Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Scale up”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS2019

A Pulsar-Based Time-Scale from the International Pulsar Timing Array

We have constructed a new time-scale, TT(IPTA16), based on observations of radio pulsars presented in the first data release from the International Pulsar Timing Array (IPTA). We used two analysis techniques with independent estimates of the noise models for the pulsar observations and different algorithms for obtaining the pulsar time-scale. The two analyses agree within the estimated uncertainties and both agree with TT(BIPM17), a post-corrected time-scale produced by the Bureau International des Poids et Mesures (BIPM). We show that both methods could detect significant errors in TT(BIPM17) if they were present. We estimate the stability of the atomic clocks from which TT(BIPM17) is derived using observations of four rubidium fountain clocks at the US Naval Observatory. Comparing the power spectrum of TT(IPTA16) with that of these fountain clocks suggests that pulsar-based time-scales are unlikely to contribute to the stability of the best time-scales over the next decade, but they will remain a valuable independent check on atomic time-scales. We also find that the stability of the pulsar-based time-scale is likely to be limited by our knowledge of solar-system dynamics, and that errors in TT(BIPM17) will not be a limiting factor for the primary goal of the IPTA, which is to search for the signatures of nano-Hertz gravitational waves.

G. Hobbs↗
NASA NTRSDate not supplied

Challenges in Scaling Analysis from Coupons to Elements in 3D Woven Composites for a Launch Vehicle End-Ring Structure

The limitations of structural design with 3D woven composites based on homogenized material models characterized using coupon test data, representative unit cell analysis, or a combination of the two are discussed in the context of a space launch system (SLS)-scale end ring. Selected building block test configurations at the coupon, element, and subcomponent scales are described in detail. Highly instrumented tests and X-ray computed tomography inspections are used to characterize the structural behavior and associated damage progression with increasing load. It is shown that a single homogenized material constitutive relationship, applied at coupon and element scale, is not sufficient to model the structural response observed in both tests. In fact, substantially different stress-strain laws are required to predict the response of the coupon and element scale specimens, despite similar loading conditions. A model with discrete representation of the binder tows and cohesive interfaces to model matrix cracking shows much better agreement with the test data at the two length scales. Thus, evidence is provided showing that predictive structural analysis of 3D woven composites requires discrete representation of the tows, matrix cracking morphology, and their interactions in the structural configuration. With accurate knowledge of the element scale behavior, engineering approximations readily enable analysis scale-up to the subcomponent level.

Andrew C Bergan↗
NASA NTRSDate not supplied

Toward A Method for Scaling Human Body Models in an IMU-Based Workflow

- Scaled biomechanical models can more accurately inform crew health decisions when tailored to the wide range of astronaut sizes. One component to improve scaling of existing models to better represent each unique astronaut’s size is the individual length scaling of limbs. Traditionally, limb lengths are determined by motion capture or manual measurement. - A new method is herein proposed for length scaling which can be done by measuring linear and angular accelerations at a desired point during isolated motion around a point of rotation, then calculating the distance between the desired point and point of rotation. - When an Inertial Measurement Unit (IMU) device is placed at the distal point of a limb, the isolated motion is about that limb’s proximal joint. This method of scaling limb segments can be used for any limb that has an easily defined proximal joint for the limb to rotate around including hands, arms, legs, feet. - Calculated limb lengths are then used to scale models to each unique astronaut’s size, thereby improving the applicability of the model. - This method was investigated as a possible away to obtain scaling information in data collections where IMUs are worn, but optical motion capture may not always be available, such as inside spacesuits or during crew exercise on the International Space Station.

E. K. Marecki↗
NASA NTRSDate not supplied

Structural Requirements and Scaling Analysis of a Fluidic Mirror Space Telescope Support Structure

The NASA FLUTE project proposes large-scale (50m) fluidic telescopes for astronomy applications. To continue to explore the universe, astronomers require larger and larger telescope apertures. The highest priority astrophysics targets such as exoplanets and early galaxies are extremely faint, motivating larger telescope apertures. However, mission costs depend on aperture diameter, and scaling apertures beyond 10-m apertures faces economic and technological viability challenges. An unsegmented primary mirror made in space via fluidic microgravity shaping would provide a scalable and cost-effective method to scale apertures to 50-m scale while achieving sub-nanometer (root mean square) surface quality. Such microgravity fluidic shaping has been demonstrated in laboratory neutral buoyance environments, parabolic microgravity experiments, as well aboard the International Space Station. One of the main components of a fluidic observatory is the mirror frame. The frame must provide a stable bounding circular ring which the edges of the fluid mirror surface can wet. The frame can optionally provide a ‘floor’ surface on the interior of the ring to provide additional fluid support and reduce required fluid volume. In this work, we evaluate several classes of structural frame architectures potentially suitable for a fluidic telescope support structure. We start by estimating stability requirements, orbital, station keeping, and slew loads based on a notional CONOPS. The scaling of overall fluid mass required for each architecture is evaluated. Preliminary results elucidate the importance of a support floor for overall mission viability above 10-m diameter. We then investigate the scaling of a tetrahedral truss frame support structure. We show that segmented solid shell support surfaces can provide sufficient stability at modest mass fractions. We estimate that the total fluid and frame mass for a 50-m telescope could be on the order of 15,000 kg. Finally, implementation considerations are discussed, including deployment/assembly methodologies. The results of this study establish feasibility of a large-scale fluidic telescope and will guide further architecture development and detailed structural design.

Christine Gregg↗
NASA NTRS2026

A Summary of Test and Analysis Results from a Second Lift+Cruise Full-Scale Drop Test

The realization of advanced air mobility markets is enabling new forms of transportation to take shape in the United States and around the world. Though currently in development, as these markets mature, new types of vertical take-off and landing (VTOL) vehicles have been undergoing development for use. There are many factors which must be addressed prior to these types of vehicles becoming viable alternative forms of transportation in these markets. These factors include incorporation into the existing airspaces, the logistics of operating in urban environments, along with numerous factors associated with safety and reliability. To address some of the safety aspects associated with the development of these new types of vehicles, NASA has been conducting research into the performance of an example electric VTOL (eVTOL) aircraft as a part of the Revolutionary Vertical Lift Technology (RVLT) project. Over the course of this research, many aspects including the development of energy absorbing components, the evaluation of seating systems, the development of advanced finite element material model systems and the acquisition of full-scale vehicle impact data were investigated. The report will discuss aspects related to the acquisition of full-scale vehicle data which occurred in the form of a full-scale impact test conducted in the Summer of 2025. This test was on a NASA designed Lift+Cruise composite cabin test article and represented a partial capstone in the entirety of previous eVTOL research conducted for the project. In this test, a variety of experiments were included in order to investigate the effect of a full-scale environment on the experiment results. In parallel, the development of a computational impact model to simulate the full-scale test will be discussed in this report. A model of the Lift+Cruise test article was developed utilizing data collected from previous sub- and full-scale test data and then simulated in the current test environment. The model development, its use in pre-test predictions, and its use in post-test correlation will all be presented. This report will present the test data acquired from the Lift+Cruise test and document several of the results obtained. One intended result is to determine the effect of a complex full-scale crash impact on the identification of occupant injury risk within seat and vehicle designs. A second intended result is to determine whether high-fidelity models can be used with some confidence in the prediction of test events and can allow for additional test cases to be simulated without the need of having to conduct additional tests. The overall goal of the test is to provide the community with data that can be used for design, development or certification efforts, along with providing data on what an example eVTOL crash incident could entail.

energy storage systems↗
NASA NTRS2017

Evaluation of Alternative Altitude Scaling Methods for Thermal Ice Protection System in NASA Icing Research Tunnel

A test was conducted at NASA Icing Research Tunnel to evaluate altitude scaling methods for thermal ice protection system. Two scaling methods based on Weber number were compared against a method based on the Reynolds number. The results generally agreed with the previous set of tests conducted in NRCC Altitude Icing Wind Tunnel. The Weber number based scaling methods resulted in smaller runback ice mass than the Reynolds number based scaling method. The ice accretions from the Weber number based scaling method also formed farther upstream. However there were large differences in the accreted ice mass between the two Weber number based scaling methods. The difference became greater when the speed was increased. This indicated that there may be some Reynolds number effects that isnt fully accounted for and warrants further study.

thermal scaling↗
NASA NTRS2018

Further Evaluation of Swept Wing Icing Scaling with Maximum Combined Cross Section Ice Shape Profiles

This study reports results from recent icing scaling tests conducted in the NASA Glenn Icing Research Tunnel (IRT) using recommended scaling methods that were developed for swept wing icing applications. The aluminum test articles used in this study were NACA 0012 Adjustable Sweep Airfoil Models. The reference and scale airfoils have a 36 inch and 15 inch chord measured normal to the leading edge, and a 60 inch and 24 inch span respectively. Reference tests were run with airspeeds of 100, 140.3 and 150 knot and MVD of 41.4, 44.4, 93 and 150 micron. All tests were set at 0⁰ angle of attack (AOA) and 30⁰ sweep angle. Results will be presented for stagnation freezing fractions ranging from 0.3 to 1.0. For non-dimensional reference & scale ice shape comparison, a new post-scanning ice shape digitization procedure was applied to extract 2-D "hand-tracing like" ice shape profiles, i.e. the Maximum Combined Cross Section or MCCS, at selected span-wise locations from the high fidelity 3-D scanned ice shapes obtained in the IRT. Preliminary assessment of ice shape comparison with MCCS showed that good scaling was achieved for the test conditions by using the recommended scaling methods developed for swept wing icing.

MCCS↗
NASA NTRS2019

Correlation of Full-Scale Isolated Proprotor Performance and Loads

A full-scale isolated proprotor test is currently being conducted in the USAF National Full-Scale Aerodynamics Complex (NFAC) 40- by 80-Foot Wind Tunnel at NASA Ames. The test article is a 3-bladed research rotor derived from the right-hand rotor of the AW609; this rotor was manufactured by Bell Helicopter under contract to NASA. In this paper, this research rotor is referred to as "699". The test, nearly completed, is an integral part of the initial checkout test of the newly developed Tiltrotor Test Rig (TTR), whose purpose is to test advanced, full-scale proprotors in the NFAC. Figure 1 shows the TTR/699 installed in the 40- by 80-Foot test section. The TTR rotor axis is horizontal and the rig rotates in yaw on the wind tunnel turntable for conversion (transition) and helicopter mode testing. To date, a substantial amount of wind tunnel test data has already been acquired. The completed operational conditions include hover, airplane mode (cruise, wind tunnel airspeed V=61 to 267 knots), and the helicopter and conversion conditions (with a comprehensive sweep of the TTR yaw angle ranging, to date, from 90-deg yaw helicopter mode to 30-deg yaw conversion mode, at varying airspeeds). This 699 proprotor performance and loads correlation study uses these newly acquired wind tunnel test data. This paper represents the third analytical study, coming after two earlier analytical studies on the TTR/699; that is, a 2018 paper on pre-test predictions of 699 performance and loads, Ref. 1, and an upcoming January 2019 paper on aeroelastic stability analysis of the TTR/699 installed in the 40- by 80-Foot Wind Tunnel, Ref. 2. Reference 8 will present an overview of the entire TTR/699 test program. For completeness, Ref. 3 addresses the development and initial testing of the TTR. Background information on the TTR effort at NASA Ames can be found at the Aeromechanics website: https://rotorcraft.arc.nasa.gov/Research/Facilities/ttr.html. To the authors' knowledge, the full-scale results presented in this paper are the first of their kind. A literature survey brought up several existing correlation studies, but these were either based on small-scale test data (for example, the studies performed by the University of Maryland) or full-scale aircraft flight test data (for example, flight tests conducted by Bell Helicopter). Separately, the 2009 NASA study involving the JVX rotor is relevant (see Ref.4). The JVX is closely similar to the 699 in size and aerodynamics, and is accordingly a good reference for performance calculations. In Ref. 1 (as mentioned above), pre-test reality checks of the current analytical model were made by comparing JVX and 699 predictions in hover and forward flight (airplane mode).

Isolated Proprotor Performance↗
NASA NTRS2019

Scaling Evaluation of Ice-Crystal Icing on a Modern Turbofan Engine in PSL Using the COMDES-MELT Code

This paper presents preliminary ice-crystal icing (ICI) altitude scaling evaluation results of a Honeywell Uncertified Research Engine (HURE) that was tested in the NASA Glenn Research Center Propulsion Systems Laboratory (PSL) during January of 2018. This engine geometry features a hidden core design to keep the core less exposed. The engine was fitted with internal video cameras to observe various ice buildup processes at multiple selected locations within the engine core flow path covering the fan stator, the splitter-lip/shroud/strut, and the high pressure compressor (HPC) variable inlet guide vane (IGV) regions. The potential ice accretion risk was pre-determined to occur by using NASA’s in-house 1D Engine Icing Risk assessment code, COMDES-MELT. The code was successful in predicting the risk of ice accretion in adiabatic regions like the fan-stator of the HURE at specific engine operating points. However at several operating points during the test, liquid water was observed running along the shroud toward the variable IGV of the HPC regions with an air temperature well below freezing, thus no particle melting could have occurred due to heating from the air alone. It was reasoned that other sources of heat were present in that region. To account for these heat sources the inlet total temperature was adjusted to give a wet bulb temperature of 24 F below the standard minimum wet bulb temperature of 492 R to allow ice to accrete in the splitter-lip/shroud/strut region, which was determined from a reference case where hard ice was observed in that region. With that adjustment the COMDES-MELT code was successful in providing operating points where there was a risk of ice accretion during the test campaign. In addition to calculating possible conditions at different selected lower altitudes, simulations were run to determine potential inlet conditions that could lead to ice-crystal accretion along the prescribed stations where the cameras were available. From there, scaled test conditions were determined by best matching the following three icing related parameters of the reference condition: (1) the local air total wet bulb temperature, (2) the local ice crystal cloud melt ratio and (3) the engine fan face ice/water to air mass flux ratio of the ice crystal cloud. Instantaneous images taken from the time-lapsed movies of ice buildup were used along with the relevant thermodynamic data of air, water vapor and local icing condition to help evaluate how closely the proposed altitude scaling method could be used in ground based test facility to duplicate selected reference ICI features observed at specific location inside this engine at different scale altitudes. Discussions on observed limitation for engine icing scaling application from this test campaign and needed improvement are provided. A scaling test procedure to help identify potential ICI risk conditions and possible ice accretion locations of a new turbofan engine is evaluated in PSL.

Engine Testing in PSL↗
NASA NTRS1972

Radiation scales on which standard values of the solar constant and solar spectral irradiance are based

The question of radiation scales is critically examined. There are two radiation scales which are of fundamental validity and there are several calibration standards and radiation scales which have been set up for practical convenience. The interrelation between these scales is investigated. It is shown that within the limits of accuracy of irradiance measurements in general and solar irradiance measurements in particular, the proposed standard values of the solar constant and solar spectrum should be considered to be on radiation scales of fundamental validity; those based on absolute electrical units and on the thermodynamic Kelvin temperature scale.

Thekaekara, M. P.↗
NASA NTRS1972

Evaluation of a 40 to 1 scale model of a low pressure engine

An evaluation of a scale model of a low pressure rocket engine which is used for secondary injection studies was conducted. Specific objectives of the evaluation were to: (1) assess the test conditions required for full scale simulations; (2) recommend fluids to be used for both primary and secondary flows; and (3) recommend possible modifications to be made to the scale model and its test facility to achieve the highest possible degree of simulation. A discussion of the theoretical and empirical scaling laws which must be observed to apply scale model test data to full scale systems is included. A technique by which the side forces due to secondary injection can be analytically estimated is presented.

Cooper, C. E., Jr.↗
NASA NTRS1974

The aurora as a source of planetary-scale waves in the middle atmosphere

Photographs of global scale auroral forms taken by scanning radiometers onboard weather satellites in 1972 show that auroral bands exhibit well organized wave motion with typical zonal wave number of 5 or so. The scale size of these waves is in agreement with that of well organized neutral wind fields in the 150- to 200-km region during the geomagnetic storm of May 27, 1967. Further, the horizontal scale size revealed by these observations are in agreement with that of high altitude traveling ionospheric disturbances. It is conjectured that the geomagnetic storm is a source of planetary and synoptic scale neutral atmospheric waves in the middle atmosphere. Although there is, at present, no observation of substorm related waves of this scale size at mesospheric and stratospheric altitudes, the possible existence of a new source of waves of the proper scale size to trigger instabilities in middle atmospheric circulation systems may be significant in the study of lower atmospheric response to geomagnetic activity.

Chiu, Y. T.↗
NASA NTRS1977

Large-scale V/STOL testing

Several facets of large-scale testing of V/STOL aircraft configurations are discussed with particular emphasis on test experience in the Ames 40- by 80-Foot Wind Tunnel. Examples of powered-lift test programs are presented in order to illustrate tradeoffs confronting the planner of V/STOL test programs. Large-scale V/STOL wind-tunnel testing can sometimes compete with small-scale testing in the effort required (overall test time) and program costs because of the possibility of conducting a number of different tests with a single large-scale model where several small-scale models would be required. The benefits of both high- or full-scale Reynolds numbers, more detailed configuration simulation, and number and type of onboard measurements are studied.

Koenig, D. G.↗
NASA NTRS1977

Radar backscattering from a sea having an anisotropic large-scale surface, part 2

A two scale scattering model was derived that combines specular reflections from sea waves and Bragg scattering in a manner consistent with energy conservation. The effect of the tilting of the small scale roughness by the large scale roughness was included, which accounted for the reduction of reflected power. The special case of backscattering for which the transmitted polarization equaled the received polarization was considered. An anisotropic large scale surface was used to specify the probability density function of the large scale surface normal. In order to isolate the azimuthal variation of the normalized radar cross section produced by the anisotropic probability density function, an isotropical small scale spectrum was assumed.

Wentz, F. J.↗
NASA NTRS1980

Effects of axisymmetric contractions on turbulence of various scales

Digitally acquired and processed results from an experimental investigation of grid generated turbulence of various scales through and downstream of nine matched cubic contour contractions ranging in area ratio from 2 to 36, and in length to inlet diameter ratio from 0.25 to 1.50 are reported. An additional contraction with a fifth order contour was also utilized for studying the shape effect. Thirteen homogeneous and nearly isotropic test flow conditions with a range of turbulence intensities, length scales and Reynolds numbers were generated and used to examine the sensitivity of the contractions to upstream turbulence. The extent to which the turbulence is altered by the contraction depends on the incoming turbulence scales, the total strain experienced by the fluid, as well as the contraction ratio and the strain rate. Varying the turbulence integral scale influences the transverse turbulence components more than the streamwise component. In general, the larger the turbulence scale, the lesser the reduction in the turbulence intensity of the transverse components. Best agreement with rapid distortion theory was obtained for large scale turbulence, where viscous decay over the contraction length was negligible, or when a first order correction for viscous decay was applied to the results.

Tan-Atichat, J.↗
NASA NTRS1982

An investigation of scale model testing of VTOL aircraft in hover

Utilizing the unique opportunity created by full scale hover testing of the twin-jet Grumman Design 698 VTOL aircraft in the NASA-Ames Hover Facility, a series of experiments was conducted to evaluate the effectivness of scale model testing in predicting full scale behavior. Interference forces were found to be sensitive to aircraft lower surface geometry, but when the geometry was modeled accurately the small scale results matched full scale forces guite well. The interference forces were found to be insensitive to core nozzle temperature and fan nozzle pressure ratio. The results clearly demonstrate that small scale models can be reliably utilized for aircraft and technology development when the appropriate sensitivities are recognized.

Hill, W. G., Jr.↗
NASA NTRS1982

Estimates of crater size for large-body impact Gravity-scaling results

A scaling analysis based upon dimensional invariance is used in conjunction with centrifuge experiments to estimate cratering efficiency as a function of impact velocity for kilometer-sized impactors. Complementing earlier, conventional small-scale impact experiments, centrifuge experiments were performed to substantiate these scaling laws in a scaled-size regime of interest. This technique provided empirical scaling laws used to estimate crater size for large bodies impacting the earth. From these scaling laws a 10-km-diameter body impacting at 25 km/s would be expected to produce a 66-km-diameter crater and to inject approximately 12 times its mass into the atmosphere.

Schmidt, R. M.↗
NASA NTRS1984

Large-scale inhomogeneities and galaxy statistics

The density fluctuations associated with the formation of large-scale cosmic pancake-like and filamentary structures are evaluated using the Zel'dovich approximation for the evolution of nonlinear inhomogeneities in the expanding universe. It is shown that the large-scale nonlinear density fluctuations in the galaxy distribution due to pancakes modify the standard scale-invariant correlation function xi(r) at scales comparable to the coherence length of adiabatic fluctuations. The typical contribution of pancakes and filaments to the J3 integral, and more generally to the moments of galaxy counts in a volume of approximately (15-40 per h Mpc)exp 3, provides a statistical test for the existence of large scale inhomogeneities. An application to several recent three dimensional data sets shows that despite large observational uncertainties over the relevant scales characteristic features may be present that can be attributed to pancakes in most, but not all, of the various galaxy samples.

Schaeffer, R.↗