Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “edge”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS2015

Characterization of Flap Edge Noise Radiation from a High-Fidelity Airframe Model

The results of an experimental study of the noise generated by a baseline high-fidelity airframe model are presented. The test campaign was conducted in the open-jet test section of the NASA Langley 14- by 22-foot Subsonic Tunnel on an 18%-scale, semi-span Gulfstream airframe model incorporating a trailing edge flap and main landing gear. Unsteady surface pressure measurements were obtained from a series of sensors positioned along the two flap edges, and far field acoustic measurements were obtained using a 97-microphone phased array that viewed the pressure side of the airframe. The DAMAS array deconvolution method was employed to determine the locations and strengths of relevant noise sources in the vicinity of the flap edges and the landing gear. A Coherent Output Power (COP) spectral method was used to couple the unsteady surface pressures measured along the flap edges with the phased array output. The results indicate that outboard flap edge noise is dominated by the flap bulb seal cavity with very strong COP coherence over an approximate model-scale frequency range of 1 to 5 kHz observed between the array output and those unsteady pressure sensors nearest the aft end of the cavity. An examination of experimental COP spectra for the inboard flap proved inconclusive, most likely due to a combination of coherence loss caused by decorrelation of acoustic waves propagating through the thick wind tunnel shear layer and contamination of the spectra by tunnel background noise at lower frequencies. Directivity measurements obtained from integration of DAMAS pressure-squared values over defined geometric zones around the model show that the baseline flap and landing gear are only moderately directional as a function of polar emission angle.

Humphreys, William M., Jr.↗
NASA NTRS2010

Use of a Hybrid Edge Node-Centroid Node Approach to Thermal Modeling

A recent proposal submitted for an ESA mission required that models be delivered in ESARAD/ESAT AN formats. ThermalDesktop was the preferable analysis code to be used for model development with a conversion done as the final step before delivery. However, due to some differences between the capabilities of the two codes, a unique approach was developed to take advantage of the edge node capability of ThermalDesktop while maintaining the centroid node approach used by ESARAD. In essence, two separate meshes were used: one for conduction and one for radiation. The conduction calculations were eliminated from the radiation surfaces and the capacitance and radiative calculations were eliminated from the conduction surfaces. The resulting conduction surface nodes were coincident with all nodes of the radiation surface and were subsequently merged, while the nodes along the edges remained free. Merging of nodes on the edges of adjacent surfaces provided the conductive links between surfaces. Lastly, all nodes along edges were placed into the subnetwork and the resulting supernetwork included only the nodes associated with radiation surfaces. This approach had both benefits and disadvantages. The use of centroid, surface based radiation reduces the overall size of the radiation network, which is often the most computationally intensive part of the modeling process. Furthermore, using the conduction surfaces and allowing ThermalDesktop to calculate the conduction network can save significant time by not having to manually generate the couplings. Lastly, the resulting GMM/TMM models can be exported to formats which do not support edge nodes. One drawback, however, is the necessity to maintain two sets of surfaces. This requires additional care on the part of the analyst to ensure communication between the conductive and radiative surfaces in the resulting overall network. However, with more frequent use of this technique, the benefits of this approach can far outweigh the additional effort.

Peabody, Hume L.↗
NASA NTRS2018

Development of Low-Scatter Optical Edges for Starshades

Starshades, combined with future space telescopes, provide the ability to detect Earth-like exoplanets in the habitable zone by producing high contrast ratios at small inner working angles. The primary function of a starshade is to suppress light from a target star such that its orbiting planets are revealed. In order to do so, the optical edges of the starshade must maintain their precise in-plane profile to produce the necessary apodization function. However, an equally important consideration is the interaction of these edges with light emanating from our own Sun as scattered and/or diffracted sunlight can significantly degrade the achievable contrast. This paper describes the technical efforts performed to obtain precision, low-scatter optical edges for future starshades. Trades between edge radius (i.e. sharpness) and surface reflectivity have been made and small-scale coupons have been produced using scalable manufacturing processes. A custom scattered light testbed has been developed to quantify the magnitude of scattered light over all sun angles. Models have also been developed to make predictions on the level of reflected and/or diffracted light for various edge architectures. The results of these studies have established a current baseline approach which implements photochemical etching techniques on thin metal foils.

Bradley, Christine↗
NASA NTRSDate not supplied

Zero-Trust Architecture for Autonomous Edge Computing

We are at the apex of an aviation revolution where autonomy will play a central role in enabling complex, multi-agent systems to communicate, interact, and collaborate on a myriad of applications spanning autonomous swarms to wild-fire management. Autonomy is not an absolute but rather a spectrum ranging from a system requiring significant human intervention to one requiring little to none [1]. For example, the extreme, in the case of an autonomous aircraft, is one that operates independently in the airspace interacting with all other elements (air traffic controllers, other pilots) as if it were a human pilot. Critical to this vision is an architecture that enables autonomous agents to interact with minimal latency. Edge computing is an emerging architecture where compute and storage is pushed to the ‘edge’ of the network in order to minimize the round-trip time from agent to resource thereby mitigating the latency associated with cloud-only based approaches. Additionally, services can generate massive amounts of data (e.g., video feeds), which may require analysis in near real-time. Moving this data to the cloud for further processing may not be feasible due to latency, bandwidth, and cost. Privacy, security, and reliability can also be improved by edge computing architectures. However, this geo-distributed and dynamic* architecture complicates the establishment of unambiguous network security boundaries and can lead to vulnerabilities including man in the middle attacks, replay attacks, physical security breaches of edge nodes, signal interception, etc. This motivates the need for zero-trust architectures [2–4] which de-emphasize the notion of static network perimeters and, as the name implies, do not instill any innate trust in any particular agent. It is required that all agents must be authorized and approved in every transaction. In this paper, we present a zero-trust architecture suitable for edge-computing applications that demand significant low-latency, security, privacy, and reliability.

zero trust↗
NASA NTRSDate not supplied

Diffraction by Sharp Edges of Noncanonical Shape with Mean Flow and Surface Impedance

This paper presents a study on diffraction by sharp edges of noncanonical edge shape in the presence of mean flow and surface impedance, which are important features for aircraft noise but have not been accounted for in previous studies on sharp-edge diffraction. An analytical formula for the diffracted pressure is derived by applying asymptotic analysis to the integral representation of the total pressure scattered by a geometry that contains sharp edges. The asymptotic analysis is presented as a systematic process that can be carried out to any order, if needed. An illustration is given to use a higher-order result to eliminate the singularity in the first-order result to make the solution regular in the entire parameter domain. The formula for the diffracted pressure is validated by experimental data and is applied to parametric studies to reveal the effects of noncanonical edge shape, mean flow and surface impedance, as well as the impact of these effects on the total scattered pressure in the presence of other scattering components.

Yueping Guo↗
NASA NTRSDate not supplied

Edge Based Viscous Method for Node-Centered Formulations

This paper presents a novel, efficient, conservative, edge-based method for evaluation of mean flow viscous fluxes and turbulence-model diffusion terms of the Reynolds-averaged Navier-Stokes equations on tetrahedral grids. The new method is implemented in a practical, node-centered, finite-volume computational fluid dynamics solver. The baseline finite-volume scheme that is equivalent to a second-order accurate finite-element Galerkin approximation of viscous stresses is reformulated. The order of operations to compute the cell-based Green-Gauss gradients is changed to combine the operations by edge, which leads to an equivalent formulation on tetrahedral grids, improves efficiency, and preserves the compact discretization stencil based on the nearest neighbors. The computational results presented in this paper verify the implementation of this edge-based method by comparing its accuracy and iterative convergence with those of the well verified and validated baseline formulation. Efficiency gains for residual and Jacobian evaluations result in significant reduction of time to solution. This novel edge-based formulation on tetrahedra can be seamlessly combined with the baseline formulation on cells of other types for computing solutions on mixed-element grids.

Edge Based↗
NASA NTRSDate not supplied

Dynamic Analysis of Reynolds Number Effects on Trailing Edge Transonic Vortex Shedding and Its Impact on Turbine Blade Aerodynamic Performance

In this work, we will discuss observations from images acquired from a time-resolved, high-speed self-aligned focusing Schlieren campaign that was performed at the CW-22 facility at NASA Glenn Research Center to understand the dynamic behavior of thick trailing-edge high-pressure turbine blades simulating a ceramic matrix composite (CMC) construction at high inlet turbulence conditions. For the CMC-9 blade, which has a trailing edge thickness of 9% of the axial chord, we identified a regime where an excessive total pressure loss (loss anomaly) is observed only for a narrow range of Reynolds numbers at a fixed exit Mach number of 0.74. The loss anomaly is qualitatively explained by our images, which were taken at 10 distinct blade Reynolds numbers spanning a factor of 6. The images show a significant increase in energy related to the oscillations due to transonic vortex shedding at the Reynolds numbers related to the high loss conditions. This increased energy leads to the formation of strong acoustic waves that turn into shock waves at the highest loss conditions. From our observations stemming from Spectral POD analysis of the high-speed images, we see the acoustic waves produced by the trailing edge vortex shedding exist in all conditions tested; but the shedding frequency has a very slight trend upwards as the Reynolds number is increased, varying about 6% in the range tested. Considering this variation of shedding frequency as a function of Reynolds number, which is well-established for other bluff-body flows, we stipulate there may be a potential feedback mechanism involving an acoustic information transfer path across neighboring blades that may explain why only a narrow range of Reynolds numbers displays strong, shock-forming vortex shedding. We consider a few feedback paths and examine the timing based on the mean flow field from a high-resolution LES simulation. It appears that all feedback mechanisms are viable, presenting an integer number of delay cycles with respect to disturbances generated at the trailing edge. Most noteworthy, however, is the acoustic/shock-boundary layer interaction mechanism at the blade geometric throat. Based on our analysis, this mechanism likely plays an important role in realistic, curved turbine blade passages.

Aerodynamics↗
NASA NTRS1972

Effects of increased leading-edge thickness on performance of a transonic rotor blade

A single-stage transonic compressor was tested with two rotor blade leading-edge configurations to investigate the effect of increased leading-edge thickness on the performance of a transonic blade row. The original rotor blade configuration was modified by cutting back the leading edge sufficiently to double the blade leading-edge thickness and thus the blade gap blockage in the tip region. At design speed this modification resulted in a decrease in rotor overall peak efficiency of four points. The major portion of this decrement in rotor overall peak efficienty was attributed to the flow conditions in the outer 30 percent of the blade span. At 70 and 90 percent of design speed, the modification had very little effect on rotor overall performance.

Reid, L.↗
NASA NTRS1974

Cold-air study of the effect on turbine stator blade aerodynamic performance of coolant ejection from various trailing-edge slot geometries. 1: Experimental results

Trailing-edge slot configurations were investigated in a two-dimensional cascade of turbine stator blades. The trailing-edge slots were incorporated into blades with round trailing edges. The five blade configurations investigated included blades with two different trailing-edge thicknesses and four different slot widths. The results of the investigation showed that there was, in general, a significant increase in primary-air efficiency due to the coolant flow, the increase varying with slot configuration. For the five configurations tested, the average percent change in primary-air efficiency per percent coolant flow varied almost linearly from zero to about 1.4 percent over a range of coolant- to primary-air exit-velocity ratios between 0 and 1.2. However, for different configurations there was considerable deviation from the average values in the lower range of exit velocity ratios.

Prust, H. W., Jr.↗
NASA NTRS1974

Effect of trailing-edge flap deflection on the lateral and longitudinal-stability characteristics of a supersonic transport model having a highly-swept arrow wing

A low-speed investigation has been made on a highly-swept wing model having a thickened leading edge to determine the effect of inboard trailing-edge flaps on the characteristics of the model in pitch and sideslip. The tests were made at a Mach number of 0.227 which corresponds to a Reynolds number of about 5.53 million based on the reference chord. The results showed that deflection of the trailing-edge flaps decreased the roll due to sideslip by about 20 percent at a landing lift coefficient of 0.5. The directional-stability parameter, was increased by deflection of the flaps and the range of lift coefficients over which it was positive was also increased. The longitudinal stability characteristics of the model without leading-edge devices were improved by increased flap deflection, that is, the pitch-up tendency was delayed to higher lift coefficients. The lift coefficient increment resulting from the 15 deg flap deflection compared favorably with that predicted.

Lockwood, V. E.↗
NASA NTRS1974

Effect of spanwise blowing on leading-edge vortex bursting of a highly swept aspect ratio 1.18 delta wing

An investigation was conducted in the Langley 1/8-scale V/STOL model tunnel on a semispan delta wing with a leading-edge sweep of 74 deg, to determine the effectiveness of various locations of upper surface and reflection plane blowing on leading-edge vortex bursting. Constant area nozzles were located on the wing upper surface along a ray swept 79 deg, which was beneath the leading-edge vortex core. The bursting and reformation of the leading-edge vortex was viewed by injecting helium into the vortex core, and employing a schlieren system.

Scantling, W. L.↗
NASA NTRS1973

Design fabrication, testing, and delivery of shuttle heat pipe leading edge test modules. Volume 1: Executive summary

The construction of two test modules is presented for a feasibility demonstration of a concept for reusable space shuttle wing leading edge surfaces. In this leading edge concept high temperature heat pipes were incorporated into the structure to cool the stagnation region, allowing the use of super-alloys in place of refractory metal, ablator protected, or carbon-carbon structures. The program included the analysis and design of the heat pipes, their integration into the test module structure, heat pipe development testing, construction of the test modules and a facility adapter, and formulation of recommended testing conditions. The results of the heat pipe and leading edge module thermal analyses indicate the test modules will meet the design goal; reducing the leading edge temperature at the stagnation line from 1315 C (2400 F) to less than 1010 C (1850 F). The development tests demonstrated that the module assembly could be brazed with active heat pipes, as was borne out by the subsequent successful brazing of both modules with active heat pipes loaded with sodium.

Source record↗
NASA NTRS1975

Cold air study of the effect on turbine stator blade aerodynamic performance of coolant ejection from various trailing edge slot geometries. 2: Comparison of experimental and analytical results

Experimentally determined efficiencies of turbine stator blades having trailing-edge coolant ejection are compared with efficiencies predicted from two previously published approximate analytical methods. The experimental results were obtained from two-dimensional data with the temperature of the primary and coolant flows both being nearly ambient. Data from five stator blade configurations having different slotted trailing-edge geometries were included in the comparison. The two analytical methods gave results which agreed reasonably well with experimental results. An average of the absolute values of differences between experimental and predicted efficiencies for all five blade configurations showed that one method gave average efficiency differences which were about 1.3 percent different than experimental efficiencies, while the other method gave average efficiency differences that were about 0.7 percent different than experimental. However, in some instances, maximum differences of as much as 4 percent occurred. A comparison between experimental and analytical results indicated that the ratio of trailing-edge slot width to trailing-edge thickness influences the measured efficiencies to a greater extent than is accounted for by either analytical model.

Prust, H. W., Jr.↗
NASA NTRS1974

Effect of canard position and wing leading-edge flap deflection on wing buffet at transonic speeds

A generalized wind-tunnel model, with canard and wing planform typical of highly maneuverable aircraft, was tested. The addition of a canard above the wing chord plane, for the configuration with leading-edge flaps undeflected, produced substantially higher total configuration lift coefficients before buffet onset than the configuration with the canard off and leading-edge flaps undeflected. The wing buffet intensity was substantially lower for the canard-wing configuration than the wing-alone configuration. The low-canard configuration generally displayed the poorest buffet characteristics. Deflecting the wing leading-edge flaps substantially improved the wing buffet characteristics for canard-off configurations. The addition of the high canard did not appear to substantially improve the wing buffet characteristics of the wing with leading-edge flaps deflected.

Gloss, B. B.↗
NASA NTRS1975

Subscale, hydrogen-burning, airframe-integrated-scramjet: Experimental and theoretical evaluation of a water cooled strut airframe-integrated-scramjet: Experimental leading edge

A water-cooled leading-edge design for an engine/airframe integrated scramjet model strut leading edge was evaluated. The cooling design employs a copper cooling tube brazed just downstream of the leading edge of a wedge-shaped strut which is constructed of oxygen-free copper. The survival of the strut leading edge during a series of tests at stagnation point heating rates confirms the practicality of the cooling design. A finite difference thermal model of the strut was also proven valid by the reasonable agreement of calculated and measured values of surface temperature and cooling-water heat transfer.

Pinckney, S. Z.↗
NASA NTRS1975

A leading edge heating array and a flat surface heating array: Final design

A heating array is described for testing full-scale sections of the leading edge and lower fuselage surfaces of the shuttle. The heating array was designed to provide a tool for development and acceptance testing of leading edge segments and large flat sections of the main body thermal protection system. The array was designed using a variable length module concept to meet test requirements using interchangeable components from one test configuration in another configuration. Heat generating modules and heat absorbing modules were employed to achieve the thermal gradient around the leading edge. A support was developed to hold the modules to form an envelope around a variety of leading edges; to supply coolant to each module; the support structure and to hold the modules in the flat surface heater configuration. An optical pyrometer system mounted within the array was designed to monitor specimen surface temperatures without altering the test article's surface.

Source record↗
NASA NTRS1975

Subsonic aerodynamic characteristics of interacting lifting surfaces with separated flow around sharp edges predicted by a vortex-lattice method

Because the potential flow suction along the leading and side edges of a planform can be used to determine both leading- and side-edge vortex lift, the present investigation was undertaken to apply the vortex-lattice method to computing side-edge suction force for isolated or interacting planforms. Although there is a small effect of bound vortex sweep on the computation of the side-edge suction force, the results obtained for a number of different isolated planforms produced acceptable agreement with results obtained from a method employing continuous induced-velocity distributions. By using the method outlined, better agreement between theory and experiment was noted for a wing in the presence of a canard than was previously obtained.

Lamar, J. E.↗
NASA NTRS1975

A Three-Dimensional Solution of Flows over Wings with Leading-Edge Vortex Separation. Part 1: Engineering Document

A method of predicting forces, moments, and detailed surface pressures on thin, sharp-edged wings with leading-edge vortex separation in incompressible flow is presented. The method employs an inviscid flow model in which the wing and the rolled-up vortex sheets are represented by piecewise, continuous quadratic doublet sheet distributions. The Kutta condition is imposed on all wing edges. Computed results are compared with experimental data and with the predictions of the leading-edge suction analogy for a selected number of wing planforms over a wide range of angle of attack. These comparisons show the method to be very promising, capable of producing not only force predictions, but also accurate predictions of detailed surface pressure distributions, loads, and moments.

Brune, G. W.↗