Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SURFACE ROUGHNESS EFFECT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS1971

Shuttle ascent and shock impingement aerodynamic heating studies

The collection and analysis of aerodynamic heating data obtained from shock impingement experimental investigation were completed. The data were categorized into four interference areas; fin leading edge, wing/fuselage fin/plate corners, and space shuttle configurations. The effects of shock impingement were found to increase the heating rates 10 to 40 times the undisturbed values. A test program was completed at NASA/Langley Research Center to investigate the magnitudes and surface patterns of the mated shock interference flowfield. A 0.0065 scale thin-skin model of the MDAC 256-20 space shuttle booster mated with a Stycast model of the MDAC Internal tank orbiter was tested in the 20-inch M=6 tunnel, the 31-inch M=10 tunnel, and the 48-inch Unitary Plan Tunnel. The gap region of the ascent configuration was the principal area of interest where both thermocouple and phase-change paint data were obtained. Pressure and heat transfer distributions data on the leeward surface of a 75-degree sweep slab delta wing are presented. The effects of surface roughness on boundary layer transition and aerodynamic heating were investigated.

Lanning, W. D.↗
NASA NTRS1973

Effect of surface asperity on elastohydrodynamic lubrication

The important aspects of elastohydrodynamic lubrication, with a single, one-dimensional asperity, have been found by solving numerically the coupled transient Reynolds equation and the elasticity equation. Even though the assumption of a single asperity is highly ideal, this study sheds some light on the effect of surface roughness on elastohydrodynamic lubrication. The results show that the film pressure tends to increase more than the steady state pressure, and in particular, the increase in pressure reaches a maximum as the asperity approaches the inlet of the contact region. The asperity height and the pressure increase above the steady state pressure are closely related to each other; the higher the asperity height, the larger the pressure increase. In the pure rolling case, it has been found that a local pressure peak is not developed. However, in the cases of sliding and rolling, a small, local pressure peak is developed on the pressure profile when the asperity moves into the contact region. In general, the overall film thickness profile increases with increasing asperity height, but is not significantly affected by the asperity width. Moreover, the slope of the overall film thickness profile for the transient cases is much greater than the steady state profile, which is approximately constant across the contact width. The increase in the center film thickness also depends upon the width and height of the asperity.

Lee, K.↗
NASA NTRS1974

Asperity lubrication and cavitation in face seals

The basic aspect of parallel-surface lubrication that distinguishes it from other areas of lubrication technology is that classical lubrication theory does not predict the existence of a stable hydrodynamic film for steady-state, isothermal, incompressible flow between smooth, parallel surfaces. Hydrodynamic films between apparently parallel surfaces have been observed in practice and are often essential for the reliable performance of thrust bearings and seals. In order to account for this fortunate discrepancy between classical theory and experiment, load-support mechanisms relating to accidential features characteristic of seal performance, which relax one or more of the assumptions in the classical theory and permit the theoretical prediction of load support are proposed. Some of the features that have been analyzed are vibratory effects such as wobble and bounce, surface waviness, nonsymmetric rotation resulting from various types of misalignment, lubricant density change, non-Newtonian lubricant effects, and surface roughness.

Walowitt, J. A.↗
NASA NTRS1975

Developments in convective heat transfer models featuring seamless and selected detail surfaces, employing electroless plating

Several model/instrument concepts employing electroless metallic skin were considered for improvement of surface condition, accuracy, and cost of contoured-geometry convective heat transfer models. A plated semi-infinite slab approach was chosen for development and evaluation in a hypersonic wind tunnel. The plated slab model consists of an epoxy casting containing fine constantan wires accurately placed at specified surface locations. An electroless alloy was deposited on the plastic surface that provides a hard, uniformly thick, seamless skin. The chosen alloy forms a high-output thermocouple junction with each exposed constantan wire, providing means of determining heat transfer during tunnel testing of the model. A selective electroless plating procedure was used to deposit scaled heatshield tiles on the lower surface of a 0.0175-scale shuttle orbiter model. Twenty-five percent of the tiles were randomly selected and plated to a height of 0.001-inch. The purpose was to assess the heating effects of surface roughness simulating misalignment of tiles that may occur during manufacture of the spacecraft.

Stalmach, C. J., Jr.↗
NASA NTRS1977

Effects of surface cooling and of roughness on the heating (including transition) to the windward plane-of-symmetry of the shuttle orbiter

The theoretical heat-transfer distributions are compared with experimental heat-transfer distributions obtained in Tunnel B at AEDC using a 0.0175 scale model of the space shuttle orbiter configuration for which the first 80% of the windward surface was roughened by a simulated tile misalignment. The theoretical solutions indicate that thinning the boundary layer by surface cooling increased the nondimensionalized value of the local heat-transfer coefficient. Tile misalignment did not significantly affect the heat-transfer rate in regions where the boundary layer was either laminar or turbulent.

Bertin, J. J.↗
NASA NTRS1982

Radio frequency verification tasks related to a multiple aperture reflector system

The establishment of analytical methods for predicting the electromagnetic performance of multiple offset fed apertures for multiple beam large space antenna systems is highlighted. The development of experimental modeling techniques for verifying the analytical methods used in predicting the effects of surface roughness (pillows), scattering, and aperture coupling on RF performance is discussed.

Campbell, T. G.↗
NASA NTRS1983

A fundamental approach to the sticking of insect residues to aircraft wings

The sticking of insect residues to aircraft wings is investigated. The major topics of this review are: Experimentally tested methods, testing techniques, the effect of surface roughness height on aerodynamic drag, materials tested and, the adhesive properties of insect body fluids are reviewed.

Eiss, N. S., Jr.↗
NASA NTRS1983

Limb darkening of meteorites and asteroids

The limb darkening at small phase angles of several materials believed to be analogs of those found on the surfaces of asteroids and other related objects such as Phobos and Deimos is investigated. The materials include three carbonaceous chondrites, one ordinary chondrite, and a steel powder. The wavelength dependence of the limb darkening at visible and near-IR wavelengths is examined. The effects of surface roughness on limb-darkening parameters, and hence on measured geometric albedos, are estimated, and the implications for spherical and ellipsoidal asteroids are discussed.

French, L. M.↗
NASA NTRS1984

A fundamental approach to the sticking of insect residues to aircraft wings

A proposed testing scheme is described for obtaining data on the effects of surface roughness and surface energy on insect adhesion. The road test apparatus is discussed as well as surface preparation techniques. Uncoated and polymer coated metal substrates were analyzed by SEM/ESCA/IRS before and following collision with insects. Critical surface tensions of unexposed Nyebar and poly sulfone coatings were 10 and 33 dynes/cm, respectively, as determined from contact angles. A total of 95% of insect residues collected belong to order Diptera. Significantly less insect debris was detected on the coated plates as compared to the uncoated plates. Minimal contamination at the 5 nm level of both coated and uncoated plates occurs even after hours of exposure to road conditions as determined by ESCA analysis. The presence of nitrogen detected by ESCA on exposed plates is unequivocal evidence for insect residues left on plates.

Eiss, N. S., Jr.↗
NASA NTRS1983

Monte Carlo simulation of the effect of soil moisture variation on the microwave emission from soils

In this paper, results of a Monte Carlo simulation of the effect of noise on the relationship between the microwave emissivity of soil and its moisture content are presented. It is found that whenever the magnitude of the noise for the independent variable, in this case the soil moisture, is increased, both the slope of the regression and the correlation coefficient decrease. In particular, when the noise has magnitude equivalent to a coefficient of variation of 0.25, the slope and correlation coefficient are in good agreement with those obtained from the data of a 21-cm airborne microwave radiometer which was flown over a test site in hand county, South Dakota. The comparison was made using a linear relationship to determine the estimated emissivity from the ground measurements of soil moisture. The linear relationship was derived from a radiative transfer model calculation of the microwave emissivities using realistic soil-moisture profiles. The effect of surface roughness was included in the relationship, and the variability of the surface roughness was also simulated by a Monte Carlo technique.

Mo, T.↗
NASA NTRS1985

Microwave backscatter and emission observed from Shuttle Imaging Radar B and an airborne 1.4 GHz radiometer

A soil moisture experiment conducted with the Shuttle Imaging Radar B (SIR-B) is reported. SIR-B operated at 1.28 GHz provided the active microwave measurements, while a 4-beam pushbroom 1.4 GHz radiometer gave the complementary passive microwave measurements. The aircraft measurements were made at an altitude of 330 m, resulting in a ground resolution cell of about 100 m diameter. SIR-B ground resolution from 225 km was about 35 m. More than 150 agricultural fields in the San Joaquin Valley of California were examined in the experiment. The effect of surface roughness height on radar backscatter and radiometric measurements was studied.

Wang, J. R.↗
NASA NTRS1986

The wavelength dependence of phase coefficients

It is pointed out that spectral reflectance curves depend largely upon the optical constants of the surface materials. In the present study, the results of laboratory measurements are employed to investigate the wavelength dependence of disk-integrated phase coefficients of some materials, taking into account a basalt, the ordinary chondrite Bruderheim, the carbonaceous chondrite Allende, and sulfur. These materials have been selected as appropriate analogs to the surfaces of the moon, S- and C-class asteroids, and the Jovian satellite Io, respectively. It is shown that the observed wavelength dependence of phase coefficients can be predicted (at least qualitatively) once the spectrum of an object is known. Attention is given to phase variation of disk-integrated spectral reflectance curves, the wavelength dependence of phase coefficients, a comparison with observations, and the effects of surface roughness on phase coefficients.

Gradie, J.↗