Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “boron carbide”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS2017

Effect of Mechanical and Thermal Loading Histories on Residual Properties of SiCf/SiC Ceramic Matrix Composites

Silicon Carbide based Ceramic Matrix Composites (CMCs) are attractive materials for use in high-temperature structural applications in the aerospace and nuclear industries. Under high stresses and temperatures, creep degradation is the dominant damage mechanism in CMCs. Consequently, chemical vapor infiltration (CVI) SiCf/SiC ceramic matrix composites (CMC) incorporating SylramicTM-iBN SiC fibers coated with boron nitride (BN) interphase and CVI-SiC matrix were tested to examine creep behavior in air at a range of elevated temperatures of (2200 - 2700 F). Samples that survived creep tests were evaluated via RT fast fracture tensile tests to determine residual properties, with the use of acoustic emission (AE) to assess stress dependent damage initiation and progression. Microscopy of regions within the gage section of the tested specimens was performed. Observed material degradation mechanisms are discussed.

creep↗
NASA NTRS1998

Tensile Properties and Microstructural Characterization of Hi-Nicalon SiC/RBSN Composites

The room temperature physical and mechanical properties of silicon carbide fiber-reinforced reaction-bonded silicon nitride matrix composites (SiC/RBSN) were measured, and the composite microstructure was analyzed. The composites consist of nearly 24 vol% of aligned Hi-Nicalon SiC fiber yarns in a approx. 30 vol% porous silicon nitride matrix. The fiber yarns were coated by chemical vapor deposition with a 0.8 mm layer of boron nitride (BN) followed by a 0.2 mm layer of SiC. In the as-fabricated condition, both 1-D and 2-D composites exhibited high strength and graceful failure, and showed improved properties w en compared with unreinforced matrix of comparable density. No indication of reaction between the SiC fiber and BN coating was noticed, but the outer SiC layer reacted locally with the nitridation enhancing additive in the RBSN matrix. A comparison is made between the predicted and measured values of matrix cracking strength.

Bhatt, Ramakrishna T.↗
NASA NTRS1998

Tensile Properties and Microstructural Characterization of Hi-Nicalon SiC/RBSN Composites

The room temperature physical and mechanical properties of silicon carbide fiber-reinforced reaction-bonded silicon nitride matrix composites (SiC/RBSN) were measured, and the composite microstructure was analyzed. The composites consist of nearly 24 vol% of aligned Hi-Nicalon SiC fiber yarns in a approx. 30 vo1% porous silicon nitride matrix. The fiber yarns were coated by chemical vapor deposition with a 0.8 micron layer of boron nitride (BN) followed by a 0.2 micron layer of SiC. In the as-fabricated condition, both 1-D and 2-D composites exhibited high strength and graceful failure, and showed improved properties when compared with unreinforced matrix of comparable density. No indication of reaction between the SiC fiber and BN coating was noticed, but the outer SiC layer reacted locally with the nitridation enhancing additive in the RBSN matrix. A comparison is made between the predicted and measured values of matrix cracking strength.

Bhatt, Ramakrishna T.↗
DOE OSTI2026

Water Vapor Resistant SiC/SiC Composite for Hydrogen-Based Turbines (Final Scientific Technical Report)

New material innovations are needed for the extreme environments of next generation, hydrogen-fueled turbine engines. Ceramic matrix composites (CMCs) offer high-temperature capability but are susceptible to degradation in high-temperature water vapor. Pratt & Whitney’s (P&W) baseline silicon carbide (SiC)/SiC CMC was initially applied to design a component in a hydrogen-fueled engine, verifying the existence of a design space and extracting boundary conditions to inform testing parameters. Several material innovations, including two fibers, interface coatings (IFC), and self-healing matrices (SHM), were investigated to improve high-temperature performance in water vapor. A boron-doped pyrocarbon (B-PyC) IFC and a SHM matrix with layers of zirconium nitride (ZrN) or zirconium diboride (ZrB 2 ) were developed to fabricate minicomposites with either standard Hi-Nicalon™ Type S (HNS) fibers or new Tyranno® SA4 fibers (SA4). The B-PyC IFC is functional but lacks in providing improved durability. A matrix consisting of thick layers of SiC and thin layers of ZrB 2 shows promise as a SHM that can effectively seal matrix cracks in this extreme environment. Minicomposites with HNS fibers generally outperform those with SA4 fibers.

08 HYDROGEN↗
NASA NTRS2000

Corrosion Issues for Ceramics in Gas Turbines

The requirements for hot-gas-path materials in gas turbine engines are demanding. These materials must maintain high strength and creep resistance in a particularly aggressive environment. A typical gas turbine environment involves high temperatures, rapid gas flow rates, high pressures, and a complex mixture of aggressive gases. Figure 26.1 illustrates the requirements for components of an aircraft engine and critical issues [1]. Currently, heat engines are constructed of metal alloys, which meet these requirements within strict temperature limits. In order to extend these temperature limits, ceramic materials have been considered as potential engine materials, due to their high melting points and stability at high temperatures. These materials include oxides, carbides, borides, and nitrides. Interest in using these materials in engines appears to have begun in the 1940s with BeO-based porcelains [2]. During the 1950s, the efforts shifted to cermets. These were carbide-based materials intended to exploit the best properties of metals and ceramics. During the 1960s and 1970s, the silicon-based ceramics silicon carbide (SiC) and silicon nitride (Si3N4) were extensively developed. Although the desirable high-temperature properties of SiC and Si3N4 had long been known, consolidation of powders into component-sized bodies required the development of a series of specialized processing routes [3]. For SiC, the major consolidation routes are reaction bonding, hot-pressing, and sintering. The use of boron and carbon as additives which enable sintering was a particularly noteworthy advance [4]. For Si3N4 the major consolidation routes are reaction bonding and hot pressing [5]. Reaction-bonding involves nitridation of silicon powder. Hot pressing involves addition of various refractory oxides, such as magnesia (MgO), alumina (Al2O3), and yttria (y2O3). Variations on these processes include a number of routes including Hot Isostatic Pressing (HIP), gas-pressure sintering, sinter-HIPing, and Encapsulation-HIPing. It is important to note that each process involves the addition of secondary elements, which later were shown to dramatically influence oxidation and corrosion behavior. As dense bodies of silicon-based ceramics became more readily available, their desirable high temperature properties were confirmed. These materials retained strength to very high temperatures (i.e. 1300-1400 C). Further, they were lightweight and made from abundant materials. SiC and Si3N4 therefore emerged as leading ceramic candidates for components in heat engines, designed to operate at higher temperatures for better performance and fuel efficiency. The first US programs for ceramics in heat engines have been reviewed [6]. Selected programs on ceramic engine parts are summarized here in regard to their contributions to understanding the corrosion behavior of a heat engine environment.

Jacobson, Nathan S.↗
DOE OSTI2020

In situ characterization of residual stress evolution during heat treatment of SiC/SiC ceramic matrix composites using high-energy X-ray diffraction

Volumetric strains were measured in silicon carbide/silicon carbide melt-infiltrated ceramic matrix composites (CMCs) at ambient and high temperatures using high-energy synchrotron X-ray diffraction (XRD). Both silicon and silicon carbide constituents were interrogated utilizing a broad spectrum of diffracting planes that would be largely inaccessible to common laboratory XRD equipment. Residual room-temperature principal strains in the melt-infiltrated silicon phase were found to be approximately 1100 mu epsilon in compression, corresponding to stresses of approximately 300 MPa using simplifying constitutive assumptions. Residual room-temperature principal strains in silicon carbide particles found throughout the matrix were approximately 500 mu epsilon in tension, corresponding to approximately 300 MPa. Residual strains were found to decrease considerably as temperatures increased from ambient temperature to 1250 degrees C. Additionally, residual strains returned to approximately preheat treatment values after cool-down to ambient temperature. Strain measurements in the silicon phase were found to be significantly affected by dissolved boron dopant levels causing contraction of the silicon lattice. This contraction must be accounted for in high-temperature experiments for accurate calculation of stresses in the silicon phase.

36 MATERIALS SCIENCE↗
NASA NTRS1986

Solar silicon from directional solidification of MG silicon produced via the silicon carbide route

A process of metallurgical grade (MG) silicon production is presented which appears particularly suitable for photovoltaic (PV) applications. The MG silicon is prepared in a 240 KVA, three electrode submerged arc furnace, starting from high grade quartz and high purity silicon carbide. The silicon smelted from the arc furnace was shown to be sufficiently pure to be directionally solidified to 10 to 15 kg. After grinding and acid leaching, had a material yield larger than 90%. With a MG silicon feedstock containing 3 ppmw B, 290 ppmw Fe, 190 ppmw Ti, and 170 ppmw Al, blended with 50% of off grade electronic grade (EG) silicon to reconduct the boron content to a concentration acceptable for solar cell fabrication, the 99% of deep level impurities were concentrated in the last 5% of the ingot. Quite remarkably this material has OCV values higher tham 540 mV and no appreciable shorts due to SiC particles.

Rustioni, M.↗
NASA NTRS2018

Modeling of Time-Dependent Strength Degradation of SiC/SiC Ceramic Matrix Composites via MAC/GMC Computer Code

Silicon carbide fiber reinforced silicon carbide (SiC/SiC) ceramic matrix composites (CMCs) display time-dependent strength degradation at intermediate temperatures (600 to 900 degrees Centigrade). This is generally believed to be an oxidation induced phenomenon. The understanding of the effect of temperature with environment (oxidation) is key towards development of SiC/SiC CMCs with a reliable load carrying capacity. Various theories have been proposed to explain the strength degradation. One suggests that the boron nitride (BN) coating deposited on the fibers oxidizes causing fusion of fibers. Another theory proposes that the SiC fibers are oxidized forming a silica scale leading to premature fiber failure. A more recent theory suggests that SiC fiber strength is intrinsically time-dependent due to slow crack growth of flaws in the fibers. An empirical model, termed as a "fiber classic model," which is based on a standard slow crack growth type power-law, has been implemented within NASA's micromechanics-based MAC/GMC computer code as a user routine. Model parameters for this "classic model" were calibrated from stress-rupture data of Hi-Nicalon (TM) monofilaments using the maximum likelihood estimation (MLE) technique. This new capability in the MAC/GMC computer code was then used to predict the stress-rupture behavior of Hi-Nicalon (TM) tows as well as 2-D SiC/SiC composites reinforced with Hi-Nicalon (TM) fibers. Results demonstrate that the MAC/GMC with this new capability successfully predicts the time-to-failure vs. applied stress within the intermediate temperature range at various scales as well as laminated composites in an oxidizing environment.

Environmental degradation↗
NASA NTRS1997

Environmental Effects on Non-oxide Ceramics

Non-oxide ceramics such as silicon carbide (SiC) and silicon nitride (Si3N4) are promising materials for a wide range of high temperature applications. These include such diverse applications as components for heat engines, high temperature electronics, and re-entry shields for space vehicles. Table I lists a number of selected applications. Most of the emphasis here will be on SiC and Si3N4. Where appropriate, other non-oxide materials such as aluminum nitride (AlN) and boron nitride (BN) will be discussed. Proposed materials include both monolithic ceramics and composites. Composites are treated in more detail elsewhere in this volume, however, many of the oxidation/corrosion reactions discussed here can be extended to composites. In application these materials will be exposed to a wide variety of environments. Table I also lists reactive components of these environments.It is well-known that SiC and Si3N4 retain their strength to high temperatures. Thus these materials have been proposed for a variety of hot-gas-path components in combustion applications. These include heat exchanger tubes, combustor liners, and porous filters for coal combustion products. All combustion gases contain CO2, CO, H2, H2O, O2, and N2. The exact gas composition is dependent on the fuel to air ratio or equivalence ratio. (Equivalence ratio (EQ) is a fuel-to-air ratio, with total hydrocarbon content normalized to the amount of O2 and defined by EQ=1 for complete combustion to CO2 and H2O). Figure 1 is a plot of equilibrium gas composition vs. equivalence ratio. Note that as a general rule, all combustion atmospheres are about 10% water vapor and 10% CO2. The amounts of CO, H2, and O2 are highly dependent on equivalence ratio.

Jacobson, Nathan S.↗
DOE OSTI2025

Advanced polymer impregnation and pyrolysis (PIP) of SiOC-based ceramic matrix composites (CMCs)

Silicon carbide (SiC) ceramic matrix composites (CMCs) are valued for their high-temperature properties, making them ideal for harsh environments. However, conventional polymer impregnation and pyrolysis (C-PIP) often result in porous composites and require numerous cycles for densification. This study introduces the advanced PIP (A-PIP) method using a crosslinked polycarbosiloxane (PCS) precursor to enhance densification efficiency. Five SiC CMCs were fabricated using C-PIP and A-PIP, with variations in fiber reinforcement and fiber coatings. A-PIP achieved up to 19 % higher density and 78 % lower porosity in 79–86 % less processing time compared to C-PIP. Moreover, SiC-SiOC composites with boron nitride-coated fibers showed significant improvements in tensile strength (11 MPa to 134 MPa) and strain at maximum strength (0.01–0.11 %), underscoring the role of weak fiber-matrix interfaces. In conclusion, these results demonstrate A-PIP's potential to produce dense, low-porosity SiC CMCs more efficiently, significantly reducing manufacturing time and costs.

36 MATERIALS SCIENCE↗
NASA NTRS1996

Dopant Incorporation Efficiency in CVD Silicon Carbide Epilayers

In order to ensure reproducible and reliable SiC semiconductor device characteristics, controlled dopant incorporation must be accomplished. Some of the many factors which greatly influence dopant incorporation are the site-competition effect, SiC(0001) substrate polarity, substrate temperature, and the dopant-source reactor concentration. In this paper, dopant incorporation is considered and compared for various dopants in the context of dopant incorporation efficiency. By using secondary ion mass spectrometry (SIMS), the relative dopant incorporation efficiencies were calculated by dividing the SIMS determined dopant concentration in the resulting epitaxial layer by the intentional gas phase dopant concentration used during the SiC CVD. Specifically, the relative magnitudes of dopant incorporation efficiencies for nitrogen, phosphorus, and boron in 6H-SiC (0001) Si-face epitaxial layers are compared as a function of the site-competition effect and the dopant-source reactor concentrations. This serves as a first approximation for comparison of the relative 'doping potencies' of some common dopants used in SiC CVD epitaxial growth.

Larkin, D. J.↗
DOE OSTI2023

Variations in Creep Performance of P92 Steel Within Its Composition Range: Influence of N Solubility

Underspecified composition ranges often lead to alloys with unpredictable mechanical performance. To better understand the changes in microstructure and mechanical performance associated with variations of key elements, three versions of P92 are formulated within, or close to, the specified allowable for N, B, and C ranges. Chromium and Si are also varied to influence N solubility. Different service conditions (i.e., temperature and stress) are explored. It is observed that >80% decrease in creep life occurs at 625 °C and 155 MPa for the highest B and N containing alloy. Multiscale characterization reveals key changes due to the trace element variation. The high B and N containing alloy forms deleterious BN precipitates with morphology that promotes crack nucleation and damage accumulation, but this alloy additionally forms higher fractions of beneficial MX precipitates. The alloy with the lowest B and N concentrations but greater C content shows the best creep performance—a consequence of the refined M 23 C 6 carbide precipitate population and the absence of large-scale inclusions or BN precipitates. Calculations of creep activation energy reveal that the high B and N containing alloy is more prone to damage accumulation which causes an early onset of accelerating creep and greater minimum creep rate.

36 MATERIALS SCIENCE↗
NASA NTRS1989

Improved silicon carbide for advanced heat engines

The development of high strength, high reliability silicon carbide parts with complex shapes suitable for use in advanced heat engines is studied. Injection molding was the forming method selected for the program because it is capable of forming complex parts adaptable for mass production on an economically sound basis. The goals were to reach a Weibull characteristic strength of 550 MPa (80 ksi) and a Weibull modulus of 16 for bars tested in four-point loading. Statistically designed experiments were performed throughout the program and a fluid mixing process employing an attritor mixer was developed. Compositional improvements in the amounts and sources of boron and carbon used and a pressureless sintering cycle were developed which provided samples of about 99 percent of theoretical density. Strengths were found to improve significantly by annealing in air. Strengths in excess of 550 MPa (80 ksi) with Weibull modulus of about 9 were obtained. Further improvements in Weibull modulus to about 16 were realized by proof testing. This is an increase of 86 percent in strength and 100 percent in Weibull modulus over the baseline data generated at the beginning of the program. Molding yields were improved and flaw distributions were observed to follow a Poisson process. Magic angle spinning nuclear magnetic resonance spectra were found to be useful in characterizing the SiC powder and the sintered samples. Turbocharger rotors were molded and examined as an indication of the moldability of the mixes which were developed in this program.

Whalen, Thomas J.↗
NASA NTRS1974

Low-cost methods for fabrication of aluminum-boron shapes

Deformation processing has not been seriously considered as applicable to composite fabrication, particularly if the filament (e.g., boron) lacks plasticity. When, however, the brittle filament is clad with a ductile matrix such as 6061 Al, the underlying filament is protected from damage even when cold worked severely as in drawing and rolling. These two metal-working processes have been applied successfully to produce seven ply aluminum 50 vol % boron tubes up to 2 in. O.D. by 3 feet in length and flats 1 in. in width by 2 feet in length respectively. Although adequate densification is achieved via drawing and rolling, the former has been given major emphasis. Mechanical properties of rolled and drawn flats and tubes compare favorably with those prepared by static methods. However, the objective of the presentation is to focus on lower processing costs. In specific terms, 2 in. tubes in lengths up to 12 feet can be produced for as little as $150/lb. This is possible only because standard drawbench and carbide dies can be utilized. Furthermore, the major steps including cladding, preform preparation and drawing are conducive to automation.

Divecha, A. P.↗
DOE OSTI2026

SiC Substrate Composition Effect on TGO Scale Growth in EBC Systems During High‐Temperature Steam Exposure

A systematic investigation was conducted on the oxidation behavior of silicon-bond coats within environmental barrier coating (EBC) systems applied to Si-carbide (SiC) substrates, aiming to understand how different underlying SiC substrates influence the bond coat's thermally grown oxide (TGO) and its properties. The study examined (Y/Yb) 2 Si 2 O 7 /Si coatings on three cost-effective surrogate SiC substrates (chemical vapor deposition [CVD]-grown β-SiC, sintered α-SiC, and reaction-bonded [RB] SiC) for SiC fiber /SiC matrix ceramic matrix composites (CMCs). Discrepancies in TGO growth were observed, with noticeably higher growth rates reported for the coated CMC specimens than for the four monolithic SiC specimens. The CMC samples produce an amorphous TGO, whereas the other monolithic substrates formed a crystalline TGO, which lowered the oxygen permeability through the SiO 2 scale. In conclusion, the vitrification of the TGO in the (Y/Yb) 2 Si 2 O 7 /Si/CMC system resulted from the migration of boron species from the CMC substrate to the SiO 2 scale, leading to network modification via boron doping.

EBC↗
NASA NTRS1984

Processing of sintered alpha SiC

Processing methods of sintered alpha SiC for engine applications are developed in a cost effective manner, using a submicron sized powder blended with sintering aids (boron and carbon). The processes for forming a green powder compact, such as dry pressing, cold isostatic pressing and green machining, slip casting, aqueous extrusion, plastic extrusion, and injection molding, are described. Dry pressing is the simplest route to component fabrication, and is carried out at approximately 10,000 psi pressure, while in the cold isostatic method the pressure could go as high as 20,000 psi. Surfactants are added to control settling rates and casting characteristics in the slip casting. The aqueous extrusion process is accomplished by a hydraulic ram forcing the aqueous mixture through a die. The plastic forming processes of extrusion and injection molding offer the potential of greater diversity in shape capacity. The physical properties of sintered alpha SiC (hardness, Young's modulus, shear modulus, and thermal diffusivity) are extensively tested. Corrosion resistance test results of silicon carbide are included.

Storm, R. S.↗
NASA NTRS2002

Ceramic Composite Intermediate Temperature Stress-Rupture Properties Improved Significantly

Silicon carbide (SiC) composites are considered to be potential materials for future aircraft engine parts such as combustor liners. It is envisioned that on the hot side (inner surface) of the combustor liner, composites will have to withstand temperatures in excess of 1200 C for thousands of hours in oxidizing environments. This is a severe condition; however, an equally severe, if not more detrimental, condition exists on the cold side (outer surface) of the combustor liner. Here, the temperatures are expected to be on the order of 800 to 1000 C under high tensile stress because of thermal gradients and attachment of the combustor liner to the engine frame (the hot side will be under compressive stress, a less severe stress-state for ceramics). Since these composites are not oxides, they oxidize. The worst form of oxidation for strength reduction occurs at these intermediate temperatures, where the boron nitride (BN) interphase oxidizes first, which causes the formation of a glass layer that strongly bonds the fibers to the matrix. When the fibers strongly bond to the matrix or to one another, the composite loses toughness and strength and becomes brittle. To increase the intermediate temperature stress-rupture properties, researchers must modify the BN interphase. With the support of the Ultra-Efficient Engine Technology (UEET) Program, significant improvements were made as state-of-the-art SiC/SiC composites were developed during the Enabling Propulsion Materials (EPM) program. Three approaches were found to improve the intermediate-temperature stress-rupture properties: fiber-spreading, high-temperature silicon- (Si) doped boron nitride (BN), and outside-debonding BN.

Morscher, Gregory N.↗
NASA NTRS1997

Computational Modeling in Structural Materials Processing

High temperature materials such as silicon carbide, a variety of nitrides, and ceramic matrix composites find use in aerospace, automotive, machine tool industries and in high speed civil transport applications. Chemical vapor deposition (CVD) is widely used in processing such structural materials. Variations of CVD include deposition on substrates, coating of fibers, inside cavities and on complex objects, and infiltration within preforms called chemical vapor infiltration (CVI). Our current knowledge of the process mechanisms, ability to optimize processes, and scale-up for large scale manufacturing is limited. In this regard, computational modeling of the processes is valuable since a validated model can be used as a design tool. The effort is similar to traditional chemically reacting flow modeling with emphasis on multicomponent diffusion, thermal diffusion, large sets of homogeneous reactions, and surface chemistry. In the case of CVI, models for pore infiltration are needed. In the present talk, examples of SiC nitride, and Boron deposition from the author's past work will be used to illustrate the utility of computational process modeling.

Meyyappan, Meyya↗