Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “catalyst loading”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Coupled methane and NO x conversion on Pt + Pd/Al 2 O 3 monolith: Conversion enhancement through feed modulation and Mn 0.5 Fe 2.5 O 4 spinel addition

The performance of a dual-layer Pt-Pd/Al 2 O 3 washcoated monolith promoted by an Al 2 O 3 -supported Mn 0.5 Fe 2.5 O 4 spinel base layer was evaluated with the objective to develop a catalyst with a lower loading of Platinum group metal (PGM) for stoichiometric natural gas vehicle (NGV) emission control. Flow reactor results show that a combination of a lean/rich modulated feed and spinel addition gives enhanced methane and NO conversions compared to a steady-state feed having the same overall composition. Washcoated catalysts – PGM-only, spinel-only, PGM + spinel – were compared over a wide range of operating conditions. The results show a decrease in the methane conversion light-off temperature of up to 85 °C for an application-relevant feed (CH 4 + NO + H 2 + CO + O 2 + H 2 O + CO 2 ) while a moderate 40 °C decrease was observed for a simple feed (CH 4 + O 2 + H 2 O + CO 2 ). In the absence of spinel the modulation enhancement is negatively impacted at high methane conversion (> 80 %). The data show that the O 2 storage and release property of the spinel is needed to fully exploit the modulation enhancement. The mechanism responsible for the enhancement is linked to suppression of O 2 inhibition on the methane oxidation rate near the stoichiometric neutral point (λ = 1). Sufficiently fast cycling achieves a balance between a metallic and oxidic precious metal crystallites favorable for methane activation. The addition of spinel moves this balance closer to the λ = 1 feed, enabling a high oxidation efficiency with lower byproduct NH 3 selectivity. Enhancement in the NO conversion follows the methane conversion due to an easier NO reduction under the slightly rich of stoichiometric feed. Comparison of the PGM + spinel catalysts to PGM-only catalysts shows that the addition of spinel in combination with modulation can achieve the same activity with a lower PGM loading.

03 NATURAL GAS↗
DOE OSTI2022

Solar reduction of carbon dioxide on copper-tin electrocatalysts with energy conversion efficiency near 20%

Abstract Copper catalysts modified with tin have been demonstrated to be selective for the electroreduction of carbon dioxide to carbon monoxide. However, such catalysts require the precise control of tin loading amount. Here, we develop a copper/tin-oxide catalyst with dominant tin oxide surface being formed via a spontaneous exchange reaction between sputtered tin and copper oxide. Even though the surface of this catalyst is tin-rich, it achieves an excellent performance towards carbon monoxide production in a flow cell. This contrasts with copper/tin-oxide prepared via atomic layer deposition since it yields selectivity towards carbon monoxide only on a copper-rich surface. Mechanism studies reveal that the tin sites on the tin-rich copper/tin-oxide surface achieve a suitable binding with adsorbed carbon monoxide under the presence of copper. Powered by a triple-junction solar cell, the copper/tin-oxide based electrolyzer sets a new benchmark solar-to-chemical energy conversion efficiency of 19.9 percent with a Faradaic efficiency of 98.9 percent towards carbon monoxide under simulated standard air mass 1.5 global illumination.

14 SOLAR ENERGY↗
DOE OSTI2021

Platinum Deposited Nitrogen-Doped Vertically Aligned Carbon Nanofibers as Methanol Tolerant Catalyst for Oxygen Reduction Reaction with Improved Durability

Nitrogen doping in carbon materials can modify the employed carbon material’s electronic and structural properties, which helps in creating a stronger metal-support interaction. In this study, the role of nitrogen doping in improving the durability of Pt catalysts supported on a three-dimensional vertically aligned carbon nanofiber (VACNF) array towards oxygen reduction reaction (ORR) was explored. The nitrogen moieties present in the N-VACNF enhanced the metal-support interaction and contributed to a reduction in the Pt particle size from 3.1 nm to 2.3 nm. The Pt/N-VACNF catalyst showed better durability when compared to Pt/VACNF and Pt/C catalysts with similar Pt loading. DFT calculations validated the increase in the durability of the Pt NPs with an increase in pyridinic N and corroborated the molecular ORR pathway for Pt/N-VACNF. Moreover, the Pt/N-VACNF catalyst was found to have excellent tolerance towards methanol crossover.

Elangovan, Ayyappan↗
DOE OSTI2022

MoS 2 nanosheet integrated electrodes with engineered 1T-2H phases and defects for efficient hydrogen production in practical PEM electrolysis

Low electrical conductivity and poor accessibility of MoS 2 reaction sites raise great challenges in maximizing the triple-phase-boundary (TPB) sites of MoS 2 -based electrodes and minimizing ohmic losses for efficient hydrogen evolution reaction (HER) in practical proton exchange membrane (PEM) water electrolysis. Herein, we report a scalable hydrothermal approach to fabricate ionomer-free integrated electrodes with engineered 1 T-2 H heterophase and defect-rich MoS 2 nanosheets (MoS 2 NSs) in-situ grown onto the carbon fiber paper (CFP). With an ultralow loading of 0.14 mg/cm 2 , a small voltage of 2.25 V was obtained at 2000 mA/cm 2 in a practical cell with Nafion115 membrane, which outperforms all previously reported high-loading non-precious catalyst-based electrodes. Impressively, it shows 44 times higher mass activity than a high-loading and ionomer-mixed MoS 2 assemblies electrode. Furthermore, this work builds a bridge from catalyst optimization to electrode fabrication and provides a promising direction for improving intrinsic catalytic activity, electrode conductivity and stability for practical PEM water electrolysis.

1T-2H heterophase↗
DOE OSTI2026

A Comparative Study of Ethanol Upgrading to Butadiene Over Rare Earth Elements Incorporated in Dealuminated Beta Zeolites

Copper and rare earth element-containing dealuminated Beta zeolites (CuREE/deAlBeta) are promising catalysts for the conversion of ethanol to C 3+ olefins en route to sustainable aviation fuel. Product selectivities over CuREE/deAlBeta depend on the identity of the REE. Here, in this study, a suite of La/deAlBeta catalysts of varied La loading are prepared, and their reactivities, selectivities, and apparent C-C coupling kinetics in the cascade reaction between ethanol and acetaldehyde are reported. Ex situ and in situ titrations to quantify Lewis acidic La sites quantify distinct numbers of sites, suggesting a distribution of site types. Across a series of REE/deAlBeta catalysts (REE = Y, La, Lu, Yb, Gd), the selectivity to secondary products correlates with the pyridine heats of adsorption at REE Lewis acid sites. The turnover frequency (per Lewis acid site) for C–C coupling was similar across the series of REE/deAlBeta catalysts. Y/deAlBeta and La/deAlBeta, which have the most disparate secondary product selectivities, had similar kinetics for C–C coupling. These findings demonstrate the complexity of quantifying active sites in REE/deAlBeta zeolites, and the sensitivity of the selectivity, but not the reactivity for C–C coupling, to the identity of the REE atom in REE/deAlBeta zeolites.

alcohol upgrading↗
DOE OSTI2020

Role of the metal-support interface in the hydrodeoxygenation reaction of phenol

In this paper, the effect of interfacial sites between Pd particles and Nb 2 O 5 species is investigated by testing a series of Pd-Nb 2 O 5 /SiO 2 catalysts with different niobium loadings for the HDO reaction of phenol in the gas phase. Important differences in the selectivity to deoxygenated product were observed depending on the presence of niobium oxide close to Pd particles, which reveals the key role of the type of active phase in the control of reaction steps. It was found that Pd/SiO 2 catalyst promotes hydrogenation pathways, producing cyclohexanone as the major product. For Pd-Nb 2 O 5 /SiO 2 catalyst containing a Nb/Pd molar ratio of 0.5, a sharp increase in the selectivity to benzene is observed (7.5-fold). Increasing the Nb/Pd molar ratio, the formation of benzene is enhanced. The results showed that the Pd-Nb 2 O 5 interface, composed by an oxophilic oxide in the perimeter of the metal particle, is responsible for the activation of the Csingle bondO bond, promoting the deoxygenation reaction.

09 BIOMASS FUELS↗
DOE OSTI2025

Single Metal Atom Catalysts Prepared by Diluted Atomic Layer Deposition

The scalable and facile preparation of single-atom catalysts remains a critical challenge. Here, in this study, we introduce diluted atomic layer deposition (DALD), a unique approach for synthesizing supported metal catalysts with precisely tunable loadings. Unlike conventional metal deposition by ALD which uses pure metal precursors, DALD employs a diluted precursor mixture, combining organometallic precursors with the corresponding free ligand in controlled ratios. The method enables precise control over metal loadings, allowing the synthesis of structures ranging from nanoparticles to isolated single atoms, as exemplified by Ir, Rh, and Pt on high-surface-area γ-Al 2 O 3 . With its inherent simplicity and exceptional efficiency in metal precursor utilization, DALD represents a highly scalable strategy, unlocking opportunities for integrating single-atom catalysts into industrial processes.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Uncovering the active sites and demonstrating stable catalyst for the cost-effective conversion of ethanol to 1-butanol

We report the recent emergence of a robust renewable ethanol industry has provided a sustainable platform molecule toward the production of value-added chemicals and fuels; what is lacking now are viable conversion processes from ethanol that can displace the current production pathways from non-renewable pathways. Here in the work, we demonstrate the highly selective conversion of ethanol to higher alcohols over low copper loaded MgAl mixed oxide catalysts, with 50% improvement in higher alcohol yields over the current state of the art. At these copper concentrations, atomically dispersed Cu +1 were found to be stable even at highly reductive conditions and highly active towards higher alcohol products (e.g. butanol, hexanol) while suppressing side reaction pathways and leading to extended lifetimes of over 150 hours time on stream. Technoeconomic analysis conducted based on these experimental results demonstrate that this catalytic system is cost-competitive with the conventional process. This marks significant progress in the development of Guerbet coupling of ethanol as a viable renewable process and offers a pathway toward sustainable chemical and fuel production.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

High-Platinum-Content Catalysts on Atomically Dispersed and Nitrogen Coordinated Single Manganese Site Carbons for Heavy-Duty Fuel Cells

Fuel cells for heavy-duty vehicles (HDVs) have attracted considerable attention because of their unique scalability, better fuel economy, the less demand for hydrogen refilling infrastructure. However, the potential application requires more stringent fuel cell durability up to 25,000 h. Membrane electrode assemblies (MEAs) made from platinum group metal (PGM) catalyst with relatively high loading 0.3 mgPt cm –2 play a crucial role in ensuring high-power and long-term durability. Integrating fine PGM nanoparticles and robust carbon support with strengthened interactions is critical for improving MEA performance and durability. Herein, a unique atomically dispersed and nitrogen coordinated single Mn site-rich carbon (M–N–C) support was developed for high content (40 wt%) platinum catalysts for the oxygen reduction reaction (ORR) cathode with reduced thickness. Compared with two controls studied in this work (e.g., a porous graphitic carbon-supported Pt and a commercial TKK Pt/C catalysts), the Pt (40 wt%)/Mn–N–C catalyst exhibited much enhanced catalytic activity and stability for the ORR in both aqueous acidic electrolyte and polymer electrolyte-based MEA. Here, we carefully elucidated the—role of the Mn–N–C support in promoting Pt catalyst concerning its high surface area, partially graphitic structure, and nitrogen dopants, providing better Pt nanoparticle dispersion, and strengthened interactions between Pt and carbon. Consequently, the MEA from the Pt (40 wt%)/Mn–N–C catalyst generated a 1.61 A cm –2 at 0.7 V based on HDV conditions (0.2 mgPt cm –2 and 250 kPa air). More importantly, the MEA is highly durable and can retain 1.31 A cm –2 at 0.7 V after 30,000 voltage cycles (~19% loss), surpassing the commercial Pt/C catalyst (loss of ~56%). Therefore, the Mn–N–C carbon-supported Pt catalyst holds a great promise to meet the challenging DOE target (1.07 A cm –2 at 0.7 V after 150,000 cycles) for HDVs.

25 ENERGY STORAGE↗
DOE OSTI2023

Catalysts Prepared from Atomically Dispersed Ce(III) on MgO Rival Bulk Ceria for CO Oxidation

Atomically dispersed cerium catalysts on an inert, crystalline MgO powder support were prepared by using both Ce(III) and Ce(IV) precursors. The materials were used as catalysts for CO oxidation in a once-through flow reactor and characterized by atomic-resolution scanning transmission electron microscopy, X-ray absorption near edge structure spectroscopy, X-ray photoelectron spectroscopy, and temperature-programmed reduction, among other techniques, before and after catalysis. The most active catalysts, formed from the precursor incorporating Ce(III), displayed a performance similar to that reported for bulk ceria under comparable conditions. The catalyst provided stable time-on-stream performance for as long as it was kept on stream, two days, increasing slightly in activity as the atomically dispersed cerium ions were transformed into ceria nanodomains represented as CeO x and having increased reducibility on the MgO support. Furthermore, the results suggest how highly dispersed supported ceria catalysts with low cerium loadings can be prepared and may pave the way to improved efficiencies of cerium utilization in oxidation catalysis.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Mechanocatalytic Hydrogenolysis of the Lignin Model Dimer Benzyl Phenyl Ether over Supported Palladium Catalysts

This work demonstrates the mechanocatalytic hydrogenolysis of the ether bond in the lignin model compound benzyl phenyl ether (BPE) and hardwood lignin isolated by hydrolysis with supercritical water. Pd catalysts with 4 wt % loading on Al 2 O 3 and SiO 2 supports achieve 100% conversion of BPE with a toluene production rate of (2.6–2.9) × 10 –5 mol·min –1 . The formation of palladium hydrides under H 2 gas flow contributes to an increase in the turnover frequency by a factor of up to 300 compared to Ni on silica–alumina. While a near-quantitative toluene yield is obtained, some of the phenolic products remain adsorbed on the catalyst.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Stability of Atomically Dispersed Fe–N–C ORR Catalyst in Polymer Electrolyte Fuel Cell Environment

We have investigated the durability of a platinum group metal (PGM-)free Fe–N–C catalyst in which the Fe sites are atomically dispersed (AD), and found it to be quite stable in standard accelerated stress test (AST) cycles normally used for low-PGM catalysts: a square wave with 0.6 V lower potential limit (LPL)—0.95 V upper potential limit (UPL) with 3-s holds at UPL and LPL in H 2 /N 2 , at 1.5 atm, 80 °C and 100% RH. Considering the metrics normally employed to characterize the durability of the low-PGM catalysts after 30,000 AST cycles, this PGM-free catalyst lost <50% catalyst activity, <50% H 2 /air performance at 0.8 V, and 40 mV at 1.5 A cm -2 . However, it is less stable in H 2 /air, losing ~50% catalyst activity after just 7.5 h of polarization measurements (load cycles). In combined cycles, the majority of the loss in catalyst activity occurred during the load cycles in H 2 /air rather than AST cycles in H 2 /N 2 . We have concluded that, unlike low-PGM catalysts that lose electrochemically active surface area (ECSA) through potential cycling-induced processes, (AD)Fe–N–C catalysts degrade by processes associated with the presence of oxygen.

25 ENERGY STORAGE↗
DOE OSTI2021

High Performance PEFC Electrode Structures

Raytheon Technologies Research Center (RTRC) in collaboration with Ion Power Inc. and the University of Arkansas at Little Rock and the FC-PAD consortium executed a project that: (1) developed comprehensive models of oxygen and proton transport in cathode catalyst layers that provided new insights about losses associated with reducing platinum loading to 0.1 mg/cm 2 , (2) designed, fabricated, characterized, and tested cells featuring carbon-supported catalyst layers with low platinum loadings that met efficiency and power density targets set forth by the Hydrogen and Fuel Cells Technology Office, and (3) designed, fabricated, characterized, and tested novel catalyst structures. The modeling efforts produced eight scientific publications that shared new descriptions of oxygen and proton transport in catalyst layers with the broader technical community. The key physical insights from the models are expressed in straightforward algebraic expressions, facilitating easy adoption by other researchers. The models developed during the project explain why resistance to oxygen transport is inversely proportional to interfacial area of platinum – an observation that eluded quantitative explanation for a decade. The models quantitatively predict polarization when measured morphological parameters and transport properties are input. Membrane-electrode assemblies made during the project met stated goals for current at high voltage and power density at rated voltage for transportation fuel cells at the end of budget period 2. High performance was achieved by developing a diffusion layer with low resistance to oxygen transport and a PtCo/C cathode catalyst layer capable of supporting rapid proton and oxygen transport. The project was subsequently directed to curtail experimental work and focus on modeling during budget period 3. Ion Power Inc. developed new expertise in fabricating catalyst layers containing platinum-cobalt catalysts, and processing very thin membranes. The University of Arkansas at Little Rock developed novel nanocolumnar self-supported thin film electrocatalysts that can be grown on carbon supports using a simple high pressure sputter deposition method. The nanocolumnar microstructure provides adequate surface-to-volume ratio for efficient platinum utilization, and the conformal platinum shell with larger crystal grain sizes covering the carbon support surface may eliminate durability issues associated with catalyst dissolution, agglomeration, and carbon corrosion.

08 HYDROGEN↗
DOE OSTI2023

Performance of Polymer Electrolyte Membrane Water Electrolysis Systems: Configuration, Stack Materials, Turndown and Efficiency

A cell model is developed and validated to analyze the performance of polymer electrolyte membrane water electrolysis (PEMWE) stacks and systems. It is used to characterize the oxygen evolution reaction (OER) activity on a TiO2-supported IrO2 catalyst and an unsupported IrO2 powder catalyst. Electrochemical, stack, and system thermoneutral potentials are defined and determined for isothermal and non-isothermal stack operation. Conditions are determined under which the system thermoneutral potential or flammability of H2 in the O2 anode stream limits the stack turndown and operating temperature. Performance is analyzed of a complete PEMWE system with an electrolyzer stack containing an IrO2/TiO2 anode catalyst (2 mg/cm2 Ir loading) and N117-like membrane mitigated for H2 crossover, anode balance-of-plant (BOP) components, cathode BOP system with temperature swing adsorption for H2 purification, and electrical BOP system with transformer and rectifier. At the rated power condition, defined as 2 A/cm2 at 1.9 V, 80 °C, and 30 bar H2 pressure, the stack/system efficiency is 65.3%/60.3% at beginning of life (BOL), decreasing to 59.3%/53.9% at end of life (EOL). The peak stack/system efficiency is 76.3%/70.2% at BOL, decreasing to 71.2%/65.6% at EOL. Improvements in catalyst activity and membrane are identified for a 50% increase in current to 3 A/cm2 at 1.8 V.

36 MATERIALS SCIENCE↗
NASA NTRS2018

Current Activities in the Advanced Exploration Systems ISRU Project

Media Filter MOXIE support: completed flow performance tests and initial dust loading tests of the MOXIE HEPA filter in the Mars Flow Loop Designed and fabricated prototype full-scale scroll filter for testing of renewable filter performance Mars Flow Loop upgrades: installed more sensitive instrumentation, improved imaging, and increased run duration capability Electrostatic Precipitator (ESP) Plasma-physics based model predicts particle charge and trajectory Characterizing dust environment from fluidized-bed injection dust environment using laser sheet visualization and Fine Particle Analyzer Sabatier Design Study Defined the Sabatier design space, including reactor type, thermal management, gas recycling/separation Modeled Sabatier systems with one or two reactors with different types of thermal management Adding thermal management schemes and recycling and gas separation to model Catalyst Screening Performing compression testing on new and used catalyst pellets Performing vibration testing on different catalyst pellet types under different load conditions Preparing to test catalysts for performance and degradation

In-Situ Resource Utilization↗
DOE OSTI2020

Probing Membrane Degradation with Varying Catalyst Layer Thickness and Carbon Support

Understanding membrane degradation continues to be of significant importance when studying fuel cell durability. Fuel cell performance and durability depends heavily on the membrane's chemical and mechanical integrity. In Nafion® membranes, hydroxyl radicals are the primary cause of chemical membrane degradation as they attack the membrane's polymer structure. Radical formation can ensue via peroxide decomposition at the cathode or gases reacting on Pt particles within the membrane. Here, a previous research effort on membrane degradation as a function of ultra-low Pt loadings (≤ 0.1 mgPt cm -2 ) showed the degradation rate increases with Pt loading. This is most likely due to more heterogenous sites for radical formation. Manufacturing MEAs with ultra-low Pt loadings can yield thin, non-uniform catalyst layers. In this research effort we studied membrane degradation with ultra-low Pt loadings while varying catalyst layer thickness, I/C ratio, and types of carbon support.

25 ENERGY STORAGE↗
DOE OSTI2024

Development of a Sulfur Tolerant CHG Process (CRADA 442) (Final Report)

The Pacific Northwest Laboratory (PNNL) has developed the Catalytic Hydrothermal Gasification (CHG) technology, which can convert low-value organics dispersed in aqueous streams, such as the aqueous phase byproduct from hydrothermal liquefaction (HTL) of wet wastes, to a mixture of methane, H 2 , and CO 2 . The current CHG catalyst, ruthenium (Ru) on a graphite substrate, was selected for its effectiveness as a reducing catalyst. However, the target waste aqueous feedstock, the HTL aqueous phase from wet wastes, such as sewage sludge, contains a fair amount of sulfur in both organic and inorganic forms. Like many other reduced metal catalysts, Ru is deactivated or poisoned by exposure to sulfur, among other contaminants. In general, a deactivated Ru catalyst cannot be reactivated or restored except by removing and returning it for remanufacturing. Therefore, there is an urgent need for a sulfur-resistant catalyst to enable CHG processing of the HTL aqueous waste stream. PNNL, with support from SoCalGas CRADA, has developed a sulfur resistant CHG catalyst and demonstrated a stable CHG process for converting HTL aqueous phases from wet wastes. Here, we report the major accomplishments of the project: • We have demonstrated that sulfided Ru based catalysts is stable during CHG of HTL aqueous waste stream, with a requirement of activity improvement. • We have developed a new catalyst, with 0.5-2 wt.% Ru loading, showing better activity compared to the baseline 6.7 wt.% RuSx/C catalyst. • With the new catalysts, the single-pass COD reduction is approximately 60% and two-pass COD reduction can reach approximately 85%. • The process is robust in terms of being effective across a wide range of organic species in the feedstock. • Techno-economic analysis was conducted to evaluate the economic impact of catalyst advancement and identify further improvement requirements. This type of catalyst shows great potential to be efficient and robust for CHG with low catalyst cost.

03 NATURAL GAS↗