Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PYRITE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
DOE OSTI2016

In situ Fe-sulfide coating for arsenic removal under reducing conditions

An in situ Fe-sulfide coating approach has been developed for As-contaminated groundwater remediation. Alternate injection of Fe(II), O 2 -free water and S 2$-$ can realize Fe-sulfide coating onto quartz sands with minor changes in porosity. As(III) uptake experiment indicated that the retardation factor for As(III) was 37 and dynamic retention capacity was 44.94 mg As(III)/g Fe, which was much higher than the maximum adsorption capacity for As(III) by FeS and FeS 2 . This result indicated that adsorption cannot be the only mechanism for As(III) uptake by Fe-sulfide coating layer. The SEM image and FTIR spectra results suggested that interaction between As(III) and Fe-sulfides and formation of As-sulfide precipitates could significantly contribute to As(III) uptake by Fe-sulfide coating layer. Alternate injection of Fe(II) + As(III) and S 2$-$ was conducted to simulate in situ As immobilization from real groundwater. The SEM image showed that the quartz sands were mainly covered by crystalline framboidal pyrite after such amendment. The breakthrough of As(III) was not observed during this experiment and the removal capacity for As(III) was 109.7 mg As/g Fe. The As(III) immobilization mechanism during alternate injection of Fe(II) + As(III) and S 2$-$ was significantly different from that of As(III) uptake by Fe-sulfide coating. The direct interaction between As(III) and S 2$-$ produced As-sulfides contributed to the high As(III) removal capacity during alternate injection of Fe(II) + As(III) and S 2$-$ . This result indicated that alternate injection of Fe(II) and S 2$-$ approach has an attractive application for As-contaminated groundwater remediation under strongly reducing environment.

Arsenic contamination↗
DOE OSTI2018

Fe-saponite growth on low-carbon and stainless steel in hydrothermal-bentonite experiments

Hydrothermal experiments on engineered barrier system (EBS) materials were conducted to characterize high temperature interactions between bentonite and candidate waste container steels (304SS, 316SS, low-C steel) for deep geological disposition of nuclear spent fuel. In this study, hydrothermal experiments were performed using Dickson reaction cells at temperatures and pressure of up to 300 °C and 15–16 MPa, respectively, for four to six weeks. Wyoming bentonite was saturated with a 1900 ppm K-Ca-Na-Cl solution in combination with stainless and low-C steel coupons. Authigenic Fe-saponite precipitated utilizing steel as a growth substrate with Fe being supplied by steel corrosion. Concurrent with Fe-saponite formation, sulfides precipitated from sulfide-bearing fluids, from pyrite dissolution, near the steel interface. Sulfide mineral formation is dependent on the steel substrate composition: stainless steel produced pentlandite ((Ni, Fe) 9 S 8 ) and millerite (NiS), whereas low C steel generated pyrrhotite (Fe 7 S 8 ). The presence of sulfides suggests highly reduced environments at the steel-clay barrier interface potentially influencing overall steel corrosion rates and (re)passivation mechanisms. Finally, results of this research show that nuclear waste steel container material may act as a substrate for mineral growth in response to corrosion during hydrothermal interactions with bentonite barriers.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2014

Molecular Dynamics Simulation and Analysis of Interfacial Water at Selected Sulfide Mineral Surfaces under Anaerobic Conditions

In this paper, we report on a molecular dynamics simulation (MDS) study of the behavior of interfacial water at selected sulfide mineral surfaces under anaerobic conditions. The study revealed the interfacial water structure and wetting characteristics of the pyrite (100) surface, galena (100) surface, chalcopyrite (012) surface, sphalerite (110) surface, and molybdenite surfaces (i.e., the face, armchair-edge, and zigzag-edge surfaces), including simulated contact angles, relative number density profiles, water dipole orientations, hydrogen-bonding, and residence times. For force fields of the metal and sulfur atoms in selected sulfide minerals used in the MDS, we used the universal force field (UFF) and another set of force fields optimized by quantum chemical calculations for interactions with interfacial water molecules at selected sulfide mineral surfaces. Simulation results for the structural and dynamic properties of interfacial water molecules indicate the natural hydrophobic character for the selected sulfide mineral surfaces under anaerobic conditions as well as the relatively weak hydrophobicity for the sphalerite (110) surface and two molybdenite edge surfaces. Part of the financial support for this study was provided by the U.S. Department of Energy (DOE) under Basic Science Grant No. DE-FG-03-93ER14315. The Division of Chemical Sciences, Geosciences, and Biosciences, Office of Basic Energy Sciences (BES), of the DOE, funded work performed by Liem X. Dang. Battelle operates Pacific Northwest National Laboratory for DOE. The calculations were carried out using computer resources provided by BES. The authors are grateful to Professor Tsun-Mei Chang for valuable discussions.

Jin, Jiaqi↗
DOE OSTI2017

Iron speciation in peats: Chemical and spectroscopic evidence for the co-occurrence of ferric and ferrous iron in organic complexes and mineral precipitates

The speciation of iron (Fe) in organic matter (OM)-rich environments under in situ variable redox conditions is largely unresolved. Peatlands provide a natural setting to study Fe–OM interactions. Utilizing chemical, spectroscopic and theoretical modeling approaches, we report the chemical forms, oxidation states and local coordination environment of naturally occurring Fe in the vertically redox-stratified Manning peatlands of western New York. In addition, we report dominant carbon, sulfur and nitrogen species that can potentially stabilize the various Fe species present in these peatlands. Our results provide clear direct and indirect evidence for the co-occurrence of ferrous (Fe 2+ ) and ferric (Fe 3+ ) iron species in peats under both oxic and anoxic conditions. Iron is mostly present within the operationally defined organic and amorphous (i.e., short range ordered, SRO) fractions; ferric iron primarily as magnetically isolated paramagnetic Fe 3+ in Fe(III)-organic complexes, but also in mineral forms such as ferrihydrite; ferrous iron in tetrahedral coordination in Fe(II)-organic complexes with minor contribution from pyrite. All of the Fe species identified stabilize Fe(III) and/or Fe(II) in anoxic and oxic peats. Fundamental differences are also observed in the relative proportion of C, S and N functionalities of OM in oxic and anoxic peats. Aromatic C=C, ester, phenol and anomeric C (R-O-C-O-R), as well as thiol, sulfide and heterocyclic N functionalities are more prevalent in anoxic peats. Collectively, our experimental evidence suggests iron forms coordination complexes with O-, S- and N-containing functional groups of OM. We posit the co-occurrence of organic and mineral forms of Fe(II) and Fe(III) in both oxic and anoxic peat layers results from dynamic complexation and hydrolysis-precipitation reactions that occur under variable redox conditions. In conclusion, our findings aid in understanding the crucial role OM plays in determining Fe species in soils and sediments.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2017

Understanding controls on redox processes in floodplain sediments of the Upper Colorado River Basin

Floodplains, heavily used for water supplies, housing, agriculture, mining, and industry, are important repositories of organic carbon, nutrients, and metal contaminants. The accumulation and release of these species is often mediated by redox processes. By understanding the physicochemical, hydrological, and biogeochemical controls on the distribution and variability of sediment redox conditions we can develop conceptual and numerical models of contaminant transport within floodplains. The Upper Colorado River Basin (UCRB) is impacted by former uranium and vanadium ore processing, resulting in contamination by V, Cr, Mn, As, Se, Mo and U. Previous authors have suggested that sediment redox activity occurring within organic carbon-enriched bodies located below the groundwater level may be regionally important to the maintenance and release of contaminant inventories, particularly uranium. To help assess this hypothesis, vertical distributions of Fe and S redox states and sulfide mineralogy were assessed in sediment cores from three floodplain sites spanning a 250 km transect of the central UCRB. Our results support the hypothesis that organic-enriched reduced sediments are important zones of biogeochemical activity within UCRB floodplains. Furthermore, we found that the presence of organic carbon, together with pore saturation, are the key requirements for maintaining reducing conditions, which were dominated by sulfate-reduction products. Sediment texture was found to be of secondary importance and to moderate the response of the system to external forcing, such as oxidant diffusion. Consequently, fine-grain sediments are relatively resistant to oxidation in comparison to coarser-grained sediments. Exposure to oxidants consumes precipitated sulfides, with a disproportionate loss of mackinawite (FeS) as compared to the more stable pyrite. The accompanying loss of redox buffering capacity creates the potential for release of sequestered radionuclides and metals. Because of their redox reactivity and stores of metals, C, and N, organic-enriched sediments are likely to be important to nutrient and contaminant mobility within UCRB floodplain aquifers.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Aerosol iron speciation and seasonal variation of iron oxidation state over the western Antarctic Peninsula

The iron (Fe) speciation and oxidation state have been considered critical factors affecting Fe solubility in the atmosphere and bioavailability in the surface ocean. In this study, elemental composition and Fe speciation in aerosol samples collected at the Palmer Station in the West Antarctic Peninsula were determined using synchrotron-based X-ray fluorescence (XRF) and X-ray Absorption Near-Edge Structure (XANES) spectroscopy. The elemental composition of coarse-mode (>1 mu m) Fe-containing particles suggests that the region's crustal emission is the primary source of aerosol Fe. The Fe minerals in these aerosol particles were predominantly hematite and biotite, but minor fractions of pyrite and ilmenite were observed as well. The Fe oxidation state showed an evident seasonal variation. Further, the Fe(II) content accounted for 71% of the total Fe in the austral summer, while this fraction dropped to 60% in the austral winter. Multivariate linear models involving meteorological parameters suggested that the wind speed, relative humidity, and solar irradiance were the factors that significantly controlled the percentage of Fe(II) in the austral summer. On the contrary, no relationship was found between these factors and the Fe(II) percentage in the austral winter, suggesting that atmospheric photoreduction and regional dust emission were limited. Moreover, the snow depth was significantly (p < 0.05) correlated with the aerosol Fe concentration, confirming the limiting effect of snow/ice cover on the regional dust emission. Given that the Antarctic Peninsula has experienced rapid warming during recent decades, the ice-free areas in the Antarctic Peninsula may act as potential dust sources.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

Biogeochemical controls on iron speciation and cycling across upland to shoreline gradients in freshwater and estuarine coastal soils (Lake Erie and Chesapeake Bay, United States)

Coastal environments are dynamic interfaces that mediate carbon and nutrient exchanges between terrestrial landscapes and open waters, and understanding the biogeochemical factors controlling these exchanges, particularly iron (Fe) redox transformations, is crucial for predicting coastal ecosystem functions. Here, we investigated the mechanisms controlling Fe speciation changes across upland-to-shoreline gradients in freshwater and estuarine soils using Fe K-edge X-ray absorption spectroscopy, solid and porewater composition analysis, and 16S rRNA sequencing analysis. We show that Fe transformations depend primarily on inundation patterns. In unsaturated uplands, Fe occurs as Fe(III) oxyhydroxides, mainly goethite (9–35 %), Fe(II,III)-phyllosilicates (39–89 %), and Fe(III)-organic species (0–61 %). Soils influenced by estuarine waters exhibit porewater sulfide concentrations reaching up to 221 μM, Fe- and S-cycling bacteria, and up to 81 % pyrite (FeS 2 ), indicating that sulfur-driven redox dynamics control Fe transformations. In lacustrine wetlands, Fe(III) reduction is indicated by porewater Fe(II) concentrations increasing to 1.0–2.1 mM, and ~10–15 % of Fe as Fe(II,III)-(hydr)oxides (green rust), vivianite (Fe 3 (PO 4 ) 2 ·8H 2 O), and/or adsorbed Fe(II) species. EXAFS data also indicate reduction of structural Fe(III) to Fe(II) in phyllosilicates. The presence of Fe- and S-cycling bacteria, as well as sulfide (0–10 μM), suggests that Fe-cycling is microbially driven and potentially coupled with cryptic S-cycling. Fe(II) oxidation was indicated above/near the water table by the presence of Fe(III) oxyhydroxides (ferrihydrite, lepidocrocite). Furthermore, negligible Fe(III) or sulfate reduction was observed at some water-saturated sites located at the upland-wetland transition, likely due to oxic (sub-)surface water inputs. Overall, our results highlight the importance of considering both Fe-speciation and hydro-biogeochemical dynamics when predicting Fe-cycling at coastal interfaces.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2016

Monitoring of CoS 2 reactions using high-temperature XRD coupled with gas chromatography (GC)

High-temperature X-ray diffraction with concurrent gas chromatography (GC) was used to study cobalt disulfide cathode pellets disassembled from thermal batteries. When CoS 2 cathode materials were analyzed in an air environment, oxidation of the K(Br, Cl) salt phase in the cathode led to the formation of K 2 SO 4 that subsequently reacted with the pyrite-type CoS 2 phase leading to cathode decomposition between ~260 and 450 °C. Here, independent thermal analysis experiments, i.e. simultaneous thermogravimetric analysis/differential scanning calorimetry/mass spectrometry (MS), augmented the diffraction results and support the overall picture of CoS 2 decomposition. Both gas analysis measurements (i.e. GC and MS) from the independent experiments confirmed the formation of SO 2 off-gas species during breakdown of the CoS 2 . In contrast, characterization of the same cathode material under inert conditions showed the presence of CoS 2 throughout the entire temperature range of analysis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Impact of Acid–Base Stimulation Sequence on Mineral Stability for Tight/Impermeable Unconventional Carbonate-Rich Rocks: A Delaware Basin Case Study

We report mineral precipitation due to reactions with injected fluids during unconventional fracture stimulation is a well-recognized problem. The goal of this study is to evaluate secondary mineral precipitation and permeability attenuation under chemical injection scenarios specific to the Delaware basin. Whole cylindrical cores (2.54 cm diameter and 2.54 cm height) and ground shale (150–250 μm) from the carbonate-rich Bone Spring Formation, Delaware Basin TX (Leonardian), were reacted at 80 °C and 85 bar using a hydraulic fracturing fluid (HFF) recipe and an injection sequence typical of the Delaware Basin. The reacted shales and solutions were analyzed using a variety of laboratory- and synchrotron-based techniques to characterize both the chemical and spatial distributions of secondary mineral precipitation and identify changes in permeability and mineralogy. This carbonate-rich shale (>84% calcite) rapidly neutralized the acidic HFF. Synchrotron-based X-ray fluorescence mapping coupled with X-ray absorption spectroscopy (both bulk and micro) showed that most of the iron was in an oxidized form prior to exposure to HFF and that almost all iron(II) became fully oxidized after the reaction. Scanning electron microscopy images of the ground shale samples primarily identified iron(oxyhydr)oxide microcrystals on grain surfaces. A few small isolated iron-rich areas also contained sulfur, suggesting that some pyrite was preserved when isolated within a calcite crystal but that most was oxidized. The rapid neutralization of the acid spearhead in these carbonate-rich samples demonstrates that the acid spearhead is useful for initiating fractures in extremely calcite-rich rocks but does little to enhance rock permeability. This suggests that the impact of the acid spearhead is significantly smaller for carbonate-rich shales compared to clay-rich shales, which has broad implications for acidizing in carbonate-rich shale formations and iron transformations within these shales.

58 GEOSCIENCES↗
DOE OSTI2022

Experimental Investigation of Barium Sources and Fluid–Rock Interaction in Unconventional Marcellus Shale Wells Using Ba Isotopes

Produced waters from unconventional Marcellus Shale gas wells have anomalously high barium (Ba) concentrations and yield some of the isotopically heaviest Ba measured to date. Experiments were conducted to constrain the source of Ba in these fluids and the controls on barite (BaSO 4 ) precipitation and dissolution in oil and gas wells. Experiments simulating the acidizing stage evaluated the solubility of pure barite and drilling mud in 2 M HCl at 80 °C for periods of 2, 6, and 48 h and resulted in <0.01% barite dissolution with no appreciable change in δ 138 Ba ( 138 Ba/ 134 Ba normalized to NIST standard 3104a). Static autoclave experiments conducted at 66 °C and 20.7 MPa with combinations of ground Marcellus Shale solids and/or barite-bearing drilling mud with synthetic low-Ba fracturing fluid resulted in decreased Ba concentrations in the fluid, with the largest decrease in the shale-only run. Fluid δ 138 Ba values increased by about 0.5‰ as Ba concentrations decreased, consistent with closed-system Rayleigh fractionation. Flow-through experiments in Marcellus Shale core conducted for 28 days resulted in effluent Ba concentrations an order of magnitude lower than the influent, while sulfate concentrations increased over time. Effluent δ 138 Ba values increased over the first 12 days and plateaued at about 1‰ higher than the influent. Modeling suggests a combination of the release of labile shale Ba and barite precipitation. This work indicates that the processes of Ba release from fluid–shale interactions and barite precipitation in fractures and the well bore, while capable of producing high δ 138 Ba fluids, are unlikely to generate fluids with high-Ba concentrations and δ 138 Ba values like those in Marcellus-produced waters. As a result, we find that the release of sulfate from shale pyrite oxidation rapidly catalyzes barite precipitation and that dissolution of drilling mud barite or natural barite in the shale is unlikely to be the major source of Ba in Marcellus-produced waters.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Impact of Concurrent Solubilization and Fines Migration on Fracture Aperture Growth in Shales during Acidized Brine Injection

Acidic hydraulic fracturing fluid chemically and physically alters shale rock fabric during injection and shut-in, creating a “reaction-altered zone” along the fracture faces. To better characterize the variable thickness and composition of this reaction-altered zone under advective flow, we take a coupled experimental and modeling approach. A fluidic cell, with six fiducial markers, is first fabricated to keep the rock sample in place during the core floods and to allow image alignment of acquired images. Then, we conduct a series of reactive core floods in a clay-rich siliceous Wolfcamp shale sample with 10 wt % carbonate, using a synthetic fracturing fluid under no confining stress and at room temperature. High-resolution computed tomography (CT) scans are periodically conducted to observe the spatial alteration of the fracture network. We then perform scanning electron microscopy (SEM-EDS) on the two orthogonal surfaces (fracture surface and freshly cut profile face) to generate high-resolution elemental maps that show the change in mineralogy, both with distance along a given flow path along a fracture surface and with depth from the fracture surface into the shale matrix. These results are contrasted against a two-dimensional (2D) advection-diffusion reaction model developed previously for batch reactions between shale and synthetic fracturing fluids. The model simulates the geochemical interaction occurring at the fracture/matrix interface and penetrating into the shale matrix during the reactive core flood. Both model and experimental results show that the acidic brine is neutralized during the core flood, corresponding to an increase in fracture aperture as a function of fluid volume injected with the greatest change near the inlet. SEM-EDS scans reveal significant dissolution of carbonates on the fracture surface without pyrite oxidation. The reactive transport model indicates that carbonate depletion into the shale interior should be observable, yet SEM-EDS shows no discernible loss of carbonate in the orthogonal profile face. The combination of these observations suggests an additional fracture evolution mechanism in the reactive system, i.e., fines migration. We show that fines migration enhances the access of fracturing fluid to the matrix resulting in a more pronounced fracture widening. Finally, we conclude that coupled mineral dissolution and fines migration govern fracture aperture growth during acidized brine injection. In this work, we effectively show the underlying risk of relying solely on models that do not include an important (transport) process that can alter the system significantly and propose a combined chemomechanical mechanism for fracture evolution appropriate for this shale mineralogy.

58 GEOSCIENCES↗
DOE OSTI2022

Integrated Experimental and Modeling Study of Geochemical Reactions of Simple Fracturing Fluids with Caney Shale

Interactions between rock minerals and hydraulic fluids directly impact the geochemical and geomechanical properties of shale formations. However, the mechanisms of geochemical reactions in shale unconventional reservoirs remain poorly understood. Here, to investigate the geochemical reactions between shale and hydraulic fracturing fluids, a series of batch reactor experiments were undertaken. Three rock samples with different mineralogical compositions and three fluid samples of different compositions (deionized water, deionized water + 2% potassium chloride (KCl), and deionized water + 0.5% choline chloride (C 5 H 14 ClNO) were used. Experiments were undertaken at reservoir temperature and atmospheric pressure. Elemental compositions of effluents after 1, 3, 7, 14, 28 days were analyzed using Inductively Couple Plasma Mass Spectrometry (ICP-MS). Medical Computed Tomography (CT) scan and X-ray Fluorescence (XRF) were conducted on the entire core run to help upscale results obtained from rock-fluid interaction experiments. Geochemical modeling using a reactive simulator, TOUGHREACT, was undertaken to corroborate experimental results. Results show that lower pH triggered high dissolution rates in the rock samples, especially the carbonate components. As pH increased, the rate of dissolution declined significantly, though for most cases dissolution still continued. Observed dissolved silica concentrations were much higher than the quartz solubility, suggesting that much of the silica originates from more soluble silica polymorphs and possibly desorption from clay mineral exchange sites. Concentration of most elemental species in solution increased but aluminium and magnesium concentrations declined rapidly following initial entry into solution. Geochemical modeling corroborated the conclusions regarding mineral dissolution and precipitation observed from experiments, notably; the dissolution of calcite and oxidation of pyrite in reacted shale samples, the likely presence of silica polymorphs such as opal, chalcedony or amorphous silica in these samples, and the reduction of Al and Mg concentrations in solution by precipitation of secondary aluminosilicate phases. The de-flocculation of clay minerals during reaction implies fines migration after hydraulic fracturing. This is detrimental to reservoir productivity as clay fines are displaces and lodged within the micro and nano-fractures created during fracturing. The immediate consumption of aluminium and magnesium also has implications on blockage of hydrocarbon pathways due to precipitation of new minerals in these locations.

04 OIL SHALES AND TAR SANDS↗
DOE OSTI2025

Inorganic Alterations in Unconventional Shale Reservoirs: Importance of Additive and Base Fluid Chemistry

The effective development of unconventional petroleum systems requires the use of significant water resources. In an effort to reduce the consumption of freshwater resources for hydraulic fracturing, highly saline produced waters are increasingly recycled for use as a base fluid. However, there are significant knowledge gaps regarding potential water–rock interactions resulting from the introduction of produced waters and associated additives into shale reservoirs such as formation and deposition of mineral scale, which can negatively affect hydrocarbon production through wellbore restriction and damage to hydraulically generated fractures. To assess the impacts of field stimulation practices in the subsurface, a series of laboratory experiments were completed using (a) three distinct sedimentary rock formations of the Midland Basin (Texas, USA) and (b) additives with two different base fluids: municipal fresh water and clean brine. The experimental approach used relevant injection sequences and mixing ratios in specialized reactors for 3 weeks. Static pressurized experiments and nonpressurized time-resolved experiments were undertaken. The resulting solids and liquids were analyzed by using a variety of laboratory- and synchrotron-based techniques. The use of an acid spearhead (15% HCl) resulted in texturing of both clay-rich and calcareous shales, which can temporarily enhance porosity but subsequently result in mineral scale deposition. The primary matrix scale was Fe(III)-bearing phases, which occurred in all experiments regardless of base fluid chemistry. Additionally, strontium sulfate (SrSO 4 ) precipitated on shale surfaces when clean brines were used. It was concluded that clean brine was the main source of Sr 2+ species, while persulfate breaker degradation and oxidation of pyrite were the sources of SO 4 2– . Sulfate scaling was more pronounced in clay-rich shales, suggesting that Sr sorption is important for promoting celestite formation. This work demonstrates that mineral scale deposition is a complex phenomenon, whereby the type and proportions of various mineral phases are determined from reservoir alteration processes and coprecipitation of constituents from injection fluids. In conclusion, the experimental results shown here should be considered when evaluating different base fluids and additives in order to mitigate mineral precipitation in unconventional shale reservoirs, which could result in reservoir degradation.

Jew, Adam D. [SLAC National Accelerator Laboratory↗
DOE OSTI2017

Impact of organics and carbonates on the oxidation and precipitation of iron during hydraulic fracturing of shale

Hydraulic fracturing of unconventional hydrocarbon reservoirs is critical to the United States energy portfolio; however, hydrocarbon production from newly fractured wells generally declines rapidly over the initial months of production. One possible reason for this decrease, especially over time scales of several months, is the mineralization and clogging of microfracture networks and pores proximal to propped fractures. One important but relatively unexplored class of reactions that could contribute to these problems is oxidation of Fe(II) derived from Fe(II)-bearing phases (primarily pyrite, siderite, and Fe(II) bound directly to organic matter) by the oxic fracture fluid and subsequent precipitation of Fe(III)-(oxy)hydroxides. Here, the extent to which such reactions occur and their rates, mineral products, and physical locations within shale pore spaces are unknown.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Reactive Transport Modeling of Shale–Fluid Interactions after Imbibition of Fracturing Fluids

Injection of hydraulic fracturing fluid (HFF) into shale formations for unconventional oil/gas production results in chemical reactions in the shale matrix. Our recent experimental study determined the depths to which different types of reactions between the shale matrix and the HFF extended. In the present study, we built continuum-scale reactive transport models to understand the coupling of chemical reactions and the transport of aqueous species in these shale–HFF systems. Calibration of the model with our previous experimental results reveals that it takes hours to months for the shale matrix to completely neutralize the imbibed acids, depending primarily upon the carbonate content of the shale. Both the HFF pH and pore pH affect the location of barite precipitation, resulting in unique barite precipitation profiles extending millimeters into calcite-rich Eagle Ford shale but only tens of micrometers into low-carbonate Marcellus shale. In addition, dissolved oxygen and extracted bitumen are key to reproducing the experimental observation of Fe(III) (oxyhydr)oxide formation in the shale matrix as a result of pyrite dissolution in the shales. A comparison between the modeling results of porosity in the present study to experimentally measured permeabilities in our previous study suggests that chemical reactions occurring at a greater depth than the observable reaction zone might have impacted permeability. Our model serves as a benchmark for efficiently modeling water–rock interactions in similar systems where bulk rock samples react with a solution in batch reactors. Important reactive transport processes were ascertained via modeling, which allows for quantitative prediction of shale–HFF interactions in shale matrices given the shale and HFF compositions.

58 GEOSCIENCES↗
DOE OSTI2022

Giant Thermoelectric Power Factor Anisotropy in PtSb 1.4 Sn 0.6

In this work, we report on the giant anisotropy found in the thermoelectric power factor (S 2 σ) of marcasite structure-type PtSb 1.4 Sn 0.6 single crystal. PtSb 1.4 Sn 0.6 , synthesized using an ambient pressure flux growth method upon mixing Sb and Sn on the same atomic site, is a new phase different from both PtSb 2 and PtSn 2 , which crystallize in the cubic Pa$\bar{3}$ pyrite and Fm$\bar{3}$m fluorite unit cell symmetry, respectively. The large difference in S 2 σ for heat flow applied along different principal directions of the orthorhombic unit cell stems mostly from anisotropic Seebeck coefficients.

36 MATERIALS SCIENCE↗