Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “high modulus”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Spray Manufacturing Thermal Insulation Composites

Cellulose-based thermal insulation materials present significant potential for modern green building applications due to their inherent carbon sequestration properties. However, traditional manufacturing of composites often results in the limited thermal insulation performance and embodied carbon footprint due to an increased density from material shrinkage and higher energy consumption during the water-based slurry drying process. Here, we report solvent spraying coupled with dry powder feedstock to manufacture highly porous silica/straw insulation composites. The manufactured composite exhibits negligible shrinkage with the density of 0.08 g/cm 3 , thermal conductivity of 27.8 mW/(m·K), flexural modulus of 3.1 MPa, and compressive modulus of 0.89 MPa. Additionally, the prepared composite demonstrates fire retardancy (burning rate of 0.5 mm/min) and recyclability (99%). Furthermore, this solvent-spraying strategy opens up opportunities of energy-efficient insulation materials for carbon-sequestration building sectors.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Large-Area Lithium Electrode Sub-Assemblies (LESAs) Protected by Self Forming Microstructured Polymer-Inorganic Single-Ion Conducting Composites (Final Report)

The aim of this project is to realize a low-cost, safe, reversible, high-areal capacity lithium metal electrode though the use of scalable, low-cost Lithium Electrode Sub-Assembly (LESA). At its core, the LESA applies novel polymer scaffolds to nanostructure inorganic ionic materials into high-conductivity composites that stabilize lithium anodes during high-rate, high-capacity cycling in lithium metal batteries. Fundamental investigations from this project identified a newly defined region of stability for composites with respect to the shear modulus and lithium molar volume ratio which have been broadly applied in the scientific literature for a multitude of different systems. The advancements achieved in this field have furthered the fundamental understanding of lithium metal electrode chemistry and degradation mechanisms and resulted in a lithium metal anode with improved cycle life.

25 ENERGY STORAGE↗
DOE OSTI2020

Elastic moduli of high-density, sintered monoliths of yttrium dihydride

Yttrium dihydride has been considered as potential nuclear reactor moderator for micro-reactors operating in the thermal energy spectrum due to their ability to retain hydrogen to high temperatures while having a relatively low impact on neutron economy. Despite these advantages, it is difficult to prepare yttrium dihydride in high-density, near net-shape monoliths for moderator applications due to volume expansion upon hydriding and the pyrophoric nature of the material. In this work, high-density monoliths of yttrium dihydride were prepared by direct hydriding and using powder metallurgical methods. Resonant ultrasound spectroscopy was used to measure the elastic moduli of the sintered monoliths, while nanoindentation was used to determine the Young’s modulus and hardness of the directly-hydrided yttrium and the sintered monoliths. Single crystal elastic constants and related properties of yttrium dihydride were also determined using density functional theory (DFT) for comparison. We report mechanical properties of materials produced by both methods were observed to be consistent with the values from literature for yttrium dihydride. Due to the novelty of producing yttrium dihydride by powder metallurgy, this result indicated that the monoliths produced by powder metallurgy were of high quality. To that end, powder metallurgy is believed to be a viable method for large-scale production of yttrium dihydride monoliths for nuclear reactor moderator applications.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Reprocessable polyhydroxyurethane networks reinforced with reactive polyhedral oligomeric silsesquioxanes (POSS) and exhibiting excellent elevated temperature creep resistance

The rapid development of covalent adaptable networks or vitrimers shows promise for addressing the long-standing recycling issues associated with conventional, permanently cross-linked thermosets. At the same time, it is important to demonstrate that properties of reprocessable polymer networks can be optimized to meet the ongoing demand for high-performance materials. We have fabricated reprocessable polyhydroxyurethane (PHU) network composites reinforced with reactive polyhedral oligomeric silsesquioxanes (POSS). With functionalized POSS serving as a fraction of the cross-linkers, the PHU–POSS network nanocomposites exhibit significantly enhanced storage modulus at the rubbery plateau region relative to the neat PHU network. With up to 10 wt% POSS loading, these network composites can undergo melt-state reprocessing at 140 °C with 100% property recovery associated with cross-link density. We also show that hydroxyurethane dynamic chemistry leads to excellent creep resistance at elevated temperature up to 90 °C and is unaffected by reactive incorporation of POSS. In conclusion, this study demonstrates the effectiveness of POSS as nanofillers for designing high-performance, organic-inorganic dynamic PHU networks with excellent reprocessability.

42 ENGINEERING↗
DOE OSTI2023

Behavioral simulations and experimental evaluations of stress induced spatial nonuniformity of dynamic bulk modulus in additive friction stir deposited AA 6061

Additive friction stir deposition (AFSD) is a rapidly developing solid-state additive manufacturing (AM) technology that enables the fabrication of customized products on a relatively large scale. The unique forge-liked process offers high quality products with refined equiaxed microstructure and exceptional mechanical performance. However, in AFSD, the spatially distributed mechanical properties within a deposited layer have not been established so far, due to the lack of a suitable large-scale mapping method. In the present work, an ultrasonic dynamic-elasticity mapping method was employed to map the distribution of physical properties in a AFSD 6061 Al. Strong spatial asymmetries in elastographies were mainly due to the residual stresses. The origin of the asymmetries was investigated through thermo-mechanical simulations of the AFSD process. It was observed that majority of the asymmetries were associated with the mechanical residual stresses instead of the symmetric thermal residual stresses during linear deposition of the AFSD process. However, the thermal residual stresses can be manipulated to become asymmetric with a 90° turn in the linear deposition path, due to the difference between the levels of cooling along the edges of the inner and outer corners. Hence, the mechanical and thermo-mechanical residual stresses can be additive or subtractive depending on the direction of the turns. Here, such numerically predicted behaviors were also experimentally observed on the AFSD fabricated samples by ultrasonic elastography. Furthermore, additional preliminary studies on multi-layer AFSD fabrications show the asymmetric mechanical stresses generated during the deposition process on different layers generate constructive or destructive interference which results to spatially variable dynamic bulk modulus depending on the deposition orientations of layers.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Bayesian calibration of irradiated graphite property models under high temperatures

Graphite under high temperatures and irradiation is central to advanced reactors. We develop a Bayesian calibration framework for graphite property models that explicitly represents model-data mismatch via a Gaussian-process discrepancy. The approach propagates uncertainty from parameters, experimental noise, and model form, with a hierarchical variance structure to capture group and cross-group noise. Using two predictive models across five grades (IG-110, NBG-18, PCEA, NBG-17, 2114) and four properties-irradiation-induced dimension change, creep, Young’s modulus change ratio, and coefficient of thermal expansion change ratio-we obtain average predictive-error reductions of 54%, 65%, 17%, and 17% when discrepancy is included. We illustrate engineering impact with a multiphysics model of a very-high-temperature reactor prismatic reflector brick, analyzing stresses under high fluence and temperature. Accounting for model discrepancy markedly improves predictive accuracy and provides a robust basis for reliable graphite component design in advanced reactors.

36 - MATERIALS SCIENCE↗
DOE OSTI2020

On the Use of Surfactant-Complexed Chitosan for Toughening 3D Printed Polymethacrylate Composites

This work reports a simple approach to prepare toughened 3D-printed polymethacrylate (PMA) composites using surfactant-modified chitosan (SMCS) particles at loadings between 2–10 wt%. Chitosan (CS) is modified with anionic surfactant, sodium dodecyl sulfate, via ionic complexation to facilitate compatibility and dispersion of CS to PMA matrix by non-covalent interactions between the components. The study successfully demonstrates high-accuracy 3D printing of composites with significant improvements in the overall mechanical properties. The composite with the best loading of 8 wt% SMCS shows a tensile modulus of 1.23 ± 0.05 GPa, a tensile strength at 49.8 ± 0.96 MPa, a yield stress at 33.3 ± 1.48 MPa, and a strain-at-ailure 10.3 ± 0.61%, which are 45%, 40%, 32%, and 68% higher than neat PMA, respectively. This provides a significant improvement in toughness at 4.92 ± 0.55 MJ m -3 for the composite, 184% higher than that of neat PMA. The marked increase in toughness is due to enhanced filler-matrix interactions which improve the ability of the 3D printed composite to absorb energy under tensile load. The results from this work provide new understandings into the strategies for design and preparation of stereolithography 3D printed materials reinforced with toughening fillers from renewable resources.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Acrylonitrile-butadiene-lignin thermoplastic rubber adhesive for enhanced metal-to-metal joining

With the growing requirement for lightweight structural materials in automotive, aerospace, and infrastructure applications, multi-material joints made with adhesive have attracted intense research interest. Commercial thermoset adhesives are one-time cures, and difficult to disassemble the bonded components for repair and recycling. Our prior work with a thermoplastic acrylonitrile-butadiene-lignin rubber (ABL) addresses this sustainability/recycling challenge, but the adhesive exhibits deficient joining strength compared to standard thermosets. Here, we modify the ABL matrix by loading particulate fillers to enhance its modulus and toughness. Further, the goal is to manufacture a cure-free thermoplastic adhesive system with a simple dispensing protocol and characteristic ductility combined with a high yield stress for improved shear strength of a bonded joint. Fumed silica (FS) and epoxidized glass spheres (EGS) were used as fillers in the ABL to promote the dispersion of lignin particles that tailored the functionalities and free energy components of the adhesive surface. With optimal loading of FS (5 wt%) and EGS (30 wt%) in the ABL adhesive matrix, the lap-shear strength of the bonded aluminum joint was elevated by 128%, compared to the neat ABL, reaching 21 MPa, which is 90% of the performance of a commercial epoxy-based adhesive.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Using post-processing heat treatments to elucidate precipitate strengthening of additively manufactured superalloy 718

The poor machinability and extensive work hardening of Ni-based superalloys makes additive manufacturing an attractive option for producing geometrically complex components with distinct microstructures. Although previous studies show recovery of high strength at room temperature, very few studies demonstrate successful properties at elevated temperatures required for industrial applications. Here, the objectives of this study are to present a post-build heat treatment for high strength across a wide temperature range, determine the strength contribution of nanoscale precipitating phases to the overall mechanical properties of superalloy 718, and from these, provide a comprehensive microstructure-property relationship for wrought and AM 718 to guide efforts to simulate the properties of AM components. Laser powder bed fusion–produced superalloy 718 was characterized at multiple length scales using scanning electron microscopy and transmission electron microscopy in the as-built condition and with multiple heat treatments designed to form combinations of γ', γ", and δ precipitates. Uniaxial tensile tests performed from room temperature to 600 °C on subsize specimens determined the yield strength, elastic modulus, ultimate tensile strength, fracture stress, and uniform elongation. Precipitates in this work proved to be weak barriers to dislocation motion through a dispersed barrier model, but they provided strength to the alloy through their consistent high density. The relative contribution to the yield strength from γ" remained consistent between 48% and 57% of the total strength up to 600 °C, the primary influence on the high temperature strength of superalloy 718. The strength factors for γ" and δ precipitates were found to trend inversely with tensile test temperature and may be attributable to the differences in precipitate coherency. A post-build heat treatment is recommended to maintain high strength at elevated temperatures. A quantitative microstructure-property relationship, dependent on precipitate size, density, and morphology, was derived and can estimate the yield strength across a wide temperature range applicable to the operational regimes for superalloy 718.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Effect of substrate temperature on sputter-deposited boron carbide films

Sputter deposition of B4C films with tailored physical properties remains a challenge. Here, we systematically study how substrate temperature influences the properties of B4C films deposited by direct current magnetron sputtering onto planar substrates held at temperatures in the range of 100-510°C. Results show that all films are amorphous stoichiometric B4C, with low O content of ~1 at. %. Films deposited onto substrates at 100°C exhibit high compressive residual stress and decreased mechanical properties. Therefore, for elevated substrate temperatures in the range of 180-510°C, film mass density, surface roughness, Young’s modulus, and hardness are weakly dependent on substrate temperature. However, in this temperature range, an increase in substrate temperature leads to larger residual compressive stress accompanied by a corresponding reduction in the concentration of nanoscale inhomogeneities. At least for the landing atom ballistics conditions studied here, a substrate temperature range of ~185-250°C is optimum for growing films with near-zero intrinsic residual stress. The overall weak substrate temperature dependence of film properties revealed in this work is favorable for the development of a robust deposition process, particularly for the case of deposition onto non-planar substrates where temperature control is often challenging.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Ab Initio Modeling of fcc Fe-Co-Cr-Ni High Entropy Alloys with Full Composition Range

The Fe-Co-Cr-Ni quaternary system has been studied extensively in the past decade, not only because of the superior properties achieved like high tensile ductility and fracture toughness, but also it is the foundation for the development of FeCrCoNi-based HEAs. However, most of the investigations are mainly focusing on the equiatomic and semi-equiatomic compositions. The physical properties of non-equiatomic compositions are barely explored. In the current work, the ab initio approach is adopted to predict the lattice parameter, structure stabilities, elastic properties, and enthalpy of formations of fcc Fe-Cr-Co-Ni HEA single crystals with the special quasirandom structure (SQS) method. To expand the design of Fe-Co-Cr-Ni HEAs into a full composition range, the current simulations cover all the binaries, ternaries, and the whole quaternary system. The 2-D composition-property contour diagrams are created to show the physical properties in the ternary and quaternary systems. Furthermore, our investigation shows that the fcc alloys' lattice parameter increases with the addition of Fe and Cr and decreases with Ni and Co. In addition to the enthalpy of formation at o K, the shape distortion rate is proposed to be another essential parameter to evaluate crystal stability. The results show the addition of Cr would destabilize the fcc lattice and cause symmetry breaking. Finally, the result of Pugh’s ratio shows that most of the fcc alloys show ductile behavior (P > 1.75), especially for the alloys around Fe 3 Ni, FeCo, and Fe 2 NiCo (P > 2.5). The brittle behavior (P < 1.75) is located around Fe 3 Cr and Fe 2 CoCr. Meanwhile, Cr 2 NiCo and Cr 2 FeNiCo are considered promising compositions to be tried and verified experimentally because of the higher bulk modulus and moderate shear modulus.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Spin Transitions and Compressibility of ε-Fe 7 N 3 and γ'-Fe 4 N: Implications for Iron Alloys in Terrestrial Planet Cores

Iron nitrides are possible constituents of the cores of Earth and other terrestrial planets. Pressure-induced magnetic changes in iron nitrides and effects on compressibility remain poorly understood. In this work, we report synchrotron X-ray emission spectroscopy (XES) and X-ray diffraction (XRD) results for ε-Fe 7 N 3 and γ'-Fe 4 N up to 60 GPa at 300 K. The XES spectra reveal completion of high- to low-spin transition in ε-Fe 7 N 3 and γ'-Fe 4 N at 43 and 34 GPa, respectively. The completion of the spin transition induces stiffening in bulk modulus of ε-Fe 7 N 3 by 22% at ~40 GPa, but has no resolvable effect on the compression behavior of γ'-Fe 4 N. Fitting pressure-volume data to the Birch-Murnaghan equation of state yields V 0 = 83.29 ± 0.03 (Å 3 ), K 0 = 232 ± 9 GPa, K 0 ' = 4.1 ± 0.5 for nonmagnetic ε-Fe 7 N 3 above the spin transition completion pressure, and V 0 = 54.82 ± 0.02 (Å 3 ), K 0 = 152 ± 2 GPa, K 0 ' = 4.0 ± 0.1 for γ'-Fe 4 N over the studied pressure range. By reexamining evidence for spin transition and effects on compressibility of other candidate components of terrestrial planet cores, Fe 3 S, Fe 3 P, Fe 7 C 3 , and Fe 3 C based on previous XES and XRD measurements, we located the completion of high- to low-spin transition at ~67, 38, 50, and 30 GPa at 300 K, respectively. The completion of spin transitions of Fe 3 S, Fe 3 P, and Fe 3 C induces elastic stiffening, whereas that of Fe 7 C 3 induces elastic softening. Changes in compressibility at completion of spin transitions in iron-light element alloys may influence the properties of Earth's and planetary cores.

58 GEOSCIENCES↗
DOE OSTI2023

Dark matter and dark radiation from the early universe with a modulus coupled to the PQMSSM

The supersymmetrized DFSZ axion model is especially compelling in that it contains 1. the SUSY solution to the gauge hierarchy problem, 2. the Peccei-Quinn (PQ) solution to the strong CP problem and 3. the Kim-Nilles solution to the SUSY μ problem. In a string setting, where a discrete R-symmetry ($Z$$^{R}_{24}$ for example) may emerge from the compactification process, a high-quality accidental axion (accion) can emerge from the accidental, approximate remnant global U(1) PQ symmetry where the decay constant f a is linked to the SUSY breaking scale, and is within the cosmological sweet zone. In this setup, one also expects the presence of stringy remnant moduli fields Φ i . Here, we consider the situation of a single light modulus Φ coupled to the PQMSSM in the early universe, with mixed axion plus higgsino-like WIMP dark matter. We evaluate dark matter and dark radiation production via nine coupled Boltzmann equations and assess the severity of the cosmological moduli problem (CMP) along with dark matter and dark radiation production rates. We find that typically the light modulus mass should be m Φ ≳ 10 4 TeV to avoid the moduli-induced dark matter overproduction problem. If one is able to (anthropically) tune the modulus field amplitude, we find a value of Φ 0 ≲ 10 –7 m P would be required to solve the overall CMP.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2023

Molecular-Dynamics Analysis of the Mechanical Behavior of Plasma-Facing Tungsten

We report a systematic computational analysis of the mechanical behavior of plasma-facing component (PFC) tungsten focusing on the impact of void and helium (He) bubble defects on the mechanical response beyond the elastic regime. Specifically, we explore the effects of porosity and He atomic fraction on the mechanical properties and structural response of PFC tungsten, at varying temperature and bubble size. We find that the Young modulus of defective tungsten undergoes substantial softening that follows an exponential scaling relation as a function of matrix porosity and He atomic content. Beyond the elastic regime, our high strain rate simulations reveal that the presence of nanoscale spherical defects (empty voids and He bubbles) reduces the yield strength of tungsten in a monotonically decreasing fashion, obeying an exponential scaling relation as a function of tungsten matrix porosity and He concentration. Our detailed analysis of the structural response of PFC tungsten near the yield point reveals that yielding is initiated by emission of dislocation loops from bubble/matrix interfaces, mainly 1/2<111> shear loops, followed by gliding and growth of these loops and reactions to form <100> dislocations. Furthermore, dislocation gliding on the <111>{211} twin systems nucleates 1/6<111> twin regions in the tungsten matrix. These dynamical processes reduce the stress in the matrix substantially. Subsequent dislocation interactions and depletion of the twin phases via nucleation and propagation of detwinning partials lead the tungsten matrix to a next deformation stage characterized by stress increase during applied straining. Furthermore, our structural analysis reveals that the depletion of twin boundaries (areal defects) is strongly impacted by the density of He bubbles at higher porosities. After the initial stress relief upon yielding, increase in the dislocation density in conjunction with decrease in the areal defect density facilitates the initiation of dislocation-driven deformation mechanisms in the PFC crystal.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Irradiation-induced damage in concrete-forming aggregates: revisiting literature data through micromechanics

The radiation-induced volumetric expansion (RIVE) of aggregate-forming minerals causes damage in concrete exposed to high levels of fast neutrons fluence ( \(>\,\sim \,10^{19}\, \hbox {n}\,\hbox {cm}^{-2}\) at kinetics energy above 0.1 MeV). Historical post-irradiation RIVE and Young’s modulus data obtained in test reactors were revisited using a polycrystalline homogenization model (self-consistent scheme) accounting for the aggregates’ minerals content and the formation of voids/cracks during irradiation. It was found that the formation of extra voids/cracks can contribute to the aggregate expansion more substantially than the cumulated expansions of aggregate-forming minerals. Furthermore, the rate of void creation appears to be inversely correlated to the silica content, although aggregates of higher silicate contents exhibit higher RIVEs. The loss of Young’s modulus decreases exponentially with the aggregates’ expansion. At a comparable RIVE level, the relative loss of modulus is more significant in aggregates of higher silica content.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Poly(vinyl alcohol) Hydrogels with Broad-Range Tunable Mechanical Properties via the Hofmeister Effect

Hydrogels, exhibiting wide applications in soft robotics, tissue engineering, implantable electronics, etc., often require sophisticately tailoring of the hydrogel mechanical properties to meet specific demands. For examples, soft robotics necessitates tough hydrogels; stem cell culturing demands various tissue-matching modulus; and neuron probes desire dynamically tunable modulus. Herein, a strategy to broadly alter the mechanical properties of hydrogels reversibly via tuning the aggregation states of the polymer chains by ions based on the Hofmeister effect is reported. An ultratough poly(vinyl alcohol) (PVA) hydrogel as an exemplary material (toughness 150 ± 20 MJ m -3 ), which surpasses synthetic polymers like poly(dimethylsiloxane), synthetic rubber, and natural spider silk is fabricated. With various ions, the hydrogel's various mechanical properties are continuously and reversibly in situ modulated over a large window: tensile strength from 50 ± 9 kPa to 15 ± 1 MPa, toughness from 0.0167 ± 0.003 to 150 ± 20 MJ m -3 , elongation from 300 ± 100% to 2100 ± 300%, and modulus from 24 ± 2 to 2500 ± 140 kPa. Importantly, the ions serve as gelation triggers and property modulators only, not necessarily required to remain in the gel, maintaining the high biocompatibility of PVA without excess ions. Overall, this strategy, enabling high mechanical performance and broad dynamic tunability, presents a universal platform for broad applications from biomedicine to wearable electronics.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Penta-SiCN: A Highly Auxetic Monolayer

We report the negative Poisson’s (NPR) ratio in a two-dimensional (2D) material is a counterintuitive mechanical property that facilitates the development of nanoscale devices with sophisticated functionality. Inspired by the peculiar buckled lower-symmetric, trilayered geometry of pentagonal monolayers, we theoretically predict penta-SiCN, a ternary auxetic metallic monolayer with highly tunable NPR. The penta-SiCN is structurally, thermally, dynamically, and mechanically stable, and sustainable at and beyond room temperature with experimental feasibility. It possesses nontrivial geometrical and mechanical isotropy and relatively moderate thickness. Remarkably, the shorter and quasi sp3-hybridized C–N bond and the rigidity against the strain allow the monolayer to possess a high value of NPR (-0.136), even higher than that of black phosphorene, extendable up to -0.639 by 4% of biaxial stretching. On the other hand, the 2D Young’s modulus of 129.88 N/m decreases to 41.34 N/m at equivalent stretching, indicating relative softening and flexibility. Interestingly, a buckled-to-planar phase transition is identified at 10% biaxial strain before it suffers the fracture at 16%. Additionally, the strong optical anisotropy, absorbance (up to 6.51 x 105 cm -1 ), and presence of plasmon frequency demonstrate its potential application in optomechanical and plasmonics.

36 MATERIALS SCIENCE↗