Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “interval analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Green corona and solar sector structure

Analysis of the green-line corona for the interval 1947-1970 suggests the existence of large-scale organization of the emission. The green-line emission at high northern latitudes (approximately 40 to 60 deg) is correlated with the emission at high southern latitudes 6, 15, and 24 days later, while the low-latitude green corona seems to be correlated on both sides of the equator with no time lag. These coronal features are recurrent with a 27-day period at all latitudes between plus or minus 60 deg, and these large-scale structures are believed to be associated with the solar magnetic sector structure. The high correlation between northern and southern high-latitude emission at 15 days time lag is explained as a signature of a two-sector structure, while four sectors are associated with the 6- and 24-day peaks.

Antonucci, E.↗
NASA NTRS1977

Reliability measurement during software development

Measurement of software reliability was carried out during the development of data base software for a multi-sensor tracking system. Every run made during this project was scored as success or failure, and supporting data were collected on forms for further analysis. The failure ratio (number of failures per calendar interval divided by total number of runs) and failure rate (number of failures divided by CPU time for the interval) were found to be consistent measures, on a month-to-month basis as well as from module to module, and therefore considered valid indicators of reliability in this environment. Trend lines could be established from these measurements that provide good visualization of the progress on the job as a whole as well as on individual modules. Over one-half of the observed failures were due to factors associated with the specific run submission rather than with the code proper.

Hecht, H.↗
NASA NTRS1978

Simultaneous observations of equatorial ionospheric scintillation on four frequencies

The variation with frequency of ionospheric scintillations, simultaneously observed at 40, 140, 360, and 860 MHz at equatorial latitudes, was studied. The ATS 6 geostationary satellite was equipped with radio beacons at 40, 140, and 360 MHz, and also with a television downlink at 860 MHz. The signals were recorded at Ootacamund, India (dip 4 deg N) and were most common between 2000 and 2300 LT. It was found that the spectral index of an expression used by Aarons et al (1967) was not constant but decreased with increasing magnitude of scintillations. For weak scintillations the spectral index (referred to as the exponent) was found to be close to 1.0. The analysis of the records involved scaling at 15-sec intervals and the calculation of the average scintillation index.

Rastogi, R. G.↗
NASA NTRS1985

Identification of atmospheric C2H2 lines in the 3230-3340/cm region of high resolution solar absorption spectra recorded at the National Solar Observatory

A search has been conducted for the presence of absorption lines of atmospheric acetylene (C2H2), taking into account the 3230-3340/cm interval of 0.01/cm resolution solar absorption spectra recorded with the interferometer of the Solar Observatory on Kitt Peak. A total of 12 lines belonging to the strong nu-3 and nu-2 + nu-4 + nu-5 bands has been identified in this interval. This letter provides a report regarding the identification analysis of selected atmospheric C2H2 lines in a representative set of Kitt Peak solar spectra.

Rinsland, C. P.↗
NASA NTRS1988

Faunal and erosional events in the Eastern Tethyan Sea across the K/T boundary

A regional pattern of three closely spaced erosional events at and above the K/T boundary was determined from six Cretaceous/Tertiary boundary sections in the Negev of Israel. The sections were collected from locations throughout the central and northern Negev. All sections are lithologically similar. The Maastrichtian consists of a sequence of limestone beds intercalated with thin marly beds. In some sections, the last limestone bed is followed by 1 to 2 m of calcareous marls grading upwards into several meters of grey shale. In other sections the limestone bed is followed directly by grey shale with the contact containing particles of limestone and marl. A 5 to 20 cm thick dark grey organic-rich clay layer is present about 1.5 to 2.5 m above the base of the grey shale. The grey shale grades upwards into increasingly carbonate rich marls. No unconformities are apparent in field outcrops. During field collection the dark grey clay layer was believed to represent the K/T boundary clay. Microfossil analysis however identified the boundary at the base of the grey shale. The black shale represents a low productivity anoxic event similar to, but younger than, the K/T boundary clay in other K/T boundary sections. High resolution planktic foraminiferal and carbonate analysis of these sections (at 5 to 10 cm intervals) yield surprising results. The K/T boundary is marked by an erosional event which removed part or all of the uppermost Maastrichtian marls above the last limestone bed. Percent carbonate data for four Negev sections are illustrated and show the regional similarities in carbonate sedimentation. Faunal and carbonate data from the Negev sections thus show three closely spaced short erosional events at the K/T boundary and within the first 50,000 to 100,000 years of the Danian. These K/T boundary erosional events may represent global climatic or paleoceanographic events.

Keller, G.↗
NASA NTRS1992

Venus radar mapping from the Venera 15 and 16 spacecrafts: Results and restrictions

A description of the results of the Venus northern hemisphere radar survey in 1983-1984 from the Venera 15 and 16 spacecrafts is presented. In addition, we discuss some peculiarities in the function of the radar equipment that defined the technology of SAR data processing. Among these peculiarities are insufficient calibration of SAR and radar altimeter and erroneous automatic gain control data transmission from the spacecrafts. As a result, the procedure of image synthesis and mosaicking contained multistage image brightness corrections. This led to the fact that the average image brightness in a spot 100 km in diameter was constant everywhere in the mosaics. Twenty-seven radar mosaics in the Lambert-Hauss conic projection with 1-2 km spatial resolution covering 25 percent of the surface of Venus have been produced. A Venus surface roughness map was constructed by joint processing of SAR and altimeter data. The mutual calibration of the SAR and altimeter was made in the special radar session when the SAR and altimeter were declined from the local vertical at the same angle. The possibility of estimating relative variations in surface reflection properties over a tens-of-kilometers interval from Venera images is still being considered. Joint analysis of the coordinates of small features of the Venera and Magellan images is one more approach being used to refine the period of rotation for Venus.

Akim, E. L.↗
NASA NTRS2009

A Landsat-Based Assessment of Mobile Bay Land Use and Land Cover Change from 1974 to 2008

The Mobile Bay region has experienced noteworthy land use and land cover (LULC) change in the latter half of the 20th century. Accompanying this change has been urban expansion and a reduction of rural land uses. Much of this LULC change has reportedly occurred since the landfall of Hurricane Frederic in 1979. The Mobile Bay region provides great economic and ecologic benefits to the Nation, including important coastal habitat for a broad diversity of fisheries and wildlife. Regional urbanization threatens the estuary s water quality and aquatic-habitat dependent biota, including commercial fisheries and avian wildlife. Coastal conservation and urban land use planners require additional information on historical LULC change to support coastal habitat restoration and resiliency management efforts. This presentation discusses results of a Gulf of Mexico Application Pilot project that was conducted in 2008 to quantify and assess LULC change from 1974 to 2008. This project was led by NASA Stennis Space Center and involved multiple Gulf of Mexico Alliance (GOMA) partners, including the Mobile Bay National Estuary Program (NEP), the U.S. Army Corps of Engineers, the National Oceanic and Atmospheric Administration s (NOAA s) National Coastal Data Development Center (NCDDC), and the NOAA Coastal Services Center. Nine Landsat images were employed to compute LULC products because of their availability and suitability for the application. The project also used Landsat-based national LULC products, including coastal LULC products from NOAA s Coastal Change & Analysis Program (C-CAP), available at 5-year intervals since 1995. Our study was initiated in part because C-CAP LULC products were not available to assess the region s urbanization prior to 1995 and subsequent to post Hurricane Katrina in 2006. This project assessed LULC change across the 34-year time frame and at decadal and middecadal scales. The study area included the majority of Mobile and Baldwin counties that encompass Mobile Bay. In doing so, each date of Landsat data was classified using an end-user defined modified Anderson level 1 classification scheme. LULC classifications were refined using a decision rule approach in conjunction with available C-CAP products. Individual dates of LULC classifications were validated by image interpretation of stratified random locations on raw Landsat color composite imagery in combination with higher resolution remote sensing and in-situ reference data. The results indicate that during the 34-year study period, urban areas increased from 96,688 to 150,227 acres, representing a 55.37% increase, or 1.63% per annum. Most of the identified urban expansion results from conversion of rural forest and agriculture to urban cover types. Final LULC mapping and metadata products were produced for the entire study area as well as watersheds of concern within the study area. Final project products, including LULC trend information, were incorporated into the Mobile Bay NEP State of the Bay report. Products and metadata were transferred to NOAA NCDDC to allow free online accessibility and use by GOMA partners and by the public.

Spruce, Joseph↗
NASA NTRS2019

Computational Bayesian Methods Applied to Complex Problems in Bio and Astro Statistics

In this dissertation we apply computational Bayesian methods to three distinct problems. In the first chapter, we address the issue of unrealistic covariance matrices used to estimate collision probabilities. We model covariance matrices with a Bayesian Normal-Inverse-Wishart model, which we fit with Gibbs sampling. In the second chapter, we are interested in determining the sample sizes necessary to achieve a particular interval width and establish non-inferiority in the analysis of prevalences using two fallible tests. To this end, we use a third order asymptotic approximation. In the third chapter, we wish to synthesize evidence across multiple domains in measurements taken longitudinally across time, featuring a substantial amount of structurally missing data, and fit the model with Hamiltonian Monte Carlo in a simulation to analyze how estimates of a parameter of interest change across sample sizes.

Elrod, Chris↗
NASA NTRS2008

Uncertainty and Sensitivity Analyses of a Two-Parameter Impedance Prediction Model

This paper presents comparisons of predicted impedance uncertainty limits derived from Monte-Carlo-type simulations with a Two-Parameter (TP) impedance prediction model and measured impedance uncertainty limits based on multiple tests acquired in NASA Langley test rigs. These predicted and measured impedance uncertainty limits are used to evaluate the effects of simultaneous randomization of each input parameter for the impedance prediction and measurement processes. A sensitivity analysis is then used to further evaluate the TP prediction model by varying its input parameters on an individual basis. The variation imposed on the input parameters is based on measurements conducted with multiple tests in the NASA Langley normal incidence and grazing incidence impedance tubes; thus, the input parameters are assigned uncertainties commensurate with those of the measured data. These same measured data are used with the NASA Langley impedance measurement (eduction) processes to determine the corresponding measured impedance uncertainty limits, such that the predicted and measured impedance uncertainty limits (95% confidence intervals) can be compared. The measured reactance 95% confidence intervals encompass the corresponding predicted reactance confidence intervals over the frequency range of interest. The same is true for the confidence intervals of the measured and predicted resistance at near-resonance frequencies, but the predicted resistance confidence intervals are lower than the measured resistance confidence intervals (no overlap) at frequencies away from resonance. A sensitivity analysis indicates the discharge coefficient uncertainty is the major contributor to uncertainty in the predicted impedances for the perforate-over-honeycomb liner used in this study. This insight regarding the relative importance of each input parameter will be used to guide the design of experiments with test rigs currently being brought on-line at NASA Langley.

Jones, M. G.↗
DOE OSTI2022

Decay Curve Correction Analysis Report

The decay curve analysis that is done on the short-lived radionuclide gas samples is used to differentiate between gaseous radionuclides that have the same characteristic gamma decay energy, 511 kiloelectron-volts (keV). A sample of stack gas is isolated and the total counts in the 511 keV peak are counted repeatedly in 10-second intervals to evaluate the decay rate of the sample over time. Analysis of this decay data required a series of steps. First, a raw data report is generated by the gamma acquisition system, based on an analysis template within the acquisition software. The data report file was then loaded into Microsoft Word, and a macro was used to perform minor formatting (remove colons and insert tabs between data columns) to allow analysis within Excel. The file is then saved as a text file at this point. The text file is then uploaded into Excel and a series of macros are used to add labels, calculate radioactive decay constants, and analyze the gamma decay data using linear regression techniques. The analysis template has been used since 1998 for stack 53000303 (TA-53, building 0003, exhaust stack 03) and 2000 for stack 53000702. The overall process, including the gamma report format and the macros used in Word and Excel for processing the report, had remained unchanged until 2015. In October of 2015, staff made a change to the report template in the gamma acquisition software which resulted in an error in the calculations later performed by the Excel macro. This error was not caught until a more in-depth review of the analysis took place regarding 2020 data. This report covers a much more complete review of the issue that occurred regarding the decay curve analysis, a review of the calculations completed to correct the issue, a review of the updated decay curve analysis process, and recommendations for moving forward.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
NASA NTRS2016

Modeling Relationships Between Flight Crew Demographics and Perceptions of Interval Management

The Interval Management Alternative Clearances (IMAC) human-in-the-loop simulation experiment was conducted to assess interval management system performance and participants' acceptability and workload while performing three interval management clearance types. Twenty-four subject pilots and eight subject controllers flew ten high-density arrival scenarios into Denver International Airport during two weeks of data collection. This analysis examined the possible relationships between subject pilot demographics on reported perceptions of interval management in IMAC. Multiple linear regression models were created with a new software tool to predict subject pilot questionnaire item responses from demographic information. General patterns were noted across models that may indicate flight crew demographics influence perceptions of interval management.

Remy, Benjamin↗
NASA NTRS2005

Probabilistic Parameter Uncertainty Analysis of Single Input Single Output Control Systems

The current standards for handling uncertainty in control systems use interval bounds for definition of the uncertain parameters. This approach gives no information about the likelihood of system performance, but simply gives the response bounds. When used in design, current methods of m-analysis and can lead to overly conservative controller design. With these methods, worst case conditions are weighted equally with the most likely conditions. This research explores a unique approach for probabilistic analysis of control systems. Current reliability methods are examined showing the strong areas of each in handling probability. A hybrid method is developed using these reliability tools for efficiently propagating probabilistic uncertainty through classical control analysis problems. The method developed is applied to classical response analysis as well as analysis methods that explore the effects of the uncertain parameters on stability and performance metrics. The benefits of using this hybrid approach for calculating the mean and variance of responses cumulative distribution functions are shown. Results of the probabilistic analysis of a missile pitch control system, and a non-collocated mass spring system, show the added information provided by this hybrid analysis.

Smith, Brett A.↗
NASA NTRS1972

Some characteristics of low-frequency oscillations observed at ATS 1.

Analysis of low-frequency oscillations of the magnetic field at ATS 1 for the 25-month data interval from December 1966 to December 1968. Irregular oscillations and oscillations associated with magnetic storms were excluded from the analysis. Of the 222 events identified, 170 events were oscillating predominantly transverse to the background magnetic field. The oscillations were observed to occur most frequently in the early afternoon hours. They also seemed to occur more frequently during December, January, and February than at other times of the year. During a given individual event the frequency was fairly constant and it varied between .0015 and .02 Hz with a broad peak near .01 Hz. The event duration varied between a minimum of 10 min and a maximum of 14 hours and 26 min. During a given event the amplitude varied. The average maximum amplitude of an event was about 3 gamma.

Cummings, W. D.↗
NASA NTRS1993

Tidal winds at mesopause altitudes over Arecibo (18 deg N, 67 deg W), 5-11 April 1989 (AIDA '89)

A tidal analysis of the imaging Doppler interferometer scattering point parameter data at upper mesosphere-lower thermosphere altitudes (70-110 km) is presented, on the basis of the procedure developed by Groves (1959), over the interval April 5-11, 1989 at Aercibo as part of Project AIDA. This analysis reveals a typical equatorial easterly circulation, with mean meridional circulation becoming significant only above 96 km. A periodogram analysis shows the diurnal tide to be the most significant feature of the wind field at these altitudes, with zonal amplitudes up to some 50 m/s and meridional amplitudes approximately half this value. The semidiurnal tide is well developed in both zonal and meridional directions only above 96 km. Both 8- and 6-hr components become significant above 100 km, the 6-h component being as strong as both the 24- and 12-h tides at 100 km.

Roper, R. G.↗
DOE OSTI2023

Wave Detection and Tracking Within a Rotating Detonation Engine Through Object Detection

As the operational time window of experimental rotating detonation engines (RDEs) is expanded and the technology matures toward integration within gas turbines, monitoring techniques must evolve to offer computationally efficient and highly time-resolved diagnostics. In this study, computer vision object detection methodology that seeks to reduce data processing time and calculate wave velocity within drastically reduced time intervals as compared to traditional high-frame-rate RDE images analysis techniques is proposed. The adapted you-only-look-once object detection network is trained to detect individual detonation waves within single down-axis RDE images. The wave location and rotational direction detected within a frame are tracked through a series of high-speed images to calculate the frame-to-frame wave velocity with the time-step resolution of $\mathrm{20 μs}$ across a series of frames. The analysis of the annotation box size and image linearization effects is presented, demonstrating the lowest frame-to-frame velocity total uncertainty of $\mathrm{±3.8\%}$ and the highest classification speed of 9.5 frames per second using linearized images. Linearized images “unwrap” the RDE annulus pixel region to a reduced image size. Here, this new method offers great reductions in data processing times and unsteady detonation behavior insight at intervals more comparable to the timescales of detonation wave interactions via the application of machine learning to experimental RDE data.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2022

Alternate Analysis of an In Vitro Solubility Study on the Lung Dissolution Rate of 238PuO2 Material Involved in the 2020 Incident at Los Alamos National Laboratory

Here this work presents an alternate analysis of an in vitro solubility study on the lung dissolution rate of 238 PuO 2 material involved in a recent inhalation incident at Los Alamos National Laboratory (LANL). The original dataset used in this work was retrieved from a recently published report. The present work shows an analysis of the same dataset by modeling the dissolution in separate time intervals rather than modeling the cumulative dissolution.

238Pu↗
DOE OSTI2022

Past fires and post-fire impacts reconstructed from a southwest Australian stalagmite

Speleothem records of past environmental change provide an important opportunity to explore fire frequency and intensity in the past, and the antecedent climatic conditions leading to fire events. Here, fire sensitive geochemical signals in a stalagmite from Yonderup Cave, a shallow cave in Western Australia, are compared to well-documented wildfire events that occurred in recent decades. The results are extended to identify wildfires during the growth interval of the speleothem (1760 CE–2005 CE). Principal component analysis of the stalagmite time-series revealed distinct peaks in a combination of phosphorus and metal (aluminium, zinc, copper and lead) concentrations in response to known fire events, which are interpreted to have come from ash. Varying responses in the geochemical signal in the pre- and post-European colonisation period are likely linked to changes in land management, fire frequency and fire intensities. Of note is what we infer to be a particularly intense fire event concluded to have occurred in 1897 ± 5 CE, which climate sensitive proxies (δ18O and bedrock-derived elements) indicate was preceded by a multi-decadal dry period that began in the late 1860s. The intensity of the deduced fire event is supported by a peak in P that is 6.3 times higher than elsewhere in the speleothem, accompanied by a peak in Zn. It was also inferred that changes to the surface-cave hydrology occurred as a result of this event, indicated by increased input of colloidal organic material onto the stalagmite that was interpreted to be caused by shallow karst bedrock fracturing from the heat-induced deformation that is observed after intense fires. These findings show the potential for speleothems to provide dated records of fire intensity and recurrence intervals. Further development could lead to a better understanding of the climate-fire relationship and the effects of land-management practices on wildfire frequency and intensity.

58 GEOSCIENCES↗
NASA NTRS2001

Respiratory modulation of human autonomic rhythms

We studied the influence of three types of breathing [spontaneous, frequency controlled (0.25 Hz), and hyperventilation with 100% oxygen] and apnea on R-R interval, photoplethysmographic arterial pressure, and muscle sympathetic rhythms in nine healthy young adults. We integrated fast Fourier transform power spectra over low (0.05-0.15 Hz) and respiratory (0.15-0.3 Hz) frequencies; estimated vagal baroreceptor-cardiac reflex gain at low frequencies with cross-spectral techniques; and used partial coherence analysis to remove the influence of breathing from the R-R interval, systolic pressure, and muscle sympathetic nerve spectra. Coherence among signals varied as functions of both frequency and time. Partialization abolished the coherence among these signals at respiratory but not at low frequencies. The mode of breathing did not influence low-frequency oscillations, and they persisted during apnea. Our study documents the independence of low-frequency rhythms from respiratory activity and suggests that the close correlations that may exist among arterial pressures, R-R intervals, and muscle sympathetic nerve activity at respiratory frequencies result from the influence of respiration on these measures rather than from arterial baroreflex physiology. Most importantly, our results indicate that correlations among autonomic and hemodynamic rhythms vary over time and frequency, and, thus, are facultative rather than fixed.

Non-NASA Center↗