMIEC‐based neuromorphic devices are tuned by controlling the freedom of charge motion in the electrolyte.

Quill, Tyler J.↗