Results for “RANS” — Page 15

NASA NTRSDate not supplied

Simulation and Modeling of Hypersonic Turbulent Boundary Layers Subject to Adverse Pressure Gradients due to Concave Streamline Curvature

Direct numerical simulations (DNS) of adverse-pressure-gradient turbulent boundary layers over a planar concave wall are presented for a nominal freestream Mach number of 5, with the objective of assessing the limitations of the currently available Reynolds-averaged Navier-Stokes (RANS) models. The wall geometry and flow conditions of the DNS are representative of the experimental data for a Mach 4.9 turbulent boundary layer that was tested on a two-dimensional planar concave wall model in the high-speed blow-down wind tunnel located at the National Aerothermochemistry Laboratory at Texas A&M University (TAMU). The DNS was validated against the experimental results of TAMU for the same flow conditions and wall geometry. An analysis of the DNS datasets was also conducted to provide an assessment of the validity of Morkovin’s hypothesis and the strong Reynolds analog for turbulence subject to mechanical nonequilibrium. In addition to the DNS results, RANS predictions are obtained by using the Baldwin-Lomax (BL), Spalart-Allmaras (SA), and the k - w SST turbulence models. The comparisons between RANS and DNS showed little impact of an adverse pressure gradient on the accuracy of these models, at least up to an incompressible Clauser pressure gradient parameter of beta(sub inc) 1.22. While the Boussinesq assumption provided reasonable predictions for the Reynolds shear stress, it failed to adequately predict the normal components of the Reynolds stress.

turbulent boundary layers↗

NASA NTRSDate not supplied

A Large-Eddy Simulation Of Turbulent Flow Over A Backward Facing Step

Large-eddy simulation (LES) was used to study the turbulent flow over a backward facing step. The simulations examine the details of the turbulent flow’s separated and reattaching regions created by the step geometry. An explicit high-order of accuracy/high resolution finite-difference computational fluid dynamics solver was used for both LES and Reynolds-averaged Navier-Stokes (RANS) simulations. The experimental data from the backward facing step experiment of Driver and Seegmiller was used for comparison. Data presented are derived from a RANS simulation using the Spalart-Allmaras turbulence model and LES simulations using the implicit LES assumption on three different grids of varying resolution. The RANS solution agrees with past work. It does an adequate job of predicting the flowfield and reattachment point, but misses details such as the strength of the recirculating region and magnitudes of the Reynolds stresses. The synthetic eddy method was used to provide a turbulent inflow to the quasi-2D LES domains. For the LES, the coarse grid was of insufficient resolution and under-predicted the skin friction coefficient and over-predicted the normal stresses. The finer grid LES results accurately predict the skin friction coefficient and provide more accurate Reynolds stresses. Triple product velocity correlations are also computed from the LES and the finer grid results did a good job predicting the magnitudes of the curves and the shapes were reasonably represented. It is recommended that future work include investigating the turbulent inflow domain length, width of the quasi-2D domain, and additional grid refinement

turbulence↗

NASA NTRS2021

Transition Analysis for the CRM-NLF Wind Tunnel Configuration using Transport Equation Models and Linear Stability Correlations

Transition models based on auxiliary transport equations augmenting the Reynolds-averaged Navier-Stokes (RANS) framework rely upon transition correlations that were derived from a limited number of low-speed experiments. Furthermore, these models often account for only a subset of the relevant transition mechanisms and/or cannot accurately predict the sensitivity of those mechanisms to the changes in significant flow parameters. A preceding investigation had targeted the assessment of the transport-equation-based transition models in NASA's OVERFLOW 2.3b solver, namely, the amplification factor transport (AFT-2017b) equation model coupled with the Spalart-Allmaras RANS model and the Langtry-Menter transition models (LM2009 without crossflow effects and LM2015 including the modeling of crossflow transition) implemented with Menter’s shear-stress transport equation (SST2003) RANS model. Comparisons with recent measurements at transonic freestream conditions on the Common Research Model with Natural Laminar Flow (CRM-NLF) reinforced our earlier finding that all three of the above models significantly underpredict the reported extent of the laminar flow region over the entire span of the wing, regardless of the dominant instability mechanism(s) underlying the onset of the transition process. The underprediction of the laminar flow extent was attributed to the failure of the above models in accounting for the stabilizing effect of compressibility on the amplification of Tollmien-Schlichting instabilities. Based on previous linear stability studies related to compressibility effects, the present work proposes modifications to the two classes of transition models that reduce to the original form of each model at low subsonic speeds and do not require any nonlocal flow information or additional transport equation(s). The modifications are shown to significantly improve the predicted laminar extent of the flow and compare well against the data from the CRM-NLF experiment. Additionally, a previous assessment of transition prediction based on the dual, nonparallel N -factor method in conjunction with linear parabolized stability equations (PSE) is extended to additional angles of attack to provide the first comprehensive assessment of transition models based on nonparallel disturbance amplification over the CRM-NLF. In general, the transition criterion based on the dual, nonparallel N-factor method with N TS = N CF = 6 is reasonably successful at correlating with the measured transition fronts at R eMAC = 15 million for all angles of attack investigated herein and provides additional validation of the improved predictions from the compressibility-corrected transition models.

CFD modeling↗

NASA NTRS2022

Transition Analysis for the CRM-NLF Wind Tunnel Configuration using Transport Equation Models and Linear Stability Correlations

Transition models based on auxiliary transport equations augmenting the Reynolds-averaged Navier-Stokes (RANS) framework rely upon transition correlations that were derived from a limited number of low-speed experiments. Furthermore, these models often account for only a subset of the relevant transition mechanisms and/or cannot accurately predict the sensitivity of those mechanisms to the changes in significant flow parameters. A preceding investigation had targeted the assessment of the transport-equation-based transition models in NASA's OVERFLOW 2.3b solver, namely, the amplification factor transport (AFT-2017b) equation model coupled with the Spalart-Allmaras RANS model and the Langtry-Menter transition models (LM2009 without crossflow effects and LM2015 including the modeling of crossflow transition) implemented with Menter’s shear-stress transport equation (SST2003) RANS model. Comparisons with recent measurements at transonic freestream conditions on the Common Research Model with Natural Laminar Flow (CRM-NLF) reinforced our earlier finding that all three of the above models significantly underpredict the reported extent of the laminar flow region over the entire span of the wing, regardless of the dominant instability mechanism(s) underlying the onset of the transition process. The underprediction of the laminar flow extent was attributed to the failure of the above models in accounting for the stabilizing effect of compressibility on the amplification of Tollmien-Schlichting instabilities. Based on previous linear stability studies related to compressibility effects, the present work proposes modifications to the two classes of transition models that reduce to the original form of each model at low subsonic speeds and do not require any nonlocal flow information or additional transport equation(s). The modifications are shown to significantly improve the predicted laminar extent of the flow and compare well against the data from the CRM-NLF experiment. Additionally, a previous assessment of transition prediction based on the dual, nonparallel N -factor method in conjunction with linear parabolized stability equations (PSE) is extended to additional angles of attack to provide the first comprehensive assessment of transition models based on nonparallel disturbance amplification over the CRM-NLF. In general, the transition criterion based on the dual, nonparallel N-factor method with N TS = N CF = 6 is reasonably successful at correlating with the measured transition fronts at R eMAC = 15 million for all angles of attack investigated herein and provides additional validation of the improved predictions from the compressibility-corrected transition models.

CFD modeling↗

NASA NTRSDate not supplied

A Large-Eddy Simulation Of Turbulent Flow Over A Backward Facing Step

Large-eddy simulation (LES) was used to study the turbulent flow over a backward facing step. The simulations examine the details of the turbulent flow's separated and reattaching regions created by the step geometry. An explicit high-order of accuracy/high resolution finite-difference computational fluid dynamics solver was used for both LES and Reynolds-averaged Navier-Stokes (RANS) simulations. The experimental data from the backward facing step experiment of Driver and Seegmiller was used for comparison. Data presented are derived from a RANS simulation using the Spalart-Allmaras turbulence model and LES simulations using the implict LES assumption on three different grids of varying resolution. The RANS solution agrees with past work. It does an adequate job of predicting the flowfield and reattachment point, but misses details such as the strength of the recirculating region and magnitudes of the Reynolds stresses. The synthetic eddy method was used to provide a turbulent inflow to the quasi-2D LES domains. For the LES, the coarse grid was of insufficient resolution and under-predicted the skin friction coefficient and over-predicted the normal stresses. The finer grid LES results accurately predict the skin friction coefficient and provide more accurate Reynolds stresses. Triple product velocity correlations are also computed from the LES and the finer grid results did a good job predicting the magnitudes of the curves and the shapes were reasonably represented. It is recommended that future work include investigating the turbulent inflow domain length, width of the quasi-2D domain, and additional grid refinement.

turbulence↗

NASA NTRSDate not supplied

Numerical Investigation of the Effect of Trailing Edge Thickness of Simulated CMC Blades on Loss Profiles

To understand such an aerodynamic characteristic of the CMC blades, we numerically simulated three different CMC blades with varying trailing edge thicknesses. We utilized both Large Eddy simulation (LES) with the dynamic subgrid closure as well a recently implemented Reynolds-averaged Navier-Stokes (RANS) coupled with an intermittency function-based transition model. We considered two sets of experimental test points with different Reynolds numbers at a given high-free stream turbulence range (Tu=~10-13%). The LES was previously validated by comparing with experimental data. We validated the RANS transition model against the ERCOFTAC experimental zero-pressure gradient smooth flat plate boundary layer at low- and high freestream turbulence offered by the experimental data of the Stripf’s for a turbine blade. We confirmed that the predicted skin friction and the heat flux agree well with the data. Finally, we computed the predicted pressure loading profiles, total loss distributions, and integrated loss of the three different CMC blades and made comparisons against the experimental data acquired at NASA Glenn Transonic Turbine Blade Cascade Rig. Our paper will present the aforementioned results and discuss the ability of LES and RANS model of our choice to predict salient aerodynamic characteristics of the blades with the various trailing edge thickness effects.

LES↗

NASA NTRSDate not supplied

Numerical Investigation of the Effect of Trailing Edge Thickness of Simulated CMC Blades on Loss Profiles

To understand such an aerodynamic characteristic of the CMC blades, we numerically simulated three different CMC blades with varying trailing edge thicknesses. We utilized both Large Eddy simulation (LES) with the dynamic subgrid closure as well a recently implemented Reynolds-averaged Navier-Stokes (RANS) coupled with an intermittency function-based transition model. We considered two sets of experimental test points with different Reynolds numbers at a given high-free stream turbulence range (Tu=~10-13%). The LES was previously validated by comparing with experimental data. We validated the RANS transition model against the ERCOFTAC experimental zero-pressure gradient smooth flat plate boundary layer at low- and high freestream turbulence offered by the experimental data of the Stripf’s for a turbine blade. We confirmed that the predicted skin friction and the heat flux agree well with the data. Finally, we computed the predicted pressure loading profiles, total loss distributions, and integrated loss of the three different CMC blades and made comparisons against the experimental data acquired at NASA Glenn Transonic Turbine Blade Cascade Rig. Our paper will present the aforementioned results and discuss the ability of LES and RANS model of our choice to predict salient aerodynamic characteristics of the blades with the various trailing edge thickness effects.

LES↗

NASA NTRSDate not supplied

CFD Predictions of Fluctuating Pressure Environments on NASA’s SLS Ascent Unsteady Aerodynamics Wind Tunnel Test

This paper details work that is being conducted on predicting fluctuating pressure environments on NASA launch vehicles using computational fluid dynamics (CFD). The accurate characterization of these aeroacoustics environments is necessary in the analysis of vehicle structural health and aerodynamic performance and in the vehicle design process. High-fidelity simulations of the unsteady flow over NASA’s SLS Ascent Unsteady Aerodynamics wind tunnel Test (AUAT) using the hybrid Reynolds-averaged Navier-Stokes (RANS)-large eddy simulations (LES) methodologies in Mississippi States’ Loci/CHEM solver are presented. The two available methods, Nelson-Nichols and dynamic hybrid RANS-LES (DHRL), are compared head-to-head on identical grids at two Mach numbers. At the high-subsonic Mach number, locally supersonic flow expanding over a shoulder induces a separation-reattachment system that is predicted poorly by the Nelson-Nichols method due to an under-prediction in unsteady content. The DHRL solution predicts the spatial extent and frequency domain response of this system well but under-predicts the peak noise levels due to a delay in the RANS-to-LES transition. At the low-supersonic Mach number, compression corner dynamics dominate the unsteady flow. While the Nelson Nichols solution captures this phenomenon well, another solution on a refined grid indicates that some model stress depletion is occurring. The DHRL solution again performs well at this Mach number and matches the wind tunnel data fairly closely, but perhaps most impressively, is fairly agnostic to increasing grid resolution. The findings in this paper are expected to be generally applicable and will be used to guide the prediction of aeroacoustics environments of other NASA launch vehicles.

CFD↗

NASA NTRS2024

Turbulence Model Validation through Joint Experimental / Computational Studies of Separated Flow Over a Three-Dimensional Tapered Bump: Part II - Computational Investigation

This report serves as documentation of activities related to Computational Fluid Dynamics (CFD) analysis applied to the Smooth Body Separation Experiment designed to produce validation-quality experimental data from wind-tunnel tests performed at the University of Notre Dame. All CFD analysis utilized the Boeing CFD (BCFD) flow solver. BCFD was used to analyze flow over the Boeing Speed Bump with second-order accuracy in space and time. Inviscid fluxes were computed using the HLLE scheme for steady-state simulations, and the Low-Dissipation Roe scheme for time-accurate simulations. The working fluid was modeled as calorically perfect air using Sutherland's law for viscosity. Thermal diffusivity was determined by assuming a constant molecular Prandtl number of 0.72, and a turbulent Prandtl number of 0.9. Reynolds Averaged Navier-Stokes (RANS) simulations were conducted using the one-equation Spalart-Allmaras turbulence model with rotation correction3 and the quadratic constitutive relation (SA-RC-QCR), as well as Menter's two-equation, Shear-Stress Transport (SST) model. Time-accurate computations were conducted using Delayed Detached eddy Simulation (DDES) with the one-equation RANS model, and Large Eddy Stress balance (LESb) with the two-equation RANS model. Implicit dual-time stepping was used to achieve second-order temporal accuracy. The experimental investigation conducted during the course of this study is described in detail in an accompanying report.

Flow separation↗

NASA NTRSDate not supplied

VEG-05 Tomato Crop Testing on the International Space Station

Production of fresh, nutritious, and tasty produce for astronauts during spaceflight may provide health-promoting, bioavailable nutrients, enhance the dietary experience, and reduce menu fatigue as we move into longer-duration missions. Growing and caring for plants may also reduce the psychological stresses associated with spaceflight and enhance connection to Earth. A diversity of crops will be required to provide nutrition, variety, and resiliency, however requirements for consistent growth under spaceflight environmental conditions remain unclear. VEG-05 is part of a series of experiments with pick-and-eat salad crops to better define best practices for crop production in space. VEG-05 and predecessor experiments VEG-04A and VEG-04B, grew salad crops in the Veggie vegetable production facilities on the International Space Station using different lighting treatments. In VEG-05 we grew ‘Red Robin’ dwarf cherry tomatoes under two different red: blue lighting spectra. Light can impact the growth habit, yield, nutritional composition, microbial levels, and even flavor attributes within crops, and our goal was to assess these characteristics in ‘Red Robin’ tomatoes during VEG-05. Considerable pre-flight verification testing was performed prior to launch in Nov. 2022. Prior to the flight and ground experiments, lighting in both Veggie units on ISS was measured and lights were standardized between flight and ground hardware. VEG-05 flight operations ran between December 2022 and March 2023, with a ground control initially 48 hours delayed. Due to environmental challenges of very low humidity during the first week of the experiment, seed germination was low for both flight and ground plants. The flight experiment ultimately had 4 - 5 plants per treatment out of the planned 6 plants, but the initial ground control had only three plants in one treatment and none in the other, so this ground control was restarted at the beginning of Feb. 2023 and ran through May, with successful growth of all 12 plants. Both flight and ground control ran 100 days, with harvests of fruit at day 83, day 90, and day 100. Flight plants had uneven growth, and following the early drying events, excess water was frequently observed, which led to a variety of plant stress responses including uneven plant growth, excess adventitious root formation, flower and fruit abortion, and visible microbial growth. In total, from the five surviving red-rich lighted plants, only 5 ripe fruit were produced, and from the four surviving blue-rich lighted plants, 10 fruit were produced with only 6 of these ripe by day 100. Because of the small fruit number and the unsatisfactory growth, crew members were not allowed to consume the tomatoes, and all fruit, as well as large branches with leaves, samples of the adventitious roots, two plant rooting pillows from each treatment, microbial sampling swabs, and some water samples were returned for analysis. Because of the small sample sizes and factors affecting growth on the ISS, objectives of assessing light quality effect (red: blue light treatments) will not be achieved. Revised objectives of this study include to compare stressed flight plants with normal ground plants to determine the impact of plant overwatering stress in space on food safety and the plant microbial community, to determine nutrient content changes in fruit and leaves from stressed plants, and to evaluate stress metabolism changes in returned tissue by transcriptomic analysis. Postflight analysis is underway with the following analyses being conducted: A. culturable microbiology and food safety as well as molecular microbial community analysis of 1. ripe fruit, 2. leaves, stems, and adventitious roots, 3. pillow components (roots, wicks, and substrates), 4. swabs, and 5. water samples from root mats before and after growth. B. transcriptomics of leaf tissue and adventitious roots, and C. elemental analysis of leaf tissue. If sufficient tissue remains elemental analyses will also be conducted on fruit. While not generating the desired information on spaceflight growth responses of healthy crops, our team is hopeful that these analyses will shed light on tomato responses to stress in this environment as plant overwatering stress is a mission-relevant condition that could occur in future space crop growth systems. This research was co-funded by the Human Research Program and Space Biology (MTL#1075) in the ILSRA 2015 NRA call.

Gioia D. Massa↗

NASA NTRSDate not supplied

High-Fidelity CFD Verification Workshop 2024 Summary: Spalart-Allmaras QCR2000-R Turbulence Model

This paper summarizes solutions submitted for the Reynolds-averaged Navier-Stokes (RANS) test suite of the High-Fidelity CFD Verification Workshop. The goal of the workshop is to establish standards for verification of computational fluid dynamics (CFD) approaches to simulations of steady and unsteady turbulent flows. The RANS verification studies focus on a one-equation Spalart-Allmaras model with quadratic constitutive relation and rotation correction, SA-neg-QCR2000-R. The verification test cases are a two-dimensional subsonic flow around a Joukowski airfoil, a three-dimensional subsonic flow around an extruded NACA 0012 wing in a tunnel, and a subsonic flow around a wing-body configuration developed for verification of solvers participating in the 5 𝑡 ℎ High-Lift Prediction Workshop. The turbulencemodel formulation, geometry, flow conditions, grids, and reference solutions are described in detail. Solutions for the test cases are computed by seven established CFD solvers on adaptedand fixed-grid families using different discretization approaches. While some noticeable differences between solutions remain, the results achieved by contributing solvers show that different solutions computed for the same RANS model on different grid families can converge to a common limit with grid refinement. The apparent requirements for grid convergence are a well designed family of grids that provide sufficient resolution in important areas and a strong solver capable of deep iterative convergence on each grid. For each test case in the study, the variation between aerodynamic forces computed by different solvers on the finest grids of different families is less than 2%.

Boris Diskin↗

NASA NTRSDate not supplied

Computational Analysis of a Boundary-Layer Ingesting Tailcone Thruster Configuration Within the National Transonic Facility Using the LAVA Solver

Boundary-layer ingesting (BLI) propulsion systems are one of the many technologies currently under investigation within the aerospace community to meet NASA’s Advanced Air Transport Technology project goal of a sustainable future in aviation. To that end, an experimental campaign was conducted in the National Transonic Facility (NTF) to study the propulsion-airframe integration effects of the Boundary-Layer Ingesting Tailcone System installed in the aft portion of a 2.7% scale design of the NASA Common Research Model (CRM). This test was accompanied by a numerical simulation effort using the Launch, Ascent, and Vehicle Aerodynamics (LAVA) solver, to validate the applicability of current best-practice Reynolds-averaged Navier Stokes (RANS) models in accurately predicting the relevant flow-physics in free-air. A total of 205 steady RANS simulations were performed using LAVA, covering the range of conditions present in the NTF test matrix. Flow conditions ranged from 5- to 15-million Reynolds number, Mach numbers of 0.75, 0.80 and 0.85, and angles-of-attack between –3° and 4°. Four different mass-flow plugs were also tested to assess propulsor operating condition effects. Sensitivity to these flow conditions are analyzed in detail, especially in terms of the nacelle flow distortion which was the main subject of the study. Aerodynamic load coefficients, aftbody boundary-layer measurements and fuselage pressure tap results are also discussed, providing a wide range of validation results from this experimental campaign. This validation effort shows that current best-practices using RANS models within the LAVA solver flow solver are well suited for predicting the inlet flow distortion characteristics of novel aircraft configurations employing BLI at the aft end of the fuselage.

AATT↗

NASA NTRSDate not supplied

Computational Analysis of a Boundary Layer Ingesting Tailcone Thruster Configuration Using the LAVA Curvilinear Solver

Boundary layer ingesting (BLI) propulsion systems are one of the many technologies currently under investigation within the aerospace community to meet NASA's Advanced Air Transport Technology project goal of a sustainable future in aviation. To that end, an experimental campaign was conducted in the National Transonic Facility (NTF) wind tunnel to study the propulsion-airframe integration effects of the Boundary Layer Ingesting Tailcone System installed in the aft portion of a 2.7% scale design of the NASA Common Research Model (CRM). This test was accompanied by a numerical simulation effort using the Launch, Ascent, and Vehicle Aerodynamics (LAVA) curvilinear solver to validate the applicability of current best-practice Reynolds-Averaged Navier-Stokes (RANS) models in accurately predicting the relevant flow physics in free-air. A total of 205 steady RANS simulations were performed using LAVA, covering the range of conditions present in the NTF test matrix. Flow conditions ranged from 5- to 15-million Reynolds number, Mach numbers of 0.75, 0.80 and 0.85, and angles of attack between -3 and 4 degrees. Four different mass-flow plugs were also tested to assess propulsor operating condition effects. Sensitivity to these flow conditions is analyzed in detail, especially in terms of the nacelle flow distortion which was the main subject of the study. Aerodynamic load coefficients, aft body boundary layer measurements and fuselage pressure tap results are also discussed, providing a wide range of validation results from this experimental campaign. This validation effort shows that current best-practices using RANS models within the LAVA curvilinear solver flow solver are well suited for predicting the inlet flow distortion characteristics of novel aircraft configurations employing BLI at the aft end of the fuselage. This talk will cover the combined experimental and numerical efforts that resulted from this BLI-focused investigation.

ARMD↗

NASA NTRSDate not supplied

Transition Prediction for the 30P30N Airfoil and the CRM-HL using FUN3D

The ability to accurately model transition over high-lift configurations can lead to improved agreement between stationary Reynolds-Averaged Navier-Stokes (RANS) computations and experimental measurements. In this work, selected transport-equation-based RANS models for transition prediction in the NASA FUN3D flow solver are used to simulate flow over the 30P30N three-element airfoil and the High-Lift Common Research Model (CRM-HL). The primary RANS-based transition model is the Langtry-Menter (LM) 𝜸-Re𝜽𝒕 model coupled with the Menter shear-stress transport model. Additionally, the existing capability for transition prediction based on linear stability correlations is used to allow the modeling of transition over multiple elements of the 30P30N configuration. This approach pairs an algebraic transition model with the Spalart-Allmaras (SA) turbulence model that relies on an imposed transition location in FUN3D and the parabolized stability equations as implemented in the LASTRAC code. Predictions based on these different transition prediction approaches and models are compared with each other, experimental data, and previous simulations by evaluating the lift and drag coefficients, the surface-pressure/skin-friction distributions, and the locations of transition onset. Results are presented for multiple angles of attack for the 30P30N airfoil and CRM-HL. For the CRM-HL, a grid resolution study is performed for the LM transition model and the SA turbulence model.

High Lift↗

NASA NTRSDate not supplied

Validation Experiments for Turbulent Separation over an Axisymmetric Body of Revolution

Historically, the flow physics involved with most turbulent separated flows have presented fundamental challenges to validating numerical approaches. As recognized by the CFD Vision 2030 study commissioned by NASA, validation of Reynolds-averaged Navier-Stokes (RANS) models and other scale-resolving methods for turbulent separated flow requires data from advanced, high-fidelity experiments designed specifically for CFD implementation. In accordance with this effort, a new test platform, referred to as the NASA Axisymmetric Afterbody, was designed to obtain detailed measurements of the flow field undergoing a smooth, adverse pressure gradient induced separation for a fixed Reynolds number, Re = 180,000. The parametric body offers a range of flow states progressing from fully attached, to incipient separation, and finally to small-scale separated flow based on variable afterbody geometries. In an initial effort to evaluate RANS turbulence model capabilities, the present configurations of the axisymmetric model host a mild adverse pressure gradient over the contoured boattail section, inducing incipient turbulent separation, as well as a slightly larger adverse pressure gradient, inducing a small-scale region of turbulent separation. Experiments include steady pressure measurements and 2-D PIV to provide the preliminary dataset for simulation studies, which examine the effect of variable grid domains and RANS turbulence models. This is done in an effort to understand and evaluate the critical variability between solutions for the present model configurations. Results indicate potential discrepancies may be due to the effect of the square tunnel test section walls, relatively large blockage ratio, and slight variability in reference parameters. Ongoing work will focus on higher fidelity experimental campaigns to obtain surface flow visualizations and Stereo-Particle Image Velocimetry (SPIV) to deliver higher spatial resolution of the three-dimensional flow field to aid turbulence modelers.

Validation↗

NASA NTRSDate not supplied

High-Fidelity Aeropropulsive Assessment of Distributed Electric Propulsion and Boundary Layer Ingestion for the SUSAN Electrofan

This paper presents a high-fidelity aeropropulsive assessment of the SUSAN Electrofan’s distributed electric propulsion (DEP) and boundary layer ingestion (BLI) aft fuselage turbofan technologies. This is achieved through the application of computational tools for aerodynamic and aeropropulsive design and analysis based on the Reynolds-averaged Navier-Stokes (RANS) equations. Representative aircraft models are first developed in 3D for the SUSAN Electrofan concept, a non-DEP variant, and a year 2020 technology level reference aircraft based on the Boeing 737-8. These include airframes developed through the application of RANS-based aerodynamic shape optimization, with the objective of drag minimization at cruise while subject to constant lift and zero pitching moment constraints. Wing propulsors are also included and modeled as free-flying ducted fans. These are developed through RANS-based aeropropulsive shape optimization, with the objective of shaft power minimization while subject to constant net thrust and maximum fan face Mach number constraints. An iterative power balance method is then used to trim each of the decoupled aircraft configurations, providing estimates of relative aerodynamic performance, shaft power, and range efficiency. Results also include power on and off analyses, which indicate reduced thrust-induced drag for the SUSAN Electrofan’s DEP and BLI aft fuselage turbofan propulsors when compared to those of the Boeing 737-8-like reference aircraft.

CAS↗

DOE OSTI2025

Summary Report Of The FY25 Computational Fluid Dynamics Verification And Validation Exercises In The Advanced Reactor Technologies - Gas-cooled Reactor Program

Verification and Validation (V&V) of numerical tools is critical for ensuring reasonable predictions during design, safety analysis, and licensing. Recent work in the Advanced Reactor Technologies - Gas-cooled Reactor (ART-GCR) program has focused on V&V of common Computational Fluid Dynamics (CFD) tools that are used within the Untied States. This report presents an update on these CFD V&V activities. These Generation IV Forum (GIF) Very High Temperature Reactor (VHTR) Computational Methods, Validation, and Benchmarking (CMVB) is an international organization dedicated to the verification and validation of High Temperature Gas-Cooled Reactor (HTGR) simulation tools. Participation in the CMVB provides additional value to the V&V activities, as it allows for access to a wider range of data, and provides valuable benchmarking exercises. Three HTGR phenomena are targeted: Reactor Cavity Cooling System (RCCS) performance, core bypass flow, and lower plenum mixing. Simulations of the University of Wisconsin-Madison (UW-Madison) RCCS facilities are performed with Reynolds Averaged Navier-Stokes (RANS) in StarCCM+. Results are compared for both forced and natural convection conditions, with both exhibiting good agreement with experimental measurements. The Idaho National Laboratory (INL) matched index of refraction (MIR) and Korean Atomic Energy Research Institute (KAERI) bypass flow expeirments are used to validation CFD predictions of bypass flow. Simulations are performed with RANS in StarCCM+ and with Large Eddy Simulation (LES) in NekRS. Finally, preliminary simulations of the Institute of Nuclear and New Energy Technology (INET) lower plenum mixing facilities are presented. Initial work has developed models with LES, RANS, and porous media models. These preliminary models are presented and compared to each other to gauge differences in predictions with each of the three methods.

and Benchmarking (CMVB)↗

DOE OSTI2025

Simulations of Bypass Flow in Prismatic VHTRs

In prismatic Very-High Temperature Reactors (VHTRs), gaps occur between neighboring fuel assemblies referred to as bypass gaps. This work aims to measure the flow distribution between the bypass gaps between neighboring assemblies and the coolant channels within the assemblies. Computational fluid dynamics (CFD) was done using Reynolds-Averaged Navier Stokes (RANS) modeling in STAR-CCM+ to assess the ability of RANS models to accurately capture this phenomena. The RANS results were compared to experimental worked performed by Seoul National University (SNU) and Korea Atomic Energy Research Institute (KAERI) for validation. The CFD results showed good comparison with the experimental data available from SNU and flow split was characterized for multiple configurations, inlet mass flow rates, and bypass gap sizes.

22 - GENERAL STUDIES OF NUCLEAR REACTORS↗