Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “effect measure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

Highlights of unsteady pressure tests on a 14 percent supercritical airfoil at high Reynolds number, transonic condition

Steady and unsteady pressures were measured on a 2-D supercritical airfoil in the Langley Research Center 0.3-m Transonic Cryogenic Tunnel at Reynolds numbers from 6 x 1,000,000 to 35 x 1,000,000. The airfoil was oscillated in pitch at amplitudes from plus or minus .25 degrees to plus or minus 1.0 degrees at frequencies from 5 Hz to 60 Hz. The special requirements of testing an unsteady pressure model in a pressurized cryogenic tunnel are discussed. Selected steady measured data are presented and are compared with GRUMFOIL calculations at Reynolds number of 6 x 1,000,000 and 30 x 1,000,000. Experimental unsteady results at Reynolds numbers of 6 x 1,000,000 and 30 x 1,000,000 are examined for Reynolds number effects. Measured unsteady results at two mean angles of attack at a Reynolds number of 30 x 1,000,000 are also examined.

Hess, Robert W.↗

Lack of effects of astemizole on vestibular ocular reflex, motion sickness, and cognitive performance in man

Astemizole was orally administered to 20 subjects in a randomized, double-blind design to assess the efficacy of this peripherally active antihistamine as an antimotion sickness drug possessing no central side-effects. Measures of vestibular ocular reflex (VOR) were made to evaluate the agent as a selective vestibular depressant. Following one week of orally administered astemizole (30 mg daily), a Staircase Profile Test, a VOR test, and a variety of tests of cognitive performance were administered. These tests revealed no statistically significant effects of astemizole. This leads to the conclusion that, although the drug probably reaches the peripheral vestibular apparatus in man by crossing the blood-vestibular barrier, a selective peripheral antihistamine (H1) action is inadequate to control motion sickness induced through cross-coupled accelerative semicircular canal stimulation in a rotating chair.

Kohl, Randall L.↗

Effect of Air Cooling of Turbine Disk on Power and Efficiency of Turbine from Turbo Engineering Corporation TT13-18 Turbosupercharger.

An investigation was conducted to determine the effect of turbine-disk cooling with air on the efficiency and the power output of the radial-flow turbine from the Turbo Engineering Corporation TT13-18 turbosupercharger. The turbine was operated at a constant range of ratios of turbine-inlet total pressure to turbine-outlet static pressure of 1,5 and 2.0, turbine-inlet total pressure of 30 inches mercury absolute, turbine-inlet total temperature of 12000 to 20000 R, and rotor speeds of 6000 to 22,000 rpm, Over the normal operating range of the turbine, varying the corrected cooling-air weight flow from approximately 0,30 to 0.75 pound per second produced no measurable effect on the corrected turbine shaft horsepower or the turbine shaft adiabatic efficiency. Varying the turbine-inlet total temperature from 12000 to 20000 R caused no measurable change in the corrected cooling-air weight flow. Calculations indicated that the cooling-air pumping power in the disk passages was small and was within the limits of the accuracy of the power measurements. For high turbine power output, the power loss to the compressor for compressing the cooling air was approximately 3 percent of the total turbine shaft horsepower.

Berkey, William E.↗

Sunyaev-Zeldovich Effect Studies of Galaxy Clusters with Bolocam (and Future Instrumentation)

Galaxy clusters are excellent laboratories for studying the astrophysics of gravitational collapse and the non-self-similar processes that can affect it. A number of different techniques allow us to study the distribution of the consituents of galaxy clusters. The thermal Sunyaev-Zeldovich effect measures the line-of-sight integral of the the pressure in the ICM plasma. Comparison to and combination with other probes enables a variety of studies of the ICM and of clusters: scaling relations, radial profiles, tests of hydrostatic equilibrium, etc. We report on the status of our program to image clusters in the thermal Sunyaev-Zeldovich effect at 150GHz using Bolocam and perform such tests. We also describe the upcoming MKIDCam long-wavelength multi-color facility camera for the CSO, which will provide new capabilities in thermal Sunyaev-Zeldovich effect imaging. We comment on the role Tom Phillips and the CSO have played in facilitating the development of mm-wave SZ observations.

Golwala, Sunil↗

Determination of the Accommodation Coefficient Using Vapor/gas Bubble Dynamics in an Acoustic Field

Nonequilibrium liquid/vapor phase transformations can occur in superheated or subcooled liquids in fast processes such as in evaporation in a vacuum. The rate at which such a phase transformation occurs depends on the "condensation" or "accommodation" coefficient, Beta, which is a property of the interface. Existing measurement techniques for Beta are complex and expensive. The development of a relatively inexpensive and reliable technique for measurement of Beta for a wide range of substances and temperatures is of great practical importance. The dynamics of a bubble in an acoustic field strongly depends on the value of Beta. It is known that near the saturation temperature, small vapor bubbles grow under the action of an acoustic field due to "rectified heat transfer." This finding can be used as the basis for an effective measurement technique of Beta. We developed a theory of vapor bubble behavior in an isotropic acoustic wave and in a plane standing acoustic wave. A numerical code was developed which enables simulation of a variety of experimental situations and accurately takes into account slowly evolving temperature. A parametric study showed that the measurement of Beta can be made over a broad range of frequencies and bubble sizes. We found several interesting regimes and conditions which can be efficiently used for measurements of Beta. Measurements of Beta can be performed in both reduced and normal gravity environments.

Gumerov, Nail A.↗

Absorbed dose thresholds and absorbed dose rate limitations for studies of electron radiation effects on polyetherimides

The threshold values of total absorbed dose for causing changes in tensile properties of a polyetherimide film and the limitations of the absorbed dose rate for accelerated-exposure evaluation of the effects of electron radiation in geosynchronous orbit were studied. Total absorbed doses from 1 kGy to 100 MGy and absorbed dose rates from 0.01 MGy/hr to 100 MGy/hr were investigated, where 1 Gy equals 100 rads. Total doses less than 2.5 MGy did not significantly change the tensile properties of the film whereas doses higher than 2.5 MGy significantly reduced elongation-to-failure. There was no measurable effect of the dose rate on the tensile properties for accelerated electron exposures.

Long, Edward R., Jr.↗

Enabling Innovative Research on the International Space Station to Solve the Challenges of A Human Mission to Mars: Results of the ISS4Mars International Workshops 2020–2021

During the ISS4Mars workshops in 2020–2021, personnel from the International Space Station (ISS) partner agencies convened to reflect on scenarios for how the ISS could be used and its operations possibly modified to simulate aspects of a human mission to Mars. Scientific leaders, operations experts, crewmembers, managers, and flight surgeons discussed the five hazards of human spaceflight—gravity transitions, radiation, isolation and confinement, distance from Earth, and hostile closed environments—and considered how an ISS-based analog of Mars transit could benefit assessments and mitigations of these hazards. A focused writing team then discussed the advantages and disadvantages of each approach identified by the workshop participants before developing a set of eight use cases to consider the feasibility of implementing on the ISS. The writing team also identified the prerequisites needed, including ground analog studies simulating a mission to Mars required to verify measurements and procedures, before testing could begin on the ISS. Five of the use cases were considered feasible to assess in simulations using an ISS-based analog of Mars transit if some ground rules and assumptions were met. These five use cases were Earth-independent medical operations, Earth-independent integrated operations, life support and food for a one year duration, lower-body negative pressure as a countermeasure against the effects of exposure to microgravity, and fitness levels after landing. In addition, three more extensive interventions—extended Mars surface operations, a small-volume transit analog, and artificial gravity—were deemed unfeasible for testing on the ISS. Experience gained from the five use cases executed on the ISS may help answer some of the questions in the deferred scenarios, or it may be possible to complete them on another platform (e.g. commercial space station, lunar habitat). Simulating conditions during a Mars mission on the ISS will afford higher fidelity for assessing multiple integrated hazards of human spaceflight, however, ground analogs of Mars missions can be used to ensure effective measures and experimental design before testing begins on the ISS. The strategic concepts refined as part of these workshops were brought to a multilateral forum, Mulitlateral Human Research Planel for Exploration (MHRPE), where ISS partner agencies are now discussing implementation plans to provide new opportunities to use the ISS to prepare for deep space exploration over the coming decade. In this publication we present a summary of the international strategic plans for future research that will enable operations, software, and countermeasures to be developed that will reduce the risk to humans during future crewed missions to Mars.

Human space exploration↗

Experimental investigation of contamination prevention techniques to cryogenic surfaces on board orbiting spacecraft

Within the simulation limitations of on-orbit conditions, it was demonstrated that a helium purge system could be an effective method for reducing the incoming flux of contaminant species. Although a generalized purge system was employed in conjunction with basic telescope components, the simulation provided data that could be used for further modeling and design of a specific helium injection system. Experimental telescope pressures required for 90% attenuation appeared to be slightly higher (factor of 2 to 5). Cooling the helium purge gas and telescope components from 300 to 140 K had no measurable effect on stopping efficiency of a given mass flow of helium from the diffuse injector.

Hetrick, M. A.↗

An experimental examination of the effects of incoming boundary layer modifications on the dynamics of a turbulent compression corner interaction

This experimental study examines the effects of modifications to the incoming turbulent boundary layer on the highly separated shock wave/boundary layer interaction generated by an unswept compression corner. Particular focus is placed on the motion of the unsteady separation shock wave. The flowfield was generated by a 28 deg ramp in a Mach 5 flow with a freestream Reynolds number of 50 x 10 exp 6/m. The incoming turbulent boundary layer transitioned naturally and developed under near-adiabatic wall conditions. Modification of the flow entering the interaction was effected through either a single plate boundary layer manipulator (BLM) or riblets. The BLM reduced the length of separation by 35-45 percent and reduced the streamwise extent of the separation shock motion by 36-74 percent. Examination of the flowfield downstream of the BLM showed this result to be due to the inviscid preturning of the flow by the BLM, and not by changes to the boundary layer dynamics. The riblets had no measurable effect on the compression corner interaction.

Mcclure, W. B.↗

Turbulent spectra, fluxes, stability and growth of the mixed layer in the boundary layer of Mars

Spectra of wind and temperature from high frequency measurements in the atmospheric surface layer of Mars are presented for the first time. Heat and momentum fluxes, and stability are calculated for early spring from estimates of the surface temperature and mean Viking Lander 2 temperature and wind at 44 degrees N, using similarity theory. This study provides the first estimates of (1) the height of the mixed layer, (2) spectra of wind and temperature, (3) the validity of similarity theories on Mars, and (4) bounds of effective measuring height and surface roughness. It confirms and extends the universiality of model wind spectra. Finally and more important, we provide the ability to estimate and determine the self-consistency of Martian atmospheric mixed layer fluxes, stability and heights on a diurnal and annual basis. This can be used to initialize and validate the various models, which previously could only be compared with each other or the efforts of Sutton, Leovy and Tillman: these were restricted in season and limited by the results from the surface temperature model available at that time. Analysis of additional data can better estimate z(sub 0) values directly from the measurements and provide the parameters necessary to calculate the vertical profiles of wind and temperature on a daily, seasonal and annual basis.

Tillman, James E.↗

Heat Transfer In High-Temperature Multilayer Insulation

The combined radiation/conduction heat transfer in high-temperature multilayer insulations for typical reentry of reusable launch vehicles from low Earth orbit was investigated experimentally and numerically. The high-temperature multilayer insulation investigated consisted of gold-coated reflective foils separated by alumina fibrous insulation spacers. The steady-state heat transfer through four multilayer insulation configurations was investigated experimentally over the temperature range of 300-1300 K and environmental pressure range of 1.33 10(exp -5)-101.32 kPa. It was shown that including the reflective foils reduced the effective thermal conductivity compared to fibrous insulation sample at 1.5 times the density of the multilayer sample. A finite volume numerical model was developed to solve the governing combined radiation/conduction heat transfer equations. The radiation heat transfer in the fibrous insulation spacers was modeled using the modified two-flux approximation assuming anisotropic scattering and gray medium. The numerical model was validated by comparison with steady-state experimental data. The root mean square deviation between the predicted and measured effective thermal conductivity of the samples was 9.5%.

Daryabeigi, Kamran↗

Numerical Analysis of Temperature Gradients and Interface Shape During Directional Solidification of Al and Al-Cu Alloy Under Microgravity Conditions

Numerical modeling was undertaken to analyze the influence of radial thermal gradient on solid/liquid interface shape and convection patterns during solidification of pure Al and Al-4 wt. % Cu alloy. Steady state calculations were performed for different gravity levels and orientations. Furthermore, transient modeling was undertaken to investigate effect of the solidification velocity. The furnace configuration used in this analysis is the proposed International Space Station Furnace. Results from a thermal model of the furnace core were used as initial boundary conditions for solidification modeling. The Solidification model was adopted from previous work and was based on the finite element code FIDAP. Thermocouple data and quenched interface shape from a pure Al sample flown on the Life Sciences and Microgravity Spacelab (LMS) mission, July 1996 was used for model validation. Good agreement was obtained between the predicted interface shape and that measured from the quenched LMS sample. It was found that the imposed temperature boundary condition must be sufficiently smooth for the heat fluxes in the model to be self-consistent. The model predicted that alloy sample Al-Cu is more sensitive to variations in the gravity level compared to pure Al. For Al-Cu alloy, solute diffusivity is approximately 10(exp 4) times smaller than thermal diffusivity of pure Al. Hence, in a microgravity environment the weak convection has no measurable effect on the heat fluxes, but is still strong enough to affect concentration distribution. Since the alloy melting temperature is determined by concentration the interface shape depends on the level of convection. This was found not to be the case for pure metal.

Bune, Andris V.↗

Gravitational Redshift in a Local Freely Falling Frame: A Proposed New Null Test of the Equivalence Principle

We consider the gravitational redshift effect measured by an observer in a local freely failing frame (LFFF) in the gravitational field of a massive body. For purely metric theories of gravity, the metric in a LFFF is expected to differ from that of flat spacetime by only "tidal" terms of order (GM/c(exp 2)R)(r'/R )(exp 2), where R is the distance of the observer from the massive body, and r' is the coordinate separation relative to the origin of the LFFF. A simple derivation shows that a violation of the equivalence principle for certain types of "clocks" could lead to a larger apparent redshift effect of order (1 - alpha)(G M/c(exp 2)R)(r'/R), where alpha parametrizes the violation (alpha = 1 for purely metric theories, such as general relativity). Therefore, redshift experiments in a LFFF with separated clocks can provide a new null test of the equivalence principle. With presently available technology, it is possible to reach an accuracy of 0.01% in the gravitational field of the Sun using an atomic clock orbiting the Earth. A 1% test in the gravitational field of the galaxy would be possible if an atomic frequency standard were flown on a space mission to the outer solar system.

Krisher, Timothy P.↗

Tunable Far Infrared Studies in Support of Stratospheric Measurements

This report summarizes research done under NASA Grant NAG5-4653. The research performed under this grant has been a collaboration between institutions including the Smithsonian Astrophysical Observatory, the National Institute of Standards and Technology, the University of Oregon, and the NASA Langley Research Center. The program has included fully line-resolved measurements of submillimeter and far infrared spectroscopic line parameters (pressure broadening coefficients and their temperature dependences, and line positions) for the analysis of field measurements of stratospheric constituents, far infrared database improvements, and studies for improved satellite measurements of the Earth's atmosphere. This research program is designed to enable the full utilization of spectra obtained in far infrared/submillimeter field measurements, such as FIRS-2, FILOS, IBEX, SLS, EosMLS, and proposed European Space Agency measurements of OH (e.g., PIRAMHYD and SFINX) for the retrieval of accurate stratospheric altitude profiles of key trace gases involved in ozone layer photochemistry. For the analysis of the spectra obtained in the stratosphere from far infrared measurements it is necessary to have accurate values of the molecular parameters (line positions, strengths, and pressure broadening coefficients) for the measured molecules and for possible interfering species. Knowledge of line positions is in increasingly good shape, with some notable exceptions. The increase in position information includes research that has been performed in the present program of research on HO2, H2O, H2O2, O3, HCl, HF, HBr, HI, CO, OH, and ClO. Examples where further line position studies are necessary include hot band and minor isotopomer lines of some of the major trace species (H2O, O3) and normal lines of some triatomic and larger molecules (NO2). Knowledge of strengths is in generally good shape, since most of the lines are from electric dipole transitions whose intensities are well determined from Stark effect measurements; exceptions include some molecules with large vibration-rotation interactions (NO2) and internal motions (H2O2 above the lowest torsional state). The line parameters that are still the least well determined are pressure broadening coefficients, and their temperature coefficients, These are strongly dependent on the quantum states involved in the transitions, in a way that is much more complex than the simple projection by directional cosine matrix elements involved in determination of rotational line strengths from static dipole moments. The following molecules have now been measured or detected in the atmosphere using far infrared and millimeter-wave emission spectroscopy from balloon- and satellite-borne spectrometers: OH, HO2, H2O (including minor isotopomers and hot band lines), H2O2, O3P, O2 (including minor isotopomers), O3 (including minor isotopomers and hot band lines), HOCl, HCl, HF, HBr, CIO, CO, CO2, N2O, NO2, N2O5, HNO3, ClNO3, and HCN. Many of these species have spectral lines that are saturated in stratospheric spectra. In these cases, the measured line equivalent widths are proportional to (line strength x Lorentz width) (exp 1/2) so that the pressure broadening coefficients are as important as the line intensities in determining concentration profiles. Interpretation of field measurements for these species have required ongoing measurement programs of pressure broadening measurements. Other species (HO2, HGCl, H2O2, HBr, and NO2, as examples) have required further line position studies in order to fully analyze the field measurements.

Chance, Kelly V.↗

Fundamental Properties of O-Type Stars

We present a comprehensive analysis of high-resolution, far-ultraviolet HST STIS, FUSE, and optical spectra of 18 O stars in the Small Magellanic Cloud. Our analysis is based on the OSTAR2002 grid of NLTE metal-line-blanketed model atmospheres calculated with our code TLUSTY. We systematically explore and present the sensitivity of various UV and optical lines to different stellar parameters. We have obtained consistent fits of the UV and the optical spectrum to derive the effective temperature, surface gravity, surface composition, and microturbulent velocity of each star. Stellar radii, masses, and luminosities follow directly. For stars of the same spectral subtype, we find a general good agreement between effective temperature determinations obtained with TLUSTY, CMFGEN, and FASTWIND models, which are all lower than the standard T(sub eff) calibration of O stars. We propose a new calibration between the spectral type and effective temperature based on our results from UV metal lines, as well as optical hydrogen and helium lines. The lower effective temperatures translate into ionizing luminosities that are smaller by a factor of 3 compared to luminosities inferred from previous standard calibrations. The chemical composition analysis reveals that the surface of about 80% of the program stars is moderately to strongly enriched in nitrogen, while showing the original helium, carbon, and oxygen abundances. Our results support the new stellar evolution models that predict that the surface of fast rotating stars becomes nitrogen-rich during the main-sequence phase because of rotationally induced mixing. Enrichment factors are, however, larger than predicted by stellar evolution models. Most stars exhibit the "mass discrepancy" problem, which we interpret as a result of fast rotation that lowers the measured effective gravity. Nitrogen enrichment and low spectroscopic masses are therefore two manifestations of fast rotation. Our study thus emphasizes the importance of rotation in our understanding of the properties of massive stars and provides a framework for investigating populations of low-metallicity massive stars at low and high redshifts.

Heap, Sara R.↗

Effect of Rare Earth Elements (Er, Ho) on Semi-Metallic Materials (ScN) in an Applied Electric Field

The development of materials and fabrication technology for field-controlled spectrally active optics is essential for applications such as membrane optics, filters for LIDARs, windows for sensors, telescopes, spectroscopes, cameras and flat-panel displays. The dopants of rare earth elements, in a host of optical systems, create a number of absorption and emission band structures and can easily be incorporated into many high quality crystalline and amorphous hosts. In wide band-gap semiconductors like ScN, the existing deep levels can capture or emit the mobile charges, and can be ionized with the loss or capture of the carriers which are the fundamental basis of concept for smart optic materials. The band gap shrinkage or splitting with dopants supports the possibility of this concept. In the present work, a semi-metallic material (ScN) was doped with rare earth elements (Er, Ho) and tested under an applied electric field to characterize spectral and refractive index shifts by either Stark or Zeeman Effect. These effects can be verified using the UV-Vis spectroscopy, the Hall Effect measurement and the ellipsometric spectroscopy. The optical band gaps of ScN doped with Er and doped with Ho were experimentally estimated as 2.33eV and 2.24eV ( 0.2eV) respectively. This is less than that of undoped ScN (2.5 0.2eV). The red-shifted absorption onset is a direct evidence for the decrease of band gap energy (Eg), and the broadening of valence band states is attributable to the doping cases. A decrease in refractive index with an applied field was observed as a small shift in absorption coefficient using a variable angle spectroscopic ellipsometer. In the presence of an electric field, mobile carriers are redistributed within the space charge region (SCR) to produce this electro-refractive effect. The shift in refractive index is also affected by the density and location of deep potential wells within the SCR. In addition, the microstructure change was observed by a TEM analysis. These results give an insight for future applications for the field-controlled spectrally active material systems.

Kim, Hyunjung↗