Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “batch size”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

265 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS2015

A Particle Batch Smoother Approach to Snow Water Equivalent Estimation

This paper presents a newly proposed data assimilation method for historical snow water equivalent SWE estimation using remotely sensed fractional snow-covered area fSCA. The newly proposed approach consists of a particle batch smoother (PBS), which is compared to a previously applied Kalman-based ensemble batch smoother (EnBS) approach. The methods were applied over the 27-yr Landsat 5 record at snow pillow and snow course in situ verification sites in the American River basin in the Sierra Nevada (United States). This basin is more densely vegetated and thus more challenging for SWE estimation than the previous applications of the EnBS. Both data assimilation methods provided significant improvement over the prior (modeling only) estimates, with both able to significantly reduce prior SWE biases. The prior RMSE values at the snow pillow and snow course sites were reduced by 68%-82% and 60%-68%, respectively, when applying the data assimilation methods. This result is encouraging for a basin like the American where the moderate to high forest cover will necessarily obscure more of the snow-covered ground surface than in previously examined, less-vegetated basins. The PBS generally outperformed the EnBS: for snow pillows the PBSRMSE was approx.54%of that seen in the EnBS, while for snow courses the PBSRMSE was approx.79%of the EnBS. Sensitivity tests show relative insensitivity for both the PBS and EnBS results to ensemble size and fSCA measurement error, but a higher sensitivity for the EnBS to the mean prior precipitation input, especially in the case where significant prior biases exist.

EnBS↗
DOE OSTI2025

THE DESIGN OF RADIAL HONEYCOMB LATTICES FOR IMPACT ENERGY ABSORPTION IN RADIOACTIVE MATERIALS PACKAGES

In this research we present a variation on the corrugation technique of honeycomb lattices, for cylindrical honeycombs, making them much easier to design for impact energy absorption in radioactive materials packages. This variation, termed radial honeycomb lattices, eliminates the residual strain and saddle effect. The use of honeycomb lattices provides advantages over the typically used foams. While foams are effective at absorbing impact energy, they can burn, their material properties are difficult to control, they can degrade over time, and procurement of raw materials can be dependent on timing of manufacturer batch runs. While the weaknesses of foam are strengths for honeycomb lattices, lattices have a different set of problems. Typically, when cylindrical honeycomb lattices are manufactured, they are manufactured flat, wrapped around a mandrel of the desired radius, and then brazed. This approach introduces residual strains, resulting in the saddle effect, which limits both the radial thickness and cylinder length. The radial honeycomb lattice approach presented here makes the design of thicker and longer cylinder honeycombs possible. To address these issues, we propose a honeycomb lattice which changes in cross-section from the inner to the outer radius of the cylinder. This causes the lattice to automatically wrap into a cylinder as it exits the corrugating gears. The theoretically bounding case, of a square cross-section at the inner radius, transitioning through a hexagon, to a diamond cross-section at the outer radius, results in a maximum thickness of approximately 41% of the inner radius. Full mathematical derivations, implemented in computer code, allow for the design of an entire radial honeycomb lattice, including the corrugating gears. To accomplish this only the radial thickness, inner cross-section shape, cell size, and nominal gear radius need to be specified, making the design of these lattices very efficient. Radial honeycomb lattice prototypes have demonstrated that the honeycomb does indeed wrap into a cylinder as intended, without the saddle effect, and can therefore be used to create thick-walled cylinders of any length. These design improvements make cylindrical honeycomb lattices much more accessible as a design element for radioactive materials packages

Johnson, William R. [Savannah River National Labor↗
DOE OSTI2021

AGR-5/6/7 Fuel Fabrication Report

The U.S. Department of Energy Office of Nuclear Energy (DOE NE) and the Idaho National Laboratory (INL) Advanced Reactor Technologies (ART) Advanced Gas Reactor (AGR) Fuel Development and Qualification program (referred to as AGR Fuel program hereafter) are pursuing qualification of tristructural isotropic (TRISO) coated particle fuel for use in high temperature gas cooled reactors (HTGRs). The AGR Fuel program was established to provide a fuel qualification data set in support of the licensing and operation of an HTGR. BWX Technologies Nuclear Operations Group (BWXT-NOG) was subcontracted to fabricate the fuel for the AGR program. Several investments and innovations were realized in preparation to fabricate fuel for the AGR-5/6/7 irradiation experiments that brought fuel fabrication fully out of the laboratory and into engineering-scale operations. These included: • Increased the kernel fabrication line capacity and uniformity • Upgraded ancillary support equipment and processes for the tristructural isotropic (TRISO) coating furnace • Demonstrated efficient production of the matrix precursor powder by dry jet milling of co mingled components • Demonstrated an engineering-scale method for quick and efficient overcoating TRISO particles with the matrix precursor • Demonstrated an automated, multi cavity compacting system with a volumetric feed system • Demonstrated a combined-cycle thermal treatment furnace These changes increased production rates of some of these processes by an order of magnitude or more while eliminating the use of flammable solvents, multiple grinding and sorting operations, and the weighing out of individual die charges. Three fuel kernel lots were fabricated for production of the fuel for AGR-5/6/7. The initial lot (J52R-16-39316) was certified to fuel specifications but was not used because the kernels had a high fraction of internal fissures that caused an unacceptable fraction of the kernels to fragment when charged to the coating furnace where the TRISO coating would be deposited. Fragmented kernels increased the dispersed uranium in the particles and produced a worrisome fraction of dimpled particles with an elevated probability of in-pile failure. After some efforts to identify the cause of the fissure formation, two additional lots were produced with much lower fissure fractions, J52R-16-69317 and 69318. The latter kernel lot was a backup to the first and was not needed. Multiple kernel batches were composited to form each of the lots so as to simulate a commercial-scale operation where kernel batches would also be composited. Multiple TRISO coating runs were performed and the product characterized so that several could be composited into a TRISO lot. TRISO lot J52R-16-98005 conformed to all fuel specifications except the mean outer pyrocarbon (OPyC) layer thickness was thinner than specified. Furthermore, it was determined that the TRISO lot had a dispersed uranium fraction (DUF) that might result in the compacts not meeting the DUF specification. A review of the role of the OPyC layer and consequences of the DUF by the Technical Coordination Team and INL concluded that the fuel was acceptable for use in the AGR-5/6/7 irradiation experiment. The TRISO particles were overcoated with the matrix precursor that had been produced in a jet-milling operation. The overcoating was performed in equipment originally designed to coat pharmaceuticals. The overcoating process performed well; producing highly spherical and uniform overcoats requiring little upgrading and no recycle or rework. TRISO particles were overcoated with the matrix precursor to achieve nominal volumetric packing fractions (PFs) of TRISO particles of 25% and 40% for the irradiation experiments. The 40% PF compacts occupy the first and fifth test capsule in the test train while the inner three capsules are loaded with 25% PF compacts. The resinated graphite matrix precursor powder was a derivative of the German A3-27 matrix formulation, which differs from previous AGR irradiation campaigns that used an A3-3 formulation. Jet milling of the matrix powder precursor produced a finer mean graphite particle size than the milling operations used for the A3-3 matrix powder precursor. Changes made in the matrix formula and equipment yielded compacts with significantly higher matrix density than was attained in previous AGR irradiation campaigns. The changes in the matrix formulation and the means of milling the powders also complicated resolution of the three fuel compact defect fractions, DUF, exposed kernel fraction (EKF), and the silicon carbide defect fraction (SDF). Characterization data from BWXT-NOG had some anomalous results, so samples of the fuel compacts and overcoated TRISO particles were also analyzed by Oak Ridge National Laboratory (ORNL) to ensure that the defect fractions were accurately characterized.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

The Impact of Ethylenediaminetetraacetic Acid (EDTA) on the Sorption of Nd(III), Th{sup (IV)}, and U(VI) onto Dolomite in WIPP-Relevant Brines, GWB and ERDA-6 - 20356

Storage of legacy, transuranic waste at the Waste Isolation Pilot Plant (WIPP) requires accurate risk models for performance assessments. These models must predict the long-term fate and transport of contaminants in the WIPP and surrounding environment. Laboratory support is necessary for the development of an accurate model through better understanding of contaminant behavior in the WIPP. The WIPP is a deep geologic repository that is characterized by high ionic strength due to evaporite deposits in the Salado formation (porewaters up to 7.4 M). High concentrations of sodium chloride (NaCl), calcium chloride (CaCl{sub 2}), and magnesium chloride (MgCl{sub 2}) are particularly of concern due to their potential impact on solubility and ultimately transport of contaminants of concern. Additionally, ligands capable of forming strong complexes with metals are found in significant concentrations in the WIPP environment due to their disposal from waste processing and formation during degradation of repository components (e.g. cellulose degradation by calcium hydroxide in cement). Consequently, there is a need to investigate the fate and transport of contaminants in the WIPP environment with a focus on the effects of high ionic strength and strongly coordinating ligands. Contaminants of high concern include the actinides (U(VI), Pu(IV), and Am(III)). Laboratory support of the WIPP modeling efforts was provided by this research. A series of batch experiments were utilized to study the impact of ionic strength, contaminant concentration, and the presence of ethylenediaminetetraacetic acid (EDTA) on the sorption of Nd(III), Th(IV), and U(VI) onto dolomite, a carbonate mineral found within the Culebra formation. The Culebra formation is the most transmissive layer above the WIPP, making transport of contaminants the most likely route in previous risk assessments. Two brines specifically designed to imitate conditions within the WIPP environment were used in these experiments. The U.S. Energy Research and Development Administration Well 6 (ERDA-6, 95%) brine simulates a low Mg environment, while the generic weep brine (GWB, 95%) simulates the WIPP environment with a high Mg concentration. Mg is added to the repository in the form of MgO as an engineered barrier and is naturally present in some formations. It is expected to scavenge carbonate from solutions decreasing formation of the highly soluble and competitive uranium-carbonate complexes. EDTA is used during manipulations of nuclear materials due to its ability to form strong, stable complexes with the actinides and may be found in high concentrations (up to 0.08 mM) within the WIPP as waste canisters degrade. Further, it may provide additional avenues for unwanted transport of contaminants. Nd(III) and Th(IV) were used as stable analogues of Am(III) and Pu(IV), respectively, to represent the most common oxidation states of actinides in the WIPP environment in addition to U(VI). The potential for colloid formation was also investigated with low and high concentrations of contaminants (10 and 1000 μg/L) using three size-dependent particle separation steps. The results of this research provide a better understanding of potential behavior of actinides in the presence of EDTA and within WIPP-relevant brines. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
NASA NTRSDate not supplied

An Investigation Into Transecting Satellites in Future Space Traffic Management Scenarios

The number of satellites expected to populate the near-Earth space environment is set to dramatically increase in the coming decade as new large constellations are approved and deployed. Current strategies for placing new batches of these satellites on orbit often involve launching into an initial orbit, and then performing apogee raising maneuvers to reach a target altitude. Similarly, end-of-life planning for these constellation satellites can consist of de-orbit burns that lower perigee to permit disposal via re-entry. Both the raising and de-orbiting maneuvers can result in the individual satellites traveling in high-eccentricity orbits that have the potential to transect other spacecraft trajectories. While individual large constellations may be able to coexist in separate altitude and inclination bands, having thousands of satellites moving between these bands as new satellites are replaced and old ones are removed could pose additional collision risks. Similar concerns have been raised regarding the impact that large numbers of university-class CubeSats might have in terms of their overall collision risk, especially as these satellites typically do not have propulsion systems for active maneuvering. To assess the impact that transecting satellites might have to future space traffic management strategies, this study explored a variety of future realistic scenarios using a high-fidelity simulation tool. The model can simulate the orbit of tens of thousands of resident space objects (RSOs) simultaneously, to include active satellites, debris, rocket bodies, or even future hypothetical scenarios, using a realistic force model that incorporates non-spherical gravity, atmospheric drag, solar radiation pressure, and more. As the model is run forward in time, various statistics and meta-data are gathered on any predicted conjunction event, providing insight into the nature and frequency of potential collisions, e.g., what size are the two satellites, who operates the satellites, are they active or passive objects, etc. Additional customization is available in terms of how probability of collision is computed, and how the probability ellipsoids and screening volumes are determined. The simulation tool also allows for rule-based maneuvers for active satellites, e.g, given an advance conjunction “warning,” one or both of the satellites can maneuver to a safe distance. A wide range of maneuvers can be implemented using impulsive or low-thrust methods, and the latencies can also be varied, e.g., using maneuver lead times of 48 hours, 24 hours, or 12 hours. Validation of the simulation results is performed against current and historical datasets available, to include comparisons to prior conjunction data messages (CDMs), object properties (mass, volume, etc.), and two-line-element records from both public and internal sources. Using the simulation environment, an assessment on the general risks that transecting satellites might pose for hypothetical future space object environments will be presented. This will involve the simulation of approximately 50,000 new large constellation satellites, in addition to the existing catalog of approximately 20,000 known resident space objects (RSOs), over propagation periods of one month to one year. A description of the simulation methodologies, scenarios evaluated, and validation methods will also be presented, as well as a preliminary assessment of the effectiveness of several candidate maneuver strategies that have the potential to reduce collision risk between active satellites.

Brian Gunter↗
NASA NTRS1992

Large scale crystallization of protein pharmaceuticals in microgravity via temperature change

The major objective of this research effort is the temperature driven growth of protein crystals in large batches in the microgravity environment of space. Pharmaceutical houses are developing protein products for patient care, for example, human insulin, human growth hormone, interferons, and tissue plasminogen activator or TPA, the clot buster for heart attack victims. Except for insulin, these are very high value products; they are extremely potent in small quantities and have a great value per gram of material. It is feasible that microgravity crystallization can be a cost recoverable, economically sound final processing step in their manufacture. Large scale protein crystal growth in microgravity has significant advantages from the basic science and the applied science standpoints. Crystal growth can proceed unhindered due to lack of surface effects. Dynamic control is possible and relatively easy. The method has the potential to yield large quantities of pure crystalline product. Crystallization is a time honored procedure for purifying organic materials and microgravity crystallization could be the final step to remove trace impurities from high value protein pharmaceuticals. In addition, microgravity grown crystals could be the final formulation for those medicines that need to be administered in a timed release fashion. Long lasting insulin, insulin lente, is such a product. Also crystalline protein pharmaceuticals are more stable for long-term storage. Temperature, as the initiation step, has certain advantages. Again, dynamic control of the crystallization process is possible and easy. A temperature step is non-invasive and is the most subtle way to control protein solubility and therefore crystallization. Seeding is not necessary. Changes in protein and precipitant concentrations and pH are not necessary. Finally, this method represents a new way to crystallize proteins in space that takes advantage of the unique microgravity environment. The results from two flights showed that the hardware performed perfectly, many crystals were produced, and they were much larger than their ground grown controls. Morphometric analysis was done on over 4,000 crystals to establish crystal size, size distribution, and relative size. Space grown crystals were remarkably larger than their earth grown counterparts and crystal size was a function of PCF volume. That size distribution for the space grown crystals was a function of PCF volume may indicate that ultimate size was a function of temperature gradient. Since the insulin protein concentration was very low, 0.4 mg/ml, the size distribution could also be following the total amount of protein in each of the PCF's. X-ray analysis showed that the bigger space grown insulin crystals diffracted to higher resolution than their ground grown controls. When the data were normalized for size, they still indicated that the space crystals were better than the ground crystals.

Long, Marianna M.↗
NASA NTRSDate not supplied

An Investigation Into Transecting Satellites in Future Space Traffic Management Scenarios

The number of satellites expected to populate the near-Earth space environment is set to dramatically increase in the coming decade as new large constellations are approved and deployed. Current strategies for deploying new batches of these satellites often involve launching into an initial orbit, and then performing apogee raising maneuvers to reach a target altitude. Similarly, end-of-life planning for these constellation satellites can consist of de-orbit burns that lower perigee to permit disposal via re-entry. Both the raising and de-orbiting maneuvers can result in the individual satellites traveling in transecting orbits that have the potential to cross other spacecraft trajectories. While individual large constellations may be able to coexist in separate altitude and inclination bands, having thousands of satellites moving between these bands as new satellites are added and old satellites are removed could pose additional collision risks. Similar concerns have been raised regarding the impact that large numbers of university-class CubeSats might have in terms of their overall collision risk, especially as these satellites typically do not have propulsion systems for active maneuvering. To assess the impact that transecting satellites might have on future space traffic management strategies, this study explored a variety of realistic future scenarios using a high-fidelity simulation tool. The model can simulate the orbit of tens of thousands of resident space objects (RSOs) simultaneously, to include active satellites, debris, rocket bodies, or even future hypothetical satellite constellations, using a realistic force model that incorporates non-spherical gravity, atmospheric drag, and solar radiation pressure, as well as station-keeping. The simulation can be customized to accommodate different methods of calculating the probability of collision, as well as the process for determining probability ellipsoids and screening volumes. This makes it possible to replicate, and compare, different processes used by different spacecraft operators and space situational awareness (SSA) providers. As the model is run forward in time, each conjunction event is recorded, allowing for the analysis of statistics and meta-data related to these events, providing insight into the nature and frequency of potential collisions, such as whether are they active or passive objects, what size are the two objects, and who owns the objects (if known). This information makes it possible to characterize how changes to the status quo affect the number and type of conjunctions that occur, as well as the distributional effects on various types of satellite operators. To assess the general risks that transecting satellites might pose for hypothetical future space object environments, approximately 60,000 new large constellation satellites were considered, in addition to the existing catalog of approximately 7800 known resident space objects (RSOs), over a simulation period of one year. The results indicate that the future space environment will introduce a non-linear increase in conjunction events as the number of RSOs also increase. This will require adjustments to spacecraft fuel budgets in order to conduct the avoidance maneuvers necessary to minimize collision risk, both for existing and new satellites. This increase is due in large part to the higher density of RSOs and the overlap between some constellation orbits. Current catalog objects were shown to require three times more ∆V for collision avoidance (CA) maneuvers in the simulated future environment, and some constellation spacecraft were estimated to devote the majority of their annual ∆V to CA. The impact of small satellites was found to be proportional for the current space environment, and actually decreased in terms of percentage for the future scenario, suggesting that small satellites do not pose an outsized collision risk. Lastly, transecting satellites were found to contribute thousands of additional conjunctions outside of their operational orbit, and may require up to an additional 5% in CA maneuver fuel allocation.

conjunction assessment↗
DOE OSTI2023

Total metals, carbon, nitrogen & anion concentration data; Slate River & East River floodplains, Crested Butte, CO; May 2022-October 2022

This data package includes processed and undiluted measurements for metal, total carbon, total nitrogen, and anion concentrations from pore water (groundwater) and surface water samples from the Slate River and East River floodplains of Crested Butte, CO, focus field sites for the SLAC Floodplain Hydro-Biogeochemistry SFA. The data was generated as part of the work targeting the overarching research question for the SLAC SFA: How do ubiquitous subsurface interfaces mediate molecular-scale biogeochemical processes and groundwater quality in floodplains and watersheds? Samples were collected between May and October of 2022. These measurements were all recorded at the Arizona Laboratory for Emerging Contaminants (ALEC) at the University of Arizona located in Tucson, AZ. Groundwater samples were extracted from a network of installed rhizon (Rhizosphere Research Products, part no. 19.60.21F, 0.6 micrometer mesh size) and piezometer wells within the river floodplain. All water samples were shaded from sun exposure during extraction from the subsurface and preserved at 4C until measured at ALEC.Analysis by ICP-MS (metals):Measurements for total metals were made on the Agilent 7700x ICP-MS (for total metals) – Agilent Technologies, Santa Clara, CA. The analytical QA/QC protocol was adapted from US EPA Method 200.8 for analysis by ICP-MS. Calibration standards were prepared from multi-element stock solutions (SPEX Certiprep, Metuchen, NJ). Calibration curves include at least 7 points with correlation coefficients > 0.995. The QC protocol includes a continuing calibration blank (CCB), a continuing calibration verification (CCV) solution and at least one quality control sample (QCS) to be analyzed just after calibration and again after every 12 samples and at the completion of the run. The QCS solutions are from an independent source, such as NIST SRM 1643e - Trace elements in water, or QCS solutions from High Purity Standards (Charleston, SC). Acceptable QC responses must be between 90 and 110% of the certified value. Lastly, a suitable internal standard (usually Rh, In, Ga or Ge) is added using on-line addition into the sample line and mixing tee.Analysis by Shimadzu TOC-L (TOC/TN):The TOC-L system is a combustion technique where liquid samples are injected and combusted into CO2 for carbon detection by non-dispersive infrared (NDIR) and NO for detection by chemiluminescence. A calibration curve using five standard solutions between 0.1 and 7 ppm for carbon and 0.05 and 3.5 ppm for nitrogen is made for each type of measurement with a linearity >0.99. All samples, standards, and QC’s are prepared in 24mL scintillation vials that have been baked for 4hrs at 475 Cº and made using RO water (18.2mΩ). QC’s include a calibration blank check (CCB), continuing calibration check (CCC), and a certified reference material check (CRM). All QC’s are within ±10% error and are run before and after each batch of samples. Samples are diluted and rerun if any measurement concentrations are above the highest standard.Analysis by Ion Chromatography (Anions):The instrument used is the Thermo Scientific Dionex ICS-6000 using AS+AG22 column set for anion analysis with sodium carbonate eluent. A calibration curve using five standard solutions between 5 and 250 umol/L is made with a linearity >0.99. Standards and QC’s are prepared in 15mL polypropylene conical tubes, pipetted along with the samples into 1.5mL polypropylene vials. Dilutions are made using RO water (18.2mΩ). QC’s include a calibration blank check (CCB), continuing calibration check (CCC), and a certified reference material check (CRM). All QC’s are within ±10% error and are run before and after each batch of samples. Samples are diluted and rerun if any measurement concentrations are above the highest standard.All files are in csv format.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

X-ray Computed Tomography of Irradiated and Unirradiated AGR-3/4 Compacts

X-ray Computed Tomography (XCT) has been utilized to image and characterize compacts from the combined third and fourth irradiation of the Advanced Gas Reactor (AGR) Program, AGR-3/4, fuel. The experiment contained tristructural isotropic (TRISO)-coated fuel particles as well as designed-to-fail (DTF) fuel particles. Two irradiated compacts, representing the lower and higher range of AGR-3/4 burnup (4.85% and 14.92% fissions per initial heavy metal atom FIMA) were examined. These represent the first known highly irradiated TRISO fuel compacts to be examined via X-ray CT. Additionally, two unirradiated compacts from the same production batch as the examined irradiation compacts were also imaged for a baseline comparison. As XCT of irradiated TRISO compacts is not a commonly implemented characterization technique, a significant portion of the report focuses on developed methodology and imaging conditions. A specialized sample shielding device was developed and fabricated specifically to limit received dose to staff during sample preparation for XCT and to minimize excess gamma radiation dose to sensitive electronic components with the utilized X-ray system. Significant penetration through the uranium oxycarbide fuel kernels by significantly hardening the X-ray beam with specialized proprietary filters acquired from Carl Zeiss NTS Ltd. The filter utilized resulted in an average X ray photon energy of ~110 keV which approaches uranium’s K-edge (~115 keV), maximizing penetration for a microfocus X-ray source. The gamma-radiation emitted from the irradiated AGR-3/4 TRISO compacts, has the same properties and mechanisms for interaction with matter as X-rays, thus the detection of gamma-radiation by the utilized X-ray detectors was initially a concern. However, although ?-rays did produce an observable signal on the X-ray detector, its contribution to the overall imaging results appeared negligible upon 3D reconstruction. The neglibile impact on the resulting 3D reconstructed volumes were likely the result of: (1) a significantly lower detection efficiency for ?-rays relative to X-rays; (2) An X-ray flux at the detector several orders of magnitude higher than that of the impinging ?-rays from the irradiated compacts. These results suggest that irradiated compacts with significantly higher radiation fields can be examined in the future if an acceptable route for sample handling and preparation can be determined. Additionally, the 3D imaging results of XCT can provide a valuable means of assessing compacts. While in many ways complimentary to traditional post irradiation examination techniques such as optical ceramography, XCT can provide additional insight into compact features traditionally difficult to discern directly from cross-sectional imaging alone. Preliminary analyses on kernel size, morphology (aspect ratio and sphericity), and kernel orientation were presented. Sphericity, a simple morphological shape descriptor, was utilized to screen for kernel extrusions within the high burnup compact. The number of kernel extrusions identified via XCT represented an approximate two-fold increase from the quantity of extruded particles observed (via optical ceramography) in adjacent compacts from the same irradiation capsule. While numerical analysis of the compact datasets was highly preliminary, initial results show promise for providing complimentary metrics to current AGR-3/4 PIE and potentially additional insight into the processes driving TRISO fuel degradation during reactor operation. Additional analyses to be performed at a later date include a more detailed examination of kernel size, kernel sphericity (and observed kernel extrusions), and sphericity. Given all particles can be observed in a single data volume possible correlation of spatial position with observed kernel features will also be made at a later date.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS2005

Removal of organic contaminants by RO and NF membranes

Rejection characteristics of organic and inorganic compounds were examined for six reverse osmosis (RO) membranes and two nanofiltration (NF) membranes that are commercially available. A batch stirred-cell was employed to determine the membrane flux and the solute rejection for solutions at various concentrations and different pH conditions. The results show that for ionic solutes the degree of separation is influenced mainly by electrostatic exclusion, while for organic solutes the removal depends mainly upon the solute radius and molecular structure. In order to provide a better understanding of rejection mechanisms for the RO and NF membranes, the ratio of solute radius (r(i,s)) to effective membrane pore radius (r(p)) was employed to compare rejections. An empirical relation for the dependence of the rejection of organic compounds on the ratio r(i,s)/r(p) is presented. The rejection for organic compounds is over 75% when r(i,s)/r(p) is greater than 0.8. In addition, the rejection of organic compounds is examined using the extended Nernst-Planck equation coupled with a steric hindrance model. The transport of organic solutes is controlled mainly by diffusion for the compounds that have a high r(i,s)/r(p) ratio, while convection is dominant for compounds that have a small r(i,s)/r(p) ratio. c2005 Elsevier B.V. All rights reserved.

NASA Discipline Life Sciences Technologies↗
NASA NTRS2017

Gravitational Waves and Gamma-Rays from a Binary Neutron Star Merger: GW170817 and GRB 170817A

On 2017 August 17, the gravitational-wave event GW170817 was observed by the Advanced LIGO and Virgo detectors, and the gamma-ray burst (GRB) GRB170817A was observed independently by the Fermi Gamma-ray Burst Monitor, and the Anti-Coincidence Shield for the Spectrometer for the International Gamma-Ray Astrophysics Laboratory. The probability of the near-simultaneous temporal and spatial observation of GRB 170817A and GW170817 occurring by chance is 5.0 x 10(exp -8). We therefore confirm binary neutron star mergers as a progenitor of short GRBs. The association of GW170817 and GRB 170817A provides new insight into fundamental physics and the origin of short GRBs. We use the observed time delay of (+1.74 +/- 0.05) s between GRB170817A and GW170817 to: (i) constrain the difference between the speed of gravity and the speed of light to be between -3 x 10(exp-16) times the speed of light, (ii) place new bounds on the violation of Lorentz invariance, (iii) present a new test of the equivalence principle by constraining the Shapiro delay between gravitational and electromagnetic radiation. We also use the time delay to constrain the size and bulk Lorentz factor of the region emitting the gamma-rays. GRB170817A is the closest short GRB with a known distance, but is between 2 and 6 orders of magnitude less energetic than other bursts with measured redshift. A new generation of gamma-ray detectors, and subthreshold searches in existing detectors, will be essential to detect similar short bursts at greater distances. Finally, we predict a joint detection rate for the Fermi Gamma-ray Burst Monitor and the Advanced LIGO and Virgo detectors of 0.1 - 1.4 per year during the 2018--2019 observing run and 0.3 - 1.7 per year at design sensitivity.

Gravitational wave↗
NASA NTRS2004

Manufacturing High-Quality Carbon Nanotubes at Lower Cost

A modified electric-arc welding process has been developed for manufacturing high-quality batches of carbon nanotubes at relatively low cost. Unlike in some other processes for making carbon nanotubes, metal catalysts are not used and, consequently, it is not necessary to perform extensive cleaning and purification. Also, unlike some other processes, this process is carried out at atmospheric pressure under a hood instead of in a closed, pressurized chamber; as a result, the present process can be implemented more easily. Although the present welding-based process includes an electric arc, it differs from a prior electric-arc nanotube-production process. The welding equipment used in this process includes an AC/DC welding power source with an integral helium-gas delivery system and circulating water for cooling an assembly that holds one of the welding electrodes (in this case, the anode). The cathode is a hollow carbon (optionally, graphite) rod having an outside diameter of 2 in. (approximately equal to 5.1 cm) and an inside diameter of 5/8 in. (approximately equal to 1.6 cm). The cathode is partly immersed in a water bath, such that it protrudes about 2 in. (about 5.1 cm) above the surface of the water. The bottom end of the cathode is held underwater by a clamp, to which is connected the grounding cable of the welding power source. The anode is a carbon rod 1/8 in. (approximately equal to 0.3 cm) in diameter. The assembly that holds the anode includes a thumbknob- driven mechanism for controlling the height of the anode. A small hood is placed over the anode to direct a flow of helium downward from the anode to the cathode during the welding process. A bell-shaped exhaust hood collects the helium and other gases from the process. During the process, as the anode is consumed, the height of the anode is adjusted to maintain an anode-to-cathode gap of 1 mm. The arc-welding process is continued until the upper end of the anode has been lowered to a specified height above the surface of the water bath. The process causes carbon nanotubes to form in the lowest 2.5 cm of the anode. It also causes a deposit reminiscent of a sandcastle to form on the cathode. The nanotube-containing material is harvested. The cathode and anode can then be cleaned (or the anode is replaced, if necessary) and the process repeated to produce more nanotubes. Tests have shown that the process results in approximately equal to 50-percent yield of carbon nanotubes (mostly of the single-wall type) of various sizes. Whereas the unit cost of purified single-wall carbon nanotubes produced by other process is about $1,000/g in the year 2000, it has been estimated that for the present process, the corresponding cost would be about $10/g.

Benavides, Jeanette M.↗