Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “knot”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

A simplified flight-test method for determining aircraft takeoff performance that includes effects of pilot technique

A method for evaluating aircraft takeoff performance from brake release to air-phase height that requires fewer tests than conventionally required is evaluated with data for the XB-70 airplane. The method defines the effects of pilot technique on takeoff performance quantitatively, including the decrease in acceleration from drag due to lift. For a given takeoff weight and throttle setting, a single takeoff provides enough data to establish a standardizing relationship for the distance from brake release to any point where velocity is appropriate to rotation. The lower rotation rates penalized takeoff performance in terms of ground roll distance; the lowest observed rotation rate required a ground roll distance that was 19 percent longer than the highest. Rotations at the minimum rate also resulted in lift-off velocities that were approximately 5 knots lower than the highest rotation rate at any given lift-off distance.

Larson, T. J.↗
NASA NTRS1973

Estimation of peak winds from hourly observations

Two closely related methods to obtain estimates of the hourly peak wind at Cape Kennedy were compared by statistical tests. The methods evaluated the Monin-Obukhov stability length and the standard deviation of the hourly observed wind speed, so as to augment the latter quantity by F standard deviations. F is an optimized factor. A third method utilizing an optimized gust factor was also applied to the hourly wind. The latter procedure estimated 2952 peak winds with an rms error of 2.81 knots, an accuracy which was not surpassed by the other methods. Peak ground wind speed data were developed for use in space shuttle design operation analyses.

Graves, M. E.↗
NASA NTRS1974

Flight investigation of approach and flare from simulated breakout altitude of a subsonic jet transport and comparison with analytical models

Satisfactory and optimum flare windows are defined from pilot ratings and comments. Maximum flare normal accelerations, touchdown rates of sink, and total landing maneuver time increments are summarized as a function of approach airspeed margin (with respect to reference airspeed) and flare initiation altitude. The effects of two thrust management techniques are investigated. Comparisons are made with predictions from three analytical models and the results of a simulator study. The approach speed margin was found to have a greater influence on the flare initiation altitude than the absolute airspeed. The optimum airspeed was between the reference airspeed and the reference airspeed plus 10 knots. The optimum flare initiation altitude range for unrestricted landings was from 11 meters to 20 meters (36 feet to 66 feet), and the landing time in the optimum window was 8 seconds. The duration of the landing maneuver increased with increasing flare initiation altitude and with increasing speed margins on the approach.

Matheny, N. W.↗
NASA NTRS1974

Evaluation of graphite composite materials for bearingless helicopter rotor application

Small scale combined load fatigue tests were conducted on twelve unidirectional graphite-glass scrim-epoxy composite specimens. The specimens were 1 in. (2.54 cm) wide by 0.1 in. (.25 cm) thick by 5 in. (12.70 cm) long. The fatigue data was developed for the preliminary design of the spar for a bearingless helicopter main rotor. Three loading conditions were tested. Combinations of steady axial, vibratory torsion, and vibratory bending stresses were chosen to simulate the calculated stresses which exist at the root and at the outboard end of the pitch change section of the spar. Calculated loads for 150 knots (77.1 m/sec) level flight were chosen as the baseline condition. Test stresses were varied up to 4.4 times the baseline stress levels. Damage resulted in reduced stiffness; however, in no case was complete fracture of the specimen experienced.

Ulitchny, M. G.↗
NASA NTRS1973

Scale model testing of drogues for free drifting buoys

Instrumented model drogue tests were conducted in a ship model towing tank. The purpose of the tests was to observe and measure deployment and drag characteristics of such shapes as parachutes, crossed vanes, and window shades which may be employed in conjunction with free drifting buoys. Both Froude and Reynolds scaling laws were applied while scaling to full scale relative velocities of from 0 to 0.2 knots. A weighted window shade drogue is recommended because of its performance, high drag coefficient, simplicity, and low cost. Detailed theoretical performance curves are presented for parachutes, crossed vanes, and window shade drogues. Theoretical estimates of depth locking accuracy and buoy-induced dynamic loads pertinent to window shade drogues are presented as a design aid. An example of a window shade drogue design is presented.

Vachon, W. A.↗
NASA NTRS1974

Flyover noise characteristics of a tilt-wing V/STOL aircraft (XC-142A)

A field noise measurement investigation was conducted during the flight testing of an XC-142A tilt-wing V/STOL aircraft to define its external noise characteristics. Measured time histories of overall sound pressure level show that noise levels are higher at lower airspeeds and decrease with increased speed up to approximately 160 knots. The primary noise sources were the four high-speed, main propellers. Flyover-noise time histories calculated by existing techniques for propeller noise prediction are in reasonable agreement with the experimental data.

Pegg, R. J.↗
NASA NTRS1974

A flight investigation with a STOL airplane flying curved, descending instrument approach paths

A flight investigation using a De Havilland Twin Otter airplane was conducted to determine the configurations of curved, 6 deg descending approach paths which would provide minimum airspace usage within the requirements for acceptable commercial STOL airplane operations. Path configurations with turns of 90 deg, 135 deg, and 180 deg were studied; the approach airspeed was 75 knots. The length of the segment prior to turn, the turn radius, and the length of the final approach segment were varied. The relationship of the acceptable path configurations to the proposed microwave landing system azimuth coverage requirements was examined.

Benner, M. S.↗
NASA NTRS1974

The results of a low-speed wind tunnel test to investigate the effects of the Refan JT8D engine target thrust reverser on the stability and control characteristics of the Boeing 727-200 airplane

The effects of the Refan JT8D side engine target thrust reverser on the stability and control characteristics of the Boeing 727-200 airplane were investigated using the Boeing-Vertol 20 x 20 ft Low-Speed Wind Tunnel. A powered model of the 727-200 was tested in groud effect in the landing configuration. The Refan target reverser configuration was evaluated relative to the basic production 727 airplane with its clamshell-deflector door thrust reverser design. The Refan configuration had slightly improved directional control characteristics relative to the basic airplane. Clocking the Refan thrust reversers 20 degrees outboard to direct the reverser flow away from the vertical tail, had little effect on directional control. However, clocking them 20 degrees inboard resulted in a complete loss of rudder effectiveness for speeds greater than 90 knots. Variations in Refan reverser lip/fence geometry had a minor effect on directional control.

Kupcis, E. A.↗
NASA NTRS1974

A wind-tunnel investigation of parameters affecting helicopter directional control at low speeds in ground effect

An investigation was conducted in the Langley full-scale tunnel to measure the performance of several helicopter tail-rotor/fin configurations with regard to directional control problems encountered at low speeds in ground effect. Tests were conducted at wind azimuths of 0 deg to 360 deg in increments of 30 deg and 60 deg and at wind speeds from 0 to 35 knots. The results indicate that at certain combinations of wind speed and wind azimuth, large increases in adverse fin force require correspondingly large increases in the tail-rotor thrust, collective pitch, and power required to maintain yaw trim. Changing the tail-rotor direction of rotation to top blade aft for either a pusher tail rotor (tail-rotor wake blowing away from fin) or a tractor tail rotor (tail-rotor wake blowing against fin) will alleviate this problem. For a pusher tail rotor at 180 deg wind azimuth, increases in the fin/tail-rotor gap were not found to have any significant influence on the overall vehicle directional control capability. Changing the tail rotor to a higher position was found to improve tail-rotor performance for a fin-off configuration at a wind azimuth of 180 deg. A V-tail configuration with a pusher tail rotor with top blade aft direction of rotation was found to be the best configuration with regard to overall directional control capability.

Yeager, W. T., Jr.↗
NASA NTRS1974

Measurement and analysis of aircraft far-field aerodynamic noise

A systematic investigation of aircraft far-field radiated, aerodynamically generated noise was conducted. The test phase of the original program involved the measurement of the noise produced by five gliding aircraft in an aerodynamically clean configuration during low altitude flyovers. These aircraft had gross weights that ranged from 5785 to 173 925N (1300 to 39,000 pounds), fly-by velocities from 30 to 98.5m/sec (58 to 191.5 knots or 98 to 323 ft/sec) and wing aspect ratios from 6.59 to 18.25. The results of these measurements were used to develop an equation relating aerodynamic noise to readily evaluated physical and operational parameters of the aircraft. A non-dimensional frequency spectrum, based on the mean wing thickness, was also developed.

Healy, G. J.↗
NASA NTRS1974

Experimental investigation of the cornering characteristics of 18 by 5.5, type 7, aircraft tires with different tread patterns

The characteristics, which include the cornering-force and drag-force friction coefficients and self-alining torque, were obtained on dry, damp, and flooded runway surfaces over a range of yaw angles from 0 deg to 12 deg and at ground speeds from approximately 5 to 90 knots. The results indicate that a tread pattern with pinholes in the ribs reduces the tire cornering capability at high yaw angles on a damp surface but improves cornering on a dry surface. A tread pattern which has transverse grooves across the entire width of the tread improves the tire cornering performance slightly at high speeds on the flooded runway surface. The cornering capability of all the tires is degraded at high ground speeds by thin film lubrication and/or tire hydroplaning effects. Alterations to the conventional tread pattern provide only marginal improvements in the tire cornering capability which suggests that runway surface treatments may be a more effective way of improving aircraft ground performance during wet operations.

Dreher, R. C.↗
NASA NTRS1974

Measurement of tilt rotor VTOL rotor wake-airframe ground aerodynamic interference for application to real time flight simulation

The hover and low speed rotor wake-airframe-ground aerodynamic characteristics of the XV-15 tilt rotor research aircraft were determined in wind tunnel tests of a scale model. Results of the wind tunnel tests were applied to real flight time simulation. The principal findings of the wind tunnel tests are summarized. The effect of aerodynamic interference on the handling qualities of the aircraft is analyzed. It was determined that aerodynamic interference effects are significant in hover and at low speeds, with the influence being more pronounced in ground effect than out of it. At airspeeds above 60 knots, aerodynamic interference does not have a significant effect on handling characteristics.

Gaffey, T. M.↗
NASA NTRS1974

A simplified package for calculating with splines

This package is designed to solve some of the elementary problems of spline interpretation and least squares fit. The subroutines fall into three basic categories. The first category involves computations with a given spline and/or knot sequence; the second category involves routines which calculate the coefficients of splines which perform a certain task (such as interpolation or least squares fit); and the last category is a banded equation solver for specific linear equations.

Smith, P. W.↗
NASA NTRS1975

The spectral energy distribution of NGC 1275

An analysis of absolute spectral energy distributions of interstellar gas for a galaxy (NGC 1275) is presented. Infrared spectra data shows heavy reddening. It is proposed that the interstellar gas may be ionized by shock waves or by nonthermal or stellar radiation. It is suggested, that high velocity, emission-line knots are H2 regions in a Perseus cluster galaxy or intergalactic gas cloud seen in projection against NGC 1275.

Shields, G. A.↗
NASA NTRS1974

Engineering simulation evaluation of the two-segment noise abatement approach in the Douglas DC-8-61

The development and operational evaluation are discussed of a noise abatement two-segment approach which is safe and operationally acceptable for routine use in air carrier service. An engineering simulation evaluation was conducted; it was found that the entry speed and initial configuration are more important in the DC-8-61 than in the 727 because of the DC-8's aerodynamic cleanliness and drag programming constraints. It was also found that the altitude required for the DC-8 upper and lower transitions is less than the 727 transitions principally due to the pitching moment from the underslung DC-8 engines as compared to the 727 engines which produce no pitching moment with a change in thrust. The 727 approach was a reduced flaps (30 degrees) procedure with a 10-knot airspeed bleed in the lower transition; the DC-8 approach is a full flaps (50 degrees) procedure with constant airspeed established as soon as possible after upper segment transition.

Nylen, W. E.↗
NASA NTRS1975

Motion-base simulator study of control of an externally blown flap STOL transport aircraft after failure of an outboard engine during landing approach

A moving-base simulator investigation of the problems of recovery and landing of a STOL aircraft after failure of an outboard engine during final approach was made. The approaches were made at 75 knots along a 6 deg glide slope. The engine was failed at low altitude and the option to go around was not allowed. The aircraft was simulated with each of three control systems, and it had four high-bypass-ratio fan-jet engines exhausting against large triple-slotted wing flaps to produce additional lift. A virtual-image out-the-window television display of a simulated STOL airport was operating during part of the investigation. Also, a simple heads-up flight director display superimposed on the airport landing scene was used by the pilots to make some of the recoveries following an engine failure. The results of the study indicated that the variation in visual cues and/or motion cues had little effect on the outcome of a recovery, but they did have some effect on the pilot's response and control patterns.

Middleton, D. B.↗
NASA NTRS1975

Simulator evaluation of a perspective clipped-pole display and a thrust-vector controller for VTOL zero-zero landings

Five pilots participated in a simulator study to evaluate design features of a perspective clipped pole display and a side arm thrust vector controller for potential applications to VTOL zero visibility landings. Analyses of objective measures by a t test for related means showed significant learning effects, but did not show significant performance differences among display conditions. A mean longitudinal touchdown velocity of less than 4 knots, a mean vertical touchdown velocity of less than 1.22m/sec, and a mean longitudinal position error of approximately 15.24 m were attained during the final 10 trials of the experiment. The conclusion that adequate airspeed and altitude cues could be obtained from the glideslope and runway poles is supported by the absence of significant performance differences among display conditions.

Murphy, M. R.↗
NASA NTRS1975

The inversion of aureole measurements to derive aerosol size distributions

An iterative method to invert size distributions from simulated scattered radiance measurements at small angles from the sun has been investigated. The inferred size distributions were represented by piecewise linear and cubic spline functions. Various relevant characteristics were investigated and it was found that: (1) the inverted size distribution was insensitive to the number of knots in the piecewise linear spline; (2) within the range of sensitivity, the choice of initial guess had little effect on the inverted size distribution; (3) five per cent random noise in the simulated radiances appreciably deteriorated the result but variations are still tolerable when compared with other methods for determining size distributions; (4) the inverted distribution was insensitive to the index of refraction used in the kernel for particle radii greater than 1 micron; (5) the choice of wavelength between 0.40 and 0.70 microns has a negligible effect on the inverted distribution; (6) a range of tropospheric aerosol size distributions gives acceptable inverted results; and (7) the cubic spline representation can give reasonable inverted distributions, but may become unstable.

Twitty, J. T.↗