Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Tensile testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Diffusion bonded compact heat exchanger in Inconel 740H for high temperature and high-pressure applications

It is desired to develop heat exchangers able to be operated at high temperatures (750˚C) and pressures (3636 psi) for use in advanced Brayton power cycle. Conventional materials have not had the high strength at temperature required for these applications previously, however a fairly new material Inconel 740H developed by Special Metals for the ultra-supercritical water fossil industry has shown good performance under these conditions. In further efforts to capitalize on these new high strength high temperature alloys CompRex has developed a diffusion bonding procedure capable of alloying compact high effectiveness heat exchangers that can perform under these high temperature and high-pressure conditions. Initial tests of the heat exchanger are being conducted at the University of Wisconsin using supercritical CO2 working fluid. The bonding process has been adjusted such that the strength of the bonded block has achieved over 90% yield and tensile strength of the 740H base material values. Grain size before and after bonding were measured to determine the extent of grain growth and grain diffusion across the interface. A discussion of the heat exchanger design, etching and initial tensile tests on sample bonds will be discussed.

14 SOLAR ENERGY↗
DOE OSTI2020

Technical Qualification of New Materials for High Efficiency Coal-Fired Boilers and Other Advanced FE Concepts: Haynes® 282® ASME Boiler and Pressure Vessel Code Case

This DOE Fossil Energy project, FEAA117, addressed materials issues relevant to qualifying and deploying a Ni-base alloy for a new application in an advanced ultra-supercritical coal-fired boiler. The goal was the deployment of Haynes International alloy Haynes® 282® for applications in superheaters, reheaters, and steam delivery pipes, by completing base metal, cross-weld and all-weld metal mechanical testing needed for an ASME Boiler and Pressure Vessel Code Case and the associated microstructural analyses needed for assurance of boiler-relevant lifetimes. The alloy also is of interest for other applications including supercritical CO₂ power generation cycles. Tensile testing was completed from 20°-927°C on the three base metal alloy 282 heats, two sets of cross-weld specimens and all weld metal specimens. A total of 148 creep tests with over 565,000 h of cumulative testing was completed on base metal, cross-weld and all weld metal specimens. This project was performed with cost share from Haynes International.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2020

Status of INL Aged A709 Mechanical Testing

A709 was selected to be qualified in Section III, Division 5 of the American Society of Mechanical Engineers Boiler and Pressure Vessel Code. Idaho National Laboratory (INL), Argonne National Laboratory and Oak Ridge National Laboratory are collaborating to develop and qualify A709 plate. Aging A709 to form beneficial precipitates prior to service is investigated. One tensile test, five creep-rupture tests, and eight cyclic tests have been completed on aged A709. Two creep-rupture tests are in progress.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

A Multicontinuum-Theory-Based Approach to the Analysis of Fiber-Reinforced Polymer Composites with Degraded Stiffness and Strength Properties Due to Moisture Absorption

Marine energy generation technologies such as wave and tidal power have great potential in meeting the need for renewable energy in the years ahead. Yet, many challenges remain associated with marine-based systems because of the corrosive environment. Conventional materials like metals are subject to rapid corrosive breakdown, crippling the lifespan of structures in such environments. Fiber-reinforced polymer composites offer an appealing alternative in their strength and corrosion resistance, but can experience degradation of mechanical properties as a result of moisture absorption. An investigation is conducted to test the application of a technique for micromechanical analysis of composites, known as multicontinuum theory and demonstrated in past works, as a mechanism for predicting the effects of prolonged moisture absorption on the performance of fiber-reinforced composites. Experimental tensile tests are performed on composite coupons with and without prolonged exposure to a salt water solution to obtain stiffness and strength properties. Multicontinuum theory is applied in conjunction with micromechanical modeling to deduce the effects of moisture absorption on the behavior of constituent materials within the composites. The results are consistent with experimental observations when guided by known mechanisms and trends from previous studies, indicating multicontinuum theory as a potentially effective tool in predicting the long-term performance of composites in marine environments.

36 MATERIALS SCIENCE↗
DOE OSTI2021

DEM analysis of the effect of interface transition zone on dynamic splitting tensile behavior of high-strength concrete based on multi-phase model

Highlights: • Crushable aggregates with the real geometry shape are generated by using clump-cluster method. • Flat-Joint Model is adopted as the constitutive law. • The tensile strength is almost not affected by ITZ strength when its strength exceeds 0.8 times that of mortar. • A modified formula that can reflect the functional relationship between the ITZ strength and the TDIF is proposed. The tensile strength is one of the main parameters in the design of concrete structures and has an important influence on the cracking performance and durability of concrete materials. As the weak region in concrete, the strength of the interface transition zone (ITZ) directly affects the dynamic mechanical response of concrete. Meanwhile, considering that the tensile performance of concrete is far weaker than its compressive performance, the study of the strength of ITZ is of great significance to the dynamic tensile fracture characteristics and mechanical properties of concrete. In this paper, a method combining 3D scanning technology and Clump-Cluster was proposed to generate a real geometry shape model of crushable aggregate. On this basis, the 3D discrete element model (DEM) of high-strength concrete was constructed using the Flat-Joint Model (FJM). The effects of the ITZ strength on the failure mode, number of microcracks, tensile strength and strain rate effect of high-strength concrete under strain rates from 0.01/s to 100/s were studied by splitting tensile test. The simulation results indicate that the number of microcracks generated decreases with the increase of ITZ strength, and the proportion of ITZ cracks decreases obviously. When the ITZ strength exceeds the critical value of 0.8 times that of mortar, the tensile strength is almost not affected by ITZ strength. In addition, based on the numerical simulation results, a modified formula that can reflect the functional relationship between the ITZ strength and the dynamic increasing factor of the concrete tensile strength (TDIF) is proposed, and the rationality of the TDIF modified formula is verified.

36 MATERIALS SCIENCE↗
DOE OSTI2021

A machine learning aided interpretable model for rupture strength prediction in Fe-based martensitic and austenitic alloys

Abstract The class of 9–12% Cr ferritic-martensitic alloys (FMA) and austenitic stainless steels have received considerable attention due to their numerous applications in high temperature power generation industries. To design high strength steels with prolonged service life requires a thorough understanding of the long-term properties, e.g., creep rupture strength, rupture life, etc., as a function of the chemical composition and processing parameters that govern the microstructural characteristics. In this article, the creep rupture strength of both 9–12% Cr FMA and austenitic stainless steel has been parameterized using curated experimental datasets with a gradient boosting machine. The trained model has been cross validated against unseen test data and achieved high predictive performance in terms of correlation coefficient ( $$R^{2} > 0.98 $$ R 2 > 0.98 for 9–12% Cr FMA and $$R^{2} > 0.95 $$ R 2 > 0.95 for austenitic stainless steel) thus bypassing the need for additional comprehensive tensile test campaigns or physical theoretical calculations. Furthermore, the feature importance has been computed using the Shapley value analysis to understand the complex interplay of different features.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Parametric Finite Element Analysis of Naturally Corroded Steel Specimens Using 3D Surface Laser Scans

Corrosion is considered a uniform thickness reduction design guideline of the maritime industry. However, additionally, the corroded and irregular morphology of the surface affects the steel's load-bearing capacity and its impact on the strength and elongation behaviour of the steel is not yet fully understood. These effects on the local behaviour of steel structures under tensile loading were investigated with tensile tests on naturally corroded steel specimens and nonlinear finite element simulations including the corroded surface morphology with a uniform surface idealation. The models also include the deformed specimen shape. The developed approach led to highly accurate parametric finite element models predicting the ultimate tensile strength and longitudinal position of fracture. The results show that all included aspects are essential for accurate simulations, while solely the maximum available surface resolution was not as decisive.

corrosion↗
DOE OSTI2025

PROCESS-STRUCTURE-PROPERTY RELATIONSHIPS IN LASER POWDER BED FUSION PRODUCED 17-4 PH STEEL

Laser powder bed fusion (LPBF) is a metal additive manufacturing method that produces non-traditional microstructures as a result of the rapid solidification and thermal cycling inherent to the process. When using LPBF-produced material in application, these unique microstructures challenge the applicability of well developed mechanical property databases achieved by conventional heat treatments. For wider adoption of this technology, a more holistic understanding is necessary on how process attributes develop material structure, which dictate mechanical properties. This dissertation explores the process– structure–property relationships in LPBF 17-4 PH steel through systematic evaluation of atmospheric processing and heat treatment effects on microstructure and mechanical performance. Specimens were fabricated under controlled build environments, subjected to a range of solutionizing, homogenizing, and aging treatments, and characterized using optical microscopy, electron back scatter diffraction (EBSD), and X-ray diffraction (XRD) to quantify phase evolution. Tensile testing was performed to directly link heat treatment pathway and nitrogen absorption to mechanical performance. This work demonstrates where conventional heat treatment standards are applicable to LPBF 17-4 PH steel and where modifications are required. By directly correlating phase stability, nitrogen effects, and tensile response, this work provides practical guidelines for tailoring post-processing strategies. These findings underscore that successful application of LPBF 17-4 PH steel requires explicit consideration of both build environment and post-processing. By linking processing conditions to microstructure and performance, this work advances understanding of critical variables that govern reliability of additively manufactured precipitation-hardened stainless steels in demanding applications.

Brown, Benjamin [Kansas City National Security Cam↗
DOE OSTI2025

Production of Creep-Resistant FeCrAl-ODS

Four ODS FeCrAl alloys with base alloy composition Fe-16Cr-4Al-2Mo-0.2Y (wt.%) were mechanically alloyed with minor additions of CeO 2 and Y 2 O 3 additions and were successfully extruded into rectangular-shaped bars. Two oxide compositions were explored, which were designated NC with oxide addition of 0.5CeO 2 plus 0.2Yin solution of the base alloy powder and PC with additions of 0.5CeO 2 and 0.7Y 2 O 3 to elevate the O level. The microstructure of both alloys revealed by SEM and EBSD to consist of very small grains with sizes of ~450-520 nm and weak texture components. Sub-size tensile specimens fabricated from both alloys were tensile tested from room temperature to 800ºC. The results for both alloys from room temperature to 400ºC showed very high strengths, but low ductilities, especially uniform strain. From 500ºC to 800ºC, the strengths decreased rapidly, and the ductilities increased significantly. The reason for the rapid decreases in tensile strengths above 500ºC for both alloys is not clear, but will require advanced characterization techniques including atom probe tomography, to determine the size and number density of the nano-size oxide particles, and TEM/EFTEM, for investigating the dispersion of nano-size oxide particles on grain boundaries to assess the Zener grain boundary pinning effect, which will hinder grain coarsening at high temperatures that may enhance the Hall Petch strengthening mechanism.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Mechanical and Tribological Performance of Additively Manufactured Nanocrystalline Aluminum via Cryomilling and Cold Spray

In this study, nanocrystalline (NC) aluminum (Al) and magnesium (Mg)-doped Al bulk components were fabricated using a hybrid manufacturing process that combines cryomilling and high-pressure cold spray (HPCS) additive deposition techniques. Yttria-stabilized zirconia (YSZ) was also added during the HPCS process to improve deposition efficiency and build-up thickness via peening. The evolution of morphology, crystallite size, and elemental composition of both cryomilled powders and cold-sprayed (CS’ed) components was systematically characterized using X-ray Diffraction (XRD), Scanning Electron Microscopy (SEM), and Transmission Electron Microscopy (TEM). Mechanical characterization was performed using Vickers microhardness and uniaxial tensile testing, while the tribological behavior was assessed using sliding wear tests under dry/lubricated conditions. XRD analysis revealed that increased cryomilling duration led to significant crystallite refinement, which directly correlated with enhanced hardness and strength. This mechanical strengthening was accompanied by an increase in coefficient of friction (COF) and lower wear rates. The results also showed that the Mg-doped Al exhibited superior hardness, tensile strength, and tribological performance compared to pure Al. The study further explores the underlying mechanisms responsible for these enhancements, highlighting the potential of solute-assisted grain boundary stabilization in tailoring high-performance NC Al alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Influence of Shear Strength Assumptions on BISON Debonding Simulations

Accurately predicting the thermomechanical response of buffer–IPyC debonding in TRISO fuel particles requires reliable mechanical property inputs for each coating layer, particularly the normal and shear strengths that influence interlayer delamination and stress concentrations. Micro tensile testing of AGR-2 fuel particles provided experimentally measured normal strengths for the buffer, IPyC, and buffer–IPyC interface; however, shear strength was not measured. As a result, BISON simulations of interface debonding must rely on assumed shear strength values, typically estimated as 20–40% of the measured ultimate tensile strength. This study evaluates how these assumed shear strength values influence cohesive zone model (CZM) predictions of buffer–IPyC separation in AGR 2 TRISO particles. Using micro tensile data from three AGR 2 compacts (2 1 3, 5 1 3, and 6 3 3), BISON simulations were performed with multiple shear strength assumptions to quantify their effect on radial and tangential stress evolution, debonding, and gap propagation. The results show that shear strength is a high sensitivity parameter: increasing the assumed shear strength significantly alters the stress distribution at the buffer–IPyC junction, shifts the predicted debonding location, and changes the extent of partial gap formation. While normal strength controls the initiation of interface separation, shear strength strongly influences the mode mixity of the failure process and the resulting stress concentrations transmitted to the IPyC and SiC layers. These findings highlight a critical gap in current TRISO mechanical characterization. Without experimentally measured shear strength, BISON simulations must rely on approximations that introduce uncertainty into predictions of coating layer integrity and fission product barrier performance. Future fuel qualification campaigns should therefore consider measurement of shear strength at the interlayer interfaces to reduce model uncertainty and improve the fidelity of TRISO fuel performance simulations.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

High Temperature High Vacuum Mechanical Property Assessment of Zirconium Nuclear Fuel Cladding

This report presents the mechanical characterization of a specific Zry-4 cladding batch serving as the foundation for a diverse range of fuel performance research at Oak Ridge National Laboratory (ORNL). This effort supports research needs for the U.S. Department of Energy (DOE), particularly regarding evaluating accident tolerant fuel (ATF) cladding coating concepts, expanding understanding of cladding response to loss-of-coolant accidents (LOCA) transients, refining post-critical heat flux (CHF) limits (t@T), and upcoming irradiation campaigns. The central objective was to define the baseline performance of the substrate Zircaloy-4 (Zry-4) material leveraged across ORNL Advanced Fuel Campaign (AFC) efforts through controlled high-temperature vacuum tensile testing. This work begins to address gaps in existing models where implementation based on nominal heat-treatment labels, such as stress relief annealed (SRA), often fail to capture the interplay of recovery, recrystallization, and grain growth. To quantify this, data was benchmarked against the Pacific Northwest National Laboratory (PNNL) stress strain model to determine where this material falls in comparison to assumed values for materials in the same heat treatment regime. Analysis of the tensile data revealed that this specific SRA batch exhibits a transitional microstructural state best described by an effective cold-work (CW) parameter of 0.09, diverging from the previous estimation of 0.5 for SRA materials. Additionally, comparative testing of Cr coated specimens demonstrated no distinct difference in axial strength relative to the bare substrate. This suggests that the strengthening benefits of Cr coatings observed in burst scenarios are driven by residual stress mechanisms acting solely in the hoop direction.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Chemically Recyclable Polyester Thermosets from Activated Adipic Acid and Renewable Polyols

This study outlines a method for producing chemically recyclable crosslinked polyesters using renewable polyols-glycerol and sorbitol-combined with adipic acid (AA), which is transformed/activated into a polyanhydride mixture prior to use. A three-step procedure has been designed: 1) an acid-catalyzed reaction of AA with nontoxic isopropenyl acetate or acetic anhydride to form a crosslinking mixture (CLM) made of adipic-acetic mixed polyanhydrides; 2) a solvent- and additive-free process where glycerol or sorbitol, or a combination thereof, is reacted with the CLM to achieve a prepolymer, and 3) a casting/molding of the liquid viscous prepolymer to yield a thermoset as the end product. Different thermosets (eight examples) are prepared by changing the reagents ratio. These solids are thoroughly characterized by tensile tests, DMA, high-resolution magic angle spinning and solid-state NMR, thermal gravimetric analysis, DSC, and fourier transformed infra red (FT-IR) spectroscopy. The formation of cross-linked polyesters is confirmed in all cases, but mechanical properties varied significantly from one specimen to another. Interestingly, a tensile strength up to 18 MPa-approximately an order of magnitude higher than similar polymers-is achieved when sorbitol and the CLM are used in a 1:1 wt% ratio. The chemical recycle of the resulting polymers is achieved via methanolysis with quantitative recovery of the monomeric units.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Mechanical Properties of Additively Manufactured 316L Stainless Steel Before and After Neutron Irradiation–FY23

This report presents the observed mechanical behavior of the additively manufactured (AM) 316L stainless steel (SS) before and after neutron irradiation. In the Advanced Materials and Manufacturing Technologies (AMMT) program, a variety of mechanical and physical property data are generated and accumulated to assess the AM austenitic alloy for nuclear reactor applications. The testing and evaluation task in the FY 2023 focused on elucidating the effects of sampling location and build size on the mechanical properties of AM 316L SS (in stress-relieved condition) before and after neutron irradiation. The laser powder bed fusion (LPBF) process produced 316L plates of three distinct sizes from which SS-J3 miniature tensile specimens were machined from six different locations. The tensile specimens were irradiated in the High Flux Isotope Reactor (HFIR) normally to 2 and 10 dpa at the target temperatures of 300 °C and 600 °C. Post-irradiation tensile testing was performed at room temperature, 300 °C, and 600 °C. The mechanical properties of AM 316L SS were significantly influenced by the characteristic microstructures of printed materials, which include fine grains and high-density dislocations. Compared with the traditional 316L SS, AM 316L showed higher initial strength and lower ductility. Regardless of sampling location, the AM 316L steel retained relatively high strength and ductility to the highest irradiation dose. A prompt necking at yield (with little uniform ductility) was observed after irradiation at 300 °C but no embrittlement was observed up to 10 dpa. Ductilization by irradiation–the radiation-induced increase of ductility–was observed for the 600 °C irradiation only and it occurred in low dose range only. The neutron irradiation increased the data variation in many tensile property datasets, particularly after 600 °C irradiation, and no clear dependence of tensile properties on build thickness or sampling location was observed.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Interaction of beryllium with 316H stainless steel in molten Li 2 BeF 4 (FLiBe)

The increased demand in renewable energy resources has led to a renewed interest in nuclear reactors including a new generation of molten salt reactors. One of the issues encountered in handling of molten chloride or fluoride salts is the inability of metals to form and retain a protective oxide surface layer, generally chromium oxide. The low chromium content, nickel-based alloy INOR-8, later marketed as Hastelloy N, was specifically developed to contain molten fluorides. This alloy had some deficiencies, but its composition resulted in it incurring far less chromium depletion by the molten fluoride salts than alloys like 316 stainless steel. For the next generation of molten salt reactors, an alloy with pressure vessel code approval and higher temperature capability than Hastelloy N is required. Consequently, several reactor designers have reportedly chosen to build the reactor containment vessel from 316H stainless steel. In order to minimize corrosion of the stainless steel by the molten fluoride salt (2LiF-BeF 2 ), it is proposed to add beryllium metal to the salt to react with impurities and provide a means to lower the oxidation potential thus making the salt less corrosive. Even so, there is a concern whether the beryllium would react with components of the stainless steel. To address this concern, static capsule tests were conducted in which selected amounts of beryllium were added to capsules containing 2LiF-BeF 2 (FLiBe) salt and 316H stainless steel and Hastelloy N samples. Following exposure, the samples were cleaned and examined using a variety of analysis techniques including, optical microscopy, SEM-EDS, XPS, LIBS, XRD and EPMA. Tensile samples were also exposed in capsules, and those were subjected to tensile testing. Notably, It was found that for the level of beryllium additions used in this study, intermetallic compounds were formed which could be detrimental to the long-term performance of the 316H stainless steel.

36 MATERIALS SCIENCE↗
DOE OSTI2023

A Summary of the Microstructural Characterization Results for the A709 Commercial Heats

To improve high temperature strength for advanced nuclear reactors, it is necessary to qualify additional structural materials for introduction into the American Society of Mechanical Engineers (AMSE) Boiler and Pressure Vessel Code (BPVC). Specifically, Alloy 709 was identified as a material for Sodium-cooled Fast Reactors to enhance time-dependent mechanical properties compared to 316H stainless steel, a code qualified high temperature alloy. Idaho National Laboratory (INL) and Oak Ridge National Laboratory (ORNL) performed initial microstructure and mechanical property testing on a third, commercial heat of Alloy 709 stainless steel. The Alloy 709 plate was produced by Allegheny Technology Inc. (ATI) and in the solution annealed condition. The chemical composition was within the limits for an American Society of Testing and Materials (ASTM) A213 specification for seamless tube for material UNS S31025. Grain size was measured as an average ASTM size of 6.5, which was larger than the ASTM 7 required according to ASTM A213 for seamless tube. The chemical composition was within the limits for an ASTM A213, and the room temperature tensile tests and hardness data met ASTM A213 specifications. Creep-fatigue results showed similar behavior to previous heats of Alloy 709.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

Impact of nitrogen on lithium-induced corrosion and cracking of RAFM steel

The emergence of private fusion enterprises, combined with advancements in U.S. and EU ITER-TBM as well as EU DEMO liquid breeder blanket concepts, has renewed focus on the materials challenges. This study examines the compatibility of reduced activation ferritic/martensitic (RAFM) steel in liquid Lithium (Li) containing various Nitrogen (N) concentrations, tested at 600 and 700 °C for 500 and 1000 h under static conditions. Microstructural characterization revealed the corrosion-induced dissolution and precipitation in Li containing 0.082 and 0.17 wt.% N at 600 °C, while limited dissolution and precipitation were observed in N-gettered Li using zirconium (Zr) and titanium (Ti) foils at 600 °C. Tensile testing at room temperature after Li exposure revealed a decrease in strength and ductility of the RAFM steel as a function of N content in Li. Severe embrittlement was observed after 500 h in Li containing 0.17 wt.% N at 600 °C and after 500 h in hot-gettered Li at 700 °C. Chromium (Cr) depletion from the steel matrix was observed, leading to the formation of M6C-type carbides on the surface identified by electron microscopy (SEM), X-ray diffraction (XRD), in agreement with thermodynamic calculations. These findings highlight the critical materials challenges posed by liquid Li breeder blanket concepts, emphasizing the need for improved strategies to address Li-induced dissolution, precipitation, and steel embrittlement due to N contamination of the coolant.

Romedenne, Marie [ORNL] (ORCID:0000000317936561)↗
DOE OSTI2021

P- and S-Wave velocity and Indirect Tensile Measurements for Alluvium in Support of the Source Physics Experiments

Mechanical properties on alluvium blocks and core samples were determined to support the Source Physics Experiment Dry Alluvium Geology experimental series. Because material was not available directly from the experimental location, the alluvium blocks and core samples are intended to serve as surrogate material . P - and S - wave velocity was measured on cubes cut from the alluvium blocks and core with the intention to study variation from water content and measured direction (material anisotropy). Indirect tensile tests were conducted dry and with moisture ranging from 6 to 9.1%. For the range of water content tested, increasing moisture level resulted in slower P - and S - wave velocities. P - and S - wave variability is less influenced by material heterogeneity than moisture content. P - wave velocity ranges from 629 m/s to 2599 m/s and S - wave velocity ranges from 288 m/s to 1200 m/s. Counter to the velocity measurement findings, material variability on indirect tensile strength has a greater effect than moisture content. Compared to dry strength and at moisture levels from 6 to 9% the block's tensile strength was lowered by at least a factor of 5. Indirect tensile strength for the first block averaged 0.35 MPa and 0.25 MPa for dry and 8.9% moisture respectively. For the second block indirect tensile strength averaged 0.05 MPa for both dry and 6.4% moisture.

36 MATERIALS SCIENCE↗