Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Waveform Parameters”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
DOE OSTI2019

Hysteresis and degaussing of H1 dipole magnets

Hysteresis was observed in the H1 dipole magnets in CBETA SX line. This study is the first step in order to understand and mitigate the effects this has on field reproducibility. Ansys Maxwell 19.2 was used to model the MS1DIP05 magnet with a hysteretic core. The parameter space for a degaussing procedure using the trim coils was explored. It was found that significant degaussing can be obtained with a decaying ringing waveform of magnitudes above 10 A, so long as the frequency ƒ and decay constant w were chosen such that ƒ >> w. The circuit properties of the magnet were simulated and explored using a sinusoidal voltage input. It was found that for low frequencies ƒ << 1 Hz, the magnet behaves as a series LR circuit with R = (28.3 ± 0.5) mΩ and L = (5.7 ± 0.1) mH. At higher frequencies, hysteretic effects become significant, and resistance becomes proportional to the frequency due to hysteretic losses. A drop and saturation in inductance for higher frequencies was observed in the simulation data. Numerical instabilities were found for excitations below small voltages V < 50 mV. Experimental results on degaussing and current corrections were collected with Hall probe measurements. Good qualitative agreement with simulation results was found, but due to B-H curve details quantitative comparisons were inaccurate. Two procedures, MaxOp and MaxNull, were designed to produce repeatable operating field values to within 0.1 G.

43 PARTICLE ACCELERATORS↗
NASA NTRS1973

Nonlinear gas oscillations in pipes. I - Theory.

The problem of forced acoustic oscillations in a pipe is studied theoretically. The oscillations are produced by a moving piston in one end of the pipe, while a variety of boundary conditions ranging from a completely closed to a completely open mouth at the other end are considered. The linear theory predicts large amplitudes near resonance and that nonlinear effects become crucially important. By expanding the equations of motion in a series in the Mach number, both the amplitude and waveform of the oscillation are predicted there. In both the open- and closed-end cases the need for shock waves in some range of parameters is found. The amplitude of the oscillation is different for the two cases, however, being proportional to the square root of the piston amplitude in the closed-end case and to the cube root for the open end.

Jimenez, J.↗
DOE OSTI2026

Designing the Protocols for Programmable Ammonia Catalysis

Programmable catalysis can provide a more energy-efficient and cost-effective route to enhancing commercial ammonia production, a key process in the advancement of renewable energy technologies and the manufacture of fertilizers and basic chemicals. This work explores the computational discovery of optimal forcing protocols to drive such dynamic catalysis models. By employing matrix-free time-stepper methods, coupled with an optimization approach, that integrates Bayesian optimization with a Bayesian continuation strategy to efficiently discover the periodic steady states of such periodically forced systems, we enable the discovery of complex optimal catalyst strain waveforms, while ensuring robust solver convergence. We demonstrate the flexibility of our approach to discover optimized forcing protocols under varying physical constraints on strain modulation or other catalyst operating parameters. We show that these can have a temporal structure more complex than simple step functions. In order to detect undesirable catalytic loops that may correlate with overall reduced performance, we perform a study using graph-theoretical analysis to investigate the dynamics of catalytic kinetic networks formed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2019

Accelerating full waveform inversion via source stacking and cross-correlations

SUMMARY Accurate synthetic seismic wavefields can now be computed in 3-D earth models using the spectral element method (SEM), which helps improve resolution in full waveform global tomography. However, computational costs are still a challenge. These costs can be reduced by implementing a source stacking method, in which multiple earthquake sources are simultaneously triggered in only one teleseismic SEM simulation. One drawback of this approach is the perceived loss of resolution at depth, in particular because high-amplitude fundamental mode surface waves dominate the summed waveforms, without the possibility of windowing and weighting as in conventional waveform tomography. This can be addressed by redefining the cost-function and computing the cross-correlation wavefield between pairs of stations before each inversion iteration. While the Green’s function between the two stations is not reconstructed as well as in the case of ambient noise tomography, where sources are distributed more uniformly around the globe, this is not a drawback, since the same processing is applied to the 3-D synthetics and to the data, and the source parameters are known to a good approximation. By doing so, we can separate time windows with large energy arrivals corresponding to fundamental mode surface waves. This opens the possibility of designing a weighting scheme to bring out the contribution of overtones and body waves. It also makes it possible to balance the contributions of frequently sampled paths versus rarely sampled ones, as in more conventional tomography. Here we present the results of proof of concept testing of such an approach for a synthetic 3-component long period waveform data set (periods longer than 60 s), computed for 273 globally distributed events in a simple toy 3-D radially anisotropic upper mantle model which contains shear wave anomalies at different scales. We compare the results of inversion of 10 000 s long stacked time-series, starting from a 1-D model, using source stacked waveforms and station-pair cross-correlations of these stacked waveforms in the definition of the cost function. We compute the gradient and the Hessian using normal mode perturbation theory, which avoids the problem of cross-talk encountered when forming the gradient using an adjoint approach. We perform inversions with and without realistic noise added and show that the model can be recovered equally well using one or the other cost function. The proposed approach is computationally very efficient. While application to more realistic synthetic data sets is beyond the scope of this paper, as well as to real data, since that requires additional steps to account for such issues as missing data, we illustrate how this methodology can help inform first order questions such as model resolution in the presence of noise, and trade-offs between different physical parameters (anisotropy, attenuation, crustal structure, etc.) that would be computationally very costly to address adequately, when using conventional full waveform tomography based on single-event wavefield computations.

Romanowicz, Barbara↗
DOE OSTI2024

Monitoring spatiotemporal evolution of fractures during hydraulic stimulations at the first EGS collab testbed using anisotropic elastic-waveform inversion

The EGS Collab project acquired continuous active-source seismic monitoring (CASSM) data before, during, and after hydraulic stimulations at the first testbed at the depth of 4850 ft (1478 m) at the Sanford Underground Research Facility in Lead, South Dakota, for monitoring fracture creation and evolution. CASSM acquisition was conducted using 24 hydrophones, 18 accelerometers, and 17 piezoelectric sources within four fracture-parallel wells and two orthogonal wells. 3D anisotropic traveltime tomography and anisotropic elastic-waveform inversion of the campaign cross-borehole seismic data show that the rock within the stimulation region is a heterogeneous horizontal transverse isotropic medium. Here we use these inversion results as the initial models and apply 3D anisotropic first-arrival traveltime tomography and 3D anisotropic elastic-waveform inversion to the CASSM data acquired after each stimulation in May, 2018 and December, 2018. We observe the spatiotemporal evolution of seismic velocities and anisotropic parameters caused by hydraulic fracture stimulations, showing the regions of rock alternation caused by hydraulic fracture stimulation.

15 GEOTHERMAL ENERGY↗
NASA NTRS1975

Suppression of nonlinear oscillations in combustors with partial length acoustic liners

An analytical model is formulated for a three-dimensional nonlinear stability problem in a rocket motor combustion chamber. The chamber is modeled as a right circular cylinder with a short (multi-orifice) nozzle, and an acoustic linear covering an arbitrary portion of the cylindrical periphery. The combustion is concentrated at the injector and the gas flow field is characterized by a mean Mach number. The unsteady combustion processes are formulated using the Crocco time lag model. The resulting equations are solved using a Green's function method combined with numerical evaluation techniques. The influence of acoustic liners on the nonlinear waveforms is predicted. Nonlinear stability limits and regions where triggering is possible are also predicted for both lined and unlined combustors in terms of the combustion parameters.

Espander, W. R.↗
NASA NTRSDate not supplied

Uncertainty Quantification of CFD Model Assumptions Against Sonic Boom Noise Prediction of a Commercial Supersonic Transport

This paper presents the results of uncertainty modeling of sonic boom noise generation from commercial supersonic transport considering the Spalart-Allmaras (SA) turbulence modeling parameters as well as Mach number, angle of attack and altitude. Sample generation and analysis for this uncertainty model was performed by UQPCE, which is a software package developed at the NASA Langley Research Center. To build the uncertainty model, 42 cases of sonic boom noise calculation were performed. Computation of the ground noise can be briefly summarized in two steps. First, the near field pressure waveforms are sampled from CFD calculation using the NASA Langley’s FUN3D solver. Second, this information is passed to an atmospheric propagation code, sBOOM, which solves an augmented Burger’s equation and simulates how the near field waveforms will change while passing through the atmosphere. The ground signature is further processed to obtain the perceived loudness, PLdB. Having a high spatial resolution near the shockwave in the CFD calculation is critical in sonic boom noise prediction. Because the variation in the input parameters for the current uncertainty quantification (UQ) study is likely to lead to change in shock location, angle and strength, the grid adaptation for shock capturing is independently applied for each condition. The final mesh used in the CFD calculation consists of approximately 420 million cells. The pressure signatures are sampled at three, four and five body lengths away from the aircraft to make sure the three dimensional effects around the aircraft are resolved. The results of the UQ analysis shows that within the three aleatory variables, the angle of attack had the most impact against ground noise, followed by the altitude and the Mach number. Between the two SA model parameters, the Kármán constant (𝜅) was significantly more important than the turbulent Prandtl number (𝜎), but these two parameters were only marginally significant in the overall prediction variance in ground noise. The UQ procedure explained in this paper can be widely applied to other model parameters.

Uncertainty Quantification↗
DOE OSTI2020

Optically targeted search for gravitational waves emitted by core-collapse supernovae during the first and second observing runs of advanced LIGO and advanced Virgo

In this work, we present the results from a search for gravitational-wave transients associated with core-collapse supernovae observed within a source distance of approximately 20 Mpc during the first and second observing runs of Advanced LIGO and Advanced Virgo. No significant gravitational-wave candidate was detected. We report the detection efficiencies as a function of the distance for waveforms derived from multidimensional numerical simulations and phenomenological extreme emission models. Furthermore, the sources with neutrino-driven explosions are detectable at the distances approaching 5 kpc, and for magnetorotationally driven explosions the distances are up to 54 kpc. However, waveforms for extreme emission models are detectable up to 28 Mpc. For the first time, the gravitational-wave data enabled us to exclude part of the parameter spaces of two extreme emission models with confidence up to 83%, limited by coincident data coverage. Besides, using ad hoc harmonic signals windowed with Gaussian envelopes, we constrained the gravitational-wave energy emitted during core collapse at the levels of 4.27×10 -4 M ⊙ c 2 and 1.28×10 -1 M ⊙ c 2 for emissions at 235 and 1304 Hz, respectively. These constraints are 2 orders of magnitude more stringent than previously derived in the corresponding analysis using initial LIGO, initial Virgo, and GEO 600 data.

79 ASTRONOMY AND ASTROPHYSICS↗
NASA NTRS2020

Optically targeted search for gravitational waves emitted by core-collapse supernovae during the first and second observing runs of advanced LIGO and advanced Virgo

We present the results from a search for gravitational-wave transients associated with core-collapse supernovae observed within a source distance of approximately 20 Mpc during the first and second observing runs of Advanced LIGO and Advanced Virgo. No significant gravitational-wave candidate was detected. We report the detection efficiencies as a function of the distance for waveforms derived from multidimensional numerical simulations and phenomenological extreme emission models. The sources with neutrino-driven explosions are detectable at the distances approaching 5 kpc, and for magnetorotationally driven explosions the distances are up to 54 kpc. However, waveforms for extreme emission models are detectable up to 28 Mpc. For the first time, the gravitational-wave data enabled us to exclude part of the parameter spaces of two extreme emission models with confidence up to 83%, limited by coincident data coverage. Besides, using ad hoc harmonic signals windowed with Gaussian envelopes, we constrained the gravitational-wave energy emitted during core collapse at the levels of 4.27 × 10^(−4) Mꙩc^(2) and 1.28 × 10^(−1) Mꙩc^(2) for emissions at 235 and 1304 Hz, respectively. These constraints are 2 orders of magnitude more stringent than previously derived in the corresponding analysis using initial LIGO, initial Virgo, and GEO 600 data.

B. P. Abbott↗
NASA NTRSDate not supplied

Uncertainty Quantification of CFD Model Assumptions Against Sonic Boom Noise Prediction of a Commercial Supersonic Transport

This paper presents the results of uncertainty modeling of sonic boom noise generation from commercial supersonic transport considering the Spalart-Allmaras (SA) turbulence modeling parameters as well as Mach number, angle of attack and altitude. Sample generation and analysis for this uncertainty model was performed by UQPCE, which is a software package developed at the NASA Langley Research Center. To build the uncertainty model, 42 cases of sonic boom noise calculation were performed. Computation of the ground noise can be briefly summarized in two steps. First, the near field pressure waveforms are sampled from CFD calculation using the NASA Langley’s FUN3D solver. Second, this information is passed to an atmospheric propagation code, sBOOM, which solves an augmented Burger’s equation and simulates how the near field waveforms will change while passing through the atmosphere. The ground signature is further processed to obtain the perceived loudness, PLdB. Having a high spatial resolution near the shock wave in the CFD calculation is critical in sonic boom noise prediction. Because the variation in the input parameters for the current uncertainty quantification (UQ) study is likely to lead to change in shock location, angle and strength, the grid adaptation for shock capturing is independently applied for each condition. The final mesh used in the CFD calculation consists of approximately 420 million cells. The pressure signatures are sampled at three, four and five body lengths away from the aircraft to make sure the three dimensional effects around the aircraft are resolved. The results of the UQ analysis shows that within the three aleatory variables, the angle of attack had the most impact against ground noise, followed by the altitude and the Mach number. Between the two SA model parameters, the Kármán constant (𝜅) was significantly more important than the turbulent Prandtl number (𝜎), but these two parameters were only marginally significant in the overall prediction variance in ground noise. The UQ procedure explained in this paper can be widely applied to other model parameters.

Uncertainty Quantifications↗
DOE OSTI2018

Implementation of the Waveform Correlation Event Detection System (WCEDS) Method for Regional Seismic Event Detection in Utah

Backprojection techniques are a class of methods for detecting and locating events that have been successfully implemented at local scales for dense networks. This paper develops the framework for applying a backprojection method to detect and locate a range of event sizes across a heteorogeneous regional network. This article extends previous work on the development of a backprojection method for local and regional seismic event detection, the Waveform Correlation Event Detection System (WCEDS). The improvements outlined here make the technique much more flexible for regional earthquake or explosion monitoring. We first explore how the backprojection operator can be formulated using either a travel-time model or a stack of full waveforms, showing that the former approach is much more flexible and can lead to the detection of smaller events, and to significant improvements in the resolution of event parameters. Second, we discuss the factors that influence the grid of event hypotheses used for backprojection, and develop an algorithm for generating suitable grids for networks with variable density. Third, we explore the effect of including different phases in the backprojection operator, showing that the best results for the study region can be obtained using only the Pg phase, and by including terms for penalizing early arrivals when evaluating the fit for a given event hypothesis. Fourth, we incorporate two parallel backprojection computations with different distance thresholds to enable the robust detection of both network-wide and small (sub-network-only) events. Finally, the set of improvements are outlined by applying WCEDS to four example events on the University of Utah Seismograph Stations (UUSS) network.

58 GEOSCIENCES↗
NASA NTRS1994

Atmospheric propagation at larger lateral distances from the flight track

Sonic booms received on the ground tend to be restricted to a region of finite lateral extent below the flight track. This occurs because of refraction and because the effective speed of sound, even with winds taken into account, decreases with altitude in the lower atmosphere. Not all rays proceeding initially downwards from the flight track within an allowable range of initial directions will reach the ground. The restricted region which can be reached by rays impacting the ground is known as the primary carpet. However, weak rumbles are heard in the nominal shadow zone beyond the edge of this carpet. A full wave theory is necessary for explaining waveforms in that region, and the present paper gives a matched asymptotic expansion technique for a suitable approximate full wave theory that involves a relatively small number of parameters. The outer solution is derived from the structure of the system of rays that impact near the corridor edge; the inner solution involves a solution of the parabolic equation and results in the special functions encountered in the diffraction of sound over the tops of hills.

Pierce, Allan D.↗
NASA NTRS2011

Achievable Performance and Effective Interrogator Design for SAW RFID Sensor Tags

For many NASA missions, remote sensing is a critical application that supports activities such as environmental monitoring, planetary science, structural shape and health monitoring, non-destructive evaluation, etc. The utility of the remote sensing devices themselves is greatly increased if they are passive that is, they do not require any on-board power supply such as batteries and if they can be identified uniquely during the sensor interrogation process. Additional passive sensor characteristics that enable greater utilization in space applications are small size and weight, long read ranges with low interrogator power, ruggedness, and operability in extreme environments (vacuum, extreme high/low temperature, high radiation, etc.) In this paper, we consider one very promising passive sensor technology, called surface acoustic wave (SAW) radio-frequency identification (RFID), that satisfies all of these criteria. Although SAW RFID tags have great potential for use in numerous space-based remote sensing applications, the limited collision resolution capability of current generation tags limits the performance in a cluttered sensing environment. That is, as more SAW-based sensors are added to the environment, numerous tag responses are superimposed at the receiver and decoding all or even a subset of the telemetry becomes increasingly difficult. Background clutter generated by reflectors other than the sensors themselves is also a problem, as is multipath interference and signal distortion, but the limiting factor in many remote sensing applications can be expected to be tag mutual interference. This problem may be greatly mitigated by proper design of the SAW tag waveform, but that remains an open research problem, and in the meantime, several other related questions remain to be answered including: What are the fundamental relationships between tag parameters such as bit-rate, time-bandwidth-product, SNR, and achievable collision resolution? What are the differences in optimal or near-optimal interrogator designs between noise-limited environments and interference-limited environments? What are the performance characteristics of different interrogator designs in term of parameters such as transmitter power level, range, and number of interfering tags? In this paper, we present the results of a research effort aimed at providing at least partial answers to all of these questions.

Barton, Richard J.↗
DOE OSTI2021

A generalized machine learning workflow to visualize mechanical discontinuity

Accurate detection and mapping of mechanical discontinuity in materials has widespread industrial and research applications. Herein, we developed a generalized machine-learning framework for visualizing single mechanical discontinuity embedded in material of any composition, velocity, density, porosity, and size with limited data. The proposed visualization of discontinuity requires accurate estimations of the length, location, and orientation of the embedded discontinuity by processing multipoint wave-transmission measurements. k-Wave simulator is used to create a large dataset of elastic waveforms recorded during multi-point wave-transmission measurements through materials containing single mechanical discontinuity. k-Wave simulator considers the wave attenuation, dispersion, and mode conversion in wave motion. Discrete wavelet transform (DWT) and statistical feature extraction are essential for data preprocessing prior to the data-driven model development. DWT also minimizes the effect of noise. Using hyper-parameter tuning and cross validation, gradient boosting regression can visualize the mechanical discontinuity with an accuracy of 0.85, in terms of coefficient of determination. A double-layered neural network-based regression has better performance with an accuracy of 0.95. Use of convolutional neural network converts the predictive task from a waveform processing to an image processing problem. Convolutional neural network achieved a generalization performance of 0.91. The proposed generalized workflow requires robust simulation of wave propagation, signal processing, feature engineering, and model evaluation. Sensors closest to the source and those located opposite the source are the most significant for the desired visualization. Notably, the sensors closest to the source capture the non-linear associations, whereas the sensor on the border opposite to the source capture the linear associations between the measured waveforms and the properties of the mechanical discontinuity.

42 ENGINEERING↗
NASA NTRS1973

Frequency modulation television analysis: Threshold impulse analysis

A computer program is developed to calculate the FM threshold impulse rates as a function of the carrier-to-noise ratio for a specified FM system. The system parameters and a vector of 1024 integers, representing the probability density of the modulating voltage, are required as input parameters. The computer program is utilized to calculate threshold impulse rates for twenty-four sets of measured probability data supplied by NASA and for sinusoidal and Gaussian modulating waveforms. As a result of the analysis several conclusions are drawn: (1) The use of preemphasis in an FM television system improves the threshold by reducing the impulse rate. (2) Sinusoidal modulation produces a total impulse rate which is a practical upper bound for the impulse rates of TV signals providing the same peak deviations. (3) As the moment of the FM spectrum about the center frequency of the predetection filter increases, the impulse rate tends to increase. (4) A spectrum having an expected frequency above (below) the center frequency of the predetection filter produces a higher negative (positive) than positive (negative) impulse rate.

Hodge, W. H.↗
NASA NTRS2012

Achievable Performance and Effective Interrogator Design for SAW RFID Sensor Tags

For many NASA missions, remote sensing is a critical application that supports activities such as environmental monitoring, planetary science, structural shape and health monitoring, non-destructive evaluation, etc. The utility of the remote sensing devices themselves is greatly increased if they are passive V that is, they do not require any on-board power supply such as batteries V and if they can be identified uniquely during the sensor interrogation process. Additional passive sensor characteristics that enable greater utilization in space applications are small size and weight, long read ranges with low interrogator power, ruggedness, and operability in extreme environments (vacuum, extreme high/low temperature, high radiation, etc.) In this paper, we consider one very promising passive sensor technology, called surface acoustic wave (SAW) radio-frequency identification (RFID), that satisfies all of these criteria. In general, RFID is a method of identifying items using radio waves to interrogate tags encoded with a unique identifier that are affixed to the items of interest. In the case of passive tags, only the interrogator, which transmits power to the tags in the form of radio-frequency electromagnetic radiation, requires access to a power supply. Passive RFID technologies are used today in many applications, including asset tracking and management, security and access control, and remote sensing. To date, most of the development and application in RFID technology has focused on either asset/inventory tracking and control or security and access control because these are the largest commercial application areas. Recently however, there has been growing interest in using passive RFID technology for remote sensing applications, and SAW devices are at the forefront of RFID sensing technology development. Although SAW RFID tags have great potential for use in numerous space-based remote sensing applications, the limited collision resolution capability of current generation tags limits the performance in a cluttered sensing environment. That is, as more SAW-based sensors are added to the environment, numerous tag responses are superimposed at the receiver and decoding all or even a subset of the telemetry becomes increasingly difficult. Background clutter generated by reflectors other than the sensors themselves is also a problem, as is multipath interference and signal distortion, but the limiting factor in many remote sensing applications can be expected to be tag mutual interference. This problem may be greatly mitigated by proper design of the SAW tag waveform, but that remains an open research problem, and in the meantime, several other related questions remain to be answered including: (1) What are the fundamental relationships between tag parameters such as bit-rate, time-bandwidth-product, SNR, and achievable collision resolution? (2) What are the differences in optimal or near-optimal interrogator designs between noise-limited environments and interference-limited environments? (3) What are the performance characteristics of different interrogator designs in term of parameters such as transmitter power level, range, and number of interfering tags? In this paper, we will present the results of a research effort aimed at providing at least partial answers to all of these questions.

Barton Richard J.↗
NASA NTRS2003

Full-Waveform, Wide-Swath Lidar Imaging of Forested and Urban Areas in Leaf-On Conditions: Development, Results and Future Direction

Full-Waveform lidar measurements provide unprecedented views of the vertical and horizontal structure of vegetation and the topography of the Earth s surface. Utilizing a high signal-to-noise ratio lidar system, larger than typical laser footprints (10-20 m), and the recorded time history of interaction between a short-duration (approx. 10 ns) pulse of laser light and the surface of the Earth, full-waveform lidar is able to simultaneously image sub-canopy topography as well as the vertical structure of any overlying vegetation. These data reveal the true 3-D vegetation structure in leaf-on conditions enabling important biophysical parameters such as above-ground biomass to be estimated with unprecedented accuracy. An airborne lidar mission was conducted July-August 2003 in support of the North America Carbon Program. NASA s Laser Vegetation Imaging Sensor (LVIS) was used to image approximately 2,000 km$^2$ in Maine, New Hampshire, Massachusetts and Maryland. Areas with available ground and other data were included (e.g., experimental forests, FLUXNET sites) in order to facilitate as many bio- and geophysical investigations as possible. Data collected included ground elevation and canopy height measurements for each laser footprint, as well as the vertical distribution of intercepted surfaces. Data will be publicly distributed within 6- 12 months of collection. Further details of the mission, including the lidar system technology, the locations of the mapped areas, and examples of the numerous data products that can be derived from the return waveform data products will be presented. Future applications including detection of ground and vegetation canopy changes and a spaceborne implementation of wide-swath, full-waveform imaging lidar will also be discussed.

Blair, James B.↗