Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “grain boundary diffusion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

Well-isolated L1{sub 0} FePt-SiN{sub x}-C nanocomposite films with large coercivity and small grain size

FePt-SiN{sub x}-C films on TiN/CrRu/glass substrate with large coercivity, (001) texture, and small isolated grains were obtained by co-sputtering FePt, Si{sub 3}N{sub 4}, and C targets at 380 deg. C. It was found that when C was doped into the FePt-SiN{sub x} films, the out-of-plane coercivity increased while the small in-plane coercivity remained unchanged. Grain size decreased and grain size distribution became more uniform with increasing the C doping concentration. The x-ray photoelectron spectroscopy (XPS) depth profile showed a uniform depth distribution of Si in the FePt layer. The Si2p XPS spectrum implied the existence of Fe-Si bonds, indicating that SiN{sub x} was located at the FePt grain boundaries and was stable against diffusion to the surface, thus favoring grain isolation. Well-isolated FePt (001) granular films with coercivity higher than 21.5 kOe and an average grain size of 5.6 nm were obtained by doping 40 vol. % of SiN{sub x} and 20 vol. % of C.

36 MATERIALS SCIENCE↗

Defect- and Strain-enhanced Cavity Formation and Au Precipitation at nano-crystalline ZrO2/SiO2/Si Interfaces

Defect- and strain-enhanced cavity formation and Au precipitation at the interfaces of a nanocrystalline ZrO2/SiO2/Si multilayer structure resulting from 2 MeV Au+ irradiation at temperatures of 160 and 400 K have been studied. Under irradiation, loss of oxygen is observed, and the nanocrystalline grains in the ZrO2 layer increase in size. In addition, small cavities are observed at the ZrO2/SiO2 interface with the morphology of the cavities being dependent on the damage state of the underlying Si lattice. Elongated cavities are formed when crystallinity is still retained in the heavily-damaged Si substrate; however, the morphology of the cavities becomes spherical when the substrate is amorphized. With further irradiation, the cavities appear to become stabilized and begin to act as gettering sites for the Au. As the cavities become fully saturated with Au, the ZrO2/SiO2 interface then acts as a gettering site for the Au. Analysis of the results suggests that oxygen diffusion along the grain boundaries contributes to the growth of cavities and that oxygen within the cavities may affect the gettering of Au. Mechanisms of defect- and strain-enhanced cavity formation and Au precipitation at the interfaces will be discussed with focus on oxygen diffusion and vacancy accumulation, the role of the lattice strain on the morphology of the cavities, and the effect of the binding free energy of the cavities on the Au precipitation.

36 MATERIALS SCIENCE↗

Grain Boundary Effects on Radiation Damage and Tritium Diffusion in Li–Al–O Ceramics from Molecular Dynamics and Experiments

Understanding irradiation damage and tritium transport in LiAlO2 ceramics is essential for their deployment in tritium-producing burnable absorber rods (TPBARs). Grain boundaries (GBs) play an important role in governing radiation response and tritium transport in LiAlO2 and its secondary phase LiAl5O8. Using molecular dynamics simulations, we investigated defect evolution and tritium diffusion during displacement cascades in single-crystal and bicrystal LiAlO2 and LiAl5O8 at 600 K. The results reveal that GBs suppress the damage in the LiAlO2 bicrystals as compared to single crystals, via interstitial emission. The effect is more pronounced for Li defects, than for Al and O. In LiAl5O8 the damage reduction due to introduction of GB is less pronounced overall. Tritium diffusion coefficients at GBs are higher by factors of 2–10 relative to diffusion inside grain bulk. The effect is particularly pronounced in LiAlO2, where S5, S17, and S25 GBs promote rapid tritium transport, whereas LiAl5O8 exhibits slower diffusion due to reduced free volume at its GBs. These findings evince a trade-off that while GBs mitigate radiation damage by absorbing interstitials, they simultaneously provide fast pathways for tritium migration which is not desirable for TPBAR application. The mechanistic insights gained here establish a foundation for microstructural design strategies to balance radiation tolerance and tritium retention in ceramic breeder materials.

Roy, Ankit↗

Analysis of Al diffusion processes in TiN barrier layers for the application in silicon solar cell metallization

An evaporated Al layer is known as an excellent rear metallization for highly efficient solar cells, but suffers from incompatibility with a common solder process. To enable solar cell-interconnection and module integration, in this work the Al layer is complemented with a solder stack of TiN/Ti/Ag or TiN/NiV/Ag, in which the TiN layer acts as an Al diffusion barrier. X-ray photoelectron spectroscopy measurements prove that diffusion of Al through the stack and the formation of an Al{sub 2}O{sub 3} layer on the stack's surface are responsible for a loss of solderability after a strong post-metallization anneal, which is often mandatory to improve contact resistance and passivation quality. An optimization of the reactive TiN sputter process results in a densification of the TiN layer, which improves its barrier quality against Al diffusion. However, measurements with X-ray diffraction and scanning electron microscopy show that small grains with vertical grain boundaries persist, which still offer fast diffusion paths. Therefore, the concept of stuffing is introduced. By incorporating oxygen into the grain boundaries of the sputtered TiN layer, Al diffusion is strongly reduced as confirmed by secondary ion mass spectroscopy profiles. A quantitative analysis reveals a one order of magnitude lower Al diffusion coefficient for stuffed TiN layers. This metallization system maintains its solderability even after strong post-metallization annealing at 425 °C for 15 min. This paper thus presents an industrially feasible, conventionally solderable, and long-term stable metallization scheme for highly efficient silicon solar cells.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Ultrafast Imaging of Carrier Transport across Grain Boundaries in Hybrid Perovskite Thin Films

For optoelectronic devices based on polycrystalline semiconducting thin films, carrier transport across grain boundaries is an important process in defining efficiency. Here we employ transient absorption microscopy (TAM) to directly measure carrier transport within and across the boundaries in hybrid organic-inorganic perovskite thin films for solar cell applications with 50 nm spatial precision and 300 fs temporal resolution. By selectively imaging sub-bandgap states, our results show that lateral carrier transport is slowed down by these states at the grain boundaries. However, the long carrier lifetimes allow for efficient transport across the grain boundaries. The carrier diffusion constant is reduced by about a factor of 2 for micron-sized grain samples by the grain boundaries. For grain sizes on the order of ~200 nm, carrier transport over multiple grains has been observed within a time window of 5 ns. These observations explain both the shortened photoluminescence lifetimes at the boundaries as well as the seemingly benign nature of the grain boundaries in carrier generation.

14 SOLAR ENERGY↗

YSZ thin films with minimized grain boundary resistivity

In recent years, interface engineering of solid electrolytes has been explored to increase their ionic conductivity and improve the performance of solid oxide fuel cells and other electrochemical power sources. It has been observed that the ionic conductivity of epitaxially grown thin films of some electrolytes is dramatically enhanced, which is often attributed to effects (e.g. strain-induced mobility changes) at the heterophase boundary with the substrate. Still largely unexplored is the possibility of manipulation of grain boundary resistivity in polycrystalline solid electrolyte films, clearly a limiting factor in their ionic conductivity. Here in this paper, we report that the ionic conductivity of yttria stabilized zirconia thin films with nano-columnar grains grown on a MgO substrate nearly reaches that of the corresponding single crystal when the thickness of the films becomes less than roughly 8 nm (smaller by a factor of three at 500 °C). Using impedance spectroscopy, the grain boundary resistivity was probed as a function of film thickness. The resistivity of the grain boundaries near the film–substrate interface and film surface (within 4 nm of each) was almost entirely eliminated. This minimization of grain boundary resistivity is attributed to Mg 2+ diffusion from the MgO substrate into the YSZ grain boundaries, which is supported by time of flight secondary ion mass spectroscopy measurements. We suggest grain boundary “design” as an attractive method to obtain highly conductive solid electrolyte thin films.

36 MATERIALS SCIENCE↗

Nucleation rate controlled grain boundary and lattice creep

Nucleation versus diffusion rate-limited bicrystal and single crystal creep exhibit different scaling dependencies that enable the mechanisms to be isolated when measured as a function of sample size. It has recently been suggested that nucleation rate-limited kinetic models generally describe the non-Newtonian portion of the creep response well, but more direct evidence is required. This work analyzes the grain boundary creep response of UO 2 , a pyrochlore high entropy oxide, silver, and palladium, along with the lattice creep of silver using small-scale in situ loading in the transmission electron microscope. At small sizes, each system exhibits scale dependence associated with nucleation rate-limited kinetics. Fits of the data produce activation volumes on the order of a few Burgers vectors cubed with positive temperature coefficients as expected for nucleation kinetics. The activation enthalpies fall in the range of about 0.4 eV to 1.7 eV, being lower for the metals and higher for the oxides.

36 MATERIALS SCIENCE↗

Irradiation-induced grain growth in nanocrystalline reduced activation ferrite/martensite steel

In this work, we investigate the microstructure evolution of surface-nanocrystallized reduced activation ferrite/martensite steels upon high-dose helium ion irradiation (24.3 dpa). We report a significant irradiation-induced grain growth in the irradiated buried layer at a depth of 300–500 nm, rather than at the peak damage region (at a depth of ∼840 nm). This phenomenon can be explained by the thermal spike model: minimization of the grain boundary (GB) curvature resulting from atomic diffusion in the cascade center near GBs.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

The high temperature creep deformation of Si3N4-6Y2O3-2Al2O3

The creep properties of silicon nitride containing 6 wt percent yttria and 2 wt percent alumina have been determined in the temperature range 1573 to 1673 K. The stress exponent, n, in the equation epsilon dot varies as sigma sup n, was determined to be 2.00 + or - 0.15 and the true activation energy was found to be 692 + or - 25 kJ/mol. Transmission electron microscopy studies showed that deformation occurred in the grain boundary glassy phase accompanied by microcrack formation and cavitation. The steady state creep results are consistent with a diffusion controlled creep mechanism involving nitrogen diffusion through the grain boundary glassy phase.

Todd, J. A.↗

The high temperature creep deformation of Si3N4-6Y2O3-2Al2O3

The creep properties of silicon nitride containing 6 wt percent yttria and 2 wt percent alumina have been determined in the temperature range 1573 to 1673 K. The stress exponent, n, in the equation epsilon dot varies as sigma sup n, was determined to be 2.00 + or - 0.15 and the true activation energy was found to be 692 + or - 25 kJ/mol. Transmission electron microscopy studies showed that deformation occurred in the grain boundary glassy phase accompanied by microcrack formation and cavitation. The steady state creep results are consistent with a diffusion controlled creep mechanism involving nitrogen diffusion through the grain boundary glassy phase.

Todd, J. A.↗

Analysis of the electron-beam-induced current of a polycrystalline p-n junction when the diffusion lengths of the material on either side of a grain boundary differ

The short circuit current generated by the electron beam of a scanning electron microscope in p-n junctions is reduced by enhanced recombination at grain boundaries in polycrystalline material. Frequently, grain boundaries separate the semiconductor into regions possessing different minority carrier life times. This markedly affects the short circuit current I(sc) as a function of scanning distance from the grain boundary. It will be shown theoretically that (1) the minimum of the I(sc) in crossing the grain boundary with the scanning electron beam is shifted away from the grain boundary toward the region with smaller life time (shorter diffusion length), (2) the magnitude of the minimum differs markedly from those calculated under the assumption of equal diffusion lengths on either side of the grain boundary, and (3) the minimum disappears altogether for small surface recombination velocities (s less than 10,000 cm/s). These effects become negligible, however, for large recombination velocities s at grain boundaries. For p-type silicon this happens for s not less than 100,000 cm/s.

Von Roos, O.↗

Effect of microstructure on Na/+/ diffusion in beta alumina

The effect of microstructural features, such as grain size and orientation, on sodium ion diffusion in polycrystalline beta alumina is investigated; the ionic solid is suitable for use in high-energy and power density batteries. Two types of hot-pressed polycrystalline samples are studied, one with grains highly oriented in the direction normal to the pressing direction, the other with significantly less preferred orientation normal to the pressing direction. Results of the experimental assessments indicate that grain size and diffusion path tortuosity have little effect on diffusion kinetics, while grain boundary type and grain aspect ratio are important factors in determining the diffusion rate.

Sarian, S.↗

Quantized grain boundary states controls nanoparticle coalescence during crystallization

First order transitions like crystallization are ubiquitous in nature. Yet, mechanistic details of crystallization, i.e. polymorph selection during nucleation, details of particle aggregation, role of pre-alignment during aggregation, remain unclear. At variance with the commonly invoked oriented attachment hypothesis, we show many nanoparticles with different misorientations coalesce to form single crystals. The alignment of nanoparticles after contact irrespective of their initial misorientation is driven by extensive dislocation activity at the interface leading to disintegration of grain boundaries that is followed by surface diffusion aided neck growth and densification. Grain boundaries disintegrate because the classical Read-Shockley description breaks down at the nanoscale and only few discrete energy levels are allowed. This points to a revision of the scope of oriented attachment in crystal growth, and the role of grain boundaries during deformation and grain growth in nanocrystalline materials.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Observation of thermally etched grain boundaries with the FIB/TEM technique

Thermal etching is a method which is able to reveal and characterize grain boundaries, twins or dislocation structures and determine parameters such as grain boundary energies, surface diffusivities or study phase transformations in steels, intermetallics or ceramic materials. This method relies on the preferential transfer of matter away from grain boundaries on a polished sample during heating at high temperatures in an inert/vacuum atmosphere. The evaporation/diffusion of atoms at high temperatures results in the formation of grooves at the intersections of the planes of grain/twin boundaries with the polished surface. This work describes how the combined use of Focussed Ion Beam and Transmission Electron Microscopy can be used to characterize not only the grooves and their profile with the surface, but also the grain boundary line below the groove, this method being complementary to the commonly used scanning probe techniques. - Highlights: • Thermally etched low-carbon steel samples have been characterized by FIB/TEM • Grain boundary (GB) lines below the groove have been characterized in this way • Absence of ghost traces and large θ angle suggests that GB are not stationary but mobile • Observations correlate well with previous works and Mullins' investigations [22].

36 MATERIALS SCIENCE↗

Shear Deformation of Polycrystalline Wadsleyite up to 2100 K at 14–17 GPa using a Rotational Drickamer Apparatus (RDA)

Shear deformation experiments on polycrystalline wadsleyite (water content, -200-2200 H/10{sup 6} Si) have been conducted at 14.4-17.0 GPa, 1690-2100 K, and strain rates of 2.6-16 x 10{sup -5} s{sup -1} using a rotational Drickamer apparatus (RDA) at a synchrotron facility. The stress was measured from the orientation dependence of lattice spacing for the (013), (211), (141), (240) and (244) planes. On the basis of the mechanical and microstructural observations, we infer that deformation occurs by exponential creep through the Peierls mechanism at relatively low temperatures of 1690-2030 K. However, a sample deformed at the temperature of 2100 K showed significant grain-size reduction, and most of small grains are dislocation-free, although sub-boundaries were observed in some grains in the sample. We interpret these observations as evidence for dynamic recrystallization and that diffusion creep (and grain boundary sliding) plays an important role after dynamic recrystallization caused by power law creep. Consequently, the strength observed in the high-temperature conditions determined by the present study provides an important constraint on strength of diffusion creep and a lower limit for that of the power law dislocation creep. We conclude that the strength of wadsleyite in the power law dislocation creep is higher than or comparable to that of olivine and the strength of wadsleyite in the Peierls regime is similar to that of olivine.

58 GEOSCIENCES↗

Electronic and Geometric Contributors to Hydrogen Binding in Uranium Oxide Grain Boundaries

Hydrogen induced corrosion of uranium, which leads to the formation of toxic and pyrophoric UH 3 , raises significant safety concerns for long-term storage of nuclear materials. Previous work suggests hydrogen diffuses through the grain boundaries (GBs) of the passivating oxide layer to initiate hydriding reactions. However, the atomistic mechanisms underlying this phenomenon and the structural factors that control its initiation are not well understood. To address this knowledge gap, here we use a high-throughput density functional theory (DFT) workflow to investigate the adsorption of H and H 2 in the defective bulk UO 2 . Specifically, we have exhaustively investigated the adsorption of H (107 sites) and H 2 (26 sites) in three different coincident site lattice (CSL) GBs: Σ3, Σ5, and Σ9. Compared to the binding energies in pristine UO 2 , we observe significantly stronger hydrogen adsorption at these GB sites. Interestingly, we find that the trends in H and H 2 adsorption vary considerably across the three GB models. In particular, while a small number of sites in Σ5 and Σ9 show exothermic adsorption of H and H 2 , respectively, no such sites are found in Σ3. These results provide fundamental atomistic insights that could guide the development of future corrosion mitigation strategies for the storage of nuclear materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗