Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “high harmonic generation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

An expert system to analyze high frequency dependent data for the space shuttle main engine turbopumps

The prototype expert system ADDAMX identifies selected sinusoid frequencies from spectral data graphs as speed frequencies and harmonics from each turbopump, frequency feed through from one turbopump to another, frequencies generated by turbopump bearings, pseudo 3N for the phase 2 high pressure fuel turbopump, and electrical noise. ADDAMX does the analysis in an interactive or batch mode and the results can be displayed on the screen or hardcopy.

Garcia, Raul C., Jr.↗
DOE OSTI2026

Nonlinear regenerative amplification using tunable intracavity cascaded quadratic nonlinearities

Conventional nonlinear regenerative amplification utilizes Kerr (i.e., self-focusing) nonlinearity to broaden the spectrum via self-phase modulation during the direct amplification of ultrashort pulses, which helps overcome spectral gain narrowing for high-energy, ultrashort-pulse generation. We introduce cascaded quadratic nonlinearities from a type-I second-harmonic generation crystal, which can be tuned in both magnitude and sign via the phase-mismatching condition, inside a regenerative amplifier to enable nonlinearity-tunable regenerative amplification. We demonstrate, both experimentally and numerically, a nonlinear Yb:YAG thin-disk regenerative amplifier with either positive or negative net nonlinearity that delivers 1-kHz, >0.4-mJ pulses as short as ∼200 fs and high-quality beams free of self-focusing. The laser’s average power can be scaled to >100 W when seeded and operated at a much higher repetition rate to benefit various applications.

47 OTHER INSTRUMENTATION↗
NASA NTRS2003

A High Power Frequency Doubled Fiber Laser

This slide presentation reviews the power frequencies for the doubled fiber laser. It includes information on the 780 nm laser, second harmonic generation in one crystal, cascading crystals, the tenability of laser systems, laser cooling, and directions for future work.

high power lasers↗
DOE OSTI2020

Room-Temperature Ferroelectric LiNb 6 Ba 5 Ti 4 O 30 Spinel Phase in a Nanocomposite Thin Film Form for Nonlinear Photonics

Tetragonal tungsten bronze (TTB) materials are one of the most promising classes of materials for ferroelectric and nonlinear optical devices, owing to their very unique noncentrosymmetric crystal structure. In this work, a new TTB phase of LiNb 6 Ba 5 Ti 4 O 30 (LNBTO) has been discovered and studied. A small amount of a secondary phase, LiTiO 2 (LTO), has been incorporated as nanopillars that are vertically embedded in the LNBTO matrix. The new multifunctional nanocomposite thin film presents exotic highly anisotropic microstructure and properties, e.g., strong ferroelectricity, high optical transparency, anisotropic dielectric function, and strong optical nonlinearity evidenced by the second harmonic generation results. An optical waveguide structure based on the stacks of α-Si on SiO 2 /LNBTO–LTO has been fabricated, exhibiting low optical dispersion with an optimized evanescent field staying in the LNBTO–LTO active layer. Lastly, this work highlights the combination of new TTB material designs and vertically aligned nanocomposite structures for further enhanced anisotropic and nonlinear properties.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Switchable planar chirality and spin texture in highly ordered ferroelectric hybrid perovskite domains

Chiral organic-inorganic hybrid perovskites offer a promising platform for developing non-linear chiro-optical applications and chiral-induced spin selectivity. Here, we show that achiral hybrid perovskites that have highly ordered ferroelectric domains with orthogonal polarization exhibit planar chirality, as manifested by second harmonic generation with strong circular dichroism. Interestingly, the handedness of the second harmonic generation circular dichroism response can be alternatingly switched between orthogonally polarized domains and domain walls. To correlate the origin of planar chirality in these domains, atom-resolved atomic force microscopy is used to reveal distinct arrangements of atomic rows in these ferroelectric crystals that indicate planar symmetry breaking. Remarkably, a large SHG anisotropy factor of 0.41 is measured at the domain wall. Additionally, spatially resolved two-photon photoluminescence excitation measurement provide evidence of larger Rashba spin-splitting in these chiral ferroelectric domains compared to domain-free areas. Our discoveries of domain-dependent planar chirality and spin texture hold great promise for advancement of domain-specific chiro-optical applications.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Control of second-harmonic generation in all-dielectric intersubband metasurfaces by controlling the polarity of χ (2)

All-dielectric metasurfaces have recently led to a paradigm shift in nonlinear optics as they allow for circumventing the phase matching constraints of bulk crystals and offer high nonlinear conversion efficiencies when normalized by the light-matter interaction volume. Unlike bulk crystals, in all-dielectric metasurfaces nonlinear conversion efficiencies primarily rely on the material nonlinearity, field enhancements, and the modal overlaps, therefore most efforts to date have only focused on utilizing these degrees of freedom. In this work, we demonstrate that for second-harmonic generation in all-dielectric metasurfaces, an additional degree of freedom is the control of the polarity of the nonlinear susceptibility. We demonstrate that semiconductor heterostructures that support resonant nonlinearities based on quantum-engineered intersubband transitions provide this new degree of freedom. We can flip and control the polarity of the nonlinear susceptibility of the dielectric medium along the growth direction and couple it to the Mie-type photonic modes. Here we demonstrate that engineering the χ (2) polarity in the meta-atom enables the control of the second-harmonic radiation pattern and conversion efficiency. Our results therefore open a new direction for engineering and optimizing second-harmonic generation using all-dielectric intersubband nonlinear metasurfaces.

42 ENGINEERING↗
DOE OSTI2023

MgSiP 2 : An Infrared Nonlinear Optical Crystal with a Large Non‐Resonant Phase‐Matchable Second Harmonic Coefficient and High Laser Damage Threshold

Superior infrared nonlinear optical (NLO) crystals are in urgent demand in the development of lasers and optical technologies for communications and computing. The critical challenge is to find a crystal with large non‐resonant phase‐matchable NLO coefficients and high laser damage threshold (LDTs) simultaneously, which however scale inversely. This work reports such a material, MgSiP 2, that exhibits a large second harmonic generation (SHG) coefficient of d 14 ≈ d 36 = 89 ± 5 pm V −1 at 1550 nm fundamental wavelength, surpassing the commercial NLO crystals AgGaS 2 , AgGaSe 2 , and ZnGeP 2 . First principles theory reveals the polarizability and geometric arrangement of the [SiP 4 ] tetrahedral units as the origin of this large nonlinear response. Remarkably, it also exhibits a high LDT value of 684 GW cm −2 , which is six times larger than ZnGeP 2 and three times larger than CdSiP 2 . It has a wide transparency window of 0.53–10.35 µm, allowing broadband tunability. Further, it is Type I and Type II phase‐matchable with large effective SHG coefficients of d eff,I ≈80.2 pm V −1 and d eff,II ≈73.4 pm V −1 . The outstanding properties of MgSiP 2 make it a highly attractive candidate for optical frequency conversion in the infrared.

36 MATERIALS SCIENCE↗
DOE OSTI2024

2023 Billion-Ton Report: An Assessment of U.S. Renewable Carbon Resources - Microalgae

Microalgae is a unique biomass resource that does not need to compete for land and water with other biomass feedstocks because it can be cultivated on low-quality unencumbered land using noncompetitive water types including saline and wastewater. It is included as a complementary resource alongside other biomass feedstocks reported in this study, albeit at higher biomass production costs reflective of more capital-intensive farming operations than typical for terrestrial biomass. Higher biomass costs can be offset by the potential to produce value-added coproducts unique to compositional constituents of microalgae. Relative to the 2016 Billion-Ton Report, this chapter reflects the latest analysis from the 2022 Algae Harmonization Update, which uses the latest parameterized and high-performing saline algal strain, second-generation carbon capture of point-source waste CO 2 , and high-pressure pipeline transport resolved to specific point-source types, saline water sourcing up to 40,000 mg/L total dissolved solids for source and makeup water salinity, blowdown water treatment and recycle, and brine disposal handling. National-scale algal biomass availability potential was calculated at 152 million tons/yr ash-free dry weight (AFDW) (191 million tons/yr dry weight) at an average biomass

09 BIOMASS FUELS↗
DOE OSTI2024

Chapter 7.1: Microalgae

Microalgae is a unique biomass resource that does not need to compete for land and water with other biomass feedstocks because it can be cultivated on low-quality unencumbered land using noncompetitive water types including saline and wastewater. It is included as a complementary resource alongside other biomass feedstocks reported in this study, albeit at higher biomass production costs reflective of more capital-intensive farming operations than typical for terrestrial biomass. Higher biomass costs can be offset by the potential to produce value-added coproducts unique to compositional constituents of microalgae. Relative to BT16, this chapter reflects the latest analysis from the 2022 Algae Harmonization Update, which uses the latest parameterized and high-performing saline algal strain, second-generation carbon capture of point-source waste CO2 and high-pressure pipeline transport resolved to specific point-source types, saline water sourcing up to 40,000 mg/L total dissolved solids for source and makeup water salinity, blowdown water treatment and recycle, and brine disposal handling. National-scale algal biomass availability potential was calculated at 152 million tons/yr ash-free dry weight (AFDW) (191 million tons/yr dry weight) at an average biomass productivity of 26.2 g/m2 -day AFDW (about 50 tons/acre/yr dry weight).1 The algal biomass was cultivated on 3.9 million acres of multi-criteria screened and potentially available land for CONUS and fixed 268 million tons of waste CO2 based on biomass uptake. The algae biomass can be produced at an average MBSP of $674/ton AFDW ($536/ton dry weight) in 2020 dollars,2 corresponding to a total energy potential of 3.3 quads/yr at an average MBSP of $31.2/MMBtu (higher-heating-value [HHV] basis).

algae↗
NASA NTRS1989

In-flight measurement of propeller noise on the fuselage of an airplane

In-flight measurements of propeller noise on the fuselage of an OV-10A aircraft were obtained using a horizontal and a vertical microphone array. A wide range of flight conditions were tested including changes in angle of attack, sideslip angle, power coefficient, helical tip Mach number and advance ratio, and propeller direction of rotation. Results show a dependence of the level and directivity of the tones on the angle of attack and on the sideslip angle with the propeller direction of rotation, which is similar to results obtained in wind tunnel tests with advanced propeller designs. The level of the tones at each microphone increases with increasing angle of attack for inboard-down propeller rotation and decreases for inboard-up rotation. The level also increases with increasing slideslip angle for both propeller directions of rotation. Increasing the power coefficient results in a slight increase in the level of the tones. A strong shock wave is generated by the propeller blades even at relatively low helical tip Mach numbers resulting in high harmonic levels. As the helical tip Mach number and the advance ratio are increased, the level of the higher harmonics increases much faster than the level of the blade passage frequency.

Pla, Frederic G.↗
DOE OSTI2024

Millimeter-Scale Exfoliation of hBN with Tunable Flake Thickness for Scalable Encapsulation

As a two-dimensional (2D) dielectric material, hexagonal boron nitride (hBN) is in high demand for applications in photonics, nonlinear optics, and nanoelectronics. Unfortunately, the high-throughput preparation of macroscopic-scale, high-quality hBN flakes with controlled thickness is an ongoing challenge, limiting device fabrication and technological integration. In this report we present a metal thin-film exfoliation method to prepare hBN flakes with millimeter-scale dimension, near-unity yields, and tunable flake thickness distribution from 1-7 layers, a substantial improvement over scotch tape exfoliation. The single crystallinity and high quality of the exfoliated hBN are demonstrated with optical microscopy, atomic force microscopy, Raman spectroscopy, and second harmonic generation. We further explore a possible mechanism for the effectiveness and selectivity based on thin-film residual stress measurements, density functional theory calculations, and transmission electron microscopy imaging of the deposited metal films. We find that the magnitude of the residual tensile stress induced by thin film deposition plays a key role in determining exfoliated flake thickness in a manner which closely resembles 3D semiconductor spalling. Lastly, we demonstrate that our exfoliated, large-area hBN flakes can be readily incorporated as encapsulating layers for other 2D monolayers. Altogether, this method brings us one step closer to the high throughput, mass production of hBN-based 2D photonic, optoelectronic, and quantum devices.

2D materials↗
DOE OSTI2023

Ferrorotational domain walls revealed by electric quadrupole second harmonic generation microscopy

Domain walls are ubiquitous in materials that undergo phase transitions driven by spontaneous symmetry breaking. Domain walls in ferroics and multiferroics have received tremendous attention recently due to their emergent properties distinct from their domain counterparts—for example, their high mobility and controllability, as well as their potential applications in nanoelectronics. However, it is extremely challenging to detect, visualize, and study the ferrorotational (FR) domain walls because the FR order, in contrast to ferromagnetism and ferroelectricity, is invariant under both the spatial-inversion and the time-reversal operations and, thus, hardly couple with conventional experimental probes. Here, a FR candidate NiTi⁢O 3 is investigated by ultrasensitive electric quadrupole (EQ) second-harmonic generation rotational anisotropy (SHG RA) to probe the point symmetries of the two degenerate FR domain states, showing their relation by the vertical mirror operations that are broken below the FR critical temperature. We then visualize the real-space FR domains by scanning EQ SHG microscopy, and further, resolve the FR domain walls by revealing a suppressed SHG intensity at the domain walls. By taking local EQ SHG RA measurements, we show the restoration of the mirror symmetry at FR domain walls and prove their unconventional nonpolar nature. In conclusion, our findings not only provide a comprehensive insight into FR domain walls, but also demonstrate a unique and powerful tool for future studies on domain walls of unconventional ferroics both of which pave the way towards future manipulations and applications of FR domain walls.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS1998

Efficient Third Harmonic Generation for Wind Lidar Applications

The characterization of atmospheric winds on a global basis is a key parameter required for accurate weather prediction. The use of a space based lidar system for remote measurement of wind speed would provide detailed and highly accurate data for future weather prediction models. This paper reports the demonstration of efficient third harmonic conversion of a 1 micrometer laser to provide an ultraviolet (UV) source suitable for a wind lidar system based on atmospheric molecular scattering. Although infrared based lidars using aerosol scattering have been demonstrated to provide accurate wind measurement, a UV based system using molecular or Rayleigh scattering will provide accurate global wind measurements, even in those areas of the atmosphere where the aerosol density is too low to yield good infrared backscatter signals. The overall objective of this work is to demonstrate the maturity of the laser technology and its suitability for a near term flight aboard the space shuttle. The laser source is based on diode-pumped solid-state laser technology which has been extensively demonstrated at TRW in a variety of programs and internal development efforts. The pump laser used for the third harmonic demonstration is a breadboard system, designated the Laser for Risk Reduction Experiments (LARRE), which has been operating regularly for over 5 years. The laser technology has been further refined in an engineering model designated as the Compact Advanced Pulsed Solid-State Laser (CAPSSL), in which the laser head was packaged into an 8 x 8 x 18 inch volume with a weight of approximately 61 pounds. The CAPSSL system is a ruggedized configuration suitable for typical military applications. The LARRE and CAPSSL systems are based on Nd:YAG with an output wavelength of 1064 nm. The current work proves the viability of converting the Nd:YAG fundamental to the third harmonic wavelength at 355 nm for use in a direct detection wind lidar based on atmospheric Rayleigh scattering.

Mordaunt, David W.↗
DOE OSTI2022

Direct visualization and control of antiferromagnetic domains and spin reorientation in a parent cuprate

Here, we report magnetic optical second-harmonic generation (SHG) polarimetry and imaging on Sr 2 Cu 3 O 4 Cl 2 , which allows direct visualization of the mesoscopic antiferromagnetic (AFM) structure of a parent cuprate. Temperature- and magnetic-field-dependent SHG reveals large domains with 90° relative orientations that are stabilized by a combination of uniaxial magnetic anisotropy and the Earth's magnetic field. Below a temperature T R ~ 97 K, we observe an unusual 90° spin reorientation transition, possibly driven by competing magnetic anisotropies of the two copper sublattices, which swaps the AFM domain states while preserving the domain structure. This allows deterministic switching of the AFM states by thermal or laser heating. Near T R , the domain walls become exceptionally responsive to an applied magnetic field, with the Earth's field sufficient to completely expel them from the crystal. Our findings unlock opportunities to study the mesoscopic AFM behavior of parent cuprates and explore their potential for AFM technologies.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

Stabilization of the Polar Structure and Giant Second-Order Nonlinear Response of Single Crystal γ-NaAs 0.95 Sb 0.05 Se 2

The dearth of suitable materials significantly restricts the practical development of infrared (IR) laser systems with highly efficient and broadband tuning. Recently, γ-NaAsSe 2 is reported, and it exhibits a large nonlinear second-harmonic generation (SHG) coefficient of 590 pm V —1 at 2 µm. However, the crystal growth of γ-NaAsSe 2 is challenging because it undergoes a phase transition to centrosymmetric δ-NaAsSe 2 . Herein, the stabilization of non-centrosymmetric γ-NaAsSe 2 by doping the As site with Sb, which results in γ-NaAs 0.95 Sb 0.05 Se 2 is reported. The congruent melting behavior is confirmed by differential thermal analysis with a melting temperature of 450 °C and crystallization temperature of 415 °C. Single crystals with dimensions of 3 mm × 2 mm are successfully obtained via zone refining and the Bridgman method. The purification of the material plays a significant role in crystal growth and results in a bandgap of 1.78 eV and thermal conductivity of 0.79 Wm —1 K —1 . The single-crystal SHG coefficient of γ-NaAs 0.95 Sb 0.05 Se 2 exhibits an enormous value of |d 11 | = 648 ± 74 pm V —1 , which is comparable to that of γ-NaAsSe 2 and ≈20× larger than that of AgGaSe 2 . Importantly, the bandgap of γ-NaAs 0.95 Sb 0.05 Se 2 (1.78 eV) is similar to that of AgGaSe 2 , thus rendering it highly attractive as a high-performing nonlinear optical material.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Crystal Structures, Optical Behavior, and Magnetic Properties in Hydrated Lanthanide Iron Sulfates

Single crystals of LnFe(SO 4 ) 3 (H 2 O) 2 (Ln = La, Ce, Pr, Nd, Sm, Eu, Gd, Dy, Ho, Er, Tm; compounds 1–11) and LnFe(SO 4 ) 3 (H 2 O) (Ln = Tm, Yb, Lu; compounds 12–14) were synthesized under hydrothermal conditions. Single-crystal X-ray diffraction (SCXRD) analysis revealed that the dihydrated compounds (1–11) crystallize in centrosymmetric (CS) structures, with the lanthanide ions adopting eight-coordinate geometries. In contrast, the monohydrated compounds (12–14) exhibit noncentrosymmetric (NCS) structures, where the lanthanide ions are seven-coordinated. Vibrating sample magnetometry (VSM) confirmed that compounds 2, 4, and 7–11 are paramagnetic below 400 K, with compound 8 displaying the highest magnetic susceptibility. Compounds 1, 5, 6, 13, and 14 show a sharp increase in magnetic susceptibility at Néel temperatures ( T N ) of approximately 72, 76, 70, 58, and 56 K, respectively, indicating antiferromagnetic ordering. High-temperature magnetic susceptibility measurements further support the presence of antiferromagnetic transitions in these compounds. Second harmonic generation (SHG) measurements showed that the noncentrosymmetric Yb (compound 13) and Lu (compound 14) compounds exhibit SHG intensities of 0.3× and 1.6× that of potassium dihydrogen phosphate (KDP), respectively.

anions↗