SEARCH · Engineering Papers

Results for “cavity flow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

All sources NASA NTRS DOE OSTI

NASA NTRS1992

Navier-Stokes computations of cavity aeroacoustics with suppression devices

Effectiveness of two devices to suppress the cavity acoustics was computationally investigated. Two dimensional, computational simulations were performed for the transonic, turbulent flows past a cavity, which was first equipped with a rear face ramp and then with a spoiler. The Reynolds-averaged, unsteady, compressible, full Navier-Stokes equations were solved time accurately by a second-order accurate, implicit, upwind, finite-volume method. The effect of turbulence was included through a Baldwin-Lomax model with modifications for the multiple-wall effects and for the highly vortical flow with a shear layer. The results included instantaneous and time-averaged flow properties, and time-series analyses of the pressure inside the cavity, which compared favorably with the available experimental data. These results were also contrasted with the computed aeroacoustics of the same cavity (length-to-depth ratio of 4.5), but without a device, to demonstrate the suppression effectiveness.

Baysal, Oktay↗

NASA NTRS1977

Effect of grazing flow on the acoustic impedance of interacting cavity-backed orifices

The two-microphone method was used to investigate the impedance of interacting cavity-backed orifices in the presence of a grazing flow; the investigation has relevance for the control of turbomachinery noise generated within jet engines. The number (varied from one to 16), the diameter, and the spacing of the orifices were the chief parameters studied in the experimental program. It was found that interactions between adjacent orifices, while increasing reactance, do not significantly alter resistance. In addition, the grazing flow appears to reduce the rate of increase of the reactance.

Hersh, A. S.↗

NASA NTRS1977

Measurements of the tonal component of cavity noise and comparison with theory

The frequency of the tonal noise generated by a flow-excited rectangular cavity was measured using Mach numbers ranging from 0.05 to 0.40, and cavity length-to-depth ratios varying from 0.1 to 8. The data are used to evaluate a current prediction method, and good agreement is shown. Measurements of the minimum streamwise cavity length required for oscillation were also made.

Block, P. J. W.↗

NASA NTRS1990

Flow-induced resonance of screen-covered cavities

An experimental study of screen-covered cavities exposed to airflow tangent to the screen is described. The term screen refers to a thin metal plate perforated with a repetitive pattern of round holes. The purpose was to find the detailed aerodynamic and acoustic mechanisms responsible for screen-covered cavity resonance and to find ways to control the pressure oscillations. Results indicate that strong cavity acoustic resonances are created by screen orifices that shed vortices which couple resonance by choosing hole spacings such that shed vortices do not arrive at a downstream orifice in synchronization with cavity pressure oscillations. The proper hole pattern is effective at all airspeeds. It was also discovered that a reduction of orifice size tended to weaken the screen/cavity interaction regardless of hole pattern, probably because of viscous flow losses at the orifices. The screened cavities that resonated did so at much higher frequencies than the equivalent open cavity. The classical large eddy phenomenon occurs at the relatively small scale of the orifices (the excitation is typically of high frequency). The wind tunnel study was made at airspeeds from 0 to 100m/sec. The 457-mm-long by 1.09-m-high rectangular cavities had length-to-depth ratios greater than one, which is indicative of shallow cavities. The cavity screens were perforated in straight rows and columns with hole diameters ranging from 1.59 to 6.35 mm and with porosities from 2.6 to 19.6 percent.

Soderman, Paul T.↗

NASA NTRS1984

A numerical study of the 2- and 3-dimensional unsteady Navier-Stokes equations in velocity-vorticity variables using compact difference schemes

A compact finite-difference approximation to the unsteady Navier-Stokes equations in velocity-vorticity variables is used to numerically simulate a number of flows. These include two-dimensional laminar flow of a vortex evolving over a flat plate with an embedded cavity, the unsteady flow over an elliptic cylinder, and aspects of the transient dynamics of the flow over a rearward facing step. The methodology required to extend the two-dimensional formulation to three-dimensions is presented.

Gatski, T. B.↗

NASA NTRS1984

A numerical study of the two- and three-dimensional unsteady Navier-Stokes equations in velocity-vorticity variables using compact difference schemes

Gatski, T. B.↗

NASA NTRS1992

Interference flows past cylinder-fin-sting-cavity assemblies

Explore the source record for details and available documents.

Baysal, O.↗

NASA NTRS2008

Heating Augmentation in Laminar Flow Due to Heat-Shield Cavities on the Project Orion CEV

An experimental study has been conducted to assess the effects of compression pad cavities on the aeroheating environment of the Project Orion CEV heat-shield at laminar conditions. Testing was conducted in Mach 6 and Mach 10 perfect-gas wind tunnels to obtain heating measurements on and around the compression pads using global phosphor thermography. Consistent trends in heating augmentation levels were observed in the data and correlations of average and maximum heating at the cavities were formulated in terms of the local boundary-layer parameters and cavity dimensions. Additional heating data from prior testing of Genesis and Mars Science Laboratory models were also examined to extend the parametric range of cavity heating correlations.

Hollis, Brian R.↗

NASA NTRS2003

Flow Field Measurement of Mixing Driven by Buoyancy

Mixing driven by buoyancy-induced flows inside a cavity consists of stretching and folding of an interface. Measurement of the flow field using particle imaging velocimetry shows that during stretching the flow field has a single elliptic point, thus dominated by a single vortex. However, global bifurcation that results in folding introduces a hyperbolic point whereby the flow field degenerates to multiple vortex interactions. The short-lived coherent structure observed during mixing which results in the Rayleigh- Taylor morphology is attributed to vortex interactions. The mixing characteristics of non-homogeneous fluids driven by buoyancy are important towards understanding transport phenomenon in a microgravity environment. Mixing consists of stretching and folding of an interface due to a flow field whose intensity depends on the body force. For miscible liquids, the characteristic of the flow field determines whether mass transport is governed by diffusion or bulk stirring which induces mixing. For technologically important processes, transport of mass is governed by the coupling of the body force to scalar gradients such as concentration and or temperature' 2 3 . In order to lend insight into these classes of problems we consider a model experimental system to study mixing driven by buoyancy-induced flows. The characteristics of mixing is addressed from detail measurements of the flow field using particle imaging velocimetry (PIV), and its corresponding interface dynamics using image processing techniques.

Batur, C.↗

NASA NTRS2004

Assessment of LAURA for Laminar Supersonic Shallow Cavities

The ability of the Laura flow solver to predict local heating augmentation factors for shallow cavities is assessed. This assessment is part of a larger e ort within the Space Shuttle return-to-flight program to develop technologies to support on-orbit tile repair decisions. The comparison is made against global phosphor thermography images taken in the Langley Aerothermodynamic Laboratory 20-Inch Mach 6 Air Tunnel. The cavities are rectangular in shape, with lengths L/H of 14 20 and depths H/ of 1.1 5.2. The fully laminar results, for Re = 300, show good agreement between the data sets. For Re = 503, the wind tunnel data indicates boundary layer transition with turbulent flow both within and downstream of the cavity. The turbulent flow structures are significantly di erent from the laminar predictions, with order of magnitude increases in the heating augmentations. Because of the di erent flow structures, no simple bump factor can be used to correct the laminar calculations to account for the turbulent heating levels. A fine gradation in wind tunnel cases will be required to clearly delineate the laminar-to-turbulent transition point, and hence the limits of applicability of the laminar numerical approach.

Wood, William A.↗

NASA NTRS1994

Wind Tunnel Testing for the Stratospheric Observatory for Infrared Astronomy

NASA Ames Research Center is pursuing the development of SOFIA, the Stratospheric Observatory For Infrared Astronomy. SOFIA will consist of a 2.5 meter telescope mounted aft of the wing of a Boeing 747 aircraft. Since a large portion of the infrared spectrum is not visible at ground level due to absorption by water vapor in the atmosphere below 40,000 feet, it is highly desirable to make observations above this altitude. SOFIA will provide the opportunity for astronomers to conduct high-altitude research for extended periods of time. Current study is focused on wind tunnel testing for the open cavity. If not controlled, air would create resonance and damage the telescope. For this reason, SOFIA will design a boundary layer control device to achieve laminar flow over the cavity. This also provides a clearer flow for seeing, thus improving resolution on infrared sources. Other effects being tested in the wind tunnel are aerodynamic torque loads on the telescope, and flutter loads on the tail.

Schenberger, Deborah↗

NASA NTRS2008

Flow Solver for Incompressible Rectangular Domains

This is an extension of the Flow Solver for Incompressible 2-D Drive Cavity software described in the preceding article. It solves the Navier-Stokes equations for incompressible flow using finite differencing on a uniform, staggered grid. There is a runtime choice of either central differencing or modified upwinding for the convective term. The domain must be rectangular, but may have a rectangular walled region within it. Currently, the position of the interior region and exterior boundary conditions are changed by modifying parameters in the code and recompiling. These features make it possible to solve a variety of classical fluid flow problems such as an L-shaped cavity, channel flow, or wake flow past a square cylinder. The code uses fourth-order Runge-Kutta time-stepping and overall second-order spatial accuracy. This software permits the walled region to be positioned such that flow past a square cylinder, an L-shaped cavity, and the flow over a back-facing step can all be solved by reconfiguration. Also, this extension has an automatic detection of periodicity, as well as use of specialized data structure for ease of configuring domain decomposition and computing convergence in overlap regions.

Kalb, Virginia L.↗

NASA NTRS1976

Heat transfer evaluation in a plasma core reactor

Numerical evaluations of heat transfer in a fissioning uranium plasma core reactor cavity, operating with seeded hydrogen propellant, was performed. A two-dimensional analysis is based on an assumed flow pattern and cavity wall heat exchange rate. Various iterative schemes were required by the nature of the radiative field and by the solid seed vaporization. Approximate formulations of the radiative heat flux are generally used, due to the complexity of the solution of a rigorously formulated problem. The present work analyzes the sensitivity of the results with respect to approximations of the radiative field, geometry, seed vaporization coefficients and flow pattern. The results present temperature, heat flux, density and optical depth distributions in the reactor cavity, acceptable simplifying assumptions, and iterative schemes. The present calculations, performed in cartesian and spherical coordinates, are applicable to any most general heat transfer problem.

Smith, D. E.↗

NASA NTRS1987

Effect of shaft rotation on the incompressible flow in a labyrinth seal

The incompressible flow in a labyrinth seal at low leakage rates was computationally and experimentally investigated over a wide range of seal rotation rates. QUICK differencing was employed in the finite difference code to reduce the effects of false diffusion. The use of measured inlet boundary conditions for the axial and swirl velocity components and for the turbulent kinetic energy resulted in good agreement between velocity predictions and hot-film measurements. It was found that when the rotation rate is increased beyond a certain point, a second recirculation zone forms inside the seal cavity, altering the flow field in the cavity and resulting in a substantial increase in the pressure drop across it.

Demko, J. A.↗

NASA NTRS1980

Flow visualization techniques in the Airborne Laser Laboratory program

A turret/fairing assembly for laser applications was designed and tested. Wind tunnel testing was conducted using flow visualization techniques. The techniques used have included the methods of tufting, encapsulated liquid crystals, oil flow, sublimation and schlieren and shadowgraph photography. The results were directly applied to the design of fairing shapes for minimum drag and reduced turret buffet. In addition, the results are of primary importance to the study of light propagation paths in the near flow field of the turret cavity. Results indicate that the flow in the vicinity of the turret is an important factor for consideration in the design of suitable turret/fairing or aero-optic assemblies.

Walterick, R. E.↗

NASA NTRS1988

Passive venting system for modifying cavity flowfields at supersonic speeds

The drag of airfoils in transonic flow can be reduced through the use of a passive venting system that employs a porous plate for part of the airfoil upper surface with a vent chamber underneath the porous plate Attention is given to the results obtained with a wind tunnel model employing such a porous floor system. This passive venting system has been used to extend the length/height value before the onset of high drag-producing closed cavity flow at supersonic speeds.

Wilcox, Floyd J., Jr.↗

NASA NTRS1977

Aerodynamic heating in large cavities in an array of RSI tiles

A large panel of reusable surface insulation (RSI) tiles including lost tile cavities was aerothermally tested in the Langley 8 foot high temperature structures tunnel to determine both the heat load within the cavities and the structural performance of the RSI surrounding the cavities. Tests were conducted with a turbulent boundary layer at a nominal free stream Mach number of 6.6, a total temperature of 1800 K, a Reynolds number per meter of 5 million, and a dynamic pressure of 62 kPa. The maximum aerodynamic heating to the floor of the cavity was two to three times the normal surface heating. The cavity heating rates agreed with data from other facilities and were successfully correlated with an empirical equation. A zippering failure occurred to a tile downstream of a double tile cavity when the separated flow attached to the floor of the cavity and forced the tile from its position.

Hunt, L. R.↗

NASA NTRS1993

Incompressible Navier-Stokes Calculations in Pump Flows

Flow through pump components, such as the SSME-HPFTP Impeller and an advanced rocket pump impeller, is efficiently simulated by solving the incompressible Navier-Stokes equations. The solution method is based on the pseudo compressibility approach and uses an implicit-upwind differencing scheme together with the Gauss-Seidel line relaxation method. The equations are solved in steadily rotating reference frames and the centrifugal force and the Coriolis force are added to the equation of motion. Current computations use one-equation Baldwin-Barth turbulence model which is derived from a simplified form of the standard k-epsilon model equations. The resulting computer code is applied to the flow analysis inside an 11-inch SSME High Pressure Fuel Turbopump impeller, and an advanced rocket pump impeller. Numerical results of SSME-HPFTP impeller flow are compared with experimental measurements. In the advanced pump impeller, the effects of exit and shroud cavities are investigated. Flow analyses at design conditions will be presented.

Kiris, Cetin↗