Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “directivity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS2002

Architecture Studies Done for High-Rate Duplex Direct Data Distribution (D4) Services

A study was sponsored to investigate a set of end-to-end system concepts for implementing a high-rate duplex direct data distribution (D4) space-to-ground communications link. The NASA Glenn Research Center is investigating these systems (both commercial and Government) as a possible method of providing a D4 communications service between NASA spacecraft in low Earth orbit and the respective principal investigators using or monitoring instruments aboard these spacecraft. Candidate commercial services were assessed regarding their near-term potential to provide a D4 type of service. The candidates included K-band and V-band geostationary orbit and nongeostationary orbit satellite relay services and direct downlink (D3) services. Internet protocol (IP) networking technologies were evaluated to enable the user-directed distribution and delivery of science data. Four realistic, near-future concepts were analyzed: 1) A duplex direct link (uplink plus downlink communication paths) between a low-Earth-orbit spacecraft and a principal-investigator-based autonomous Earth station; 2) A space-based relay using a future K-band nongeosynchronous-orbit system to handle both the uplink and downlink communication paths; 3) A hybrid link using both direct and relay services to achieve full duplex capability; 4) A dual-mode concept consisting of both a duplex direct link and a space relay duplex link operating independently. The concepts were analyzed in terms of contact time between the NASA spacecraft and the communications service and the achievable data throughput. Throughput estimates for the D4 systems were based on the infusion of advanced communications technology products (single and multibeam K-band phased-arrays and digital modems) being developed by Glenn. Cost estimates were also performed using extrapolated information from both terrestrial and current satellite communications providers. The throughput and cost estimates were used to compare the concepts.

Source record↗
NASA NTRS2007

Noise Spectra and Directivity For a Scale-Model Landing Gear

An extensive experimental study has been conducted to acquire detailed noise spectra and directivity data for a high-fidelity, 6.3%-scale, Boeing 777 main landing gear. The measurements were conducted in the NASA Langley Quiet Flow Facility using a 41-microphone directional array system positioned at a range of polar and azimuthal observer angles with respect to the model. DAMAS (Deconvolution Approach for the Mapping of Acoustic Sources) array processing as well as straightforward individual microphone processing were employed to compile unique flyover and sideline directivity databases for a range of freestream Mach numbers (0.11 - 0.17) covering typical approach conditions. Comprehensive corrections were applied to the test data to account for shear layer ray path and amplitude variations. This allowed proper beamforming at different measurement orientations, as well as directivity presentation in free-field emission coordinates. Four different configurations of the landing gear were tested: a baseline configuration with and without an attached side door, and a noise reduction concept "toboggan" truck fairing with and without side door. DAMAS noise source distributions were determined. Spectral analyses demonstrated that individual microphones could establish model spectra. This finding permitted the determination of unique, spatially-detailed directivity contours of spectral band levels over a hemispherical surface. Spectral scaling for the baseline model confirmed that the acoustic intensity scaled with the expected sixth-power of the Mach number. Finally, comparison of spectra and directivity between the baseline gear and the gear with an attached toboggan indicated that the toboggan fairing may be of some value in reducing gear noise over particular frequency ranges.

Humphreys, William M., Jr.↗
NASA NTRS2000

Lean direct wall fuel injection method and devices

A fuel combustion chamber, and a method of and a nozzle for mixing liquid fuel and air in the fuel combustion chamber in lean direct injection combustion for advanced gas turbine engines, including aircraft engines. Liquid fuel in a form of jet is injected directly into a cylindrical combustion chamber from the combustion chamber wall surface in a direction opposite to the direction of the swirling air at an angle of from about 50.degree. to about 60.degree. with respect to a tangential line of the cylindrical combustion chamber and at a fuel-lean condition, with a liquid droplet momentum to air momentum ratio in the range of from about 0.05 to about 0.12. Advanced gas turbines benefit from lean direct wall injection combustion. The lean direct wall injection technique of the present invention provides fast, uniform, well-stirred mixing of fuel and air. In addition, in order to further improve combustion, the fuel can be injected at a venturi located in the combustion chamber at a point adjacent the air swirler.

Choi, Kyung J.↗
NASA NTRS1994

Directional emittance surface measurement system and process

Apparatus and process for measuring the variation of directional emittance of surfaces at various temperatures using a radiometric infrared imaging system. A surface test sample is coated onto a copper target plate provided with selective heating within the desired incremental temperature range to be tested and positioned onto a precision rotator to present selected inclination angles of the sample relative to the fixed positioned and optically aligned infrared imager. A thermal insulator holder maintains the target plate on the precision rotator. A screen display of the temperature obtained by the infrared imager, and inclination readings are provided with computer calculations of directional emittance being performed automatically according to equations provided to convert selected incremental target temperatures and inclination angles to relative target directional emittance values. The directional emittance of flat black lacquer and an epoxy resin measurements obtained are in agreement with the predictions of the electromagnetic theory and with directional emittance data inferred from directional reflectance measurements made on a spectrophotometer.

Puram, Chith K.↗
NASA NTRS2009

The Development of Directional Decohesion Finite Elements for Multiscale Failure Analysis of Metallic Polycrystals

Atomistic simulations of intergranular fracture have indicated that grain-scale crack growth in polycrystalline metals can be direction dependent. At these material length scales, the atomic environment greatly influences the nature of intergranular crack propagation, through either brittle or ductile mechanisms, that are a function of adjacent grain orientation and direction of crack propagation. Methods have been developed to obtain cohesive zone models (CZM) directly from molecular dynamics simulations. These CZMs may be incorporated into decohesion finite element formulations to simulate fracture at larger length scales. A new directional decohesion element is presented that calculates the direction of Mode I opening and incorporates a material criterion for dislocation emission based on the local crystallographic environment to automatically select the CZM that best represents crack growth. The simulation of fracture in 2-D and 3-D aluminum polycrystals is used to illustrate the effect of parameterized CZMs and the effectiveness of directional decohesion finite elements.

Saether, Erik↗
NASA NTRS2008

Compact Directional Microwave Antenna for Localized Heating

A directional, catheter-sized cylindrical antenna has been developed for localized delivery of microwave radiation for heating (and thus killing) diseased tissue without excessively heating nearby healthy tissue. By "localized" is meant that the antenna radiates much more in a selected azimuthal direction than in the opposite radial direction, so that it heats tissue much more on one side than it does on the opposite side. This antenna can be inserted using either a catheter or a syringe. A 2.4-mm prototype was tested, although smaller antennas are possible. Prior compact, cylindrical antennas designed for therapeutic localized hyperthermia do not exhibit such directionality; that is, they radiate in approximately axisymmetric patterns. Prior directional antennas designed for the same purpose have been, variously, (1) too large to fit within catheters or (2) too large, after deployment from catheters, to fit within the confines of most human organs. In contrast, the present antenna offers a high degree of directionality and is compact enough to be useable as a catheter in some applications.

Fink, Patrick W.↗
NASA NTRS2011

Separating Direct and Indirect Turbofan Engine Combustion Noise While Estimating Post-Combustion (Post-Flame) Residence Time Using the Correlation Function

A previous investigation on the presence of direct and indirect combustion noise for a full-scale turbofan engine using a far-field microphone at 130 is extended by also examining signals obtained at two additional downstream directions using far-field microphones at 110 deg and 160 deg. A generalized cross-correlation function technique is used to study the change in propagation time to the far field of the combined direct and indirect combustion noise signal as a sequence of low-pass filters are applied. The filtering procedure used produces no phase distortion. As the low-pass filter frequency is decreased, the travel time increases because the relative amount of direct combustion noise is reduced. The indirect combustion noise signal travels more slowly because in the combustor entropy fluctuations move with the flow velocity, which is slow compared to the local speed of sound. The indirect combustion noise signal travels at acoustic velocities after reaching the turbine and being converted into an acoustic signal. The direct combustion noise is always propagating at acoustic velocities. The results show that the estimated indirect combustion noise time delay values (post-combustion residence times) measured at each angle are fairly consistent with one another for a relevant range of operating conditions and demonstrate source separation of a mixture of direct and indirect combustion noise. The results may lead to a better idea about the acoustics in the combustor and may help develop and validate improved reduced-order physics-based methods for predicting turbofan engine core noise.

Miles, Jeffrey Hilton↗
NASA NTRS2004

Directional Radio-Frequency Identification Tag Reader

A directional radio-frequency identification (RFID) tag reader has been designed to facilitate finding a specific object among many objects in a crowded room. The device could be an adjunct to an electronic inventory system that tracks RFID-tagged objects as they move through reader-equipped doorways. Whereas commercial RFID-tag readers do not measure directions to tagged objects, the device is equipped with a phased-array antenna and a received signal-strength indicator (RSSI) circuit for measuring direction. At the beginning of operation, it is set to address only the RFID tag of interest. It then continuously transmits a signal to interrogate that tag while varying the radiation pattern of the antenna. It identifies the direction to the tag as the radiation pattern direction of peak strength of the signal returned by the tag. An approximate distance to the tag is calculated from the peak signal strength. The direction and distance can be displayed on a screen. A prototype containing a Yagi antenna was found to be capable of detecting a 915.5-MHz tag at a distance of approximately equal to 15 ft (approximately equal to 4.6 m).

Medelius, Pedro J.↗
NASA NTRS2012

Process Sensitivity, Performance, and Direct Verification Testing of Adhesive Locking Features

Phase I: The use of adhesive locking features or liquid locking compounds (LLCs) (e.g., Loctite) as a means of providing a secondary locking feature has been used on NASA programs since the Apollo program. In many cases Loctite was used as a last resort when (a) self-locking fasteners were no longer functioning per their respective drawing specification, (b) access was limited for removal & replacement, or (c) replacement could not be accomplished without severe impact to schedule. Long-term use of Loctite became inevitable in cases where removal and replacement of worn hardware was not cost effective and Loctite was assumed to be fully cured and working. The NASA Engineering & Safety Center (NESC) and United Space Alliance (USA) recognized the need for more extensive testing of Loctite grades to better understand their capabilities and limitations as a secondary locking feature. These tests, identified as Phase I, were designed to identify processing sensitivities, to determine proper cure time, the correct primer to use on aerospace nutplate, insert and bolt materials such as A286 and MP35N, and the minimum amount of Loctite that is required to achieve optimum breakaway torque values. The .1900-32 was the fastener size tested, due to wide usage in the aerospace industry. Three different grades of Loctite were tested. Results indicate that, with proper controls, adhesive locking features can be successfully used in the repair of locking features and should be considered for design. Phase II: Threaded fastening systems used in aerospace programs typically have a requirement for a redundant locking feature. The primary locking method is the fastener preload and the traditional redundant locking feature is a self-locking mechanical device that may include deformed threads, non-metallic inserts, split beam features, or other methods that impede movement between threaded members. The self-locking resistance of traditional locking features can be directly verified during assembly by measuring the dynamic prevailing torque. Adhesive locking features or LLCs are another method of providing redundant locking, but a direct verification method has not been used in aerospace applications to verify proper installation when using LLCs because of concern for damage to the adhesive bond. The reliability of LLCs has also been questioned due to failures observed during testing with coupons for process verification, although the coupon failures have often been attributed to a lack of proper procedures. It is highly desirable to have a direct method of verifying the LLC cure or bond integrity. The purpose of the Phase II test program was to determine if the torque applied during direct verification of an adhesive locking feature degrades that locking feature. This report documents the test program used to investigate the viability of such a direct verification method. Results of the Phase II testing were positive, and additional investigation of direct verification of adhesive locking features is merited.

Golden, Johnny L.↗
NASA NTRS2016

Directional and Spectral Irradiance in Ocean Models: Effects on Simulated Global Phytoplankton, Nutrients, and Primary Production

The importance of including directional and spectral light in simulations of ocean radiative transfer was investigated using a coupled biogeochemical-circulation-radiative model of the global oceans. The effort focused on phytoplankton abundances, nutrient concentrations and vertically-integrated net primary production. The importance was approached by sequentially removing directional (i.e., direct vs. diffuse) and spectral irradiance and comparing results of the above variables to a fully directionally and spectrally-resolved model. In each case the total irradiance was kept constant; it was only the pathways and spectral nature that were changed. Assuming all irradiance was diffuse had negligible effect on global ocean primary production. Global nitrate and total chlorophyll concentrations declined by about 20% each. The largest changes occurred in the tropics and sub-tropics rather than the high latitudes, where most of the irradiance is already diffuse. Disregarding spectral irradiance had effects that depended upon the choice of attenuation wavelength. The wavelength closest to the spectrally-resolved model, 500 nm, produced lower nitrate (19%) and chlorophyll (8%) and higher primary production (2%) than the spectral model. Phytoplankton relative abundances were very sensitive to the choice of non-spectral wavelength transmittance. The combined effects of neglecting both directional and spectral irradiance exacerbated the differences, despite using attenuation at 500 nm. Global nitrate decreased 33% and chlorophyll decreased 24%. Changes in phytoplankton community structure were considerable, representing a change from chlorophytes to cyanobacteria and coccolithophores. This suggested a shift in community function, from light-limitation to nutrient limitation: lower demands for nutrients from cyanobacteria and coccolithophores favored them over the more nutrient-demanding chlorophytes. Although diatoms have the highest nutrient demands in the model, their relative abundances were generally unaffected because they only prosper in nutrient-rich regions, such as the high latitudes and upwelling regions, which showed the fewest effects from the changes in radiative simulations. The results showed that including directional and spectral irradiance when simulating the ocean light field can be important for ocean biology, but the magnitude varies with variables and regions. The quantitative results are intended to assist ocean modelers when considering improved irradiance representations relative to other processes or variables associated with the issues of interest.

Phytoplankton↗
NASA NTRS2021

S-NPP VIIRS Solar Diffuser Degradation at the View Direction of the Rotating Telescope Assembly

S-NPP VIIRS has been on-orbit for more than nine years since it was launched on October28th,2011. The VIIRS reflective solar bands (RSBs) are calibrated on-orbit primarily by an onboard solar diffuser (SD). The SD on-orbit degradation is tracked by an onboard SD stability monitor(SDSM). The VIIRS RSBs view the SD through a rotating telescope assembly (RTA). The RTA views the SD from a direction that is quite different from that of the SDSM. It has been shown that the SD degrades non-uniformly with respect to the incident and outgoing directions, especially at the short wavelengths. Thus, the SDSM calibration cannot provide an accurate SD degradation estimation for the view direction of the RTA, resulting in long-term drifts in the calibration coefficients derived from the SD and SDSM calibration. S-NPP VIIRS has been scheduled to view the Moon approximately monthly since its launch. The lunar observations can provide accurate long-term trends for the RSB calibration coefficients since the lunar surface reflectance is quite stable. By comparing the SD and lunar calibration results, we can obtain the SD degradation differences at the view directions of the SDSM and RTA and derive the SD degradation at the view direction of the RTA. Moreover, we can also derive the SD degradation in the short-wave infrared (SWIR) spectral range, wherein the SDSM cannot track the SD degradation. In this paper, we will derive the SD degradation for the view direction of the RTA from the SD, SDSM, and lunar calibrations from the visible to SWIR spectral range. We will also simulate the SD degradation with analytical models and compare their performances.

SNPP VIIRS↗
DOE OSTI2025

Evaluating Direct and Indirect Influence on EV Charging Stations Across the US

The adoption of new technology for electric vehicles (EV) and mobility applications can bring underappreciated vulnerabilities to the power grid. One area of potential fraud and adversarial influence is through the business ecosystem of startups that own and deploy EV technology. Yet, there are no models or analyses that map the network of organizations and people that have direct and indirect influence over technologies currently deployed in the grid. To fill this gap, we develop a multilayer network model to measure direct and indirect influence on EV charging stations. First, we create and adversarial socio-technical network (ASTN) model via a data fusion pipeline for different US regions of interest (ROI). Then, we develop an integrated ASTN for Chicago, Los Angeles, New York, and Philadelphia. We rank EV charging companies direct influence within each geographic region as well as indirect influence via social network analysis. While some companies have strong direct and indirect influence (i.e., ChargePoint) others show a mismatch between their influence over charging stations and their position within the social network. For example, Tesla has strong direct influence on stations and weak indirect influence over competitors. In contrast, 7Charge has weak direct influence over stations, but strong indirect influence over competitors.

29 - ENERGY PLANNING, POLICY AND ECONOMY↗
DOE OSTI2023

A Materials Perspective on Direct Recycling of Lithium-Ion Batteries: Principles, Challenges and Opportunities

As the dominant means of energy storage technology today, the widespread deployment of lithium-ion batteries (LIBs) would inevitably generate countless spent batteries at their end of life. From the perspectives of environmental protection and resource sustainability, recycling is a necessary strategy to manage end-of-life LIBs. Compared with traditional hydrometallurgical and pyrometallurgical recycling methods, the emerging direct recycling technology, rejuvenating spent electrode materials via a non-destructive way, has attracted rising attention due to its energy efficient processes along with increased economic return and reduced CO 2 footprint. This review investigates the state-of-the-art direct recycling technologies based on effective relithiation through solid-state, aqueous, eutectic solution and ionic liquid mediums and thoroughly discusses the underlying regeneration mechanism of each method regarding different battery chemistries. It is concluded that direct regeneration can be a more energy-efficient, cost-effective, and sustainable way to recycle spent LIBs compared with traditional approaches. Additionally, it is also identified that the direct recycling technology is still in its infancy with several fundamental and technological hurdles such as efficient separation, binder removal and electrolyte recovery. Finally, in addressing these remaining challenges, this review proposes an outlook on potential technical avenues to accelerate the development of direct recycling toward industrial applications.

25 ENERGY STORAGE↗
DOE OSTI2021

Insights into storm direction effect on flood response

In this study, we investigate the directional influence of storm movement on catchment flood peak response using the synthetic circular basin. Due to the complexity in defining storm movements that require meteorological modeling, we adopt a novel approach of combining the basin rotation method (BRM) with a circular basin construct. A systematic basin rotation approach provides a proxy for the storm direction relative to the river network topology to study its hydrologic response. Using Stage-IV rainfall with 4-km by 1-hour resolution for 16 years period from 2003 to 2018 in Iowa, U.S., we systematically analyze consequent flood peak response due to storm directions (basin rotations) using a distributed hydrologic model called the Hillslope-Link Model (HLM). HLM has demonstrated the ability to reproduce observed streamflow for real river basins studied in Iowa. The hydrologic simulation results show that the BRM can quantify the relationship between the rainstorm direction and catchment hydrologic response. Also, the maximum flood peak response is strongly dependent on the interaction of the peak of the rainstorm with the peak of the width function. The results indicate significant differences in runoff volume and runoff peak and their interannual variability due to rainstorm direction. The study has important implications for flood frequency predictions and developing flood resilience and watershed management strategies, particularly due to changing storm tracks under a warming climate.

42 ENGINEERING↗
DOE OSTI2025

Influence of Metal Ion Complexation on the Radiolytic Longevity of Butyramide Extractants under Direct Dissolution Process Conditions

The direct dissolution of voloxidized used nuclear fuel (UNF) into an organic solution–comprised of diluent and specialized extractants–poses a promising alternative to the traditional liquid–liquid solvent extraction approach to reprocessing UNF. However, moving to direct dissolution removes the presence of a concentrated nitric acid aqueous phase, which has been shown to significantly influence the radiolytic longevity of extractants in conventional extraction flowsheets. Given the limited knowledge of radiation effects under direct dissolution conditions, here we present a time-resolved and dose-accumulation study on the impact of direct dissolution conditions on the radiolytic longevity of two candidate butyramide extractants, N,N-di(2-ethylhexyl) butyramide (DEHBA) and N,N-di(2-ethylhexyl)isobutyramide (DEHiBA), in pre-equilibrated n-dodecane solvent in the presence and absence of process-relevant metal ions, specifically, uranium and rhenium. Loss G(DEHBA) and G(DEHiBA) values were found to be comparable to each other, with an average of 0.37 ± 0.02 μmol J –1 , and to previous data from the γ irradiation of DEHBA and DEHiBA under conventional solvent extraction conditions. Rhenium, and by extension technetium, extraction had a modest decrease (~10%) in the overall radiolytic stability of DEHiBA only, despite >2× observed increases in chemical kinetic reactivity of the corresponding complexes with the n-dodecane radical cation. Uranium loading, on the other hand, significantly improved the lifetime of both ligands (>30%) under γ irradiation, with a greater stabilization observed for DEHBA over DEHiBA. The observed radioprotective effect afforded by uranium loading is fortuitous for the longevity of direct dissolution solvent.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2021

Evidence for the 3D Radiative Effects of Boundary-Layer Clouds From Observations of Direct and Diffuse Surface Solar Fluxes

Numerical experiments have revealed the importance of horizontal transport of light in the presence of clouds (“3D effects”), with consequences for climate, weather, and solar resource availability predictions. Yet, analysis of 3D effects from observations remain sparse because of the difficulty to isolate the effect of horizontal transport in radiation measurements. In this study, we provide observational evidence for 3D effects based on the direct-diffuse partition of surface solar fluxes. It is compared to outputs from the ecRad radiative transfer scheme run on retrieved cloud profiles. Furthermore, the direct-beam calculation takes careful account of the field-of-view of the pyrheliometer to ensure consistency between observed and modeled direct fluxes. Only the solver that accounts for 3D effects is able to reproduce the observed mean direct-diffuse partition as a function of solar zenith angle and cloud cover, in particular at large solar zenith angles where cloud sides intercept most of the direct beam.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Disentangling direct from indirect relationships in association networks

Networks are vital tools for understanding and modeling interactions in complex systems in science and engineering, and direct and indirect interactions are pervasive in all types of networks. However, quantitatively disentangling direct and indirect relationships in networks remains a formidable task. Here, we present a framework, called iDIRECT (Inference of Direct and Indirect Relationships with Effective Copula-based Transitivity), for quantitatively inferring direct dependencies in association networks. Using copula-based transitivity, iDIRECT eliminates/ameliorates several challenging mathematical problems, including ill-conditioning, self-looping, and interaction strength overflow. With simulation data as benchmark examples, iDIRECT showed high prediction accuracies. Application of iDIRECT to reconstruct gene regulatory networks in Escherichia coli also revealed considerably higher prediction power than the best-performing approaches in the DREAM5 (Dialogue on Reverse Engineering Assessment and Methods project, #5) Network Inference Challenge. In addition, applying iDIRECT to highly diverse grassland soil microbial communities in response to climate warming showed that the iDIRECT-processed networks were significantly different from the original networks, with considerably fewer nodes, links, and connectivity, but higher relative modularity. Further analysis revealed that the iDIRECT-processed network was more complex under warming than the control and more robust to both random and target species removal ( P < 0.001). As a general approach, iDIRECT has great advantages for network inference, and it should be widely applicable to infer direct relationships in association networks across diverse disciplines in science and engineering.

59 BASIC BIOLOGICAL SCIENCES↗
NASA NTRS2009

Acoustically Induced Vibration of Structures: Reverberant Vs. Direct Acoustic Testing

Large reverberant chambers have been used for several decades in the aerospace industry to test larger structures such as solar arrays and reflectors to qualify and to detect faults in the design and fabrication of spacecraft and satellites. In the past decade some companies have begun using direct near field acoustic testing, employing speakers, for qualifying larger structures. A limited test data set obtained from recent acoustic tests of the same hardware exposed to both direct and reverberant acoustic field testing has indicated some differences in the resulting structural responses. In reverberant acoustic testing, higher vibration responses were observed at lower frequencies when compared with the direct acoustic testing. In the case of direct near field acoustic testing higher vibration responses appeared to occur at higher frequencies as well. In reverberant chamber testing and direct acoustic testing, standing acoustic modes of the reverberant chamber or the speakers and spacecraft parallel surfaces can strongly couple with the fundamental structural modes of the test hardware. In this paper data from recent acoustic testing of flight hardware, that yielded evidence of acoustic standing wave coupling with structural responses, are discussed in some detail. Convincing evidence of the acoustic standing wave/structural coupling phenomenon will be discussed, citing observations from acoustic testing of a simple aluminum plate. The implications of such acoustic coupling to testing of sensitive flight hardware will be discussed. The results discussed in this paper reveal issues with over or under testing of flight hardware that could pose unanticipated structural and flight qualification issues. Therefore, it is of paramount importance to understand the structural modal coupling with standing acoustic waves that has been observed in both methods of acoustic testing. This study will assist the community to choose an appropriate testing method and test setup in the planning stages.

Reverberant acoustic field↗