Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “TiP”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Model rotor low frequency broadband noise at moderate tip speeds

The results of an experimental investigation of low frequency broadband noise (LFBN) radiated from model helicopter rotors are presented. The results are for a range of tip Mach numbers (Mt) up to 0.50. The effect of rotor blade loading, advance ratio, tip speed, number of blades and free stream turbulence on the sound pressure level (SPL) and the spectrum of LFBN have been investigated. The peak SPL of LFBN appears to follow an M(4) law if the effect of rms turbulence velocity is removed. The peak SPL of LFBN seems to saturate with increases in advance ratio and with blade loading, and is proportional to the square of the turbulence integral scale when the effect of rms turbulence velocity and Mt are removed. Also, a simple peak SPL scaling law for noise from a helicopter rotor in forward flight due to convected sinusoidal gust is developed. The trend predicted by this scaling law is found to be satisfactory for the variation of the peak SPL of LFBN with tip speed.

Humbad, N. G.↗
NASA NTRS1980

Effect of tip vortex structure on helicopter noise due to blade-vortex interaction

A potential cause of helicopter impulsive noise, commonly called blade slap, is the unsteady lift fluctuation on a rotor blade due to interaction with the vortex trailed from another blade. The relationship between vortex structure and the intensity of the acoustic signal is investigated. Unsteady lift on the blades due to blade-vortex interaction is calculated using linear unsteady aerodynamic theory, and expressions are derived for the directivity, frequency spectrum, and transient signal of the radiated noise. The inviscid rollup model of Betz is used to calculate the velocity profile in the trailing vortex from the spanwise distribution of blade tip loading. A few cases of tip loading are investigated, and numerical results are presented for the unsteady lift and acoustic signal due to blade-vortex interaction. The intensity of the acoustic signal is shown to be quite sensitive to changes in tip vortex structures.

Widnall, S. E.↗
NASA NTRS1980

Full scale visualization of the wing tip vortices generated by a typical agricultural aircraft

The trajectories of the wing tip vortices of a typical agricultural aircraft were experimentally determined by flight test. A flow visualization method, similar to the vapor screen method used in wind tunnels, was used to obtain trajectory data for a range of flight speeds, airplane configurations, and wing loadings. Detailed measurements of the spanwise surface pressure distribution were made for all test points. Further, a powered 1/8 scale model of the aircraft was designed, built, and used to obtain tip vortex trajectory data under conditions similar to that of the full-scale test. The effects of light wind on the vortices were demonstrated, and the interaction of the flap vortex and the tip vortex was clearly shown in photographs and plotted trajectory data.

Cross, E. J., Jr.↗
NASA NTRS1981

Reasons for low aerodynamic performance of 13.5-centimeter-tip-diameter aircraft engine starter turbine

The reasons for the low aerodynamic performance of a 13.5 cm tip diameter aircraft engine starter turbine were investigated. Both the stator and the stage were evaluated. Approximately 10 percent improvement in turbine efficiency was obtained when the honeycomb shroud over the rotor blade tips was filled to obtain a solid shroud surface. Efficiency improvements were obtained for three rotor configurations when the shroud was filled. It is suggested that the large loss associated with the open honeycomb shroud is due primarily to energy loss associated with gas transportation as a result of the blade to blade pressure differential at the tip section.

Haas, J. E.↗
NASA NTRS1981

Fundamentals of dendritic solidification. I - Steady-state tip growth. II - Development of sidebranch structure

Systematic measurements of dendrite tip radius and growth velocity in succinonitrile reveal that consideration of dendrite tip stability should be incorporated into the heat transfer theory to determine the steady-state dendritic growth condition. The dendritic stability criterion measured is 2 alpha d0/VR squared = 0.0195, where V is the dendritic growth velocity, R is the dendritic tip radius, alpha is the liquid thermal diffusivity, and d0 is a capillary length defined in the text. Several dendritic stability models are reviewed and discussed in comparison to the present experimental results.

Huang, S.-C.↗
NASA NTRS1982

Rotor tip clearance effects on overall and blade-element performance of axial-flow transonic fan stage

The effects of tip clearance on the overall and blade-element performance of an axial-flow transonic fan stage are presented. The 50-centimeter-diameter fan was tested at four tip clearances (nonrotating) from 0.061 to 0.178 centimeter. The calculated radial growth of the blades was 0.040 centimeter at design conditions. The decrease in overall stage performance with increasing clearance is attributed to the loss in rotor performance. For the rotor the effects of clearance on performance parameters extended to about 70 percent of blade span from the tip. The stage still margin based on an assumed operating line decreased from 15.3 to 0 percent as the clearance increased from 0.061 to 0.178 centimeter.

Moore, R. D.↗
NASA NTRS1981

Crack tip deformation and fatigue crack growth

Recent research on fatigue crack growth is summarized. Topics discussed include the use of the differential stress intensity factor to characterize crack tip deformation, the use of the unzipping model to study the growth of microcracks and the fatigue crack growth in a ferritic-martensitic steel, and the development of a model of fatige crack growth threshold. It is shown that in the case of small yielding, the differential stress intensity factor provides an adequate description of cyclic plastic deformation at the crack tip and correlates well with the crack growth rate. The unzipping model based on crack tip shear decohesion process is found to be in good agreement with the measured crack growth and striation spacing measurements. The proposed model of crack growth threshold gives correct predictions of the crack growth behavior in the near-threshold region.

Liu, H.-W.↗
NASA NTRS1982

On the opening of premixed Bunsen flame tips

The local extinction of Bunsen flame tip and edges of hydrocarbon/air premixtures has been experimentally investigated using a variety of burners. Results show that, while for both rich propane/air and butane/air mixtures tip opening occurs at a constant fuel equivalence ratio of 1.44 and is therefore independent of the intensity, uniformity, and configuration of the approach flow, for rich methane/air flames burning is intensified at the tip and therefore opening is not possible. These results substantiate the concept and dominance of the diffusional stratification mechanism in causing extinction, and clarify the theoretical predictions on the possible opening of two-dimensional flame wedges.

Law, C. K.↗
NASA NTRS1984

Burner-Injector-Post Tip

Bimetallic tips attached to injector posts improve burner performance and reliability. Tip allows excess heat generated at tip to be dissipated circumferentially and axially through thermal conduction.

Wagner, W. R.↗
NASA NTRS1982

Finite-element analysis of initiation, stable crack growth and instability using a crack-tip-opening displacement criterion

An elastic-plastic (incremental and small strain) finite element analysis was used with a crack growth criterion to study crack initiation, stable crack growth, and instability under monotonic loading to failure of metallic materials. The crack growth criterion was a critical crack-tip-opening displacement (CTOD) at a specified distance from the crack tip, or equivalently, a critical crack-tip-opening angle (CTOA). Whenever the CTOD (or CTOA) equaled or exceeded a critical value, the crack was assumed to grow. Single values of critical CTOD were used in the analysis to model crack initiation, stable crack growth, and instability for 7075-T651 and 2024-T351 aluminum alloy compact specimens. Calculated and experimentally measured CTOD values at initiation agreed well for both aluminum alloys. These critical CTOD values were also used to predict failure loads on center-crack tension specimens and a specially-designed three-hole-crack tension specimen made of the two aluminum alloys and of 304 stainless steel. All specimens were 12.7 mm thick. Predicted failure loads for 7075-T651 aluminum alloy and 304 stainless steel specimens were generally within + or - 15 percent of experimental failure loads, whereas the predicted failure loads for 2024-T351 aluminum alloy specimens were generally within + or - 5 percent of the experimental loads.

Newman, J. C., Jr.↗
NASA NTRS1982

A study of aerodynamic heating distributions on a tip-fin controller installed on a Space Shuttle Orbiter model

The aerodynamic heating of a tip-fin controller mounted on a Space Shuttle Orbiter model was studied experimentally in the Calspan Advanced Technology Center 96 inch Hypersonic Shock Tunnel. A 0.0175 scale model was tested at Mach numbers from 10 to 17.5 at angles of attack typical of a shuttle entry. The study was conducted in two phases. In phase 1 testing a thermographic phosphor technique was used to qualitatively determine the areas of high heat-transfer rates. Based on the results of this phase, the model was instrumented with 40 thin-film resistance thermometers to obtain quantitative measurements of the aerodynamic heating. The results of the phase 2 testing indicate that the highest heating rates, which occur on the leading edge of the tip-fin controller, are very sensitive to angle of attack for alpha or = 30 deg. The shock wave from the leading edge of the orbiter wing impinges on the leading edge of the tip-fin controller resulting in peak values of h/h(Ref) in the range from 1.5 to 2.0. Away from the leading edge, the heat-transfer rates never exceed h/h(Ref) = 0.25 when the control surface, is not deflected. With the control surface deflected 20 deg, the heat-transfer rates had a maximum value of h/h(Ref) = 0.3. The heating rates are quite nonuniform over the outboard surface and are sensitive to angle of attack.

Wittliff, C. E.↗
NASA NTRS1983

Tip clearance flow in a compressor rotor passage at design and off-design conditions

The flow field in the tip clearance region of a compressor rotor at an off-design condition is reported in this paper. The earlier data at the design condition has also been re-interpreted and correlated with the blade and the flow parameters. The measurements inside the rotor tip region are acquired using a miniature hot wire sensor of 'V' configuration. The instantaneous velocity data is analyzed by the ensemble averaging technique to derive the blade-to-blade velocity field at various axial and radial locations between the rotor tip and the casing. The flow and the blade pressure data at the design condition are compared with the data at the off-design condition (lower blade loading). In addition to a reduction in the leakage velocities, its chordwise variation is also altered substantially at the lower blade loading.

Lakshminarayana, B.↗
NASA NTRS1983

Comparison of calculated and measured pressures on straight and swept-tip model rotor blades

Using the quasi-steady, full potential code, ROT22, pressures were calculated on straight and swept tip model helicopter rotor blades at advance ratios of 0.40 and 0.45, and into the transonic tip speed range. The calculated pressures were compared with values measured in the tip regions of the model blades. Good agreement was found over a wide range of azimuth angles when the shocks on the blade were not too strong. However, strong shocks persisted longer than predicted by ROT22 when the blade was in the second quadrant. Since the unsteady flow effects present at high advance ratios primarily affect shock waves, the underprediction of shock strengths is attributed to the simplifying, quasi-steady, assumption made in ROT22.

Tauber, M. E.↗
NASA NTRS1985

Unsteady analysis of rotor blade tip flow

The development of the VSAERO-TS and VSAERO-H computer programs for calculating the unsteady aerodynamic characteristics of arbitrarily shaped wings oscillating in pitch is presented. The effect of several wake parameters on chordwise pressure distribution in VSAERO-TS is given and the convergence characteristics of both programs are discussed. In the program, the influence coefficient for each panel is formulated for a planar surface and so a skewed panel is represented by a projected flat quadrilateral lying in the mean plane. Since panels in the extreme roll-up region of the tip vortex are highly skewed the program was modified to treat each highly skewed panel as a pair of triangles. The programs are validated by comparing the chordwise pressure distribution of several blade tip planforms with experimental data. The comparison, for the most part, is good. The triangular panel representation improved the chordwise pressure distribution near the tip region for higher mean angle of attack.

Maskey, B.↗
NASA NTRS1985

Oxidizing seal for a turbine tip gas path

The sealing of the gas path in a gas turbine engine at the blade tips is improved by maintaining a minimum clearance between the rotor blade tips and the gas path seal. This is accomplished by taking advantage of an increase in volume during controlled oxidation of certain intermetallic compounds which have high melting points. The increase in volume closes the clearance subsequent to a rub between the blades and the seal. Thus, these compounds re-form the tip seal surface to assure continued engine efficiency.

Cawley, J. D.↗
NASA NTRS1985

Reflection plane tests of a wind turbine blade tip section with ailerons

Tests were conducted in the NASA Langley 30 by 60 foot Wind Tunnel on a full scale 7.31 m (24 ft) long tip section of a wind turbine rotor blade. The blade tip section was built with ailerons on the trailing edge. The ailerons, which spanned a length of 6.1 m (20 ft), were designed so that two types could be evaluated: the plain and the balanced. The ailerons were hinged on the suction surface at the 0.62 X chord station behind the leading edge. The purpose of the tests was to measure the aerodynamic characteristics of the blade section for: an angle of attack range from 0 deg to 90 deg aileron deflections from 0 deg to -90 deg, and Reynolds numbers of 0.79 and 1.5 x 10 to the 6th power. These data were then used to determine which aileron configuration had the most desirable rotor control and aerodynamic braking characteristics. Tests were also run to determine the effects of vortex generators, leading edge roughness, and the gaps between the aileron sections on the lift, drag, and chordwise force coefficients of the blade tip section.

Savino, J. M.↗
NASA NTRS1984

Airfoil tip vortex formation noise

Spectral data are presented for the noise produced due to the turbulent three-dimensional vortex flow existing near the rounded tip of lifting airfoils. The results are obtained by the comparison of sets of two- and three-dimensional test data for different airfoil model sizes, angles of attack, and tunnel flow velocities. Microphone cross-correlation and cross-spectral methods were used to determine the radiated noise. Corrections were made for tunnel shear layer and source directivity effects. Interpretation of the results are aided by a three-dimensional flow analysis developed for this study which determines open tunnel and finite aspect ratio corrections heretofore neglected in tip vortex studies. Hot wire measurements were made in the tip vortex formation region for the specification of governing flow parameters. The spectral data is normalized in a format considered most useful for subsequent quantitative prediction of this noise mechanism for practical systems such as helicopter rotors. Comparison is made to the analysis of George and Chou. A recommended prediction method is given.

Brooks, T. F.↗
NASA NTRS1983

An experimental investigation and numerical prediction of thermomechanical phenomena in high speed rotor tip rubbing

A thermomechanical study of the intermittent rubbing of a rotor blade tip and a casing seal is carried out taking into account the existence of thermal contact resistance. The effect of the thermal properties of a plasma sprayed coating on the blade tip is studied. The influence of a variable heat generation and variable thermal contact resistance at the blade tip as it passes along the path of rubbing is also discussed.

Emery, A. F.↗