Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “cathode utilization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

Integrated reactor architecture of conductive network and catalytic nodes to accelerate polysulfide conversion for durable and high-loading Li-S batteries

The development of carbon-based heterogeneous framework host with synergistic catalytic and conductive effects for sulfur cathode is a promising strategy to realize high performance lithium sulfur batteries (LSBs). Here, an integrated reactor architecture with defective carbon nodes (IRA-DC) is designed for serving as high-loading (92.4 wt%) sulfur host. The hierarchical porous IRA-DC consists of untangled conductive carbon nanotube network and Co/N co-doped catalytic nodes with high dispersity. Therein the optimization of electric field distribution and homogenization of adsorption-catalysis sites offer the multi-electron conversion reaction of polysulfides with excellent kinetics and stability. The resultant IRA-DC/S cathode enables a high areal capacity of 8.86 mAh cm -2 under ultra-high sulfur loading (13.1 mg cm -2 ) and lean electrolyte (8 μL mg sulfur -1 ). It also displays a long-term cycling performance (1200 cycles at 1 C) and ultrahigh rate performance up to 20 C (with a capacity of 473.6 mAh g -1 ). In conclusion, this work provides an electrode building strategy by optimizing the environments of heterogeneous electrocatalysis and micro electric field to activate the polysulfide conversion efficiency and utilization of high-loading sulfur in monolithic sulfur-carbon cathodes.

25 ENERGY STORAGE↗

Studying the SBND Cathode Structure

The Short-Baseline Near Detector (SBND) is a Liquid Argon Time Projection Chamber (LArTPC) located at Fermilab. It utilizes electrons ionized by passing particles inside the detector to create 3D reconstructions of interactions. This is achieved by drifting ionized electrons towards the instrumented wire planes. Structurally, the cathode can be mapped using cosmic ray muons by using information of their trajectories and their timing. This study shows that the cathode has rich structure. Though preliminary, this work shows evidence of non-negligible effects and warrants further investigation of these structures which could lead to improved detector simulations and more reliable event reconstructions.

Cataldo, Aedan [Notre Dame U.]↗

The Elusive “Life” of LEDs: How TM-21 Contributes to the Solution

This magazine article discusses the issue of LED 'lifetime' and explains where TM-21 plays as part of the solution to this issue. In August 2011, the Illuminating Engineering Society (IES) published the TM-21 document entitled 'Lumen degradation lifetime estimation method for LED light sources.' TM-21 is the IES-recommended method for projecting lumen degradation of an LED package, array or module based on data collected according to LM-80. The lighting community expects TM-21 to become the standard method for projecting useful LED lighting product life at realistic operating temperature. This article presents the development process behind TM-21, and clarifies how and when to apply the lifetime extrapolation method to arrive at reasonable and useful estimations. Why TM-21 and why now? We are all familiar with the very real but sometimes exaggerated long-life attributes of LED technology. Not the least of these is the potential for very long life that helps make it an attractive design choice. The trick has been and continues to be how to measure or estimate this longevity to provide assurance to users of this technology's reliability (life) compared to other options. We also understand that the overall reliability of a complete LED lighting fixture can be affected by the reliability of individual product components (driver, lens, etc.) and should be accounted for in lifetime estimations. The useful life of standard lighting technologies is defined as the time to filament or cathode failure. For most of these lamps, the time period prior to failure exhibits acceptable levels of light output, as shown with the solid lines in Fig. 1. This makes it easy to determine when to replace the lamp. However, LEDs do not have filament burn-out that conveniently announces the end of life (dashed line in Fig. 1). Further, the rapid development of the technology and the desire to bring products to market in a timely manner does not allow for actual testing verification of the long lives claimed (100,000 or even 35,000 hours). As a result, the industry has come to accept a definition of the end of the useful life of an LED as the point when it no longer provides a specified level of light output. And finally, the life and performance of LED lighting products depends greatly on excess heat retained at the diode. This is why LEDs require testing at multiple temperatures such that when a source is installed in a luminaire, its actual operating temperature can be measured and lumen depreciation of the product can be derived. Therefore, to serve the solid-state lighting industry, the Technical Procedures Committee (TPC) of the IES proceeded to develop appropriate tests for use in rating LED product longevity. The initial need was a measure of the basic lumen degradation of LED source components identified by a module, package, or array of diodes and this came in the form of LM-80. Importantly, LM-80 only specifies how to measure lumen depreciation to a minimum of 6000 hours (but recommends testing to 10,000 hours or longer). LM-80 stops short of using that data to estimate any depreciation after that, which is where TM-21 comes in. The TM-21 working group (WG) as part of the IES TPC was formed to develop the lumen depreciation projection method and spent over three years exploring many options. The WG evaluated various projection options starting with an analysis of various mathematical, engineering-based models to provide effective depreciation fit and a useful projection method. Next, the WG analyzed LED lumen maintenance behavior using over 40 sets of LM-80-08 test data (20 sets with 10,000 hours or more) collected from four major LED manufacturers. The working group also examined the accuracy of proposed projections using various proposed models and LM-80 data that extended up to 15,000 hours.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Origins of Irreversibility in Layered NaNi x Fe y Mn z O 2 Cathode Materials for Sodium Ion Batteries

Layered NaNi x Fe y Mn z O 2 cathode (NFM) is of great interest in sodium ion batteries due to its high theoretical capacity and utilization of abundant, low-cost, environmentally-friendly raw materials. Nevertheless, there remains insufficient understanding on the concurrent local environment evolution in each transition metal (TM) that largely influences the reversibility of the cathode materials upon cycling. In this work, we investigate the reversibility of TM ions in layered NFMs with varying Fe contents and potential windows. Utilizing ex situ synchrotron X-ray absorption near edge spectroscopy (XANES) and extended X-ray absorption fine structure (EXAFS) of pre-cycled samples the valence and bonding evolution of the TMs are elucidated. It is found that Mn is electrochemically inactive as indicated by the insignificant change of Mn valence and Mn-O bonding distance. Fe is electrochemically inactive after the first five cycles. The Ni redox couple contributes most of the charge compensation for NFMs. Ni redox is quite reversible in the cathodes with less Fe contents. Furthermore, the Ni redox couple shows significant irreversibility with high Fe content of 0.8. The electrochemical reversibility of the NFM cathode becomes increasingly enhanced with the decrease of either Fe content or with lower upper charge cutoff potential.

25 ENERGY STORAGE↗

Understanding the Redox Obstacles in High Sulfur-Loading Li–S Batteries and Design of an Advanced Gel Cathode

Lithium-sulfur batteries with a high energy density are being considered a promising candidate for next-generation energy storage. However, realization of Li-S batteries is plagued by poor sulfur utilization due to the shuttle of intermediate lithiation products between electrodes and its dynamic redistribution. To optimize the sulfur utilization, an understanding of its redox behavior is essential. Here in this paper, we report a gel cathode consisting of a polysulfide-impregnated O- and N-doped porous carbon and an independent, continuous, and highly conducting 3-dimensional graphite film as the charge-transfer network. This design decouples the function of electron conduction and polysulfide absorption, which is beneficial for understanding the sulfur redox behavior and identifying the dominant factors leading to cell failure when the cells have high sulfur content and insufficient electrolyte. In conclusion, this design also opens up new prospects of tuning the properties of Li-S batteries via separately designing the material functions of electron conduction and polysulfide absorption.

25 ENERGY STORAGE↗

The Impact of Different Substituents in Fluorinated Cyclic Carbonates in the Performance of High Voltage Lithium-Ion Battery Electrolyte

Ethylene carbonate (EC) has been used as the Solid-Electrolyte Interphase (SEI) former in the conventional electrolyte for decades. However, its low anodic stability leads to severe capacity decay during cycling under high voltage operation. Therefore, finding a viable electrolyte with high anodic stability and the ability to form robust SEI for high voltage lithium-ion batteries is of primary importance. In this study, a series of electrolytes containing various fluorinated cyclic carbonates as the SEI former have been designed, synthesized and evaluated. Linear sweep voltammetry study suggested that fluorinated cyclic carbonates generally possess higher anodic stability than EC. Based on the cycling performance of LiNi 0.5 Co 0.2 Mn 0.3 O 2 (NMC532)/ graphite full cells, the electrolyte with DFEC/FEMC (1.0 M LiPF 6 ) inhibited the oxidation side reaction on the cathode and forms a vigorous SEI on the anode. The high voltage NMC532/Graphite cell utilizing the novel electrolyte exhibits excellent cycling durability under both room and elevated temperature. The superior performance of the DFEC based electrolyte was further unveiled by SEM, EDAX and XRD. Both the anode and cathode of the full cell employing DFEC based electrolyte retained their intrinsic structures after cycling while the electrodes cycled in conventional electrolyte showed severe degradation.

25 ENERGY STORAGE↗

Sulfur cathode based on layered carbon matrix for high-performance Li–S batteries

A novel carbon/sulfur composite has been fabricated by means of thermal and hydro-thermal treatments to serve as the cathode in Li -S batteries. The carbon matrix consists of graphene nanosheet (GS) and multiwalled carbon nanotube (MWCNT). The "GS/MWCNT@S" composite allows for infiltration of electrolyte into the cathode, assists in entrapment of polysulfide intermediates, and accommodates some of the stress and volume expansion that occurs during charge discharge processes. In addition, the uniform distribution of sulfur in the conductive carbon matrix promotes utilization of the active materials. A Li-S cell containing the GS/MWCNT@S cathode delivered a capacity of 1290.8 mAh/g and exhibited stable specific capacities up to 612.1 mAh/g after 200 cycles at 0.1 C. These results demonstrate that this cathode material is a promising candidate for rechargeable lithium batteries with high energy density.

Carbon matrix↗

Probing Electrochemically Induced Structural Evolution and Oxygen Redox Reactions in Layered Lithium Iridate

In order to exploit electrochemical capacity beyond the traditionally-utilized transition metal redox reactions in lithium-metal-oxide cathode materials, it is necessary to understand the role that oxygen ions play in the charge compensation mech-anisms, i.e., to know the conditions triggering electron transfer on the oxygen ions and whether this transfer is correlated with battery capacity. Theoretical and experimental investigations of a model cathode material, Li-rich layered Li 2 IrO 3 , have been performed to study the structural and electronic changes induced by electrochemical delithiation in a lithium-ion cell. First-principles density functional theory (DFT) calculations were used to compute the voltage profile of a Li/Li 2-x IrO 3 cell at various states of charge, and the results were in good agreement with electrochemical data. Electron energy loss spectroscopy (EELS), X-ray absorption near-edge spectroscopy (XANES), resonant/non-resonant X-ray emission spectroscopy (XES), and first principles core-level spectra simulations using the Bethe Salpeter Equation (BSE) approach were used to probe the change in oxygen electronic states over the $x$ = 0 to 1.5 range. The correlated Ir M 3 -edge XANES and O K-edge XANES data provided evidence that oxygen hole states form during the early stage of delithiation at ~3.5 V due to the interaction between O $p$ and Ir $d$ states, with Ir oxidation being the dominant source of electrochemical capacity. At higher potentials, the charge capacity was predominantly attributed to oxidation of the O 2- ions. It is argued that the emergence of oxygen holes alone is not necessarily indicative of electrochemical capacity beyond transition metal oxidation, since oxygen hole states can appear as a result of enhanced mixing of O $p$ and Ir $d$ states. Prevailing mechanisms accounting for the oxygen redox mechanism in Li-rich materials were examined by theoretical and experimental X-ray spectroscopy; however, no unambiguous spectroscopic signatures of oxygen dimer interaction or non-bonding oxygen states were identified.

25 ENERGY STORAGE↗

Design and investigation of a multichannel laser-triggered vacuum switch

A laser-triggered vacuum switch (LTVS) is an advanced closing switch with nanosecond delay and jitter. In order to enhance hold-off voltage and extend the service lifetime of an LTVS, we designed a multichannel laser-triggered vacuum switch (MLTVS) utilizing a cone-shaped target electrode placed on the cathode platform. The fabrication and testing of the MLTVS is described in this paper. Experimental results show that the working voltage of the MLTVS with a gap distance of 12 mm is from 30 V to 20 kV. The threshold energy for triggering the switch is 0.4 mJ corresponding to a peak power density of 27.9 MW/cm{sup 2}. The triggering lifetime of a spot can reach up to 18 000 shots. In addition, the relationship between triggering lifetime and target materials is analyzed using a field emission scanning electron microscope. A hypothesis of the vacuum gap’s triggering mechanism is discussed based on the measured results.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Analysis of SOFCs Using Reference Electrodes

Reference electrodes are frequently applied to isolate the performance of one electrode in a solid oxide fuel cell. However, reference electrode simulations raise doubt to veracity of data collected using reference electrodes. The simulations predict that the reported performance for the one electrode will frequently contain performance of both electrodes. Nonetheless, recent reports persistently treat data so collected as ideally isolated. This work confirms the predictions of the reference electrode simulations on two SOFC designs, and to provides a method of validating the data measured in the 3-electrode configuration. Validation is based on the assumption that a change in gas composition to one electrode does not affect the impedance of the other electrode at open circuit voltage. This assumption is supported by a full physics simulation of the SOFC. Three configurations of reference electrode and cell design are experimentally examined using various gas flows and two temperatures. Impedance data are subjected to deconvolution analysis and equivalent circuit fitting and approximate polarization resistances of the cathode and anode are determined. The results demonstrate that the utility of reference electrodes is limited and often wholly inappropriate. Reported impedances and single electrode polarization values must be scrutinized on this basis.

30 DIRECT ENERGY CONVERSION↗

Density functional theory investigation of the electronic structure and defect chemistry of Sr1-xKxFeO3

Solid oxide fuel cells (SOFCs) efficiently generate electricity, but high operating temperatures (T op > 800 °C) limit their utility. Reducing T op requires mixed ion–electron conducting (MIEC) cathode materials. Density functional theory is used here to investigate the role of potassium substitutions in the MIEC material Sr1-x K x FeO3 (SKFO). We predict that such substitutions are endothermic. SrFeO3 and SKFO have nearly identical metallic electronic structures. Oxygen vacancy formation energies decrease by ~0.2 eV when x K increases from 0 to 0.0625. SKFO is a promising SOFC MIEC cathode material; however, further experimental investigations must assess its long-term stability at the desired operating temperatures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Electrodeposition of Nanostructured Copper on Gas Diffusion Layers as Electrocatalysts for Carbon Dioxide Reduction

The aim of the summer project was to immobilize copper nanostructures on gas diffusion layers to serve as electrocatalysts for the electrochemical reduction of CO 2 . Gas diffusion layers are typically bilayer structures consisting of a macro-porous backing material (carbon fiber paper) and a microporous, carbon-based layer (MPL). Classically, the copper catalysts are loaded on the microporous layer. Furthermore, the GDL is intrinsically hydrophobic due to polytetrafluoroethylene (PTFE)in its chemical composition, with the MPL having a more hydrophobic character due to its higher PTFE content. While beneficial for rendering the MPL impervious to electrolytes during actual CO 2 reduction, the hydrophobicity precludes sufficient wetting of the MPL layer, preventing conformal, uniformly distributed and strongly adhered deposits. A two electrode electrodeposition system was used to facilitate copper deposition. An implication of this system is the inability to ascertain or accurately modulate the cathodic over-potential. Hence, galvanostatic (current control) procedures are utilized for all deposition. To improve the wetting behavior of the MPL, the surface is subjected to surface pretreatment protocols prior to electrodeposition. In addition, as morphology of deposits play a role in their efficacy as catalysts in terms of selectivity and conversion, we systematically investigate the effects of different galvanostatic deposition procedures on copper morphology.

36 MATERIALS SCIENCE↗

Enhanced Electrochemical Performance of Disordered Rocksalt Cathodes Enabled by a Graphite Conductive Additive

Cobalt-free cation-disordered rocksalt (DRX) cathodes are a promising class of materials for next-generation Li-ion batteries. Although they have high theoretical specific capacities (>300 mA h/g) and moderate operating voltages (~3.5 V vs Li/Li + ), DRX cathodes typically require a high carbon content (up to 30 wt %) to fully utilize the active material which has a detrimental impact on cell-level energy density. To assess pathways to reduce the electrode’s carbon content, the present study investigates how the carbon’s microstructure and loading (10–20 wt %) influence the performance of DRX cathodes with the nominal composition Li 1.2 Mn 0.5 Ti 0.3 O 1.9 F 0.1 . While electrodes prepared with conventional disordered carbon additives (C65 and ketjenblack) exhibit rapid capacity fade due to an unstable cathode/electrolyte interface, DRX cathodes containing 10 wt % graphite show superior cycling performance (e.g., reversible capacities ~260 mA h/g with 85% capacity retention after 50 cycles) and rate capability (~135 mA h/g at 1000 mA/g). Furthermore, a suite of characterization tools was employed to evaluate the performance differences among these composite electrodes. Overall, these results indicate that the superior performance of the graphite-based cathodes is largely attributed to the: (i) formation of a uniform graphitic coating on DRX particles which protects the surface from parasitic reactions at high states of charge and (ii) homogeneous dispersion of the active material and carbon throughout the composite cathode which provides a robust electronically conductive network that can withstand repeated charge–discharge cycles. Overall, this study provides key scientific insights on how the carbon microstructure and electrode processing influence the performance of DRX cathodes. Based on these results, exploration of alternative routes to apply graphitic coatings is recommended to further optimize the material performance.

25 ENERGY STORAGE↗

Spectroscopic investigation of early light emission from anode-initiated surface flashover in vacuum

Time-resolved optical emission spectroscopy is used to explore the early development of anode-initiated flashover in vacuum. An experimental apparatus for collecting flashover self-luminosity is introduced, which enables spatially resolved light collection from regions adjacent to the anode and cathode triple junctions. The emitted light is spectrally and temporally resolved utilizing an imaging spectrograph and a fast electronic shutter camera. The first light detectable from flashovers across both Rexolite and polytetrafluoroethylene (PTFE) insulators begins less than 10 ns prior to the flashover gap's impedance collapse and consists of faint broadband feature in primarily visible wavelengths. This suggests luminosity due to excitation in the solid, possibly occurring as a result of field emitted electrons. In the few nanoseconds leading up to and including the impedance collapse, the broadband spectrum grows in intensity and extends into the UV, eventually accompanied by a few emission lines of the insulator material. This is strong evidence that the early stages of anode-initiated flashover include surface layer breakdown of the insulator, as a contrast from cathode-initiated flashover, which is predominately an above-surface process. Spectra accumulated over longer exposures of PTFE flashovers indicate that, in the first few hundred nanoseconds after the impedance collapse, ions from the insulator material constitute the majority of the emission lines. Later, neutral and ionic metal species from the electrode contribute with similar prominence as well as molecular bands from diatomic carbon. Finally, a comparison is provided of the results of these studies to other spectroscopic investigations of vacuum flashover from the literature.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

A core–shell electrode for dynamically and statically stable Li–S battery chemistry

Sulfur is an appealing cathode material for establishing advanced lithium batteries as it offers a high theoretical capacity of 1675 mA h g -1 at low material and operating costs. However, the lithium–sulfur (Li–S) electrochemical cells face several formidable challenges arising from both the materials chemistry (e.g., low electrochemical utilization of sulfur and severe polysulfide diffusion) and battery chemistry (e.g., dynamic and static instability and low sulfur loadings). Here in this study, we present the design of a core–shell cathode with a pure sulfur core shielded within a conductive shell-shaped electrode. The new electrode configuration allows Li–S cells to load with a high amount of sulfur (sulfur loadings of up to 30 mg cm -2 and sulfur content approaching 70 wt%). The core–shell cathodes demonstrate a superior dynamic and static electrochemical stability in Li–S cells. The high-loading cathodes exhibit (i) a high sulfur utilization of up to 97% at C/20–C/2 rates and (ii) a low self-discharge during long-term cell storage for a three-month rest period and at different cell-storage conditions. Finally, a polysulfide-trap cell configuration is designed to evidence the eliminations of polysulfide diffusion and to investigate the relationship between the electrode configuration and electrochemical characteristics. Finally, the comprehensive analytical results based on the high-loading cathodes suggest that (i) the core–shell cathode is a promising solution for designing highly reversible Li–S cells and (ii) the polysulfide-trap cell configuration is a viable approach to qualitatively evaluating the presence or absence of polysulfide diffusion.

25 ENERGY STORAGE↗

Cathode porosity is a missing key parameter to optimize lithium-sulfur battery energy density

While high sulfur loading has been pursued as a key parameter to build realistic high-energy lithium-sulfur batteries, less attention has been paid to the cathode porosity, which is much higher in sulfur/carbon composite cathodes than in traditional lithium-ion battery electrodes. For high-energy lithium-sulfur batteries, a dense electrode with low porosity is desired to minimize electrolyte intake, parasitic weight, and cost. Here we report the profound impact on the discharge polarization, reversible capacity, and cell cycling life of lithium-sulfur batteries by decreasing cathode porosities from 70 to 40%. According to the developed mechanism-based analytical model, we demonstrate that sulfur utilization is limited by the solubility of lithium-polysulfides and further conversion from lithium-polysulfides to Li2S is limited by the electronically accessible surface area of the carbon matrix. Finally, we predict an optimized cathode porosity to maximize the cell level volumetric energy density without sacrificing the sulfur utilization.

25 ENERGY STORAGE↗

Superionic conducting vacancy-rich β-Li 3 N electrolyte for stable cycling of all-solid-state lithium metal batteries

The advancement of all-solid-state lithium metal batteries requires breakthroughs in solid-state electrolytes (SSEs) for the suppression of lithium dendrite growth at high current densities and high capacities (>3 mAh cm -2 ) and innovation of SSEs in terms of crystal structure, ionic conductivity and rigidness. Here we report a superionic conducting, highly lithium-compatible and air-stable vacancy-rich β-Li 3 N SSE. This vacancy-rich β-Li 3 N SSE shows a high ionic conductivity of 2.14 × 10 -3 S cm -1 at 25 °C and surpasses almost all the reported nitride-based SSEs. A Li- and N-vacancy-mediated fast lithium-ion migration mechanism is unravelled regarding vacancy-triggered reduced activation energy and increased mobile lithium-ion population. All-solid-state lithium symmetric cells using vacancy-rich β-Li 3 N achieve breakthroughs in high critical current densities up to 45 mA cm -2 and high capacities up to 7.5 mAh cm -2 , and ultra-stable lithium stripping and plating processes over 2,000 cycles. The high lithium compatibility mechanism of vacancy-rich β-Li 3 N is unveiled as intrinsic stability to lithium metal. In addition, β-Li 3 N possesses excellent air stability through the formation of protection surfaces. All-solid-state lithium metal batteries using the vacancy-rich β-Li 3 N as SSE interlayers and lithium cobalt oxide (LCO) and Ni-rich LiNi 0.83 Co 0.11 Mn 0.06 O 2 (NCM83) cathodes exhibit excellent battery performance. Extremely stable cycling performance is demonstrated with high capacity retentions of 82.05% with 95.2 mAh g -1 over 5,000 cycles at 1.0 C for LCO and 92.5% with 153.6 mAh g -1 over 3,500 cycles at 1.0 C for NCM83. Utilizing the vacancy-rich β-Li 3 N SSE and NCM83 cathodes, the all-solid-state lithium metal batteries successfully accomplished mild rapid charge and discharge rates up to 5.0 C, retaining 60.47% of the capacity. Notably, these batteries exhibited a high areal capacity, registering approximately 5.0 mAh cm -2 for the compact pellet-type cells and around 2.2 mAh cm -2 for the all-solid-state lithium metal pouch cells.

25 ENERGY STORAGE↗

Hybrid DFT investigation of the energetics of Mg ion diffusion in α-MoO 3

We report that rechargeable batteries that utilize divalent Mg ions as the charge carrier species can in principle achieve substantially greater volumetric energy densities than conventional Li-ion batteries. One significant impediment to the development of commercially viable Mg-ion batteries is the slow rate of Mg ion diffusion through otherwise promising cathode materials. Accurate prediction of the activation energies associated with this diffusion process using density functional theory (DFT) is especially challenging due to self-interaction errors intrinsic to DFT that lead to over-delocalization of the d-electrons. One effective but highly computationally demanding approach to reducing self-interaction errors is the use of hybrid functionals, which incorporate a fraction of exact Hartree–Fock exchange. In this work, we assess the effects of exact exchange on computed activation energies for ion diffusion in one potential cathode material, α-MoO 3 . In contrast to previous studies that primarily utilize non-hybrid functionals, we perform nudged elastic band calculations in which the nuclear coordinates are fully converged using both hybrid functionals and k-point sampling. Additionally, it is found that while non-hybrid functionals indicate the existence of thermodynamically accessible channels for bulk Mg ion diffusion in all three dimensions, hybrid functionals predict that some of these channels are largely inaccessible under typical charge/discharge conditions. Furthermore, it is demonstrated that certain commonly used approximations for incorporating the effects of Hartree–Fock exchange are inadequate for this system, including DFT+U calculations and the use of single-point hybrid calculations using atomic positions obtained using non-hybrid functionals.

25 ENERGY STORAGE↗