Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SUPPORTS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

Use of MODIS Satellite Data to Evaluate Juniperus spp. Pollen Phenology to Support a Pollen Dispersal Model, PREAM, to Support Public Health Allergy Alerts

Pollen can be transported great distances. Van de Water et. al., 2003 reported Juniperus spp. pollen was transported 200-600 km. Hence local observations of plant phenology may not be consistent with the timing and source of pollen collected by pollen sampling instruments. The DREAM (Dust REgional Atmospheric Model, Nickovic et al. 2001) is a verified model for atmospheric dust transport modeling using MODIS data products to identify source regions and concentrations of dust. We are modifying the DREAM model to incorporate pollen transport. Pollen emission is based on MODIS-derived phenology of Juniperus spp. communities. Ground-based observational records of pollen release timing and quantities will be used as model verification. This information will be used to support the Centers for Disease Control and Prevention's National Environmental Public Health Tracking Program and the State of New Mexico environmental public health decision support for asthma and allergies alerts.

Luvall, J. C.↗

Use of MODIS Satellite Data to Evaluate Juniperus spp. Pollen Phenology to Support a Pollen Dispersal Model, PREAM, to Support Public Health Allergy Alerts

Pollen can be transported great distances. Van de Water et. al., 2003 reported Juniperus spp. pollen was transported 200-600 km. Hence local observations of plant phenology may not be consistent with the timing and source of pollen collected by pollen sampling instruments. The DREAM (Dust REgional Atmospheric Model) is a verified model for atmospheric dust transport modeling using MODIS data products to identify source regions and concentrations of dust. We are modifying the DREAM model to incorporate pollen transport. Pollen emission is based on MODIS-derived phenology of Juniperus spp. communities. Ground-based observational records of pollen release timing and quantities will be used as model verification. This information will be used to support the Centers for Disease Control and Prevention s National Environmental Public Health Tracking Program and the State of New Mexico environmental public health decision support for asthma and allergies alerts

Luvall, J. C.↗

Use of the SPoRT Stoplight Product to Support NWS Decision Support Services

The National Weather Service Forecast Offices (NWSFOs) use many weather tools and observational datasets to provide support for critical decision-making by core partners such as public safety officials, emergency managers, and first responders. These core partners who need weather decision support services (DSS) for outdoor events require up-to-the-minute weather information to ensure the safety and protection of attendees and workers. Storms and lightning, potentially deadly, pose a significant threat during outdoor events and are among the weather phenomena frequently cited as a DSS requirement. According to the National Lightning Safety Council, from 2014 up to August 2024, lightning resulted in 222 fatalities in the U.S. For outdoor events with hundreds to thousands of attendees, having the right tools to detect and monitor lightning activity is of utmost importance to protect lives. Common guidelines for lightning safety include moving inside a substantial structure at the first sight of threatening skies or the first sound of thunder, and waiting 30 minutes after the last lightning flash or thunder before returning outside. Using this guidance as a framework, scientists at the NASA Short-term Prediction Research and Transition (SPoRT) center have developed the Geostationary Lightning Mapper (GLM) Stoplight tool. This experimental tool uses the GLM Flash Extent Density imagery to display the location and recency of lightning flashes. To simplify interpretation, these lightning pixels are color-coded in 10-minute bins, ranging from red (lightning detected 0 to 10 minutes ago) to yellow (10 to 20 minutes ago) to green (20 to 30 minutes ago). The Stoplight tool also allows users to place markers at the location of outdoor events with range rings around the location to help in assessing the location and relative age of lightning flashes near and upstream of the event. The goal is to help NWS forecasters provide core partners with the necessary information to make the best decisions possible. While the Stoplight tool is experimental, forecasters at NWSFO Raleigh, NC, have periodically used the Stoplight guidance to evaluate its utility within NWS DSS. This presentation will discuss how the Stoplight tool was successfully used for DSS for four outdoor events in central NC in 2023 and 2024. Future improvements to this tool, including the addition of AI applications and the merging of ground-based lightning data with GLM data, will be reviewed.

Gail Hartfield↗

Data Diodes in Support of Trustworthy Cyber Infrastructure and Net-Centric Cyber Decision Support

Data diodes provide protection of critical cyber assets by the means of physically enforcing traffic direction on the network. In order to deploy data diodes effectively, it is imperative to understand the protection they provide, the protection they do not provide, their limitations, and their place in the larger security infrastructure. In this work, we study data diodes, their functionalities and limitations. We then propose two critical infrastructure systems that can benefit from the additional protection offered by data diodes: process control networks and net-centric cyber decision support systems. We review the security requirements of these systems, describe the architectures, and study the trade-offs. Finally, the architectures are evaluated against different attack patterns.

97 MATHEMATICS AND COMPUTING↗

Oxidation of porous stainless steel supports for metal-supported solid oxide fuel cells

Here, oxidation behavior of porous P434L ferritic stainless steel, used for the fabrication of metal-supported solid oxide fuel cells (MS-SOFC), is studied under anodic and cathodic atmospheres. Temperature- and atmosphere-dependence is determined for as-sintered and pre-oxidized stainless steel. Pre-oxidation reduced the long-term oxidation rate. For pre-oxidized samples, the oxidation rate in air exceeds that in humid hydrogen for temperatures above 700 °C. The influence of PrOx, LSCF-SDC, and Ni-SDC coatings is also examined. The coatings do not dramatically impact oxide scale growth. Oxidation in C-free and C-containing anodic atmospheres is similar. Addition of CO 2 , CH 4 , and CO to humidified hydrogen to simulate ethanol reformate does not significantly impact oxidation behavior. Cr transpiration in humid air is greatly reduced by the PrOx coating, and a PrCrO 3 reaction product is observed throughout the porous structure. A dense and protective chromia-based scale forms on steel samples during oxidation in all conditions. A thin silica enriched oxide layer also forms at the metal-scale interface. In general, the oxidation behavior at 700 °C is found to be acceptable.

25 ENERGY STORAGE↗

Oxidation of porous stainless steel supports for metal-supported solid oxide electrolysis cells

Oxidation behavior of porous P434L ferritic stainless steel, used for the fabrication of metal-supported solid oxide electrolysis cells (MS-SOEC), is studied under oxygen-side and steam-side conditions. The impact of oxygen content on the oxygen side and steam:hydrogen ratio on the steam side is determined at 700°C for bare, as-sintered samples. For these conditions, oxidation is more aggressive in the steam-side atmosphere. Oxygen with 3% humidification and steam:hydrogen ratio of 90:10 are selected for further assessment with pre-oxidized, catalyst-coated, and CuMn1·8O4-coated samples. The rapid oxidation at 700°C and breakaway oxidation at 600 °C observed for bare stainless steel in 90:10 steam:hydrogen is mitigated by pre-oxidizing the sample in air before exposure. In oxygen, addition of the catalyst or CuMn 1·8 O 4 coatings moderately increases the oxidation rate, due to consumption of Cr via reaction between the coatings and Cr-oxide scale. In conclusion, the results for ex-situ controlled oxidation are similar to oxidation observed after 1000h operation of a full MS-SOEC. In general, the oxidation behavior at 700°C is found to be acceptable.

08 HYDROGEN↗

Support Effect and Surface Reconstruction in In 2 O 3 / m- ZrO 2 Catalyzed CO 2 Hydrogenation

Here, we investigate the chemical and structural dynamics at the interface of In 2 O 3 /m-ZrO 2 and their consequences on the CO 2 hydrogenation reaction (CO 2 HR) under reaction conditions. While acting to enrich CO 2 , monoclinic zirconia (m-ZrO 2 ) was also found to serve as a chemical and structural modifier of In 2 O 3 that directly governs the outcome of the CO 2 HR. These modifying effects include the following: (1) Under reaction conditions (above 623 K), partially reduced In 2 O 3 , i.e., InO x (0 < x < 1.5), was found to migrate in and out of the subsurface of m-ZrO 2 in a semireversible manner, where m-ZrO 2 accommodates and stabilizes InO x by serving as a reservoir. The decreased concentration of surface InO x under elevated temperatures coincides with significantly decreased selectivity toward methanol and a sharp increase of the reverse water–gas shift reaction. The reconstruction-induced variation of InO x concentration appears to be one of the most important factors contributing to the altered catalytic performance of CO 2 HR at different reaction conditions. (2) The strong interactions and reactions between m-ZrO 2 and In 2 O 3 result in the activation of a pool of In–O bonds at the In 2 O 3 /m-ZrO 2 interface to form oxygen vacancies. On the other hand, the high dispersity of In 2 O 3 nanostructures onto m-ZrO 2 prevents their over-reduction under catalytically relevant conditions (up to 673 K), when bare In 2 O 3 is unavoidably reduced into the metallic phase (In 0 ). The relationship between the extent of reduction of In 2 O 3 and catalytic performance (CO 2 conversion, CH 3 OH selectivity, or yield of CH 3 OH) suggests the presence of an optimum coverage of surface InO x and oxygen vacancies under reaction conditions. The conventional model that links catalytic performance solely to the coverage of oxygen vacancies appears invalid in the present case. In situ analysis also allows the observation of surface reaction intermediates and their interconversions, including the reduction of CO 3 * into formate, a precursor for the formation of methanol and CO. The combinative ex situ and in situ study sheds light on the reaction mechanism of the CO 2 HR on In 2 O 3 /m-ZrO 2 -based catalysts. Our findings on the large-scale surface reconstructions, support effect, and the reaction mechanism of In 2 O 3 /m-ZrO 2 for CO 2 HR may apply to other related metal oxide catalyzed CO 2 reduction reactions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Support Induced Control of Surface Composition in Cu–Ni/TiO 2 Catalysts Enables High Yield Co-Conversion of HMF and Furfural to Methylated Furans

5-(hydroxymethyl)furfural (HMF) and furfural (FF) have been confirmed as valuable biomass-derived fuel precursors suitable for catalytic hydrodeoxygenation (HDO) to produce high octane fuel additives such dimethyl furan (DMF) and methyl furan (MF), respectively. In order to realize economically viable production of DMF and MF from biomass, catalytic processes with high yields, low catalyst costs, and process simplicity are needed. In this work, we demonstrate simultaneous co-processing of HMF and FF over Cu-Ni/TiO 2 catalysts, achieving 87.5% yield of DMF from HMF and 88.5% yield of MF from FF in a one pot reaction. The Cu-Ni/TiO 2 catalyst also exhibited improved stability and regeneration compared to Cu/TiO 2 and Cu/Al 2 O 3 catalysts for FF HDO, exhibiting a ~7% loss in FF conversion over 4 sequential recycles, compared to a ~50% loss in FF coversion for Cu/Al 2 O 3 and a ~30% loss in coversion for Cu/TiO 2 . Characterization of the Cu-Ni/TiO 2 catalyst by X-ray Photoelectron Spectroscopy, Scanning Transmission Electron Microscopy, and H 2 -Temperature Programmed Reduction and comparison to monometallic Cu and Ni on Al 2 O 3 and TiO 2 and bimetallic Cu-Ni/Al 2 O 3 catalysts suggest that the unique reactivity and stability of Cu-Ni/TiO 2 derives from support-induced metal segregation in which Cu is selectively enriched at the catalyst surface, while Ni is enriched at the TiO 2 interface. Our findings demonstrate that Cu-Ni/TiO 2 catalysts promise to be a catalyst system capable of integrating directly with a combined HMF and FF product stream from biomass processing to realize lower cost production of liquid fuels from biomass.

09 BIOMASS FUELS↗

Inverse Load Calculation of Wind Turbine Support Structures - A Numerical Verification Using the Comprehensive Simulation Code FAST: Preprint (Revised)

Physically measuring the dynamic responses of wind turbine support structures enables the calculation of the applied loads using an inverse procedure. In this process, inverse means deriving the inputs/forces from the outputs/responses. This paper presents results of a numerical verification of such an inverse load calculation. For this verification, the comprehensive simulation code FAST is used. FAST accounts for the coupled dynamics of wind inflow, aerodynamics, elasticity and turbine controls. Simulations are run using a 5-MW onshore wind turbine model with a tubular tower. Both the applied loads due to the instantaneous wind field and the resulting system responses are known from the simulations. Using the system responses as inputs to the inverse calculation, the applied loads arecalculated, which in this case are the rotor thrust forces. These forces are compared to the rotor thrust forces known from the FAST simulations. The results of these comparisons are presented to assess the accuracy of the inverse calculation. To study the influences of turbine controls, load cases in normal operation between cut-in and rated wind speed, near rated wind speed and between ratedand cut-out wind speed are chosen. The presented study shows that the inverse load calculation is capable of computing very good estimates of the rotor thrust. The accuracy of the inverse calculation does not depend on the control activity of the wind turbine.

17 WIND ENERGY↗

Open‐Pore Two‐Dimensional MFI Zeolite Nanosheets for the Fabrication of Hydrocarbon‐Isomer‐Selective Membranes on Porous Polymer Supports

Abstract Two‐dimensional zeolite nanosheets that do not contain any organic structure‐directing agents were prepared from a multilamellar MFI (ML‐MFI) zeolite. ML‐MFI was first exfoliated by melt compounding and then detemplated by treatment with a mixture of H 2 SO 4 and H 2 O 2 (piranha solution). The obtained OSDA‐free MFI nanosheets disperse well in water and can be used for coating applications. Deposits made on porous polybenzimidazole (PBI) supports by simple filtration of these suspensions exhibit an n ‐butane/isobutane selectivity of 5.4, with an n ‐butane permeance of 3.5×10 −7 mol m −2 s −1 Pa −1 (ca. 1000 GPU).

Zhang, Han↗