SEARCH · Engineering Papers

Results for “high rate”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

All sources NASA NTRS DOE OSTI

NASA NTRS1978

Testing of fiber composites at high strain rates

An experimental investigation was conducted to determine strain rate effects in fiber composites. Unidirectional composite specimens of boron/epoxy, graphite/epoxy, S-glass/epoxy and Kevlar/epoxy were tested at tensile strain rates of up to 27 m/m/sec. Longitudinal, transverse and in-plane shear properties, including modulus, Poisson's ratio, strength and ultimate strain, were determined by testing 0-, 90and 10-degree unidirectional coupons. Strains were measured by means of strain gages bonded on the coupons and loads were measured by means of a strain gage load cell. All specimens were loaded in an electrohydraulic loading system. The 0-degree properties which are governed by the fibers do not vary much with strain rate except for the Kevlar/epoxy material which shows an increase in both modulus and strength. The strain rate effects on 90-degree properties were small with a general trend toward higher strength with increasing strain rate. The most noticeable effect was on in-plane shear properties with shear strength values at high strain rates approximately fifteen percent higher than static values.

Daniel, I. M.↗

NASA NTRS2019

EDOS Initiatives to Decrease Latency of NRT Data for LANCE

NASA's EOS Data and Operations System (EDOS) is the primary supplier of NRT (near real-time) data to the NASA NRT user community known as the Land, Atmosphere NRT Capability for EOS (LANCE). EDOS provides NRT data for various instruments on the EOS missions Terra, Aqua, Aura, as well as for the NOAA missions Suomi NPP and NOAA-20. This poster describes an overview of the EDOS multi-mission system with emphasis on the NRT products distributed for LANCE elements: AIRS, MISR, MLS, MODIS, MOPITT, OMPS, OMI and VIIRS. Remote EDOS high-rate data capture systems are deployed at NASA ground stations which provide data-driven capture of high-rate science for EOS missions. The remote EDOS components transfer the science data via high-rate WANs to the centralized EDOS Level-zero processing systems located at Goddard Space Flight Center. EDOS produces session-based data sets especially for LANCE NRT use from a single ground station contact; this data is sent to dual LANCE destinations as part of the standard redundancy requirement for LANCE elements. EDOS has implemented various latency improvements with the ultimate goal to have EDOS processing of NRT data keep up with the spacecraft data downlink. EDOS enhancements have included implementation of priority-based QoS, expanded network architecture to include open networks, and use of a delay-tolerant protocol. EDOS has streamlined its systems and infrastructure to minimize latency for NRT data delivery for LANCE. EDOS begins to transfer the NRT data to the LANCE elements within minutes of the end of the contact session with an average packet latency from instrument observation to Level 0 product delivery to each LANCE element of just over one hour.

Michael, Karen↗

NASA NTRS1992

Time dependent heat transfer rates in high Reynolds number hypersonic flowfields

Time dependent heat transfer rates have been calculated from time dependent temperature measurements in the vicinity of shock-wave boundary-layer interactions due to conical compression ramps on an axisymmetric body. The basic model is a cylindrical body with a 10 degree conical nose. Four conical ramps, 20, 25, 30, and 35 degrees serve as shock wave generators. Flowfield surveys have been made in the vicinity of the conical ramp vertex, the separation point, and the reattachment point. A significant effort was made to characterize the natural frequencies and relative powers of the resulting fluctuations in heat transfer rates. This research effort, sponsored jointly by NASA and the Air Force, was conducted in the Air Force Flight Dynamics Directorate High Reynolds Facility. The nominal freestream Mach number was 6, and the freestream Reynolds numbers ranged from 2.2 million/ft to 30.0 million/ft. Experimental results quantify temperature response and the resulting heat transfer rates as a function of ramp angle and Reynolds number. The temperature response within the flowfield appears to be steady-state for all compression ramp angles and all Reynolds numbers, and hence, the heat transfer rates appear to be steady-state.

Flanagan, Michael J.↗

NASA NTRS2003

Study of High Strain Rate Response of Composites

The objective of the research was to continue the experimental study of the effect of strain rate on mechanical response (deformation and failure) of epoxy resins and carbon fibers/epoxy matrix composites, and to initiate a study of the effects of temperature by developing an elevated temperature test. The experimental data provide the information needed for NASA scientists for the development of a nonlinear, rate dependent deformation and strength models for composites that can subsequently be used in design. This year effort was directed into testing the epoxy resin. Three types of epoxy resins were tested in tension and shear at various strain rates that ranges from 5 x 10(exp -5), to 1000 per second. Pilot shear experiments were done at high strain rate and an elevated temperature of 80 C. The results show that all, the strain rate, the mode of loading, and temperature significantly affect the response of epoxy.

Gilat, Amos↗

NASA NTRS2009

Microstructural Evolution of Ti-6Al-4V during High Strain Rate Conditions of Metal Cutting

The microstructural evolution following metal cutting was investigated within the metal chips of Ti-6Al-4V. Metal cutting was used to impose a high strain rate on the order of approx.10(exp 5)/s within the primary shear zone as the metal was removed from the workpiece. The initial microstructure of the parent material (PM) was composed of a bi-modal microstructure with coarse prior grains and equiaxed primary located at the boundaries. After metal cutting, the microstructure of the metal chips showed coarsening of the equiaxed primary grains and lamellar. These metallographic findings suggest that the metal chips experienced high temperatures which remained below the transus temperature.

Dong, Lei↗

NASA NTRS2018

Use of Open Networks and Delay-Tolerant Protocol to Decrease WAN Latency of EOS near Real-Time Data

Since 1999, NASA's Earth Observing System Data Operations System (EDOS) project at Goddard Space Flight Center (GSFC) has provided high-rate data capture, level zero processing, and product distribution services for a majority of NASA's EOS (Earth Observing System) high-rate missions, including Terra, Aqua, Aura, ICESat, EO-1, SMAP, and OCO-2. EDOS high-rate science and engineering (150-300 Mbps) data-driven capture systems are deployed at 7 worldwide ground stations which are connected via both private (closed) and public (open) wide area networks (WANs) to the centralized EDOS Level Zero Processing Facility (LZPF) located at GSFC, where the data is processed and Level 0 products are distributed to users worldwide. All data transferred over the open networks to GSFC traverse an IPSec tunnel, providing the same level of security as a VPN connection. EDOS produces both time-based and near real-time products (session-based). Near real-time data products are produced from a single ground station contact; time-based products are produced from multiple ground station contacts. EDOS is the primary supplier of EOS Level 0 data to the NASA near real-time user community known as the Land, Atmosphere Near real-time Capability for EOS (LANCE). For the past few years, EDOS has streamlined its systems to reduce WAN latency for near real-time data delivery, including implementing Quality of Service (QoS), expanding closed network bandwidth, adding open network connections with more bandwidth, and implementing a delay-tolerant protocol to mitigate long round-trip times to remote ground stations.

Delay-Tolerant Protocol↗

NASA NTRS1991

A comparison of optical technologies for a high data rate Mars link

Several optical systems, based on Nd:YAG, GaAs, and CO2 laser sources and employing both direct and heterodyne detection, are analyzed in order to assess their feasibility in providing high data rate (10-1000 Mbps) Mars-to-earth communications. The rms pointing/tracking accuracy is shown to be a critical parameter in defining the Mars-earth optical link. Data obtained reveal that unless, extremely small rms pointing and tracking errors can be achieved (sigma less than .2 microrad), the most promising optical implementation appears to be the Nd:YAG laser using direct detection and high order PPM modulation.

Spence, Rodney L.↗

NASA NTRS1999

Investigation of Near Shannon Limit Coding Schemes

Turbo codes can deliver performance that is very close to the Shannon limit. This report investigates algorithms for convolutional turbo codes and block turbo codes. Both coding schemes can achieve performance near Shannon limit. The performance of the schemes is obtained using computer simulations. There are three sections in this report. First section is the introduction. The fundamental knowledge about coding, block coding and convolutional coding is discussed. In the second section, the basic concepts of convolutional turbo codes are introduced and the performance of turbo codes, especially high rate turbo codes, is provided from the simulation results. After introducing all the parameters that help turbo codes achieve such a good performance, it is concluded that output weight distribution should be the main consideration in designing turbo codes. Based on the output weight distribution, the performance bounds for turbo codes are given. Then, the relationships between the output weight distribution and the factors like generator polynomial, interleaver and puncturing pattern are examined. The criterion for the best selection of system components is provided. The puncturing pattern algorithm is discussed in detail. Different puncturing patterns are compared for each high rate. For most of the high rate codes, the puncturing pattern does not show any significant effect on the code performance if pseudo - random interleaver is used in the system. For some special rate codes with poor performance, an alternative puncturing algorithm is designed which restores their performance close to the Shannon limit. Finally, in section three, for iterative decoding of block codes, the method of building trellis for block codes, the structure of the iterative decoding system and the calculation of extrinsic values are discussed.

Kwatra, S. C.↗

NASA NTRS1993

Advanced communications technology satellite high burst rate link evaluation terminal communication protocol software user's guide, version 1.0

The Communication Protocol Software was developed at the NASA Lewis Research Center to support the Advanced Communications Technology Satellite High Burst Rate Link Evaluation Terminal (ACTS HBR-LET). The HBR-LET is an experimenters terminal to communicate with the ACTS for various experiments by government, university, and industry agencies. The Communication Protocol Software is one segment of the Control and Performance Monitor (C&PM) Software system of the HBR-LET. The Communication Protocol Software allows users to control and configure the Intermediate Frequency Switch Matrix (IFSM) on board the ACTS to yield a desired path through the spacecraft payload. Besides IFSM control, the C&PM Software System is also responsible for instrument control during HBR-LET experiments, uplink power control of the HBR-LET to demonstrate power augmentation during signal fade events, and data display. The Communication Protocol Software User's Guide, Version 1.0 (NASA CR-189162) outlines the commands and procedures to install and operate the Communication Protocol Software. Configuration files used to control the IFSM, operator commands, and error recovery procedures are discussed. The Communication Protocol Software Maintenance Manual, Version 1.0 (NASA CR-189163, to be published) is a programmer's guide to the Communication Protocol Software. This manual details the current implementation of the software from a technical perspective. Included is an overview of the Communication Protocol Software, computer algorithms, format representations, and computer hardware configuration. The Communication Protocol Software Test Plan (NASA CR-189164, to be published) provides a step-by-step procedure to verify the operation of the software. Included in the Test Plan is command transmission, telemetry reception, error detection, and error recovery procedures.

Reinhart, Richard C.↗

NASA NTRS1990

Aperture synthesis CO observations of the inner disk of NGC 1068

NGC 1068 is probably the nearest galaxy with both a high rate of star formation and a high luminosity active nucleus. About one-half of the total IR luminosity originates in a disk approximately 30 seconds in size, which has been taken as evidence for a high rate of massive star formation (Telesco et al. 1984). Previous CO line observations have shown the existence of a ring at the outer boundary of the inner disk (Myers and Scoville 1987). Although these observations have proved that this ring is extremely rich in molecular gas (as suggested by Scoville et al. 1983), the angular resolution (approx. 6 seconds) was not high enough to resolve its structure. New aperture synthesis observations of the CO (J=1 to 0) emission in the inner disk of NGC 1068 have been carried out with the Owens Valley Radio Observatory (OVRO) mm Interferometer. The new receivers installed for the 88/89 season have allowed researchers to obtain a high sensitivity map of the CO emission. The molecular cloud ring has been resolved and continuum as well as line emission from the nucleus of the galaxy have been detected.

Planesas, P.↗

NASA NTRS1973

Multichannel telemetry system

A two-channel telemetry system is described in which one channel is used for high-rate data and the other channel for low-rate data communication. In the transmitter a signal, which subsequently phase modulates a carrier, is produced which is a function of at least the high-rate data, the low-rate data and the frequency of the subcarrier of the low-rate channel. In the receiver which includes a phase-locked loop, the high-rate data is detected off the receiver inphase channel output and the low-rate off the quadrature channel output.

Butman, S.↗

NASA NTRS2003

LS-DYNA Implementation of Polymer Matrix Composite Model Under High Strain Rate Impact

A recently developed constitutive model is implemented into LS-DYNA as a user defined material model (UMAT) to characterize the nonlinear strain rate dependent behavior of polymers. By utilizing this model within a micromechanics technique based on a laminate analogy, an algorithm to analyze the strain rate dependent, nonlinear deformation of a fiber reinforced polymer matrix composite is then developed as a UMAT to simulate the response of these composites under high strain rate impact. The models are designed for shell elements in order to ensure computational efficiency. Experimental and numerical stress-strain curves are compared for two representative polymers and a representative polymer matrix composite, with the analytical model predicting the experimental response reasonably well.

Zheng, Xia-Hua↗

NASA NTRS1992

Advanced Communications Technology Satellite high burst rate link evaluation terminal experiment control and monitor software maintenance manual, version 1.0

The Experiment Control and Monitor (EC&M) software was developed at NASA Lewis Research Center to support the Advanced Communications Technology Satellite (ACTS) High Burst Rate Link Evaluation Terminal (HBR-LET). The HBR-LET is an experimenter's terminal to communicate with the ACTS for various investigations by government agencies, universities, and industry. The EC&M software is one segment of the Control and Performance Monitoring (C&PM) software system of the HBR-LET. The EC&M software allows users to initialize, control, and monitor the instrumentation within the HBR-LET using a predefined sequence of commands. Besides instrument control, the C&PM software system is also responsible for computer communication between the HBR-LET and the ACTS NASA Ground Station and for uplink power control of the HBR-LET to demonstrate power augmentation during rain fade events. The EC&M Software User's Guide, Version 1.0 (NASA-CR-189160) outlines the commands required to install and operate the EC&M software. Input and output file descriptions, operator commands, and error recovery procedures are discussed in the document. The EC&M Software Maintenance Manual, Version 1.0 (NASA-CR-189161) is a programmer's guide that describes current implementation of the EC&M software from a technical perspective. An overview of the EC&M software, computer algorithms, format representation, and computer hardware configuration are included in the manual.

Reinhart, Richard C.↗

NASA NTRS1993

Advanced communications technology satellite high burst rate link evaluation terminal power control and rain fade software test plan, version 1.0

The Power Control and Rain Fade Software was developed at the NASA Lewis Research Center to support the Advanced Communications Technology Satellite High Burst Rate Link Evaluation Terminal (ACTS HBR-LET). The HBR-LET is an experimenters terminal to communicate with the ACTS for various experiments by government, university, and industry agencies. The Power Control and Rain Fade Software is one segment of the Control and Performance Monitor (C&PM) Software system of the HBR-LET. The Power Control and Rain Fade Software automatically controls the LET uplink power to compensate for signal fades. Besides power augmentation, the C&PM Software system is also responsible for instrument control during HBR-LET experiments, control of the Intermediate Frequency Switch Matrix on board the ACTS to yield a desired path through the spacecraft payload, and data display. The Power Control and Rain Fade Software User's Guide, Version 1.0 outlines the commands and procedures to install and operate the Power Control and Rain Fade Software. The Power Control and Rain Fade Software Maintenance Manual, Version 1.0 is a programmer's guide to the Power Control and Rain Fade Software. This manual details the current implementation of the software from a technical perspective. Included is an overview of the Power Control and Rain Fade Software, computer algorithms, format representations, and computer hardware configuration. The Power Control and Rain Fade Test Plan provides a step-by-step procedure to verify the operation of the software using a predetermined signal fade event. The Test Plan also provides a means to demonstrate the capability of the software.

Reinhart, Richard C.↗

NASA NTRS1992

Advanced communications technology satellite high burst rate link evaluation terminal experiment control and monitor software user's guide, version 1.0

Reinhart, Richard C.↗

NASA NTRS1992

High data rate applications of ACTS technology

Consideration is given to the existing Broadband Integrated Services Digital Network (BISDN), a delivery method as defined by the International Consultative Committee for Telephone and Telegraph, satellites' role in providing these services, and the NASA high data rate ACTS experiments. It is concluded that satellites have the capability to extend BISDN services beyond the range of the terrestrial BISDN and will provide certain BISDN services more cost effectively in a direct competitive or hybrid satellite-fiber implementation.

Vondeak, Thomas↗

NASA NTRS2001

The 'Brick Wall' radio loss approximation and the performance of strong channel codes for deep space applications at high data rates

In order to evaluate performance of strong channel codes in presence of imperfect carrier phase tracking for residual carrier BPSK modulation in this paper an approximate 'brick wall' model is developed which is independent of the channel code type for high data rates. It is shown that this approximation is reasonably accurate (less than 0.7dB for low FERs for (1784,1/6) code and less than 0.35dB for low FERs for (5920,1/6) code). Based on the approximation's accuracy, it is concluded that the effects of imperfect carrier tracking are more or less independent of the channel code type for strong channel codes. Therefore, the advantage that one strong channel code has over another with perfect carrier tracking translates to nearly the same advantage under imperfect carrier tracking conditions. This will allow the link designers to incorporate projected channel code performance of strong channel codes into their design tables without worrying about their behavior in the face of imperfect carrier phase tracking.

turbo codes↗

NASA NTRS1991

Sulfate reduction in deep-sea sediments

Sulfate reduction rates calculated from about 200 DSDP pore water sulfate profiles have been contoured and plotted on a map covering most areas of the world ocean. Rates show a remarkable spatial consistency, with high rates observed near the continental margins, becoming progressively lower toward the central ocean basins. Relatively elevated rates are also found in the eastern equatorial Pacific, a site of upwelling and correspondingly high rates of primary organic production. Overall, the distribution of sulfate reduction in pelagic sediments looks very similar to the distribution of primary organic carbon production. When rates are directly compared, however, the correlation between sulfate reduction and primary production is only moderately strong. Perhaps the most important influence on sulfate reduction is sediment deposition rate and the control this has over the fraction of the sedimentary organic carbon flux that becomes available for sulfate reduction. The slower the rate of sediment deposition the more time for oxic respiration and the less organic carbon that escapes to the zone of sulfate reduction. To predict most accurately sulfate reduction rates, however, the variables of primary production, water depth, and sediment deposition rate must all be integrated.

NASA Program Exobiology↗