SEARCH · Engineering Papers

Results for “hypersonic flow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

All sources NASA NTRS DOE OSTI

NASA NTRS1973

Off-center-line shock interference heating patterns on basic shapes in hypersonic flows

The results of an experimental study of off-center-line shock-interference heating on basic shapes at hypersonic speeds are presented. The study covered three types of shock-interference patterns over a range of nominal Mach numbers (6 to 20), specific heat ratios (1.40 and 1.67), free-stream Reynolds numbers(8 million to 26 million per meter), and impinging shock strengths. Heat-transfer rates higher than stagnation levels were measured over much of the off-center-line model surface. Peak heating up to 17 times the stagnation heating was measured.

Keyes, J. W.↗

NASA NTRS2001

Hypersonic Flows About a 25 degree Sharp Cone

This paper presents the results of a numerical study that examines the surface heating discrepancies observed between computed and measured values along a sharp cone. With Mach numbers of an order of 10 and the freestream length Reynolds number of an order of 10 000, the present computations have been made with the direct simulation Monte Carlo (DSMC) method by using the G2 code of Bird. The flow conditions are those specified for two experiments conducted in the Veridian 48-inch Hypersonic Shock Tunnel. Axisymmetric simulations are made since the test model was assumed to be at zero incidence. Details of the current calculations are presented, along with comparisons between the experimental data, for surface heating and pressure distributions. Results of the comparisons show major differences in measured and calculated results for heating distributions, with differences in excess of 25 percent for the two cases examined.

Moss, James N.↗

NASA NTRS2004

DSMC Simulations of Hypersonic Flows With Shock Interactions and Validation With Experiments

The capabilities of a relatively new direct simulation Monte Carlo (DSMC) code are examined for the problem of hypersonic laminar shock/shock and shock/boundary layer interactions, where boundary layer separation is an important feature of the flow. Flow about two model configurations is considered, where both configurations (a biconic and a hollow cylinder-flare) have recent published experimental measurements. The computations are made by using the DS2V code of Bird, a general two-dimensional/axisymmetric time accurate code that incorporates many of the advances in DSMC over the past decade. The current focus is on flows produced in ground-based facilities at Mach 12 and 16 test conditions with nitrogen as the test gas and the test models at zero incidence. Results presented highlight the sensitivity of the calculations to grid resolution, sensitivity to physical modeling parameters, and comparison with experimental measurements. Information is provided concerning the flow structure and surface results for the extent of separation, heating, pressure, and skin friction.

Moss, James N.↗

NASA NTRS2004

DSMC Simulations of Hypersonic Flows With Shock Interactions and Validation With Experiments

The capabilities of a relatively new direct simulation Monte Carlo (DSMC) code are examined for the problem of hypersonic laminar shock/shock and shock/boundary layer interactions, where boundary layer separation is an important feature of the flow. Flow about two model configurations is considered, where both configurations (a biconic and a hollow cylinder-flare) have recent published experimental measurements. The computations are made by using the DS2V code of Bird, a general two-dimensional/axisymmetric time accurate code that incorporates many of the advances in DSMC over the past decade. The current focus is on flows produced in ground-based facilities at Mach 12 and 16 test conditions with nitrogen as the test gas and the test models at zero incidence. Results presented highlight the sensitivity of the calculations to grid resolutions, sensitivity to physical modeling parameters, and comparison with experimental measurements. Information is provided concerning the flow structure and surface results for the extent of separation, heating, pressure, and skin friction.

Moss, James N.↗

NASA NTRS1995

Hypersonic flows as related to the National Aerospace Plane

The object of Cooperative Agreement NCC2-452 was to identify, develop, and document reliable turbulence models for incorporation into CFD codes, which would then subsequently be incorporated into numerical design procedures for the NASP and any other hypersonic vehicles. In a two-pronged effort, consisting of an experimental and a theoretical approach, several key features of flows over complex vehicles were identified, and test bodies were designed which were composed of simple geometric shapes over which these flow features were measured. The experiments were conducted in the 3.5' Hypersonic Wind Tunnel at NASA Ames Research Center, at nominal Mach numbers from 7 to 8.3 and Re/m from 4.9 x 10(exp 6) to 5.8 x 10(exp 6). Boundary layers approaching the interaction region were 2.5 to 3.7 cm thick. Surface and flow field measurements were conducted, and the initial boundary conditions were experimentally documented.

Kussoy, Marvin↗

NASA NTRSDate not supplied

Nonlinear Nonmodal Analysis of Hypersonic Flow over Blunt Cones

The linear amplification of modal disturbances that lead to boundary-layer transition in two-dimensional/axisymmetric hypersonic configurations is strongly reduced by the presence of a blunt nosetip, and the mechanisms underlying the observed onset of transition over the cone frustum are currently unknown. Linear nonmodal analysis has shown that both planar and oblique traveling disturbances that peak within the entropy layer experience appreciable energy amplification for moderate to large nosetip bluntness. The present study extends the previous linear analysis by including the nonlinear effects. Specifically, the perturbation form of the 2D, harmonic Navier-Stokes equations (HNSE) are solved with a fully implicit formulation and the Newton-Raphson method. The increased number of degrees of freedom for the nonlinear system presents difficulties for solution strategies based on direct solution of the linearized system. Such difficulties are overcome by using the GMRES iterative method with a preconditioner corresponding to a simplified Jacobian without the cross derivative terms. The HNSE solver is verified by comparing with nonlinear parabolized stability equation (NPSE) results for the nonlinear evolution of planar waves in an incompressible Blasius boundary layer and in a Mach 6 flow over a blunt cone. Finally, nonlinear nonmodal results are presented for planar traveling disturbances over the blunt cone. The nonmodal analysis demonstrates that entropy-layer disturbances generated close to the nose tip can seed the amplification of higher frequency Mack’s second-mode instabilities further downstream.

boundary layer transition↗

NASA NTRSDate not supplied

Nonlinear Nonmodal Analysis of Hypersonic Flow over Blunt Cones

boundary layer transition↗

NASA NTRS1979

Approximate convective heating equations for hypersonic flows

Laminar and turbulent heating-rate equations appropriate for engineering predictions of the convective heating rates about blunt reentry spacecraft at hypersonic conditions are developed. The approximate methods are applicable to both nonreacting and reacting gas mixtures for either constant or variable-entropy edge conditions. A procedure which accounts for variable-entropy effects and is not based on mass balancing is presented. Results of the approximate heating methods are in good agreement with existing experimental results as well as boundary-layer and viscous-shock-layer solutions.

Zoby, E. V.↗

NASA NTRS1993

Pressure and force measurements on models set in hypersonic flows: A review

A review of measurement techniques used to obtain aerodynamic forces and moments and surface/flow field pressures for models tested in impulse hypersonic-hypervelocity facilities and in conventional-type hypersonic wind tunnels is presented. Although force and moment measurement techniques presently used in hypersonic wind tunnels are relatively unchanged from the 1960's and 1970's, significant advances have recently been made for impulse facilities. For both hypersonic wind tunnels and impulse facilities, the state-of-the-art has advanced via refinements, improved test techniques, and advances in semiconductor technology, data acquisition systems, and computers. The introduction of electronically scanned pressure systems over a decade ago 'revolutionized' pressure measurements in hypersonic wind tunnels and a second 'revolution' is impending with the development and application of optical, two-dimensional, global pressure measurement techniques. The development and continued refinement of miniature piezoresistive transducers has provided the capability to perform detailed surface pressure measurements on relatively small, complex models in impulse facilities; these transducers also provided the capability for intrusive flow field pressure measurements with miniature survey rakes.

Miller, Charles G.↗

NASA NTRS1999

Hypersonic Flow Control Using Upstream Focused Energy Deposition

A numerical study of centerline and off-centerline power deposition at a point upstream of a two-dimensional blunt body at Mach 6.5 at 30 km altitude are presented. The full Navier-Stokes equations are used. Wave drag, lift, and pitching moment are presented as a function of amount of power absorbed in the flow and absorption point location. It is shown that wave drag is considerably reduced. Modifications to the pressure distribution in the flow field due to the injected energy create lift and a pitching moment when the injection is off-centerline. This flow control concept may lead to effective ways to improve the performance and to stabilize and control hypersonic vehicles.

Riggins David W.↗

NASA NTRS1976

Effect of geometry modifications on effectiveness of slot injection in hypersonic flow

The study presents wind-tunnel measurements of surface static pressures, equilibrium temperatures, and skin friction downstream of tangential slot injection into a thick turbulent hypersonic boundary layer from two modified slot configurations. The data are compared with results obtained for baseline configurations reported by Cary and Hefner (1970, 1972) to determine whether simple modifications to the slot configuration can produce improved cooling effectiveness and skin friction reduction. The baseline slot configurations are simply modified by thickening the slot lip and by elevating the location of the slot exit above the flat plate. Although the results indicate that simple modifications of the baseline slot configurations can enhance the skin friction reductions obtained with tangential slot injection, slot base drag estimates show that neither of the modifications will lessen the impact of the systems penalties for collecting, ducting, and injecting the slot air.

Hefner, J. N.↗

NASA NTRS1995

Development of a two-equation turbulence model for hypersonic flows: Evaluation of a low Reynolds number correction to the Kappa - epsilon two equation compressible turbulence model - Volume 1

The objective of the current research is the development of an improved k-epsilon two-equation compressible turbulence model for turbulent boundary layer flows experiencing strong viscous-inviscid interactions. The development of an improved model is important in the design of hypersonic vehicles such as the National Aerospace Plane (NASP) and the High Speed Civil Transport (HSCT). Improvements have been made to the low Reynolds number functions in the eddy viscosity and dissipation of solenoidal dissipation of the k-epsilon turbulence mode. These corrections offer easily applicable modifications that may be utilized for more complex geometries. The low Reynolds number corrections are functions of the turbulent Reynolds number and are therefore independent of the coordinate system. The proposed model offers advantages over some current models which are based upon the physical distance from the wall, that modify the constants of the standard model, or that make more corrections than are necessary to the governing equations. The code has been developed to solve the Favre averaged, boundary layer equations for mass, momentum, energy, turbulence kinetic energy, and dissipation of solenoidal dissipation using Keller's box scheme and the Newton spatial marching method. The code has been validated by removing the turbulent terms and comparing the solution with the Blasius solution, and by comparing the turbulent solution with an existing k-epsilon model code using wall function boundary conditions. Excellent agreement is seen between the computed solution and the Blasius solution, and between the two codes. The model has been tested for both subsonic and supersonic flat-plate turbulent boundary layer flow by comparing the computed skin friction with the Van Driest II theory and the experimental data of Weighardt; by comparing the transformed velocity profile with the data of Weighardt, and the Law of the Wall and the Law of the Wake; and by comparing the computed results of an adverse pressure gradient with the experimental data of Fernando and Smits. Good agreement is obtained with the experimental correlations for all flow conditions.

Knight, Doyle D.↗

NASA NTRS1978

Analysis of heat transfer in a simulated wing-elevon cove in hypersonic flow

A simplified analytical model of leakage into a wing-elevon cove under high speed external flow conditions is presented. The model accounts for convection from the high temperature gas stream leaking into the cove, radiation exchanges between walls and with the environment, and axial conduction within the channel walls. Comparisons are made of predicted and measured wall temperatures of an experimental wing-elevon-cove model that was tested in a hypersonic wind tunnel. Analytically determined Nusselt numbers for laminar flow entrance conditions are compared with those calculated from experimentally measured gas temperatures, wall temperatures and wall heating rates. Although reasonable agreement appears to be indicated, testing times much larger than those of the present test program (5 seconds) would be desirable in evaluating the reliability and accuracy of the simplified model.

Keshock, E. G.↗

NASA NTRS1992

Large-amplitude finite element flutter analysis of composite panels in hypersonic flow

Consideration is given to a finite-element approach for determining the nonlinear flutter characteristics of 3D thin laminated composite panels using the full third-order-piston transverse-loading aerodynamic theory. The unsteady hypersonic aerodynamic theory and the von Karman large-deflection-plate theory are used to formulate the aeroelasticity problem. Nonlinear flutter analyses are performed to assess the influence of the higher-order aerodynamic theory on the structure's limit-cycle amplitude and the dynamic pressure of the flow velocity. A solution procedure is presented to solve the nonlinear panel flutter and large-amplitude free-vibration finite-element equations. Nonlinear flutter analyses are performed for different boundary support-conditions and for various system parameters. Linear finite-element flutter for isotropic and composite panels and large-amplitude isotropic panel flutter results are compared with existing classical solutions. The large-amplitude panel flutter results using the full third-order piston aerodynamic theory are presented to assess the influence of the nonlinear aerodynamic theory.

Gray, Carl E., Jr.↗

NASA NTRS2002

Prediction of Drag Reduction in Supersonic and Hypersonic Flows with Counterflow Jets

Computational fluid dynamics solutions of the flowfield of a truncated cone-cylinder with and without counterflow jets have been obtained for the short penetration mode (SPM) and long penetration mode (LPM) of the freestream-counterflow jet interaction flowfield. For the case without the counterflow jet, the comparison of the normalized surface pressures showed very good agreement with experimental data. For the case with the SPM jet, the predicted surface pressures did not compare as well with the experimental data upstream of the expansion corner, while aft of the expansion corner, the comparison of the solution and the data is seen to give much better agreement. The difference in the prediction and the data could be due to the transient character of the jet penetration modes, possible effects of the plasma physics that are not accounted for here, or even the less likely effect of flow turbulence, etc. For the LPM jet computations, one-dimensional isentropic relations were used to derived the jet exit conditions in order to obtain the LPM solutions. The solution for the jet exit Mach number of 3 shows a jet penetration several times longer than that of the SPM, and therefore much weaker bow shock, with an attendant reduction in wave drag. The LPM jet is, in essence, seen to be a "pencil" of fluid, with much higher dynamic pressure, embedded in the oncoming supersonic or hypersonic freestream. The methodology for determining the conditions for the LPM jet could enable a practical approach for the design and application of counterflow LPM jets for the reduction of wave drag and heat flux, thus significantly enhancing the aerodynamic characteristics and aerothermal performance of supersonic and hypersonic vehicles. The solutions show that the qualitative flow structure is very well captured. The obtained results, therefore, suggest that counterflowing jets are viable candidate technology concepts that can be employed to give significant reductions in wave drag, heat flux, and other attendant aerodynamic benefits.

Daso, Endwell O.↗

NASA NTRS1990

Flat plate at incidence as a waverider in rarefied hypersonic flow

The physical validity of continuum models and their ability to predict the critical aerothermodynamic properties of a waverider at high altitudes are examined using a flat plate at angle of attack as a generic hypersonic lifting vehicle. For a shock layer far from local translational equilibrium, a theoretical study based on Grad's thirteen-moment equations shows that the Navier-Stokes based solutions can correctly predict the drag, lift, and surface heat transfer rate, with the prediction error comparable to that of the standard shock-layer theory. The conclusion is supported by a comparison with direct simulation Monte Carlo calculations.

Cheng, H. K.↗

NASA NTRS1975

A comparison of measured and predicted sphere shock shapes in hypersonic flows with density ratios from 4 to 19

Measured shock shapes are presented for sphere and hemisphere models in helium, air, CF4, C2F6, and CO2 test gases, corresponding to normal-shock density ratios (primary factor governing shock detachment distance of blunt bodies at hypersonic speeds) from 4 to 19. These shock shapes were obtained in three facilities capable of generating the high density ratios experienced during planetary entry at hypersonic conditions; namely, the 6-inch expansion tube, with hypersonic CF4 tunnel, and pilot CF4 Mach 6 tunnel (with CF4 replaced by C2F6). Measured results are compared with several inviscid perfect-gas shock shape predictions, in which an effective ratio of specific heats is used as input, and with real-gas predictions which include effects of a laminar viscous layer and thermochemical nonequilibrium.

Miller, C. G., III↗

NASA NTRS1989

Rotational and vibrational nonequilibrium effects in rarefied, hypersonic flow

Results are reported for an investigation into the methods by which energy transfer is calculated in the Direct Simulation Monte Carlo method. Description is made of a recently developed energy exchange model that deals with the translational and rotational modes. A new model for simulating the transfer of energy between the translational and vibrational modes is also explained. This model allows the vibrational relaxation time to follow the temperature dependence predicted by the Landau-Teller theory at moderate temperatures. For temperatures in excess of about 8000K the vibrational model is extended to include an empirical result for the relaxation time. The effect of introducing these temperature dependent collision numbers into the DSMC technique is assessed by making calculations representative of the stagnation streamline of a hypersonic space vehicle. Both thermal and chemical nonequilibrium effects are included while the flow conditions have been chosen such that ionization and radiation may be neglected. The introduction of these new models is found to significantly affect the degree of thermal nonequilibrium observed in the flowfield. Larger, and more widely ranging, differences in the results obtained with the different energy exchange probabilities are found when a significant amount of internal energy is included in the calculation of chemical nonequilibrium.

Boyd, Iain D.↗