Results for “interface converter” — Page 15

NASA NTRS2018

NASA Low Power Stirling Convertor for Small Landers, Probes, and Rovers Operating in Darkness

A variety of mission concepts have been studied by NASA and the U. S. Department of Energy that would utilize low power Radioisotope Power Systems (RPS) for probes, landers rovers, and repeaters. These missions would contain science instruments distributed across planetary surfaces or near objects of interest where solar flux is insufficient for using solar cells. Landers could be used to provide data like radiation, temperature, pressure, seismic activity, and other surface measurements for planetary science and to inform future mission planners. The studies proposed using fractional versions of the General Purpose Heat Source (GPHS) or multiple Light Weight Radioisotope Heater Units (LWRHU) to heat power conversion technologies for science instruments and communication. Dynamic power systems are capable of higher conversion efficiencies, which could enable equal power using less fuel or more power using equal fuel, when compared to less efficient static power conversion technologies. Providing spacecraft with more power would decrease duty cycling of basic functions and, therefore, increase the quality and abundance of science data. Low power Stirling convertors are being developed at NASA Glenn Research Center (GRC) to provide future micro spacecraft with electrical power by converting heat from one or more LWRHUs. An initial design converts multiple watts of heat to one watt of electrical power output using a Stirling convertor. Development of the concept includes maturation of convertor and controller designs, performance evaluation of an evacuated metal foil insulation, and development of system interfaces. Demonstration of the convertor is planned and represents a new class of RPS with power levels an order of magnitude lower than previous practical designs.

Wilson, Scott D.↗

NASA NTRS2018

NASA Low-Power Stirling Convertor for Small Landers, Probes, and Rovers Operating in Darkness

A variety of mission concepts have been studied by NASA and the U. S. Department of Energy that would utilize low power Radioisotope Power Systems (RPS) for landers, probes, and rovers. These missions would contain science measuring instruments distributed across planetary surfaces or near objects of interest where solar flux is insufficient for using solar cells. Landers could be used to provide data like wind, temperature, pressure, seismic activity, and other planetary measurements to mission planners or future explorers. The studies proposed using fractional versions of the General Purpose Heat Source (GPHS) or multiple Light Weight Radioisotope Heater Units (LWRHU) to heat power conversion technologies for science instruments and communication. Dynamic power systems are capable of higher conversion efficiencies, which could enable equal power using less fuel or more power using equal fuel, when compared to less efficient static power conversion technologies. Providing spacecraft with more power would decrease duty cycling of basic functions and, therefore, increase the quality and abundance of science data. Low power Stirling convertors are being developed at NASA Glenn Research Center (GRC) to provide future micro spacecraft with electrical power by converting heat from one or more LWRHUs. An initial design converts multiple Watts of heat to one Watt of electrical power output using a Stirling convertor. Development of the concept includes maturation of convertor and controller designs, performance evaluation of an evacuated metal foil insulation, and development of system interfaces.

Wilson, Scott D.↗

NASA NTRS2018

NASA Low Power Stirling Convertor for Small Landers, Probes, and Rovers Operating in Darkness

A variety of mission concepts have been studied by NASA and the U. S. Department of Energy that would utilize low power Radioisotope Power Systems (RPS) for landers, probes, and rovers. These missions would contain science measuring instruments distributed across planetary surfaces or near objects of interest where solar flux is insufficient for using solar cells. Landers could be used to provide data like wind, temperature, pressure, seismic activity, and other planetary measurements to mission planners or future explorers. The studies proposed using fractional versions of the General Purpose Heat Source (GPHS) or multiple Light Weight Radioisotope Heater Units (LWRHU) to heat power conversion technologies for science instruments and communication. Dynamic power systems are capable of higher conversion efficiencies, which could enable equal power using less fuel or more power using equal fuel, when compared to less efficient static power conversion technologies. Providing spacecraft with more power would decrease duty cycling of basic functions and, therefore, increase the quality and abundance of science data. Low power Stirling convertors are being developed at NASA Glenn Research Center (GRC) to provide future micro spacecraft with electrical power by converting heat from one or more LWRHUs. An initial design converts multiple Watts of heat to one Watt of electrical power output using a Stirling convertor. Development of the concept includes maturation of convertor and controller designs, performance evaluation of an evacuated metal foil insulation, and development of system interfaces.

Wilson, Scott↗

NASA NTRS1977

Engineering study of the module/array interface for large terrestrial photovoltaic arrays

Three major areas--structural, electrical, and maintenance--were evaluated. Efforts in the structural area included establishing acceptance criteria for materials and members, determining loading criteria, and analyzing glass modules in various framing system configurations. Array support structure design was addressed briefly. Electrical considerations included evaluation of module characteristics, intermodule connectors, array wiring, converters and lightning protection. Plant maintenance features such as array cleaning, failure detection, and module installation and replacement were addressed.

Source record↗

NASA NTRS2019

Prenatal 2g Exposure Alters Placental Expression of Stress-Related Genes

Extra-terrestrial colonization is of growing interest to space agencies and private entities, emphasizing the importance of research on reproduction and development in the absence of Earth's 1G. Maternal stressors can modify offspring development, exerting significant lifespan and crossgenerational changes through prenatal programming. The space environment is stressful, therefore exposure to altered gravity during pregnancy may impact later life outcomes in offspring. In ground-based studies, we exposed pregnant rats to continuous +G (above Earth gravity), and observed overweight and elevated anxiety in adult male (but not female) offspring, common phenotypes associated with prenatal maternal stress. Here we hypothesize that exposure to increased gravity during pregnancy elicits changes in the expression of stress-related genes in placenta that may mediate emergence of later life outcomes. While the placenta transports maternal factors to the fetus and produces endogenous fetal hormones, stress-induced changes at the placental-uterine interface may also alter communication between mother and fetus, facilitating prenatal transmission of unfavorable later life outcomes and cross-generational epigenetic alterations. Maternal stress elevates maternal glucocorticoids however placental 11b-hydroxysteroid dehydrogenase type 2 (HSD11B2) buffers fetal exposure by converting cortisol/corticosterone into inactive metabolites. Maternal stress during pregnancy down-regulates this enzyme and can induce epigenetic changes in placental and fetal tissues accounting for heightened adult HPA reactivity. Past studies have shown a placenta-specific increase in DNA methyltransferase (DNMT3a) mRNA in stressed mothers, an effect with implications for genome-wide epigenetic changes that may account for diverse phenotypic outcomes following maternal stress. Here we exposed groups of pregnant rats to one of five gravity loads (1, 1.5, 1.75 and 2G) and analyzed placental samples during late gestation. We predicted a systematic dose-response relationship between gravity load and the expression of the HSD11B2 and DNMT3 genes, thereby linking maternal exposure to altered gravity during pregancy with maternal stress.

Kalotia, Simranjit K.↗

NASA NTRS1984

Asynchronous file transfer to IBM PC's

The Asynchronous File Transfer System is used for interactively selecting and tramsmitting text files from the Langley Research Center's Business Data Systems Division (BDSD) host processor to an IBM Personal Computer. The IBM asynchronous communications support package is used for handling the communications on the personal computer. An application program (NATURAL, COBOL, etc.) is used for selecting and formatting the records to be transmitted, and three subroutine modules residing on the BDSD host processor are used for interfacing the application program and the communications software. Each record transmitted to the Personal Computer must be in the standard ASCII format. This record format is directly accessible by BASIC and many of the personal computer software packages provide utility programs for converting them to the format required for the particular package in question.

Hoerger, J.↗

NASA NTRS1980

YF-12 cooperative airframe/propulsion control system program, volume 1

Several YF-12C airplane analog control systems were converted to a digital system. Included were the air data computer, autopilot, inlet control system, and autothrottle systems. This conversion was performed to allow assessment of digital technology applications to supersonic cruise aircraft. The digital system was composed of a digital computer and specialized interface unit. A large scale mathematical simulation of the airplane was used for integration testing and software checkout.

Anderson, D. L.↗

NASA NTRS1984

Opening of an interface flaw in a layered elastic half-plane under compressive loading

A static analysis is given of the problem of an elastic layer perfectly bonded, except for a frictionless interface crack, to a dissimilar elastic half-plane. The free surface of the layer is loaded by a finite pressure distribution directly over the crack. The problem is formulated using the two dimensional linear elasticity equations. Using Fourier transforms, the governing equations are converted to a pair of coupled singular integral equations. The integral equations are reduced to a set of simultaneous algebraic equations by expanding the unknown functions in a series of Jacobi polynomials and then evaluating the singular Cauchy-type integrals. The resulting equations are found to be ill-conditioned and, consequently, are solved in the least-squares sense. Results from the analysis show that, under a normal pressure distribution on the free surface of the layer and depending on the combination of geometric and material parameters, the ends of the crack can open. The resulting stresses at the crack-tips are singular, implying that crack growth is possible. The extent of the opening and the crack-top stress intensity factors depend on the width of the pressure distribution zone, the layer thickness, and the relative material properties of the layer and half-plane.

Kennedy, J. M.↗

NASA NTRS1975

University of Utah (Wallops) precision meteorological data digitizer

The data digitizing system takes pulsed signals from meteorological rocket sondes and radiosondes and converts the information (the time interval between pulses) into a digital form for magnetic recording and further processing by digital computer. The basic digitizer configuration contains a master sequencer that allows for data storage and release in an accumulator. Thus, the digitizer provides for convenient interfacing in real time monitoring.

Staffanson, F. L.↗

NASA NTRS1990

The kinetics of the Au-InP interaction

An analysis of the reaction of Au and Au-In alloys with InP has permitted the identification of the mechanisms occurring during the first two stages of the Au-InP interaction. The first stage of the interaction, during which the Au is converted to a saturated Au (In) solution, is controlled by the vacancy-generation rate at the free surface of the metallization. The activation energy for this process is the activation energy for Au self-diffusion. Evidence is presented for the existence of large localized variations in this value due to surface related effects. At the completion of stage I stage II becomes active and continues until the metallization is converted to Au3In. This process, proceeding via an interstitial interchange mechanism, is many orders of magnitude slower than stage I. The rate-limiting step, with an activation energy of 2.8 eV, is shown to be the diffusion of In from the InP-metal interface. The P atoms that are released when In enters the metallization during stage I leave the system without reacting, whereas in stage II they form a compound (Au2P3) at the InP-metal interface. The presence of the Au2P3 severely retards the stage II interaction rate.

Fatemi, Navid S.↗

NASA NTRS1991

A double-stage injection-locked oscillator for optically fed phased array antennas

In an optically fed phased array antenna system, the microwave carrier signal is transmitted via a modulated lightwave to each active T/R (transmit/receive) module, where it must be converted back to the microwave domain. Currently, efficient optical-to-microwave conversion is extremely difficult, as the detected microwave signal is weak and noisy. A novel circuit, containing a high-gain/low-noise microwave injection-locked oscillator, has been developed to improve the interface between the optical and microwave components. The circuit utilizes two FETs and a dielectric resonator, which serves as a frequency-dependent feedback element. The circuit, designed to operate at about 8 GHz, provides significant amplitude and phase noise suppression. In addition, the circuit realization is compatible with MMIC technology.

Berceli, Tibor↗

NASA NTRS2008

Mars Reconnaissance Orbiter Uplink Analysis Tool

This software analyzes Mars Reconnaissance Orbiter (MRO) orbital geometry with respect to Mars Exploration Rover (MER) contact windows, and is the first tool of its kind designed specifically to support MRO-MER interface coordination. Prior to this automated tool, this analysis was done manually with Excel and the UNIX command line. In total, the process would take approximately 30 minutes for each analysis. The current automated analysis takes less than 30 seconds. This tool resides on the flight machine and uses a PHP interface that does the entire analysis of the input files and takes into account one-way light time from another input file. Input flies are copied over to the proper directories and are dynamically read into the tool s interface. The user can then choose the corresponding input files based on the time frame desired for analysis. After submission of the Web form, the tool merges the two files into a single, time-ordered listing of events for both spacecraft. The times are converted to the same reference time (Earth Transmit Time) by reading in a light time file and performing the calculations necessary to shift the time formats. The program also has the ability to vary the size of the keep-out window on the main page of the analysis tool by inputting a custom time for padding each MRO event time. The parameters on the form are read in and passed to the second page for analysis. Everything is fully coded in PHP and can be accessed by anyone with access to the machine via Web page. This uplink tool will continue to be used for the duration of the MER mission's needs for X-band uplinks. Future missions also can use the tools to check overflight times as well as potential site observation times. Adaptation of the input files to the proper format, and the window keep-out times, would allow for other analyses. Any operations task that uses the idea of keep-out windows will have a use for this program.

Khanampompan, Teerapat↗

NASA NTRS2017

Radioisotope Heater Unit-Based Stirling Power Convertor Development at NASA Glenn Research Center

Stirling Radioisotope Power Systems (RPS) are being developed as an option to provide power on future space science missions where robotic spacecraft will orbit, flyby, land or rove. A variety of mission concepts have been studied by NASA and the U. S. Department of Energy that would utilize RPS for landers, probes, and rovers and only require milliwatts to tens of watts of power. These missions would contain science measuring instruments that could be distributed across planetary surfaces or near objects of interest in space solar flux insufficient for using solar cells. A low power Stirling convertor is being developed to provide an RPS option for future low power applications. Initial concepts convert heat available from several Radioisotope Heater Units to electrical power for spacecraft instruments and communication. Initial development activity includes defining and evaluating a variety of Stirling configurations and selecting one for detailed design, research of advanced manufacturing methods that could simplify fabrication, evaluating thermal interfaces, characterizing components and subassemblies to validate design codes, and preparing for an upcoming demonstration of proof of concept in a laboratory environment.

Wilson, Scott D.↗

NASA NTRS2018

Radioisotope Heater Unit-Based Stirling Power Convertor Development at NASA Glenn Research Center

Stirling Radioisotope Power Systems (RPS) are being developed as an option to provide power on future space science missions where robotic spacecraft will orbit, flyby, land or rove. A variety of mission concepts have been studied by NASA and the U. S. Department of Energy that would utilize RPS for landers, probes, and rovers and only require milliwatts to tens of watts of power. These missions would contain science measuring instruments that could be distributed across planetary surfaces or near objects of interest in space solar flux insufficient for using solar cells. A low power Stirling convertor is being developed to provide an RPS option for future low power applications. Initial concepts convert heat available from several Radioisotope Heater Units to electrical power for spacecraft instruments and communication. Initial development activity includes defining and evaluating a variety of Stirling configurations and selecting one for detailed design, research of advanced manufacturing methods that could simplify fabrication, evaluating thermal interfaces, characterizing components and subassemblies to validate design codes, and preparing for an upcoming demonstration of proof of concept in a laboratory environment.

Wilson, Scott D.↗

NASA NTRS1999

GCR Transport in the Brain: Assessment of Self-Shielding, Columnar Damage, and Nuclear Reactions on Cell Inactivation Rates

Radiation shield design is driven by the need to limit radiation risks while optimizing risk reduction with launch mass/expense penalties. Both limitation and optimization objectives require the development of accurate and complete means for evaluating the effectiveness of various shield materials and body-self shielding. For galactic cosmic rays (GCR), biophysical response models indicate that track structure effects lead to substantially different assessments of shielding effectiveness relative to assessments based on LET-dependent quality factors. Methods for assessing risk to the central nervous system (CNS) from heavy ions are poorly understood at this time. High-energy and charge (HZE) ion can produce tissue events resulting in damage to clusters of cells in a columnar fashion, especially for stopping heavy ions. Grahn (1973) and Todd (1986) have discussed a microlesion concept or model of stochastic tissue events in analyzing damage from HZE's. Some tissues, including the CNS, maybe sensitive to microlesion's or stochastic tissue events in a manner not illuminated by either conventional dosimetry or fluence-based risk factors. HZE ions may also produce important lateral damage to adjacent cells. Fluences of high-energy proton and alpha particles in the GCR are many times higher than HZE ions. Behind spacecraft and body self-shielding the ratio of protons, alpha particles, and neutrons to HZE ions increases several-fold from free-space values. Models of GCR damage behind shielding have placed large concern on the role of target fragments produced from tissue atoms. The self-shielding of the brain reduces the number of heavy ions reaching the interior regions by a large amount and the remaining light particle environment (protons, neutrons, deuterons. and alpha particles) may be the greatest concern. Tracks of high-energy proton produce nuclear reactions in tissue, which can deposit doses of more than 1 Gv within 5 - 10 cell layers. Information on rates of cell killing from GCR, including patterns of cell killing from single particle tracks. can provide useful information on expected differences between proton and HZE tracks and clinical experiences with photon irradiation. To model effects on cells in the brain, it is important that transport models accurately describe changes in the GCR due to interactions in the cranium and proximate tissues. We describe calculations of the attenuated GCR particle fluxes at three dose-points in the brain and associated patterns of cell killing using biophysical models. The effects of the brain self-shielding and bone-tissue interface of the skull in modulating the GCR environment are considered. For each brain dose-point, the mass distribution in the surrounding 4(pi) solid angle is characterized using the CAM model to trace 512 rays. The CAM model describes the self-shielding by converting the tissue distribution to mass-equivalent aluminum, and nominal values of spacecraft shielding is considered. Particle transport is performed with the proton, neutron, and heavy-ion transport code HZETRN with the nuclear fragmentation model QMSFRG. The distribution of cells killed along the path of individual GCR ions is modeled using in vitro cell inactivation data for cells with varying sensitivity. Monte Carlo simulations of arrays of inactivated cells are considered for protons and heavy ions and used to describe the absolute number of cell killing events of various magnitude in the brain from the GCR. Included are simulations of positions of inactivated cells from stopping heavy ions and nuclear stars produced by high-energy ions most importantly, protons and neutrons.

Shavers, M. R.↗

NASA NTRSDate not supplied

Twin nucleation and growth mechanism in Ni-based superalloys

While micro-twinning is the dominant creep deformation mechanism in Ni-based superalloys at temperatures above 700 C, many aspects of twin nucleation and growth remain unexplored. Kolbe mechanism for micro-twinning, based on thermally activated reordering, is probably the only concept currently widely accepted by the scientific community. We propose a qualitatively different mechanism for nucleation and growth of twins. The mechanism can be briefly described as follows. Penetration of a gamma prime precipitate by two 1/2(110) edge dislocations travelling on adjacent {111} glide planes triggers nucleation (at the interface of the precipitate and the matrix) and emission of Shockley partial of screw character on the glide plane of the edge dislocation, which entered the precipitate first (generating trailing high-energy anti-phase boundary (APB)). Propagation of this Shockley partial into the precipitate converts the APB into super intrinsic stacking fault (SISF). The recurring arrival of additional edge dislocations on the glide planes adjacent to the configuration described above leads to formation of super extrinsic stacking fault SESF, subsequent micro-twin formation, and growth of the twinned region. We demonstrate the proposed mechanism via molecular dynamics simulations.

Ni-superalloys↗

NASA NTRSDate not supplied

Twin nucleation and growth mechanism in Ni-based superalloys

While micro-twinning is the dominant creep deformation mechanism in Ni-based superalloys at temperatures above 700 C, many aspects of twin nucleation and growth remain unexplored. Kolbe mechanism for micro-twinning, based on thermally activated reordering, is probably the only concept currently widely accepted by the scientific community. We propose a qualitatively different mechanism for nucleation and growth of twins. The mechanism can be briefly described as follows. Penetration of a   precipitate by two 1/2(110) edge dislocations travelling on adjacent {111} glide planes triggers nucleation (at the interface of the precipitate and the matrix) and emission of Shockley partial of screw character on the glide plane of the edge dislocation, which entered the precipitate first (generating trailing high-energy anti-phase boundary (APB)). Propagation of this Shockley partial into the precipitate converts the APB into super intrinsic stacking fault (SISF). The recurring arrival of additional edge dislocations on the glide planes adjacent to the configuration described above leads to formation of super extrinsic stacking fault SESF, subsequent micro-twin formation, and growth of the twinned region. We demonstrate the proposed mechanism via molecular dynamics simulations.

Ni-based superalloys↗

NASA NTRS1986

A method for coupling a parameterization of the planetary boundary layer with a hydrologic model

Deardorff's parameterization of the planetary boundary layer is adapted to drive a hydrologic model. The method converts the atmospheric conditions measured at the anemometer height at one site to the mean values in the planetary boundary layer; it then uses the planetary boundary layer parameterization and the hydrologic variables to calculate the fluxes of momentum, heat and moisture at the atmosphere-land interface for a different site. A simplified hydrologic model is used for a simulation study of soil moisture and ground temperature on three different land surface covers. The results indicate that this method can be used to drive a spatially distributed hydrologic model by using observed data available at a meteorological station located on or nearby the site.

Lin, J. D.↗