Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “extensions”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

Service-Life Extension of Explosive Escape Devices

Chemical and functional tests yield conservative service-life estimates. Approach to extension of service lives of explosive devices in aircraft escape system developed, supported by testing of representative candidate devices to evaluate quantitatively effects of service, age, and degradation, and to enable responsible, conservative service-life determinations. Five types of explosive components evaluated: rigid and flexible explosive transfer lines; one-way transfers; flexible, linear-shaped charges; and initiation-handles. Extension of service in realistic manner provides both cost savings and increased system reliability.

Bement, L. J.↗
NASA NTRS1986

Subreflector extension for improved efficiencies in Cassegrain antennas - GTD/PO analysis

Both offset and symmetric Cassegrain reflector antennas are used in satellite and ground communication systems. It is known that the subreflector diffraction can degrade the performance of these reflectors. A geometrical theory of diffraction/physical optics analysis technique is used to investigate the effects of the extended subreflector, beyond its optical rim, on the reflector efficiency and far-field patterns. Representative numerical results are shown for an offset Cassegrain reflector antenna with different feed illumination tapers and subreflector extensions. It is observed that for subreflector extensions as small as one wavelength, noticeable improvements in the overall efficiencies can be expected. Useful design data are generated for the efficiency curves and far-field patterns.

Rahmat-Samii, Yahya↗
NASA NTRS1987

Extension-twist coupling of composite circular tubes with application to tilt rotor blade design

This investigation was conducted to determine if twist deformation required for the design of full-scale extension-twist-coupled tilt-rotor blades can be achieved within material design limit loads, and to demonstrate the accuracy of a coupled-beam analysis in predicting twist deformations. Two extension-twist-coupled tilt-rotor blade designs were developed based on theoretically optimum aerodynamic twist distributions. The designs indicated a twist rate requirement of between .216 and .333 deg/in. Agreement between axial tests and analytical predictions was within 10 percent at design limit loads. Agreement between the torsion tests and predictions was within 11 percent.

Nixon, Mark W.↗
NASA NTRS1989

Bendable Extension For Abrasive-Jet Cleaning

Hard-to-reach places cleaned more easily. Extension for abrasive-jet apparatus bent to provide controlled abrasive cleaning of walls in deep cavities or other hard-to-reach places. Designed for controlled removal of penetrant inspection dyes from inside castings, extension tube also used for such general grit-blasting work as removal of scratches.

Mayer, Walter↗
NASA NTRS1988

Extension and validation of a method for locating damaged members in large space trusses

The damage location approach employs the control system capabilities for the structure to test the structure and measure the dynamic response. The measurements are then used in a system identification algorithm to produce a model of the damaged structure. The model is compared to one for the undamaged structure to find regions of reduced stiffness which indicate the location of damage. Kabe's 3,4 stiffness matrix adjustment method was the central identification algorithm. The strength of his method is that, with minimal data, it preserves the representation of the physical connectivity of the structure in the resulting model of the damaged truss. However, extensive storage and computational effort were required as a result. Extension of the damage location method to overcome these problems is the first part of the current work. The central system identification algorithm is replaced with the MSMT method of stiffness matrix adjustment which was previously derived by generalizing an optimal-update secant method form quasi-Newton approaches for nonlinear optimization. Validation of the extended damage location method is the second goal.

Smith, Suzanne Weaver↗
NASA NTRS1988

Application of triggered lightning numerical models to the F106B and extension to other aircraft

The goal of the F106B Thunderstorm Research Program is to characterize the lightning environment for aircraft in flight. This report describes the application of numerical electromagnetic models to this problem. Topics include: (1) Extensive application of linear triggered lightning to F106B data; (2) Electrostatic analysis of F106B field mill data; (3) Application of subgrid modeling to F106B nose region, including both static and nonlinear models; (4) Extension of F106B results to other aircraft of varying sizes and shapes; and (5) Application of nonlinear model to interaction of F106B with lightning leader-return stroke event.

Ng, Poh H.↗
NASA NTRS1989

Extensions and improvements on XTRAN3S

Improvements to the XTRAN3S computer program are summarized. Work on this code, for steady and unsteady aerodynamic and aeroelastic analysis in the transonic flow regime has concentrated on the following areas: (1) Maintenance of the XTRAN3S code, including correction of errors, enhancement of operational capability, and installation on the Cray X-MP system; (2) Extension of the vectorization concepts in XTRAN3S to include additional areas of the code for improved execution speed; (3) Modification of the XTRAN3S algorithm for improved numerical stability for swept, tapered wing cases and improved computational efficiency; and (4) Extension of the wing-only version of XTRAN3S to include pylon and nacelle or external store capability.

Borland, C. J.↗
NASA NTRS1989

Development of a finite element based delamination analysis for laminates subject to extension, bending, and torsion

Delamination is a common failure mode of laminated composite materials. This type of failure frequently occurs at the free edges of laminates where singular interlaminar stresses are developed due to the difference in Poisson's ratios between adjacent plies. Typically the delaminations develop between 90 degree plies and adjacent angle plies. Edge delamination has been studied by several investigators using a variety of techniques. Recently, Chan and Ochoa applied the quasi-three-dimensional finite element model to the analysis of a laminate subject to bending, extension, and torsion. This problem is of particular significance relative to the structural integrity of composite helicopter rotors. The task undertaken was to incorporate Chan and Ochoa's formulation into a Raju Q3DG program. The resulting program is capable of modeling extension, bending, and torsional mechanical loadings as well as thermal and hygroscopic loadings. The addition of the torsional and bending loading capability will provide the capability to perform a delamination analysis of a general unsymmetric laminate containing four cracks, each of a different length. The solutions obtained using this program are evaluated by comparing them with solutions from a full three-dimensional finite element solution. This comparison facilitates the assessment of three dimensional affects such as the warping constraint imposed by the load frame grips. It wlso facilitates the evaluation of the external load representation employed in the Q3D formulation. Finally, strain energy release rates computed from the three-dimensional results are compared with those predicted using the quasi-three-dimensional formulation.

Hooper, Steven J.↗
NASA NTRS1989

Extension-torsion coupling behavior of advanced composite tilt-rotor blades

An analytic model was developed to study the extension-bend-twist coupling behavior of an advanced composite helicopter or tilt-rotor blade. The outer surface of the blade is defined by rotating an arbitrary cross section about an initial twist axis. The cross section can be nonhomogeneous and composed of generally anisotropic materials. The model is developed based upon a three dimensional elasticity approach that is recast as a coupled two-dimensional boundary value problem defined in a curvilinear coordinate system. Displacement solutions are written in terms of known functions that represent extension, bending, and twisting and unknown functions for local cross section deformations. The unknown local deformation functions are determined by applying the principle of minimum potential energy to the discretized two-dimensional cross section. This is an application of the Ritz method, where the trial function family is the displacement field associated with a finite element (8-node isoparametric quadrilaterals) representation of the section. A computer program was written where the cross section is discretized into 8-node quadrilateral subregions. Initially the program was verified using previously published results (both three-dimensional elasticity and technical beam theory) for pretwisted isotropic bars with an elliptical cross section. In addition, solid and thin-wall multi-cell NACA-0012 airfoil sections were analyzed to illustrate the pronounced effects that pretwist, initial twist axis location, and spar location has on coupled behavior. Currently, a series of advanced composite airfoils are being modeled in order to assess how the use of laminated composite materials interacts with pretwist to alter the coupling behavior of the blade. These studies will investigate the use of different ply angle orientations and the use of symmetric versus unsymmetric laminates.

Kosmatka, J. B.↗
NASA NTRS1989

Extension during continental convergence, with application to the Tibetan Plateau

An explanation in terms of the thermal evolution of thickened continental lithosphere is offered to explain the transition, in the late Tertiary to Quaternary, from north-south compression to east-west extension in the strain rate field of the Tibetan Plateau. The lower part of the lithosphere consists of a thermal boundary layer which, when thickened by horizontal shortening, is colder and denser than its surroundings. Convective instability of the thickened thermal boundary layer and its replacement by hot asthenosphere would rapidly raise the surface elevation and gravitational potential energy of the overlying part of the lithosphere. The convective instability would happen in a time brief compared with the collision time scale but would only occur after there had already been substantial thickening of the lithosphere. The increase in surface height and of potential energy are sufficient for east-west extension to replace north-south compression as the dominant feature of the stress field.

England, Philip↗
NASA NTRS1991

Mean flow and variability in the Kuroshio Extension from Geosat altimetry data

The mean flow and temporal and spatial variations of the Kuroshio Extension in the region of 140-180 deg E and 30-40 deg N are investigated using altimeter data from the Geosat Exact Repeat Mission (ERM). Mean surface height profiles are estimated along individual tracks by assuming the velocity profile of the Kuroshio Extension to be Gaussian-shaped and by successively fitting this synthetic current's height profile to the residual height data. The mean profiles from ascending and descending tracks are used to derive the mean surface height by an inverse method and to obtain the absolute surface height fields for the first 2.5 yr of the Geosat ERM. Both the mean and the instantaneous height fields thus derived compare well with the available hydrographic data and the SST patterns from the NOAA satellites. Effects of deep mean flow and baroclinic shear are found to be important in explaining the observed propagation speeds.

Qiu, BO↗
NASA NTRS1991

Extension and strain in Northern Tharsis

The northern areas of Tharsis, south of Alba Patera, are remarkable in that they are dominated by extensive, generally north trending graben. Some graben are small isolated features whereas others are complex overlapping features in which individual fault pairs are impossible to separate. This pattern indicates an east-west extensional stress regime, consistent with stress models for Tharsis. To estimate the regional east-west extension and strain, graben along a profile at 35 N latitude, between longitudes 135 and 93 degs were studied. This profile was chosen because the graben have a northerly trend, the structures are relatively simple, the profile is anchored to ancient Noachian age crust, and high resolution images are available. The western end of the profile begins at Acheron Fossae and ends in the east at the southwestern part of Tempe Fossae. Plains units cut by the graben include Hesperian and Amazonian age members of the Alba Patera and Ceraunius Fossae Formations.

Plescia, J. B.↗
NASA NTRS1991

Extensions to the Parallel Real-Time Artificial Intelligence System (PRAIS) for fault-tolerant heterogeneous cycle-stealing reasoning

Extensions to an architecture for real-time, distributed (parallel) knowledge-based systems called the Parallel Real-time Artificial Intelligence System (PRAIS) are discussed. PRAIS strives for transparently parallelizing production (rule-based) systems, even under real-time constraints. PRAIS accomplished these goals (presented at the first annual C Language Integrated Production System (CLIPS) conference) by incorporating a dynamic task scheduler, operating system extensions for fact handling, and message-passing among multiple copies of CLIPS executing on a virtual blackboard. This distributed knowledge-based system tool uses the portability of CLIPS and common message-passing protocols to operate over a heterogeneous network of processors. Results using the original PRAIS architecture over a network of Sun 3's, Sun 4's and VAX's are presented. Mechanisms using the producer-consumer model to extend the architecture for fault-tolerance and distributed truth maintenance initiation are also discussed.

Goldstein, David↗
NASA NTRS1991

Hierarchic Extensions in the Static and Dynamic Analysis of Elastic Beams

Approximate solutions of static and dynamic beam problems by the p-version of the finite element method are investigated. Within a hierarchy of engineering beam idealizations, rigorous formulations of the strain and kinetic energies for straight and circular beam elements are presented. These formulations include rotating coordinate system effects and geometric nonlinearities to allow for the evaluation of vertical axis wind turbines, the motivating problem for this research. Hierarchic finite element spaces, based on extensions of the polynomial orders used to approximate the displacement variables, are constructed. The developed models are implemented into a general purpose computer program for evaluation. Quality control procedures are examined for a diverse set of sample problems. These procedures include estimating discretization errors in energy norm and natural frequencies, performing static and dynamic equilibrium checks, observing convergence for qualities of interest, and comparison with more exacting theories and experimental data. It is demonstrated that p-extensions produce exponential rates of convergence in the approximation of strain energy and natural frequencies for the class of problems investigated.

Watson, Robert A.↗
NASA NTRS1953

Low-speed Aileron Effectiveness as Determined by Force Tests and Visual-flow Observations on a 52 Degree Sweptback Wing with and Without Chord-extensions

The results of an investigation of the effects of leading-edge chord-extensions and extensible leading-edge flaps on the low-speed aileron characteristics of a 52 degrees sweptback wing with circular-arc airfoil sections are presented. A description and illustrations of the vortex flow as it passes over the wing are included. The investigation was conducted at Reynolds numbers of 5.5 times 10(exp 6) and 1.3 times 10(exp 6) and corresponding Mach numbers of 0.11 and 0.065 for an angle-of-attack range of 0 degrees through stall.

CONTROLS, FLAP-TYPE - COMPLETE WINGS↗
NASA NTRS1954

Investigation of the Effects of Leading-edge Chord-extensions and Fences in Combination with Leading-edge Flaps on the Aerodynamic Characteristics at Mach Numbers from 0.40 to 0.93 of a 45 Degree Sweptback Wing of Aspect Ratio 4

This investigation was made to determine the effects of 6 degree full-spoan and 3 degree partial-span leading-edge flaps in combination with chord-extensions or fences on the aerodynamic characteristics of a wing-fuselage configuration with a 45 degree sweptback wing of aspect ratio 4, taper ratio 0.3, and NACA 65A006 airfoil sections. The investigation was made in the Langley high-speed 7- by 10-foot tunnel over a Mach number range of 0.40 to 0.93 and an angle-of-attack range of about -2 degrees to 24 degrees. Lift, drag, and pitching-moment data were obtained for all configurations. From overall considerations of stability and performance it appears that with the model of this investigation the 6 degree full-span leading-edge flaps in combination with the chord-extension over the outboard 35 percent of the span, with or without leading-edge camber, would be the most desirable configuration.

Spreeman, Kenneth P↗
NASA NTRS1993

Fault geometries and extension in the Valles Marineris, Mars

The central troughs of the Valles Marineris system on Mars are generally regarded to be of tectonic origin because they are linear and bounded by faults. Their radial orientation to the Tharsis rise suggests that at least their incipient formation was influenced by the formation of the rise, but the exact role of Tharsis is not yet well understood. Collapse and erosion may have significantly modified the original tectonic troughs. To better understand the magnitude and mechanism of crustal extension across the Valles Marineris, the attitudes of trough-wall faults that parallel the long axes of the troughs were studied. Our results will help to determine if the extension is related to the Tharsis rise, to a local arch along which the troughs lie, or to other mechanisms. Fault-plane attitudes were obtained by performing a photogrammetric study of fault traces in the walls of Candor and Melas Chasmata. If the exposed wall faults are not major trough-bounding faults, it is assumed that these major faults are buried at the base of the walls and have similar geometries to the exposed faults. Three dimensional coordinates of several points along each fault trace were obtained and three-point solutions to their geometries were constructed. As expected, the results show that the faults dip toward the interior of the troughs, suggesting that they are indeed normal faults associated with trough formation.

Chadwick, D. J.↗
NASA NTRS1994

An anisotropic extension of Bodner's model of viscoplasticity: Model development

An anisotropic viscoplasticity model is developed as an extension of the well known Bodner model. The extension is made by replacing the effective stress of the isotropic Bodner model by one involving invariants for transverse isotropy. The resulting model retains the simplicity of Bodner's in the ease with which the material constants are determined experimentally. It allows a representation of strong initial anisotropy yet is based on the scalar state variable under the assertion that induced anisotropy is negligible relative to the strong initial anisotropy. Temperature dependence is taken as in the original Bodner theory. Account is made of fiber volume fraction through nonlinear rules of mixture applied to the stress history and anisotropy parameters. Focus is on the theoretical development of the model, however, application to a W/Cu composite is in progress and will be reported as a sequel to this report.

Robinson, David N.↗