Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Solar cell”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Characterization of dangling bond defects at the crystalline Si/SiO x interface in a polycrystalline Si passivating contact solar cell at room temperature with electrically detected magnetic resonance spectroscopy

Monocrystalline silicon solar cells can achieve photoconversion efficiencies exceeding 26%; however, performance-limiting defects that trap carriers continue to be a challenge. In this work, we have characterized Si solar cells with tunneling SiO x /polycrystalline-Si (poly-Si) passivating contacts (TOPCon) on As-doped Czochralski Si wafers with electrically detected magnetic resonance (EDMR) spectroscopy. We fabricated 2 × 20 mm 2 TOPCon-like mini solar cells with edge passivation alongside larger 4 cm 2 sister cells and obtained similar device characteristics. We performed EDMR spectroscopy at 300 K on two minicells with different degrees of surface passivation based on the recombination parameter, J o , values of 40 and 310 fA/cm2. We optimized the resolution and the signal-to-noise ratio of the EDMR response of the minicells by varying the forward bias voltage and the magnetic field modulation amplitude. We detect two distinct signals with EDMR spectroscopy, an axial-like signal at g = 2.009, 2.0087, and 2.0015, and an isotropic signal at g = 2.0024, which we attribute to Si dangling bonds (P b0 and P b centers) and boron–oxygen related defects, respectively, at or near the c-Si/SiO x interface. The EDMR signals were lower for the cell with a lower value of J o , while the ratio of the two defect populations was very similar. The EDMR signal increases with forward bias but drops to zero at bias voltages >0.5 V, consistent with interface defects within or near the boron-doped emitter depletion region. Our study demonstrates a method to fabricate minicells that can be characterized with EDMR spectroscopy to detect industrially relevant defects in TOPCon cells.

14 SOLAR ENERGY↗
DOE OSTI2022

Formation of a Secondary Phase in Thermally Evaporated MAPbI 3 and Its Effects on Solar Cell Performance

Thermal evaporation is a promising deposition technique to scale up perovskite solar cells (PSCs) to large areas, but the lack of understanding of the mechanisms that lead to high-quality evaporated methylammonium lead triiodide (MAPbI 3 ) films gives rise to devices with efficiencies lower than those obtained by spin coating. Here this work investigates the crystalline properties of MAPbI 3 deposited by the thermal coevaporation of PbI 2 and MAI, where the MAI evaporation rate is controlled by setting different temperatures for the MAI source and the PbI 2 deposition rate is controlled with a quartz crystal microbalance (QCM). Using grazing incident wide-angle X-ray scattering (GIWAXS) and X-ray diffraction (XRD), we identify the formation of a secondary orthorhombic phase (with a Pnma space group) that appears at MAI source temperatures below 155 °C. With synchrotron-based X-ray fluorescence (XRF) microscopy, we show that the changes in crystalline phases are not necessarily due to changes in stoichiometry. The films show a stochiometric composition when the MAI source is heated between 140 to 155 °C, and the samples become slightly MAI rich at 165 °C. Increasing the MAI temperature beyond 165 °C introduces an excess of MAI in the film, which promotes the formation of films with low crystallinity that contain low-dimensional perovskites. When they are incorporated in solar cells, the films deposited at 165 °C result in the champion power conversion efficiency, although the presence of a small amount of low-dimensional perovskite may lead to a lower open-circuit voltage. We hypothesize that the formation of secondary phases in evaporated films limits the performance of PSCs and that their formation can be suppressed by controlling the MAI source temperature, bringing the film toward a phase-pure tetragonal structure. Control of the phases during perovskite evaporation is therefore crucial to obtain high-performance solar cells.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Effects of Residual DMSO Adduct on Photonically Cured MAPbI 3 Solar Cells

Defects and impurities in halide perovskite solar cells can negatively impact device performance and long-term stability. In this study, we identify photonically cured methylammonium (MA) lead iodide films contain a residual adduct, MA 2 Pb 3 I 8 (dimethyl sulfoxide) 2 (MA 2 Pb 3 I 8 (DMSO) 2 ), that reduces photocurrent generation in perovskite solar cells (PSCs). This is evidenced by a decrease in the external quantum efficiency (EQE) near 400 nm. Similar EQE reductions were observed in PSCs produced using high-speed processes but have not been thoroughly examined. Through X-ray diffraction patterns and Fourier transform infrared spectroscopy, we establish the photo-inactive MA 2 Pb 3 I 8 (DMSO) 2 as the culprit for the EQE reduction. Combined experimental and simulation results reveal that the MA 2 Pb 3 I 8 (DMSO) 2 phase is located at the hole transport layer/ interface, not on the surface, resulting in lower quantum efficiency and surface photovoltage in the short wavelength region. The residual adduct is kinetically trapped due to the short processing time (20 ms) and crystallization direction but can be removed by an additional photonic pulse. Furthermore, this study highlights the need for careful examination of resulting materials beyond device efficiency when transitioning from laboratory processing to industrial high-speed methods.

14 SOLAR ENERGY↗
DOE OSTI2023

First of Their Kind: Solar Cells with a Dry-Processed Perovskite Absorber Layer via Powder Aerosol Deposition and Hot-Pressing

Preparing halide perovskite films by solvent-free, powder-based processing approaches currently attracts more and more attention. However, working solar cells employing dry, powder-based halide perovskite thin films, have not been demonstrated so far. Herein, perovskite solar cells are presented where the absorber layer is prepared by transferring readily synthesized perovskite powders into a compact thin film using a fully dry-powder-processing concept. Compact thin films are deposited via an optimized powder aerosol deposition (PAD) process. Pressing at 120 °C further improves the morphology and the optoelectronic film properties. Integrating the perovskite films in a solar cell configuration results in fully working devices, with champion power conversion efficiencies of >6%. While the (optoelectronic) properties of the PAD-processed films are found to be comparable with their solution-processed counterparts, investigations of the solar cell stack suggest deterioration of the electron-transport layer properties due to the PAD process, and the presence of hydrates at the perovskite surface to be important factors that contribute to the limited solar cell efficiency. Herein, perspectives to overcome the identified limitations are outlined, emphasizing the high potential and realizability of efficient perovskite solar cells based on dry-powder-processing approaches in the future.

14 SOLAR ENERGY↗
DOE OSTI2021

Long-Term Degradation of Passivated Emitter and Rear Contact Silicon Solar Cell under Light and Heat

Advanced designs enable high-efficiency solar cells; however, more complex structures create new long-term stability concerns. Herein, the long-term degradation processes affecting advanced silicon solar cells using laboratory-based illumination and heating over hundreds of hours are investigated. The activation energy for the degradation of voltage is estimated and the degradation rates to normal solar cell operating temperature ranges are extrapolated. The cell degradation observed at high temperatures in the lab is kinetically similar to the process affecting field-deployed modules contributing to 0.37% year-1 of annualized degradation. Electroluminescence and photoluminescence mapping show that the degradation is dominated by minority carrier lifetime reduction. Suns-open-circuit voltage and light beam-induced current results indicate that the degradation could result from passivation degradation at the surface or defect formation in the near-subsurface region, leading to increased minority carrier recombination. This work highlights a long-term degradation process under elevated temperature and illumination that may continue to affect cells in an irreversible manner that is separate from recoverable light-induced degradation and light- and elevated temperature-induced degradation.

14 SOLAR ENERGY↗
DOE OSTI2020

Damp Heat Induced Degradation of Silicon Heterojunction Solar Cells With Cu-Plated Contacts

Damp heat exposure is one of the most stringent environments for testing the durability of solar cells in packaged modules. Damp heat stresses and induces a variety of degradation modes in solar cells and modules: for example, moisture-induced corrosion of electrodes and interconnections, deterioration of polymeric materials, and/or thermally activated diffusion processes. To screen for these and other potential degradation modes, we subject one-cell modules containing silicon heterojunction (SHJ) solar cells with Cu-plated contacts to extended damp heat tests at 85 °C/85% relative humidity. SHJ cells were laminated with two common encapsulants: ethylene vinyl acetate (EVA) and polyolefin elastomer (POE), and two constructions: glass-backsheet and glass-glass. We observe degradation in all components of solar cell maximum power (PMP): current, voltage, and fill factor, and find evidence of increased carrier recombination and nonideal diode behavior with increasing stress. For glass-backsheet constructions, EVA samples generally degrade more than POE by a factor of approximately 1.5x PMP, and the different encapsulants produce different degradation patterns. Similar trends are observed in glass-glass modules, but to a lesser degree. In a different experiment, we observe a decrease in effective minority carrier lifetime of nonmetallized SHJ precursors measured after damp heat. This implies that some degradation unrelated to the contacts is to be expected and confirms the observation of increasing recombination.

14 SOLAR ENERGY↗
DOE OSTI2021

SnS Homojunction Solar Cell with n-Type Single Crystal and p-Type Thin Film

Herein, a pn homojunction SnS solar cell is fabricated for the first time by the deposition of p-type SnS polycrystalline thin films on the recently reported large n-type SnS single crystals. The p-type thin films consist of columnar grains that grow along the <100> direction, which is the same orientation as the n-type single crystal. In addition, the interface of the pn homojunctions is void-free and compositionally sharp. The SnS homojunction solar cell achieves an open-circuit voltage (VOC) of 360 mV, which is as large as the highest VOC of previously reported SnS-based heterojunction solar cells. The built-in potential of the homojunction cell is 0.92 eV, which is close to the bandgap energy of SnS (≈1.1 eV), and larger than reported for heterojunctions (≈0.7 eV). The resulting 1.4% conversion efficiency (n) of the homojunction solar cell is smaller than the record 4–5% in heterojunctions, mainly due to the low short-circuit current density (J SC ) of 7.5 mA cm -2 . Once the device structure of the homojunction cell is optimized to efficiently collect the photogenerated carriers and achieve a comparable J SC as the conventional heterojunction cells (≈25 mA cm -2 ), high n exceeding 4–5% will be realized with improving the VOC.

14 SOLAR ENERGY↗
DOE OSTI2022

Near–Band–Edge Enhancement in Perovskite Solar Cells via Tunable Surface Plasmons

Plasmonic perovskite solar cells (PSCs) using core-shell type plasmonic particles are designed, which possess the plasmon resonance in the near-infrared range. This can selectively strengthen the interaction of the perovskite layer with low-energy photons. The mesoporous PSCs employing the plasmonic particles have delivered a 10%-15% enhancement of external quantum efficiency in the plasmonic resonance range. This surface-plasmonic effect has been analyzed using complementary techniques, including selective wavelength excitation and time-dependent photoluminescence. Here it is shown that the metal-based core-shell-type plasmonic structures in PSCs optimize the scattering and absorption of incident light and the dynamics of photogenerated carriers. Furthermore, both optical and electronic effects increase the power conversion efficiency of PSCs from 17.49% to 19.88%, paving a way toward controlling the thickness of the photoactive layer for advanced devices such as tandem solar cells.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Solar cells formed via aluminum electroplating

Electroplating of aluminum may be utilized to form electrodes for solar cells. In contrast to expensive silver electrodes, aluminum allows for reduced cell cost and addresses the problem of material scarcity. In contrast to copper electrodes which typically require barrier layers, aluminum allows for simplified cell structures and fabrication steps. In the solar cells, point contacts may be utilized in the backside electrodes for increased efficiency. Solar cells formed in accordance with the present disclosure enable large-scale and cost-effective deployment of solar photovoltaic systems.

Tao, Meng↗
DOE OSTI2020

Six-junction III–V solar cells with 47.1% conversion efficiency under 143 Suns concentration

Single-junction flat-plate terrestrial solar cells are fundamentally limited to about 30% solar-to-electricity conversion efficiency, but multiple junctions and concentrated light make much higher efficiencies practically achievable. Until now, four-junction III–V concentrator solar cells have demonstrated the highest solar conversion efficiencies. Here, we demonstrate 47.1% solar conversion efficiency using a monolithic, series-connected, six-junction inverted metamorphic structure operated under the direct spectrum at 143 Suns concentration. Furthermore, when tuned to the global spectrum, a variation of this structure achieves a 1-Sun global efficiency of 39.2%. Nearly optimal bandgaps for six junctions were fabricated using alloys of III–V semiconductors. To develop these junctions, it was necessary to minimize threading dislocations in lattice-mismatched III–V alloys, prevent phase segregation in metastable quaternary III–V alloys and understand dopant diffusion in complex structures. Further reduction of the series resistance within this structure could realistically enable efficiencies over 50%.

14 SOLAR ENERGY↗
DOE OSTI2022

Interface Reconstruction from Ruddlesden–Popper Structures Impacts Stability in Lead Halide Perovskite Solar Cells

The impact of the bulky-cation-modified interfaces on halide perovskite solar cell stability is underexplored. Here, in this work, the thermal instability of the bulky-cation interface layers used in the state-of-the-art solar cells is demonstrated. X-ray photoelectron spectroscopy and synchrotron-based grazing-incidence X-ray scattering measurements reveal significant changes in the chemical composition and structure at the surface of these films that occur under thermal stress. The changes impact charge-carrier dynamics and device operation, as shown in transient photoluminescence, excitation correlation spectroscopy, and solar cells. The type of cation used for surface treatment affects the extent of these changes, where long carbon chains provide more stable interfaces. These results highlight that prolonged annealing of the treated interfaces is critical to enable reliable reporting of performances and to drive the selection of different bulky cations.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Stability of Tin-Lead Halide Perovskite Solar Cells

Tin-lead perovskites have low band gaps (1.2 eV - 1.4 eV) that offer complementary absorption spectra to mixed halide perovskites with band gaps in the range of 1.6 eV - 1.85 eV. In combination, tin-lead and mixed halide perovskites can be used to make efficient all-perovskite tandem solar cells. While these can achieve high efficiency, they are hampered by the unproven longterm stability of tin-containing perovskites. We make the first demonstration of tin-lead perovskite solar cells that pass benchmark 1000-hour tests of stability under stressors of heat, light, and atmospheric exposure. We identify that mixed tin-lead perovskites oxidise by a different chemical pathway, one that is much less favourable, than the oxidation pathway followed by pure tin perovskites, making them significantly more stable. Fortuitously, mixed tin-lead perovskites also have band gaps that are close to ideal for the rear cell of an all-perovskite monolithic two-junction tandem. Beyond selecting the composition of the perovskite to be one that has inherently suppressed tendency to oxidise, we also fabricate a novel heterojunction-based architecture that eliminates the commonly used acidic PEDOT:PSS layer, which leads to enhanced stability. By packaging the resulting solar cell in a glass-on-glass package with a pliable low-elastic-modulus polyolefin encapsulant and a butyl rubber edge seal, we also demonstrate that the low band gap perovskite solar cell that passes the IEC damp heat test for thin film solar cells - a milestone that demonstrates the removal of a significant impediment to the commercialization of high efficiency perovskite tandem solar cells.

14 SOLAR ENERGY↗
DOE OSTI2021

Exceeding 200 ns Lifetimes in Polycrystalline CdTe Solar Cells

CdTe photovoltaics has achieved one of the lowest levelized costs of electricity among all energy sources. However, for decades, carrier lifetimes have been inferior to those of other prevalent solar cell materials. This quality has inhibited common methods to improve solar cell efficiency such as back-surface fields, electron reflectors, or bifacial solar cells. In this work, a significant increase in carrier lifetime to values exceeding 200 ns in fully functional CdTe solar cells is demonstrated. The increased lifetime is achieved by large CdSeTe grains at the absorber/emitter interface, intragrain passivation in the absorber layer, and chemical passivation by forming nanoscale oxidized tellurium species at the transparent conducting oxide interface. The carrier lifetime is correlated to the open-circuit voltage and enables paths for back-surface manipulation and novel cell architectures to further improve CdTe photovoltaic performance.

14 SOLAR ENERGY↗
DOE OSTI2022

Technoeconomic Analysis of Dye Sensitized Solar Cells (DSSCs) with WS 2 /Carbon Composite as Counter Electrode Material

Exploration of clean and renewable energy materials is necessary due to the coming energy crisis and environmental problems. Solar energy is one of the favorable energy sources because of the continuous energy reservoir and its affluence. Silicon-based solar devices are expensive due to their complicated production process, which limits this technology for urban and other commercial applications. Among the third generation of solar cells, Dye-Sensitized Solar Cells (DSSCs) have attracted widespread attention as potential cost-effective alternatives to silicon-based solar cells. In this paper, the commercializing potential of the DSSCs is investigated. A module is introduced where the materials, equipment, and distribution of direct manufacturing costs are calculated. The manufacturing costs and the Levelized Cost of Energy (LCOE) of these DSSCs for a system lifetime of 25 years were determined to be USD 22.40 per m 2 and USD 0.0438 per kWh and the module price of this technology is USD 0.18 per W and the total installed system cost is USD 0.88 per W in Kansas which suggest that this PV technology could challenge other leading PV technologies.

14 SOLAR ENERGY↗
DOE OSTI2021

New Approaches to Low-Cost Scalable Doping of Interdigitated back Contact Silicon Solar Cells (Final Report)

The goal of this project was to develop novel approaches to patterning of dopants in the rear fingers of interdigitated back contact (IBC) Si solar cells to reduce the cost of manufacturing this high-efficiency-potential cell architecture. The work throughout this project can be divided into four categories: (a) development of dopant patterning technique using laser scribed Si contacts masks that are mechanically aligned with ~10 μm resolution to the underlying Si substrate; (b) measuring dopant spreading profiles in the isolation region between n- and p-type dopant fingers during plasma-enhanced chemical vapor deposition (PECVD) of doped hydrogenated amorphous silicon (a-Si:H) via shadow masks, and dopant desorption and re-adsorption during high-temperature annealing; (c) understanding the role of dopant compensation on the shunt resistance in contaminated isolation regions through analysis of defect-enhanced compensation; and (d) simulation and fabrication of passivated two-sided grid and back-contact solar cells to demonstrate the use of direct dopant patterning in cell fabrication. For the passivated two-sided grid solar cells, masked deposition was used to demonstrate an improvement in the blue response of the cell by creating a shallow front emitter. During development of the masked PECVD patterning process, we measured 3-D dopant profiles using secondary ion mass spectrometry. After deposition, in the masked region, the phosphorus dopant tail was >100 µm at concentrations >10 19 cm -3 while the boron dopant tail was shorter. During high-temperature crystallization of doped a-Si:H films to polycrystalline Si (poly-Si), phosphorus atoms spread by desorbing from the poly-Si surface and re-adsorbing onto intrinsic poly-Si on adjacent wafers that were separated by several millimeters. These contamination mechanisms resulted in a decrease in resistivity from ~10 5 Ω·cm for intrinsic poly-Si to ~10 -1 Ω·cm for contaminated poly-Si. Mitigation strategies for each contamination mechanism were developed to maintain a resistivity of ~10 5 Ω·cm between doped fingers. During fabrication of the 209 cells created during this project, it was found that despite contamination of the IBC gap through the abovementioned mechanisms, high shunt resistances and FF ~75% were still reached. Investigation into this led to the discovery of defect-enhanced compensation which exists within highly defective poly-Si when net doping concentrations reach the value of defect density (~10 18 cm -3 for many poly-Si films). Simulations guided us in the fabrication of IBCs and the cells fabricated were able to meet the year-end goals for BP 2 and 3 of 15% and 17% IBC cell efficiency, as well as the BP 4 goal of a 1% absolute increase in efficiency for PERC-like devices. However, the most efficient cell created during this project of 18.6% fell short of the 21% final project target. While the champion device fell short in V oc and J sc , many devices fabricated were able to reach the necessary goals of ~40 mA/cm 2 , ~700 mV, and ~75% FF required for a 21% device. The results generated from this project were disseminated through 11 conference presentations and proceedings. Presentations included oral talks at 2019 IEEE PVSC, 2019 MRS Fall Meeting, 2020 PVSEC-30 and 2021 IEEE PVSC, as well as poster presentations at 2020 IEEE PVSC and 2021 SiPV. The project resulted in 2 peer reviewed publications – one published in IEEE Journal of Photovoltaics and one in ACS Applied Energy Materials. The information gained in this project will aid in development of improved processes for fabrication of high-efficiency solar cells and other areas of the semiconductor device industry as well. The IBC cells will also pave the way for higher efficiency tandem devices. Through further manufacturing of high-efficiency solar cells, more of the world’s energy demands can be met through renewable sources, helping to stave off the worst effects that may come about from global climate change.

14 SOLAR ENERGY↗
DOE OSTI2021

On-Device Lead Detention for Perovskite Solar Cells

As the power conversion efficiency (PCE) of perovskite solar cells (PSCs) have reached above 25.5%, the commercialization of PSCs appears to be imminent due to its lower fabrication cost, simpler manufacturing processes, and larger processing area over Si-based solar cells that dominate the current photovoltaic (PV) market. While many efforts have focused on tackling the stability and scalability issues with promising advances, the potential lead (Pb) toxicity issue has remained a concern of PSCs. Unlike the metallic Pb, the Pb 2+ in perovskite generally exhibit high solubility in water. However, Pb 2+ has so far appeared to be a necessary component in all high-efficiency PSCs. Handful methods have been explored to mitigate the potential Pb2+ leaking issue, which can be generally categorized as physical encapsulation and our pioneering chemical absorption method, which was extended by others later. Since device damage is inevitable in outdoor conditions, physical encapsulation alone is not sufficient to mitigate the long-term risk of leakage of soluble Pb 2+ to the environment under severe weather conditions. As a result, the chemical absorption approach has recently attracted significant attention as a more effective solution to confine the potential lead leakage. Hence, it is of great value to develop durable and highly efficient Pb-absorbing components that can be conveniently mounted onto the standard PSC stack as an add-on accessory in line with the encapsulation of PSCs instead of modifying the standard device fabrication and/or device configuration.

14 SOLAR ENERGY↗
DOE OSTI2024

Effect of ZnO and PEDOT:PSS charge selective layers on photovoltage of cuprous oxide (Cu 2 O) heterojunction solar cells

Electrochemical deposition (ECD) of Cu 2 O provides a scalable and low temperature pathway to solar cells with a theoretical high energy conversion efficiency of 23%, based on the 2.0–2.2 eV band gap of Cu 2 O. However, existing ECD-Cu 2 O devices are plagued by poor crystallinity and low selectivity of the electron and hole transport layers. Here we use Vibrating Kelvin Probe Surface Photovoltage Spectroscopy (VKP-SPV) to probe the charge transfer selectivity in FTO/ZnO/Cu 2 O/PEDOT:PSS/Ni heterojunction solar cells. Selective electron extraction is achieved at the ZnO back contact to Cu 2 O, as confirmed by a negative surface photovoltage signal. While the uncoated Cu 2 O surface is electron-selective due to the formation of a hole depletion layer, spin coating of a PEDOT:PSS film turns it into a hole-selective interface. After adding nickel metal ink top electrodes, functional 1.0 cm 2 solar cells with power conversion efficiency (PCE) of up to 0.07%, 195 mV open-circuit voltage, and 1.28 mA cm –2 short-circuit photocurrent are achieved. The photovoltaic performance is higher for aluminum doped zinc oxide (AZO) substrates than for fluorine doped tin oxide (FTO) due to the presence of a n-/p-junction that further increases the electron selectivity of the AZO/ZnO/Cu 2 O contacts. Overall, this work demonstrates the first application of PEDOT:PSS as a hole transport layer (HTL) for Cu 2 O and the use of VKP-SPV to measure the photovoltage contributions of the Cu 2 O interfaces. Furthermore, the ability to fabricate Cu 2 O solar cells at near room temperature without the use of vacuum methods or rare elements is an important step towards a scalable Cu 2 O PV technology.

14 SOLAR ENERGY↗
DOE OSTI2022

Triple-junction solar cells with 39.5% terrestrial and 34.2% space efficiency enabled by thick quantum well superlattices

Multijunction solar cell design is guided by both the theoretical optimal bandgap combination as well as the realistic limitations to materials with these bandgaps. For instance, triple-junction III-V multijunction solar cells commonly use GaAs as a middle cell because of its near-perfect material quality, despite its bandgap being higher than optimal for the global spectrum. Here, we modify the middle cell bandgap using thick GaInAs/GaAsP strain-balanced quantum well (QW) solar cells with excellent voltage and absorption. Additionally, these high-performance QWs are incorporated into a triple-junction inverted metamorphic multijunction device consisting of a GaInP top cell, GaInAs/GaAsP QW middle cell, and lattice-mismatched GaInAs bottom cell, each of which has been highly optimized. We demonstrate triple-junction efficiencies of 39.5% and 34.2% under the AM1.5 global and AM0 space spectra, respectively, and the global efficiency is higher than previous record six-junction devices.

14 SOLAR ENERGY↗