Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “QUARTZ”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

Shock Hugoniot and temperature data for polystyrene obtained with quartz standard

Equation-of-state data, not only pressure and density but also temperature, for polystyrene (CH) are obtained up to 510 GPa. The region investigated in this work corresponds to an intermediate region, bridging a large gap between available gas-gun data below 60 GPa and laser shock data above 500 GPa. The Hugoniot parameters and shock temperature were simultaneously determined by using optical velocimeters and pyrometers as the diagnostic tools and the {alpha}-quartz as a new standard material. The CH Hugoniot obtained tends to become stiffer than a semiempirical chemical theoretical model predictions at ultrahigh pressures but is consistent with other models and available experimental data.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Si nanocrystal p-i-n diodes fabricated on quartz substrates for third generation solar cell applications

We fabricated p-i-n diodes by sputtering alternating layers of silicon dioxide and silicon rich oxide with a nominal atomic ratio O/Si=0.7 onto quartz substrates with in situ boron for p-type and phosphorus for n-type doping. After crystallization, dark and illuminated I-V characteristics show a diode behavior with an open circuit voltage of 373 mV. Due to the thinness of the layers and their corresponding high resistivity, lateral current flow results in severe current crowding. This effect is taken into account when extracting the electronic bandgap based on temperature dependent diode I-V measurements.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Quartz crystal microbalance-based system for high-sensitivity differential sputter yield measurements

We present a quartz crystal microbalance-based system for high sensitivity differential sputter yield measurements of different target materials due to ion bombardment. The differential sputter yields can be integrated to find total yields. Possible ion beam conditions include ion energies in the range of 30-350 eV and incidence angles of 0 deg. - 70 deg. from normal. A four-grid ion optics system is used to achieve a collimated ion beam at low energy (<100 eV) and a two-grid ion optics is used for higher energies (up to 750 eV). A complementary weight loss approach is also used to measure total sputter yields. Validation experiments are presented that confirm high sensitivity and accuracy of sputter yield measurements.

36 MATERIALS SCIENCE↗

Quartz tube extensometer for observation of Earth tides and local tectonic deformations at the Sopronbanfalva Geodynamic Observatory, Hungary

In May 1990, a quartz tube extensometer was installed in the Sopronbanfalva Geodynamic Observatory of the Geodetic and Geophysical Research Institute (GGRI) of the Hungarian Academy of Sciences for recording Earth tides and recent tectonic movements. The paper describes the construction of the extensometer and a portable calibrator used for the in situ calibration of the instrument. The extensometer is very sensitive. Its scale factor is 2.093{+-}0.032 nm/mV according to the highly precise calibration method developed at the GGRI. Since the stability of extensometers is strongly influenced by the geological structure and properties of the rocks in the vicinity of the recording site, the observatory instrument system was tested by coherence analysis between theoretical (as the input signal) and measured tidal data series (as the output signal). In the semidiurnal tidal frequency band the coherence is better than 0.95, while in the diurnal band it is about 0.8. Probably this is due to the fact that the noise is higher in the diurnal band (0.4-0.5 nstr) than in the semidiurnal band (0.19-0.22 nstr). Coherence analysis between theoretical and measured data corrected for barometric changes yielded a small improvement of coherence in both frequency bands, while using temperature data correction, no observable improvement was obtained. Results of the tidal analysis also show that the observatory instrument system is suitable for recording very small tectonic movements. The 18 years of continuous data series measured by the extensometer prove the high quality of the extensometer. On the basis of investigations, it was pointed out that further efforts should be done to improve the barometric correction method and that correction for ocean load, as well as considering topographic and cavity effects are necessary to increase the accuracy of determining tidal parameters.

58 GEOSCIENCES↗

A two-temperature model of radiation damage in {alpha}-quartz

Two-temperature models are used to represent the physics of the interaction between atoms and electrons during thermal transients such as radiation damage, laser heating, and cascade simulations. We introduce a two-temperature model applied to an insulator, {alpha}-quartz, to model heat deposition in a SiO{sub 2} lattice. Our model of the SiO{sub 2} electronic subsystem is based on quantum simulations of the electronic response in a SiO{sub 2} repeat cell. We observe how the parametrization of the electronic subsystem impacts the degree of permanent amorphization of the lattice, especially compared to a metallic electronic subsystem. The parametrization of the insulator electronic subsystem has a significant effect on the amount of residual defects in the crystal after 10 ps. While recognizing that more development in the application of two-temperature models to insulators is needed, we argue that the inclusion of a simple electronic subsystem substantially improves the realism of such radiation damage simulations.

36 MATERIALS SCIENCE↗

Frequency-shift vs phase-shift characterization of in-liquid quartz crystal microbalance applications

The improvement of sensitivity in quartz crystal microbalance (QCM) applications has been addressed in the last decades by increasing the sensor fundamental frequency, following the increment of the frequency/mass sensitivity with the square of frequency predicted by Sauerbrey. However, this sensitivity improvement has not been completely transferred in terms of resolution. The decrease of frequency stability due to the increase of the phase noise, particularly in oscillators, made impossible to reach the expected resolution. A new concept of sensor characterization at constant frequency has been recently proposed. The validation of the new concept is presented in this work. An immunosensor application for the detection of a low molecular weight contaminant, the insecticide carbaryl, has been chosen for the validation. An, in principle, improved version of a balanced-bridge oscillator is validated for its use in liquids, and applied for the frequency shift characterization of the QCM immunosensor application. The classical frequency shift characterization is compared with the new phase-shift characterization concept and system proposed.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Quartz crystal microbalance based on passive frequency to voltage converter

In dynamics of evaporation or drying of microdrops from a solid surface, a faster and precise quartz crystal microbalance (QCM) is needed. The fast QCM based on frequency to voltage converter is an attractive and powerful tool in the investigation of the dynamic regime of evaporation to translate the frequency shift in terms of a continuous voltage change. The frequency shift monitoring in fast QCM applications is a real challenge for electronic processing interface. Originally developed as a frequency shift processing interface, this novel passive frequency to voltage converter can produce faster, stable, and accurate results in regard to the QCM sensor behavior. In this article, the concept and circuit of passive frequency to voltage converter will be explained followed by static and dynamic characterization. Experimental results of microdrops evaporation will be given.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Thermoelastic investigation of a quartz tuning fork used in infrared spectroscopy

The performances of quartz tuning forks (QTF) used in infrared spectroscopy for pollutant detection are investigated. The transduction between light and QTF vibration is elucidated, thanks to QTF encapsulation under vacuum. From the sensitivity enhancement which is obtained, we conclude that their interaction is photo-thermoelastic rather than photo-thermoacoustic. A mapping of the local sensitivity of the QTF is obtained by scanning its faces with the excitation probe beam. The comparison between the signal mapping and the theoretical strain mapping indicates that the most efficient areas of the QTF correspond to the areas where the strain or stress is the highest.

36 MATERIALS SCIENCE↗

Giant g-factors of natural impurities in synthetic quartz

We report the observation of g-factors of natural paramagnetic impurities in a pure synthetic quartz crystal at milli-Kelvin temperatures. Measurements are made by performing spectroscopy using multiple high-Q whispering gallery modes sustained in the crystal. Extreme sensitivity of the method at low temperatures allows the determination of natural residual impurities introduced during the crystal growth. We observe g-factors that significantly differ from integer multiples of the electron g-factor in vacuum, and with values of up to 7.6, which reveals much stronger coupling between impurities and the crystal lattice than in previous studies. Both substitutional and interstitial ions are proposed as candidates for the observed interactions.

36 MATERIALS SCIENCE↗

Hydrogen peroxide detection with quartz-enhanced photoacoustic spectroscopy using a distributed-feedback quantum cascade laser

A quartz-enhanced photoacoustic spectroscopy sensor system was developed for the sensitive detection of hydrogen peroxide (H{sub 2}O{sub 2}) using its absorption transitions in the v{sub 6} fundamental band at ∼7.73 μm. The recent availability of distributed-feedback quantum cascade lasers provides convenient access to a strong H{sub 2}O{sub 2} absorption line located at 1295.55 cm{sup −1}. Sensor calibration was performed by means of a water bubbler that generated titrated average H{sub 2}O{sub 2} vapor concentrations. A minimum detection limit of 12 parts per billion (ppb) corresponding to a normalized noise equivalent absorption coefficient of 4.6 × 10{sup −9} cm{sup −1}W/Hz{sup 1/2} was achieved with an averaging time of 100 s.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

First-principles simulation of the optical response of bulk and thin-film α-quartz irradiated with an ultrashort intense laser pulse

A computational method based on a first-principles multiscale simulation has been used for calculating the optical response and the ablation threshold of an optical material irradiated with an ultrashort intense laser pulse. The method employs Maxwell's equations to describe laser pulse propagation and time-dependent density functional theory to describe the generation of conduction band electrons in an optical medium. Optical properties, such as reflectance and absorption, were investigated for laser intensities in the range 10{sup 10} W/cm{sup 2} to 2 × 10{sup 15} W/cm{sup 2} based on the theory of generation and spatial distribution of the conduction band electrons. The method was applied to investigate the changes in the optical reflectance of α-quartz bulk, half-wavelength thin-film, and quarter-wavelength thin-film and to estimate their ablation thresholds. Despite the adiabatic local density approximation used in calculating the exchange–correlation potential, the reflectance and the ablation threshold obtained from our method agree well with the previous theoretical and experimental results. The method can be applied to estimate the ablation thresholds for optical materials, in general. The ablation threshold data can be used to design ultra-broadband high-damage-threshold coating structures.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Impact of contact and access resistances in graphene field-effect transistors on quartz substrates for radio frequency applications

High-frequency performance of graphene field-effect transistors (GFETs) has been limited largely by parasitic resistances, including contact resistance (R{sub C}) and access resistance (R{sub A}). Measurement of short-channel (500 nm) GFETs with short (200 nm) spin-on-doped source/drain access regions reveals negligible change in transit frequency (f{sub T}) after doping, as compared to ∼23% f{sub T} improvement for similarly sized undoped GFETs measured at low temperature, underscoring the impact of R{sub C} on high-frequency performance. DC measurements of undoped/doped short and long-channel GFETs highlight the increasing impact of R{sub A} for larger GFETs. Additionally, parasitic capacitances were minimized by device fabrication using graphene transferred onto low-capacitance quartz substrates.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Nanopipette combined with quartz tuning fork-atomic force microscope for force spectroscopy/microscopy and liquid delivery-based nanofabrication

This paper introduces a nanopipette combined with a quartz tuning fork-atomic force microscope system (nanopipette/QTF-AFM), and describes experimental and theoretical investigations of the nanoscale materials used. The system offers several advantages over conventional cantilever-based AFM and QTF-AFM systems, including simple control of the quality factor based on the contact position of the QTF, easy variation of the effective tip diameter, electrical detection, on-demand delivery and patterning of various solutions, and in situ surface characterization after patterning. This tool enables nanoscale liquid delivery and nanofabrication processes without damaging the apex of the tip in various environments, and also offers force spectroscopy and microscopy capabilities.

36 MATERIALS SCIENCE↗

Intracavity quartz-enhanced photoacoustic sensor

We report on a spectroscopic technique named intracavity quartz-enhanced photoacoustic spectroscopy (I-QEPAS) employed for sensitive trace-gas detection in the mid-infrared spectral region. It is based on a combination of QEPAS with a buildup optical cavity. The sensor includes a distributed feedback quantum cascade laser emitting at 4.33 μm. We achieved a laser optical power buildup factor of ∼500, which corresponds to an intracavity laser power of ∼0.75 W. CO{sub 2} has been selected as the target molecule for the I-QEPAS demonstration. We achieved a detection sensitivity of 300 parts per trillion for 4 s integration time, corresponding to a noise equivalent absorption coefficient of 1.4 × 10{sup −8} cm{sup −1} and a normalized noise-equivalent absorption of 3.2 × 10{sup −10} W cm{sup −1} Hz{sup −1/2}.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Evidence of a Love wave bandgap in a quartz substrate coated with a phononic thin layer

This paper presents a numerical and experimental study of Love wave propagation in a micro-fabricated phononic crystal (PC) structure consisting of a 2D, periodically etched silica film deposited on a quartz substrate. The dispersion characteristics of Love waves in such a phononic structure were analyzed with various geometric parameters by using complex band structure calculations. For the experiment, we adopted reactive-ion etching with electron-beam lithography to fabricate a submicrometer phononic structure. The measured results exhibited consistency with the numerical prediction. The results of this study may serve as a basis for developing PC-based Love wave devices.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Resonance frequency-retuned quartz tuning fork as a force sensor for noncontact atomic force microscopy

Based on a two-prong type quartz tuning fork, a force sensor with a high Q factor, which we call a retuned fork sensor, was developed for non-contact atomic force microscopy (nc-AFM) with atomic resolution. By cutting a small notch and attaching an AFM tip to one prong, its resonance frequency can be retuned to that of the other intact prong. In balancing the two prongs in this manner, a high Q factor (>50 000 in ultrahigh vacuum) is obtained for the sensor. An atomic resolution image of the Si(111)-7 × 7 surface was demonstrated using an nc-AFM with the sensor. The dependence of the Q factor on resonance frequency of the sensor and the long-range force between tip and sample were measured and analyzed in view of the various dissipation channels. Dissipation in the signal detection circuit turned out to be mainly limited by the total Q factor of the nc-AFM system.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Photo-thermal quartz tuning fork excitation for dynamic mode atomic force microscope

A photo-thermal excitation of a Quartz Tuning Fork (QTF) for topographic studies is introduced. The non-invasive photo-thermal excitation presents practical advantages compared to QTF mechanical and electrical excitations, including the absence of the anti-resonance and its associated phase rotation. Comparison between our theoretical model and experiments validate that the optical transduction mechanism is a photo-thermal rather than photo-thermoacoustic phenomenon. Topographic maps in the context of near-field microscopy distance control have been achieved to demonstrate the performance of the system.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Structural and phase transformation of apatite and quartz in the indentation process single crystals

Using the method of scanning and high-resolution electron microscopy, the zones of indentation by scratching for apatite and quartz single crystals were investigated. The textural, structural and phase transformations revealed have been conventionally ascribed to “deformation” and “diffusion” processes of plastic deformation. In zones of indentation by scratching of single crystals there have been two levels of structural transformations revealed, with a sharp boundary between them, at a stress equal to the theoretical ultimate stress limit (σ{sub TSL}). In the top zone of scratches, within the range of stress from the microhardness value H{sub s} up to the σ{sub TSL} value the substance undergoes profound structural and phase transformations. In the bed of scratches at the stress value lower than σ{sub TSL} values, single crystal fragmentation occurs with the formation of blocks and steps.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗