Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “electrolyzer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Roll-to-roll production of catalyst coated membranes for low-temperature electrolyzers

Here we demonstrate a roll-to-roll (R2R) process for direct coating of anode catalyst layers on a polymer electrolyte membrane for low-temperature water electrolysis. To develop this process, we studied catalyst ink formulation, ink-membrane interactions, and coating quality. The catalyst inks were a mixture of iridium oxide (IrO2) and Nafion in a water and alcohol dispersion medium. The type of alcohol (methanol, ethanol, propanols) and water-to-alcohol ratio were varied to determine their influence on membrane swelling, dispersion quality, and coatability. Interactions of the ink dispersion medium with the membrane were characterized using sessile-drop contact-angle measurements. These measurements show that the ratio of water to alcohol has a strong influence on how rapidly the dispersion media is absorbed by the membrane. Rheology of the catalyst inks was measured to understand the microstructure of the catalyst particles in the ink. This analysis found that 1-propanol leads to better dispersion of the IrO2 particles than ethanol. Small-scale coating samples were prepared to understand coating uniformity and formation of irregularities. Subsequently, two water/1-propanol ratios (90:10 and 75:25) were down-selected for large-scale R2R slot die coating. The R2R catalyst-coated membrane (CCM) coating process increased catalyst layer production throughput by over 500x compared to our standard lab-scale spray coating. The CCMs obtained from this process were tested as single-cell membrane electrode assemblies. They exhibited a cell voltage of 1.91 V at a current density of 2 A/cm2, which is comparable to spray-coated CCMs. In conclusion, the work presented here demonstrates a continuous, scalable manufacturing process that eliminates the need for the decal transfer step typically used in CCM production.

42 ENGINEERING↗
DOE OSTI2026

Impact of Porous Transport Layer In-Plane Conduction on Spatially Resolved Current and EIS Measurements in a Proton Exchange Membrane Water Electrolyzer

An XY segmented cell was developed for low temperature PEM water electrolysis (PEMWE). The system can assess the local performance by enabling in situ measurements of spatial currents and impedances. In this work, we show through experiments, as well as through modelling work, that the porous transport layer (PTL) must be segmented to eliminate crosstalk. Accurate measurements are only possible when crosstalk is fully eliminated. The XY segmented cell is applied to a case study characterizing the impact of a PTL platinum coating void on spatial performance. The localized performance impact of the coating void is found to be orientation specific: coating voids facing the catalyst layer reduce performance significantly more than coating voids facing the flow field. The results suggest that the tolerances for PTL coating uniformity can be lower at the side facing the flow field. The work showcases the feasibility of the XY segmented cell for impact assessment studies. The presented XY segmented cell enables the characterization of spatial phenomena in PEMWE devices and is envisioned to support modeling efforts and the investigation of manufacturing related tolerances for mass produced PEMWE devices.

08 HYDROGEN↗
DOE OSTI2021

International Meeting on Fuel Cell and Electrolyzer Quality Control: Summary Report

Quality control (QC) for both polymer electrolyte membrane fuel cell and electrolysis membrane electrode assembly (MEA) materials is a key challenge for scale-up and cost reduction. Developing methods for detecting defects, as well as measuring critical material properties and understanding the impact of as-manufactured variations in these materials on cell performance and lifetime, are critical barriers. To help address these needs, the National Research Council Canada (NRC), Fraunhofer Institute for Solar Energy Systems (ISE), and the National Renewable Energy Laboratory (NREL) have organized and facilitated a series of workshops on the topic, bringing together industry, academia, and research institutions from North America and Europe. Prior workshops in Canada and Germany have focused on the status of quality tool capabilities and identification of needed developments for fuel cells. These meetings have garnered an excellent response and follow-on attendance, with over 100 unique attendees.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2022

Scalable High-H 2 Flux, Robust Thin Film Solid Oxide Electrolyzer

This project was aimed at the development of proton-conducting SOEC (P-SOEC) technology that has the potential to meet key DOE H 2 production targets. A decreased proton resistance of the electrolyte and Faradaic efficiency improvements were sought to increase the fraction of consumed electrolysis power that is used to actually generate H 2 , while simultaneously decreasing cost dramatically. Moreover, the development project was intended to yield maximum durability through the use of a steam protective layer. Furthermore, sputtering was used to overcome processing challenges that have hampered P-SOEC development, while the low-temperature operation goal of 500 °C was expected to aid in mitigating thermally activated long-term degradation. The approach to high-performance, lower-temperature SOECs leveraged our existing SOFC Ni-cermet anode support and extensive thin-film sputtering layer-deposition experience. Rather than an all-in-one, reversible fuel cell approach which has many unacceptable tradeoffs, we focused on the many benefits to hydrogen generating SOECs, including the existence of synergies for reduced manufacturing costs (e.g., SOECs and SOFCs share supporting layers and overall manufacturing processing). The end result of this project was expected to increase current performance at 500 °C from approximately 0.8 A/cm 2 (at 60% Faradaic efficiency) at 1.4 V to > 1 A/cm 2 (at > 95% Faradaic efficiency) with a > 40% reduction in system cost and to enable operation of P-SOECs in steam contents >> 20% for a goal of a > 40,000 hours lifetime. To enable 500 °C operation in a very high steam atmosphere (> 20%), we proposed the use of a sputtered dense thin film (~0.1-1 µm thick) of high-stability Ba(Zr,Y)O 3 (BZY) to protect the Ba(Ce,Zr,Y,Yb)O 3 (BCZYYb) electrolyte. The BZCYYb, in turn, blocks the hole conductivity of the BZY to boost Faradaic efficiency. As FE increases, more of the consumed electricity is used in electrolysis to generate H 2 , rather than being shunted. Additionally, as cell resistance decreases, the voltage required to maintain current decreases, as well as the power required to generate the same amount of H 2 . With the proposed enhancements, these two factors result in the final 46% decrease in power needed to run the system. Likewise, a production rate of 50,000 kg H 2 /day will require 55% less active area, such that a system will need only 650 cells for an 80 cm 2 active area instead of ~1,440. Taking the 2016 DOE projected current cost and modifying the electricity cost and linearly scaling the other costs (except thermal feedstock) based on the cell area improvement, results in a 44% decrease in lifetime system cost, or a decrease from $\$$4.95/kg H 2 to $\$$2.75/kg H 2 . This is well below the 2018 DOE target of $\$$4/kg H 2 . The results from this project showed that we can create a P-SOEC with enhanced steam stability using two different electrolytes (i.e., one on top of the other) and achieve sufficiently low area specific resistance (ASR) to achieve the target performance. Unfortunately, due to extended delays at the beginning of the project and related supply chain and equipment access issues, we were not able to completely show increased Faradaic efficiency for the P-SOEC and therefore were unable to demonstrate the full proof of concept within the first budget period budget. While there are still challenges that remain to be solved, significant progress was made during this project and the concept still has merit that warrants further development.

08 HYDROGEN↗
DOE OSTI2025

Performance and Durability Investigation of Thin, Low Crossover Proton Exchange Membranes for Water Electrolyzers

The goal of this project was to fabricate and study the performance and durability implications of thin, mechanically reinforced membranes containing gas recombination catalysts (GRCs) for advanced proton exchange membrane water electrolysis (PEMWE) systems. The thinner membranes, optimized for a PEMWE environment, dramatically reduced the proton transport resistance across the membrane, improving the overall efficiency of the PEMWE system. At the same time, the GRC technology was deployed to recombine crossover hydrogen from the cathode with oxygen from the anode to form water within the membrane. This reaction mitigated the buildup of hydrogen in the oxygen stream, ensuring safe operation of the PEMWE system. Capabilities to measure the gas crossover in both an ex-situ screening cell and in operando application testing were developed over the course of the project to track membrane progress and quantify deliverables. State of the art roll to roll manufacturing technologies were leveraged to fabricate the membranes on a commercial scale, where the membrane structure was precisely tuned and GRC distributed within the membrane structure.

08 HYDROGEN↗