Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Thrust”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

Study aids accuracy of turbopump axial thrust analysis

Test program to verify theory used in calculating axial thrust uses turbopump instrumented with /a/ proximity transducers for measuring shaft position, /b/ a strain gage thrust bearing carrier to measure axial thrust, and /c/ internal pressure taps to define component pressure gradients used in thrust calculations.

Nielson, C. E.↗

Estimates of trapped radiation encountered on low-thrust trajectories through the Van Allen belts

Estimates were made of the number of trapped protons and electrons encountered by vehicles on low-thrust trajectories through the Van Allen belts. The estimates serve as a first step in assessing whether these radiations present a problem to on-board sensitive components and payload. The integrated proton spectra and electron spectra are presented for the case of a trajectory described by a vehicle with a constant-thrust acceleration A sub c equal to 0.001 meter/sq sec. This value of acceleration corresponds to a trip time of about 54 days from low earth orbit to synchronous orbit. It is shown that the time spent in the belts and hence the radiation encountered vary nearly inversely with the value of thrust acceleration. Thus, the integrated spectral values presented for the case of A sub c = 0.001 meter/sq sec can be generalized for any other value of thrust acceleration by multiplying them by the factor 0.001/A sub c.

Karp, I. M.↗

Aerodynamic characteristics of a vectored-thrust V/STOL fighter in the transition speed range

A wind-tunnel investigation was conducted with a vectored-thrust V/STOL fighter configuration. The model was equipped with two nacelle-mounted vectored-thrust jet simulators and one lift-jet simulator. The vectored-thrust jet could be tested at two alternate longitudinal positions and three nozzle deflection angles. The vectored-thrust configuration with the rear nozzles showed an increase in lift and a decrease in pitching moment when compared with the forward nozzles. The rear nozzles also improve stall characteristics.

Mineck, R. E.↗

Geometric factors affecting noise suppresion and thrust loss of divergent-lobe supersonic jet noise suppressor

The thrust loss and noise suppression of a divergent-lobe supersonic jet noise suppressor were experimentally determined over a range of nozzle pressure ratios of 1.5 to 4.0. These small-scale cold flow tests were made to determine the effect on thrust and noise of: suppressor length, rearward facing step height, suppressor divergence angle, and ejector shroud length and location. Noise suppression was achieved at nozzle pressure ratios of 2.5 and greater. Maximum lobe jet noise attenuation of 15 db with thrust loss differences of 1.5 percent compared to the convergent nozzle were obtained at a nozzle pressure ratio of 3.5 with an ejector shroud two nozzle diameters long. Without the ejector the attenuation was 13 db with thrust loss differences of 11 percent. Short suppressors approximately one primary nozzle throat diameter long performed as well as longer suppressors. Rearward facing step height had a significant effect on noise suppression. Ejector shrouds two nozzle diameters in length are feasible.

Huff, R. G.↗

Test stand for precise measurement of impulse and thrust vector of small attitude control jets

A test stand which accurately measures the impulse bit and thrust vector of reaction jet thrusters used in the attitude control system of space vehicles has been developed. It can be used to measure, in a vacuum or ambient environment, both impulse and thrust vector of reaction jet thrusters using hydrazine or inert gas propellants. The ballistic pendulum configuration was selected because of its accuracy, simplicity, and versatility. The pendulum is mounted on flexure pivots rotating about a vertical axis at the center of its mass. The test stand has the following measurement capabilities: impulse of 0.00004 to 4.4 N-sec (0.00001 to 1.0 lb-sec) with a pulse duration of 0.5 msec to 1 sec; static thrust of 0.22 to 22 N (0.05 to 5 lb) with a 5 percent resolution; and thrust angle alinement of 0.22 to 22 N (0.05 to 5 lb) thrusters with 0.01 deg accuracy.

Woodruff, J. R.↗

Constrained low-thrust guidance.

Constrained low thrust guidance algorithms for three axis and spin-stabilized, constant power, solar electric propelled spacecraft on fixed time rendezvous missions are developed. A 'bang-bang' type of minimum-propellant thrust program is used. Control constraints arise from the specification that the thrust vector must remain fixed relative to the solar panels. The guidance law is derived from deterministic linear perturbation theory and is controllable to first order on trajectories containing at least two thrust arcs. The number and timing of guidance updates and the effectiveness of the guidance law in compensating for state and control estimation biases and uncertainties are discussed. Numerical comparisons between the optimal control and the restricted control case are presented on a Encke comet rendezvous.

Ungs, M. J.↗

A users manual for a computer program which calculates time optical geocentric transfers using solar or nuclear electric and high thrust propulsion

This manual is a guide for using a computer program which calculates time optimal trajectories for high-and low-thrust geocentric transfers. Either SEP or NEP may be assumed and a one or two impulse, fixed total delta V, initial high thrust phase may be included. Also a single impulse of specified delta V may be included after the low thrust state. The low thrust phase utilizes equinoctial orbital elements to avoid the classical singularities and Kryloff-Boguliuboff averaging to help insure more rapid computation time. The program is written in FORTRAN 4 in double precision for use on an IBM 360 computer. The manual includes a description of the problem treated, input/output information, examples of runs, and source code listings.

Sackett, L. L.↗

Static performance and noise tests on a thrust reverser for an augmentor wing aircraft

A 1/3 scale model static test program was conducted to measure the noise levels and reverse thrust performance characteristics of wing-mounted thrust reverser that could be used on an advanced augmentor wing airplane. The configuration tested represents only the most fundamental designs where installation and packaging restraints are not considered. The thrust reverser performance is presented in terms of horizontal, vertical, and resultant effectiveness ratios and the reverser noise is compared on the basis of peak perceived noise level (PNL) and one-third octave band data (OASPL). From an analysis of the model force and acoustic data, an assessment is made on the stopping distance versus noise for a 90,900 kg (200,000 lb) airplane using this type of thrust reverser.

Harkonen, D. L.↗

Solar electric propulsion thrust beam interactive effects

Interactive effects between ion engine thrust beams and an SEP spacecraft and its science payload have been examined. AC electric contamination from thrust beam potential fluctuations of both 'common mode' and 'point-to-point' forms has been evaluated. Quenching of point-to-point E-fields by both thrust ion and charge exchange ion plasmas is expected. Reduction methods for AC electric contamination from common mode thrust beam potential fluctuations have been developed. Charged particle contamination of ambient space and plasma wave contamination may result from density magnitude and spatial extent of charge exchange plasma plumes. Reduction methods for cone of directions of high angle charge exchange ions have been examined.

Sellen, J. M., Jr.↗

Tailoff thrust and impulse imbalance between pairs of Space Shuttle solid rocket motors

The tailoff thrust and impulse imbalance between pairs of solid rocket motors is of particular interest for the Space Shuttle Vehicle because of the potential control problems that exist with this asymmetric configuration. Although a similar arrangement of solid rocket motors was utilized for the Titan Program, they produced less than one-half the thrust level of the Space Shuttle at web action time, and the overall vehicle was symmetric. Since the Titan Program does provide the most applicable actual test data, 23 flight pairs were analyzed to determine the actual tailoff thrust and impulse imbalance experienced. The results were scaled up using the predicted web action time thrust and tailoff time to arrive at values for the Space Shuttle. These values were then statistically treated to obtain a prediction of the maximum imbalance one could expect to experience during the Shuttle Program.

Jacobs, E. P.↗

Thrust vector control by liquid injection for solid propellant rockets

In liquid injection thrust vector control, a rocket jet is deflected for steering purposed by injecting a liquid into the nozzle exit cone. The liquid is preferably both dense and reactive so that it adds mass and energy and generates shocks in the supersonic exhaust. This behavior increases thrust in the affected part of the jet producing not only a side force for steering but an addition to axial thrust. This paper presents a summary of current liquid injection thrust vector control technology, including procedures for design, development, analysis, testing and evaluation, together with supporting data and references.

Zeamer, R. J.↗

Vector thrust induced lift effects for several ejector exhaust locations on a V/STOL wind tunnel model at forward speed

The results and analysis of aerodynamic force data obtained from a small scale model of a V/STOL research vehicle in a low speed wind tunnel are presented. The analysis of the data includes the evaluation of aerodynamic-propulsive lift performance when operating twin ejector nozzles with thrust deflected. Three different types of thrust deflector systems were examined: 90 deg downward deflected nozzle, 90 deg slotted nozzle with boundary layer control, and an externally blown flap configuration. Several nozzle locations were tested, including over and underwing positions. The interference lift of the nacelle and model due to jet exhaust thrust is compared and results show that 90 deg turned nozzles located over the wing (near the trailing edge) produce the largest interference lift increment for an untrimmed aircraft, and that the slotted nozzle located under the wing near the trailing edge (in conjunction with a BLC flap) gives a comparable interference lift in the trimmed condition. The externally blown flap nozzle produced the least interference lift and significantly less total lift due to jet thrust effects.

Sharon, A. D.↗

Three dimensional thrust chamber life prediction

A study was performed to analytically determine the cyclic thermomechanical behavior and fatigue life of three configurations of a Plug Nozzle Thrust Chamber. This thrust chamber is a test model which represents the current trend in nozzle design calling for high performance coupled with weight and volume limitations as well as extended life for reusability. The study involved the use of different materials and material combinations to evaluate their application to the problem of low-cycle fatigue in the thrust chamber. The thermal and structural analyses were carried out on a three-dimensional basis. Results are presented which show plots of continuous temperature histories and temperature distributions at selected times during the operating cycle of the thrust chamber. Computed structural data show critical regions for low-cycle fatigue and the histories of strain within the regions for each operation cycle.

Armstrong, W. H.↗

Space shuttle orbit maneuvering engine reusable thrust chamber program

The feasibility of potential reusable thrust chamber concepts is studied. Propellant condidates were examined and analytically combined with potential cooling schemes. A data base of engine data which would assist in a configuration selection was produced. The data base verification was performed by the demonstration of a thrust chamber of a selected coolant scheme design. A full scale insulated columbium thrust chamber was used for propellant coolant configurations. Combustion stability of the injectors and a reduced size thrust chamber were experimentally verified as proof of concept demonstrations of the design and study results.

Senneff, J. M.↗

Monte Carlo investigation of thrust imbalance of solid rocket motor pairs

The Monte Carlo method of statistical analysis is used to investigate the theoretical thrust imbalance of pairs of solid rocket motors (SRMs) firing in parallel. Sets of the significant variables are selected using a random sampling technique and the imbalance calculated for a large number of motor pairs using a simplified, but comprehensive, model of the internal ballistics. The treatment of burning surface geometry allows for the variations in the ovality and alignment of the motor case and mandrel as well as those arising from differences in the basic size dimensions and propellant properties. The analysis is used to predict the thrust-time characteristics of 130 randomly selected pairs of Titan IIIC SRMs. A statistical comparison of the results with test data for 20 pairs shows the theory underpredicts the standard deviation in maximum thrust imbalance by 20% with variability in burning times matched within 2%. The range in thrust imbalance of Space Shuttle type SRM pairs is also estimated using applicable tolerances and variabilities and a correction factor based on the Titan IIIC analysis.

Sforzini, R. H.↗

The aerodynamic and acoustic characteristics of an over-the-wing target-type thrust reverser model

A static test of a large-scale, over-the-wing (OTW) powered-lift model was performed. The OTW propulsion system had been modified to incorporate a simple target-type thrust reverser as well as the normal rectangular OTW exhaust nozzle. Tests were performed in both the reverse thrust and approach configurations. The thrust reverser noise created by jet turbulence mixing and the OTW approach noise were both low frequency and broadband. When scaled to a 45,400-kg (100,000-lb) aircraft, the thrust reverser and approach configurations produced peak 152-m (500-ft) sideline perceived noise levels of 110 and 105 PNdB, respectively. The aerodynamic performance of the model showed that 50% or greater reverser effectiveness can be achieved without experiencing ingestion of exhaust gas or ground debris into the engine inlets.

Falarski, M. D.↗

Variation of pitching moment with engine thrust for a twin-engine commercial jet aircraft

Flight tests were made to determine the effect of engine net thrust on airplane pitching moment for a twin-engine commercial jet transport in the approach, climbout and descent, and cruise configurations. The results indicate that for all the conditions analyzed, the pitching moment due to thrust is somewhat higher than that estimated from the product of net thrust and its moment arm (perpendicular distance from thrust axis to the airplane center of gravity). The differences are attributed to additional moments produced by nacelle normal force, jet-induced downwash, and interaction between wing flow and engine nacelle flow.

Shanks, R. E.↗

A lifting surface theory for thrust augmenting ejectors

The circulation theory of airfoil lift has been applied to calculate the performance of thrust augmenting ejectors. The ejector shroud is considered to be 'flying' in the secondary velocity field induced by the entrainment of the primary jet, so that the augmenting thrust is viewed as analogous to the lift on an airfoil. Vortex lattice methods are utilized to compute the thrust augmentation from the force on the flaps. The augmentation is shown to be a function of the length and shape of the flaps, as well as their position and orientation. Predictions of this new theory are compared with the results of classical methods of calculating the augmentation by integration of the stream thrust.

Bevilaqua, P. M.↗