Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SHOCK WAVE INTERACTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

Numerical solution of a three-dimensional shock wave and turbulent boundary-layer interaction

A rapid numerical scheme is used to solve the complete mass-averaged Navier-Stokes equations for supersonic turbulent flow over a three-dimensional compression corner. A simple eddy viscosity model is developed, and the interaction of a swept shock wave and a three-dimensional turbulent boundary layer is studied. Good agreement is obtained between the present results and experimental measurements for the case of a wedge with an angle of 6 deg on a flat-plate sidewall. For the case of a 12-deg wedge angle, the computed results do not show the existence of a peak pressure found experimentally. However, the range of interaction, the plateau pressure, and the peak heat transfer are closely predicted for all cases. The high heat transfer near the axial corner is due to the thinning of the boundary layer and inflow of fresh high-momentum fluid. The heat transfer is relieved through pressure reduction and boundary-layer thickening.

Hung, C. M.↗
NASA NTRS1987

Numerical simulation of three-dimensional supersonic inlet flow fields

Supersonic inlet flows with mixed external-internal compressions of an axisymmetric inlet model were computed using a combined implicit-explicit (Beam-Warming-Steger/MacCormack) method for solving the three-dimensional unsteady, compressible Navier-Stokes equations in conservation form. Numerical calculations were made of various flows typically found in supersonic inlets such as shock-wave intersections, flow spillage around the cowl lip, shock-wave/boundary-layer interactions, control of shock-induced flow separation by means of boundary layer bleed, internal normal (terminal) shocks, and the effects of flow incidence. Computed results were compared with available wind tunnel data.

Kawamura, T.↗
NASA NTRS1986

On the inception lengths of swept shock-wave/turbulent boundary-layer interactions

Experimental data are shown for the inception lengths of swept compression corner-generated and fin-generated shock/boundary layer interactions at Mach 2.95. These results are found to correlate on the basis of three different flow regimes. The inception lengths of these flows are dominated by a singularity at the cylindrical/conical boundary for swept corners and by an elongation due to shock wave sweepback for fin interactions. Similarity rules for both Re(delta)and shock generator geometry effects on inception lengths are demonstrated.

Settles, G. S.↗
NASA NTRS1990

Color surface-flow visualization of fin-generated shock wave boundary-layer interactions

Kerosene-lampblack mixtures with addition of a ground colored chalk were used in an experiment on visualizing surface flows of swept shock boundary-layer interactions. The results show that contrasting colors intensify the visualization of different regions of the interaction surface, and help the eye in following the fine streaks to locate the upstream influence. The study confirms observations of the separation occurring at shock strength below accepted values. The superiority of the reported technique over the previous monochrome technique is demonstrated.

Lu, F. K.↗
NASA NTRS1977

Reynolds number effects on shock-wave turbulent boundary-layer interactions - A comparison of numerical and experimental results

An experiment is described that tests and guides computations of a shock-wave turbulent boundary-layer interaction flow over a 20-deg compression corner at Mach 2.85. Numerical solutions of the time-averaged Navier-Stokes equations for the entire flow field, employing various turbulence models, are compared with the data. Each model is critically evaluated by comparisons with the details of the experimental data. Experimental results for the extent of upstream pressure influence and separation location are compared with numerical predictions for a wide range of Reynolds numbers and shock-wave strengths.

Horstman, C. C.↗
NASA NTRS1972

Shock wave-turbulent boundary layer interactions in rectangular channels.

Interaction regions created by the impingement of full span, externally generated, shock waves on a nozzle wall boundary layer were investigated. Incident shock strength was varied to produce unseparated, incipient, and fully separated flow fields. Significant departures from two-dimensionality were observed over the entire range of shock strengths tested and were identified with sidewall and corner boundary layer effects. However, comparisons of present centerline results with published two-dimensional data, obtained under similar test conditions and geometrical constraints, showed excellent agreement (e.g., incipient separation pressure levels, wall pressure distributions, free-interaction, and scale of the interaction region). This raises some question concerning the degree of two-dimensionality achieved in these previous investigations.

Reda, D. C.↗
NASA NTRS1999

Analysis of Unsteady Flow Phenomena: Shock - Vortex and Shock - Boundary Layer Interactions

The interaction of shock waves with vortices has received much attention in the past, mainly because shock-vortex interaction closely models the interaction of a shock wave with the coherent structures of a turbulent flow-field, and is a key feature in the broad-band shock noise for supersonic jets in off-project conditions. Chu and Kovasznay have shown that a weak disturbance in a viscous heat conducting fluid can be decomposed as the sum of three basic modes, namely acoustic, vortical and entropy mode; the interaction of any of these modes with a shock wave gives rise to all three disturbance modes downstream of the shock. The vortical mode is important since it constitutes the basis of the coherent structures that have been observed to dominate turbulence for low- to moderate-flow speed. Hollingsworth et al. have experimentally investigated the interaction of a cylindrical shock-induced starting vortex with a plane normal shock, and have shown that the interaction generates a cylindrical acoustic pulse that exhibits a quadrupolar structure consisting of four alternate compression and expansion regions centered around the transmitted vortex. The investigations of Hollingsworth and Richards have been extended by Dosanjh and Weeks that have analyzed the interaction of a columnar spiral vortex with a normal shock wave, thus obtaining quantitative measurements and confirming the generation of a progressive cylindrical wavefront of alternate compression-expansion nature. Naumann and Hermanns' have experimentally addressed the non-linear aspects of shock-vortex interaction, and have shown that the interaction causes both a diffraction and a reflection of the shock with a pattern consisting of either a regular-or a Mach-reflection depending on the shock and the vortex strengths. An attempt to theoretically explain the production of sound from the shock-vortex interaction was carried out by Ribner. Pao and Salas have numerically studied two-dimensional shock-vortex interactions.

Grasso, Francesco↗
NASA NTRS1992

The hypersonic shock wave-turbulent boundary layer interaction generated by a sharp fin at Mach 8.2

A combined experimental and numerical study has been conducted on the hypersonic shock-wave turbulent-boundary layer interaction at Mach 8.2 generated by a single fin of angles alpha = 10 and 15 deg. Three models are considered: (1) the 3D compressible Reynolds-averaged Navier-Stokes (RANS) equations using the k-epsilon turbulence model, (2) the 3D RANS using the Rodi turbulence model, and (3) the conical RANS using the Baldwin-Lomax algebraic turbulence model. The computations are compared with various experimental data. The computations using models (1) and (2) show quantitatively very similar results and very good agreement with experimental data for surface pressure and skin friction. Comparison with boundary layer profiles of pitot pressure and yaw angle are also generally good, but the peak surface heat transfer is overestimated by up to 48 percent. The effect of the laminar boundary layer on the fin is restricted to the immediate vicinity of the fin surface. Conical calculations using model (3) show substantially poorer agreement with experiment.

Knight, Doyle D.↗
NASA NTRS2000

Separation Control at Flight Reynolds Numbers: Lessons Learned and Future Directions

Active separation control, using periodic excitation, was studied experimentally at high Reynolds numbers. The effects of compressibility, mild sweep, location o excitation slot and steady momentum transfer on the efficacy of the method were identified. Tests conducted at chord Reynolds numbers as high as 40 x 10(exp 6) demonstrated that active control using oscillatory flow excitation can effectively delay flow separation from and reattach separated flow to aerodynamic surfaces at flight conditions. The effective frequencies generate one to four vortices over the controlled region at all times, regardless of the Reynolds number. The vortices are initially amplified by the separated shear-layer, and after initiating reattachment, the strength of the vortices decay as they are convected downstream. Large amplitude, low frequency vortices break down to smaller ones upon introduction at the excitation slot. The effects of steady mass transfer were compared to those of periodic excitation. It was found that steady blowing is significantly inferior to periodic excitation in terms o performance benefits and that the response to steady blowing is abrupt, and therefore undesirable from a control point of view. Steady suction and periodic excitation are comparable in effectiveness and both exhibit a gradual response to changes in the magnitude of the control input. The combination of weak steady suction and periodic excitation is extremely effective while the addition of steady blowing could be detrimental. Compressibility effects are weak as long as separation is not caused by a shock-wave/boundary-layer interaction The undesirable effects of the shock-induced separation could be alleviated by the introduction of periodic excitation upstream of the shock wave, inside the region of supersonic flow. The effects of mild sweep were also studied and periodic excitation was found to be very effective in reattaching three-dimensional separated flow. Scaling laws that correlate 2D and 3D controlled flows were tested and verified. Several performance benefits could be gained by applying the method to existing configurations, but it is expected that the full potential of the method can only be realized through the design of new configurations. A comprehensive, fully turbulent, database was generated in order to guide the development, and enable validation, of candidate unsteady CFD design tools.

Seifert, Avi↗
NASA NTRS2000

Separation Control at Flight Reynolds Numbers: Lessons Learned and Future Directions

Active separation control, using periodic excitation, was studied experimentally at high Reynolds numbers. The effects of compressibility, mild sweep, location of excitation slot and steady momentum transfer on the efficacy of the method were identified. Tests conducted at chord Reynolds numbers as high as 40 x 10(exp 6) demonstrated that active control using oscillatory flow excitation can effectively delay flow separation from, and reattach separated flow to aerodynamic surfaces at flight conditions. The effective frequencies generate one to four vortices over the controlled region at all times, regardless of the Reynolds number. The vortices are initially amplified by the separated shear-layer, and after initiating reattachment, the strength of the vortices decay as they are convected downstream. Large amplitude, low frequency vortices break down to smaller ones upon introduction at the excitation slot. The effects of steady mass transfer were compared to those of periodic excitation. It was found that steady blowing is significantly inferior to periodic excitation in terms of performance benefits and that the response to steady blowing is abrupt, and therefore undesirable from a control point of view. Steady suction and periodic excitation are comparable in effectiveness and both exhibit a gradual response to changes in the magnitude of the control input. The combination of weak steady suction and periodic excitation is extremely effective while the addition of steady blowing could be detrimental. Compressibility effects are weak as long as separation is not caused by a shock-wave/boundary-layer interaction. The undesirable effects of the shock-induced separation could be alleviated by the introduction of periodic excitation upstream of the shock wave, inside the region of supersonic flow. The effects of mild sweep were also studied and periodic excitation was found to be very effective in reattaching three-dimensional separated flow. Scaling laws that correlate 2D and 3D controlled flows were tested and verified. Several performance benefits could be gained by applying the method to existing configurations, but it is expected that the full potential of the method can only be realized through the design of new configurations. A comprehensive, fully turbulent, database was generated in order to guide the development, and enable validation, of candidate unsteady CFD design tools.

Pack, LaTunia G.↗
NASA NTRS1977

Direct measurements of wall shear stress by buried wire gages in a shock-wave boundary-layer interaction region

Detailed measurements of wall shear stress (skin friction) were made with specially developed buried wire gages in the interaction regions of a Mach 2.9 turbulent boundary layer with externally generated shocks. Separation and reattachment points inferred by these measurements support the findings of earlier experiments which used a surface oil flow technique and pitot profile measurements. The measurements further indicate that the boundary layer tends to attain significantly higher skin-friction values downstream of the interaction region as compared to upstream. Comparisons between measured wall shear stress and published results of some theoretical calculation schemes show that the general, but not detailed, behavior is predicted well by such schemes.

Murthy, V. S.↗
NASA NTRS1973

A finite-difference solution for unsteady wave interactions with an application to the expansion tube

An analytical study of the unsteady wave interaction of a shock wave overtaking a previously initiated shock tube flow has been conducted for a real gas by solving a finite-difference representation of the one-dimensional Navier-Stokes equations. This analysis has been used to determine the effect on the available test time of opening the secondary diaphragm in the expansion-tube operating cycle prior to the arrival of the incident shock wave. Special emphasis is placed on determining expansion-tube test-time limitations resulting from a nonuniform entropy distribution occurring during the early test-gas flow due to the varying Mach number of the incident shock wave as it traverses the expansion fan caused by the preopening process. Time distributions of velocity, temperature, pressure, and entropy at various distances from the diaphragm are presented as a function of the time required to open the diaphragm.

Weilmuenster, K. J.↗
NASA NTRS1974

Transmission of singularities through a shock wave and the sound generation

The interaction of a plane shock wave of finite strength with a vortex line, point vortex, doublet or quadrupole of weak strength is studied. Based upon the physical condition that a free vortex line cannot support a pressure difference, rules are established which define the change of the linear intensity of the segment of the vortex line after its passage through the shock. The rules for point vortex, doublet, and quadrupole are then established as limiting cases. These rules can be useful for the construction of the solution of the entire flow field and for its physical interpretation. However, the solution can be obtained directly by the technique developed for shock diffraction problems. Explicit solutions and the associated sound generation are obtained for the passage of a point vortex through the shock wave.

Ting, L.↗
NASA NTRS1991

Three-dimensional shock wave-turbulent boundary layer interactions generated by a sharp fin at Mach 4

This paper describes a combined experimental and theoretical study of three-dimensional swept shock wave-turbulent boundary layer interactions at Mach 4 generated by a sharp fin of angles alpha equals 16 and 20 degrees. The theoretical model is the three-dimensional compressible Reynolds-averaged Navier-Stokes equations with turbulence incorporated through the algebraic eddy viscosity model of Baldwin and Lomax. Previous computations have been performed by Horstman using the Baldwin-Lomax, Cebeci-Smith and Jones Launder models. Computed results for the surface pressure, skin friction and streamline angles are compared with experiment and previous numerical results. The present results display good agreement with experimental data for surface pressure and surface flow direction. All turbulence models fail to accurately predict the peak skin friction. The computed flowfields are in agreement with many of the features of the quasi-conical flowfield model of Settles.

Knight, Doyle D.↗
NASA NTRS2011

Uncertainty Assessments of 2D and Axisymmetric Hypersonic Shock Wave - Turbulent Boundary Layer Interaction Simulations at Compression Corners

This paper is one of a series of five papers in a special session organized by the NASA Fundamental Aeronautics Program that addresses uncertainty assessments for CFD simulations in hypersonic flow. Simulations of a shock emanating from a compression corner and interacting with a fully developed turbulent boundary layer are evaluated herein. Mission relevant conditions at Mach 7 and Mach 14 are defined for a pre-compression ramp of a scramjet powered vehicle. Three compression angles are defined, the smallest to avoid separation losses and the largest to force a separated flow engaging more complicated flow physics. The Baldwin-Lomax and the Cebeci-Smith algebraic models, the one-equation Spalart-Allmaras model with the Catrix-Aupoix compressibility modification and two-equation models including Menter SST, Wilcox k-omega 98, and Wilcox k-omega 06 turbulence models are evaluated. Each model is fully defined herein to preclude any ambiguity regarding model implementation. Comparisons are made to existing experimental data and Van Driest theory to provide preliminary assessment of model form uncertainty. A set of coarse grained uncertainty metrics are defined to capture essential differences among turbulence models. Except for the inability of algebraic models to converge for some separated flows there is no clearly superior model as judged by these metrics. A preliminary metric for the numerical component of uncertainty in shock-turbulent-boundary-layer interactions at compression corners sufficiently steep to cause separation is defined as 55%. This value is a median of differences with experimental data averaged for peak pressure and heating and for extent of separation captured in new, grid-converged solutions presented here. This value is consistent with existing results in a literature review of hypersonic shock-turbulent-boundary-layer interactions by Roy and Blottner and with more recent computations of MacLean.

Gnoffo, Peter A.↗
NASA NTRS1990

Upstream-influence scaling of fin-generated shock wave boundary-layer interactions

An upstream-influence scaling law, previously formulated through analysis of Mach 3 data, has been extended to Mach numbers from 2.5 through 4. For adiabatic, equilibrium, turbulent boundary layers, there is no Mach number effect on the constants in the Reynolds number parameters of this law. In addition, based on local similarity, a new Mach number parameter, namely, the Mach number component of the incoming stream normal to the farfield upstream influence, is proposed. Scaling by either the incoming Mach number normal to the inviscid shock or by the incoming Mach number normal to the farfield upstream influence is equivalent to scaling by the hypersonic similarity parameter.

Lu, Frank K.↗