Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PRESSES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

Investigation of specimen size effects by in-situ microcompression of equal channel angular pressed copper

Here, micropillar compression testing was implemented on Equal Channel Angular Pressed copper samples ranging from 200 nm to 10 µm in side length in order to measure the mechanical properties yield strength, first load drop during plastic deformation at which there was a subsequent stress decrease with increasing strain, work hardening, and strain hardening exponent. Several micropillars containing multiple grains were investigated in a 200 nm grain sample. The effective pillar diameter to grain size ratios, D/d , were measured to be between 1.9 and 27.2. Specimens having D/d ratios between 0.2 and 5 were investigated in a second sample that was annealed at 200 °C for 2 h with an average grain size of 1.3 µm. No yield strength or elastic modulus size effects were observed in specimens in the 200 nm grain size sample. However work hardening increases with a decrease in critical ratios and first stress drops occur at much lower stresses for specimens with D/d ratios less than 5. For comparison, bulk tensile testing of both samples was performed, and the yield strength values of all micropillar compression tests for the 200 nm grained sample are in good agreement with the yield strength values of the tensile tests.

36 MATERIALS SCIENCE↗

Micro X-ray computed tomography examination of mini plate fuel with hot isostatic pressed aluminum cladding

In order to minimize proliferation risks and improve security of nuclear material, the United States high performance research and test reactors (USHPRR) program is tasked with converting nuclear reactors that are fueled with highly enriched uranium (HEU) fuels to operate with low-enriched uranium (LEU) nuclear fuels. One favorable LEU fuel configuration is plate fuel with a metallic uranium-molybdenum foil clad within an aluminum alloy (AA 6061). In this fuel, the aluminum cladding is bonded with a hot isostatic pressing (HIP) method to seal the cladding around the fuel meat. However, the HIP process parameters influence the cladding performance, as a defective or incomplete bond can cause a pathway for corrosion. Micro X-ray computed tomography (XCT), a nondestructive technique that provides volumetric imaging, can be applied to inspect fuel plate cladding at the engineering scale. In this work, XCT methodology was developed and successfully utilized to not only observe the bond line of unirradiated mini fuel plates, but to also identify subsurface abnormalities in the plates’ cladding. Importantly, in future work, this technique could be applied to fuel plates, pre- and post-irradiation, to quantify irradiation effects on cladding defects and bond line integrity.

36 MATERIALS SCIENCE↗

Hot-pressed 6 LiInSe 2 for use as a ceramic radiation detector

Lithium based chalcogenides have many uses in the nuclear science field. 6 LiInSe 2 (or LISe) has been researched extensively because of its ability to operate in both scintillator and semiconductor modes. Here, this makes it useful in applications including nuclear material detection for national security, space applications, and medical imaging. In some applications growth and fabrication costs are of concern, as it takes upwards of 40 days to synthesize a charge, grow a crystal and fabricate a detector. Ceramics are a solution for this long route of preparation. This research shows that using a 6 LiInSe 2 ceramic instead of a single crystal significantly decreases the time required to make a detector. In the present work, ceramic wafers can be formed using a mechanical press equipped with a heating attachment. The resulting ceramic wafer performs very similar to a slow-growth single crystal when used in the scintillator mode.

36 MATERIALS SCIENCE↗

Theoretical and experimental investigation of matrix effects observed in emission spectra of binary mixtures of sodium and copper and magnesium and copper pressed powders

Here, the goal of this work was to investigate the matrix effect of copper in the presence of sodium or magnesium in a laser-induced plasma. Varying amounts of copper were mixed and pressed with a constant amount of sodium or magnesium and a stearic acid binder. Experimental parameters such as delay time and laser pulse energy were varied to observe trends in the emission intensity of the Na I 588.99 nm, Na I 589.59 nm, Mg I 277.98 nm, and Mg II 279.08 nm lines. Experimental observations are supported by theoretical calculations and modeling that show the Na I and Mg I emission intensities increase in the presence of copper while the Mg II line intensity decreases due to the increase in electron density (Ne) of the plasma when copper is added. Lastly, the increase in electron density changes the population of the atomic species within the plasma through an increase in recombination of ions with electrons, shifting the populations toward more neutral states, providing an explanation for the observed matrix effects found in these, and many previous, studies.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

One dimensional shock initiation of hot isostatically pressed composition B

Twelve one dimensional shock experiments have been carried out on the UK isostatically pressed Composition B (59.5% RDX, 39.5% TNT, 1% wax) comprising of seven sustained pulse experiments and three short shock experiments using the embedded gauge technique at the Los Alamos National Laboratory gas gun facility. The evolution of the reactive growth at and behind the shock front has been measured along with the run to detonation distance. Two low pressure experiments have also been carried out to obtain non-reactive equation of state data. These data have been used to create the Pop plot and Hugoniot states for the UK Comp B. The shock initiation behavior of the UK Comp B has been compared to that of the equivalent US composition. The reactive growth shows a feature that was observed in the US composition in which the wave profiles display a high level of pre-detonation noise. This was hypothesized to be due to a piezoelectric effect in the RDX crystals. The results of these experiments have shown that this effect may be localized in the ε phase at shock pressures in the region of 4.15 GPa and above.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Shock to detonation transition of pentaerythritol tetranitrate (PETN) initially pressed to 1.65 g/cm 3

A novel set of experiments and reactive flow modeling of pentaerythritol tetranitrate (PETN) is presented. In this work, the specific phenomenon of shock to detonation transition is examined, where an initial, relatively weak shock is propagated into pressed PETN powder at 1.65 g/cm 3 and the subsequent buildup to detonation is observed experimentally. These experiments, in conjunction with reactant and products’ equations of state, are utilized for building reactive flow models.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Vented and sealed cookoff of powdered and pressed ε-CL-20

In this work, we have completed a series of vented and sealed cookoff experiments of the ε-polymorph of CL-20 in our Sandia Instrumented Thermal Ignition (SITI) apparatus using both powder and pressed pellets at nominal densities of 313 ± 8 kg/m 3 and 1030 ± 4 kg/m 3 , respectively. The boundary temperature of our aluminum confinement cylinder was ramped in 10 minutes from room temperature to a prescribed set-point temperature ranging between 448 nd 468 K and held at the set-point temperature until ignition. A universal cookoff model (UCM) has been calibrated using the ε-CL-20 SITI data to predict pressurization and thermal ignition of ε-CL-20. The ignition model was validated by using one-dimensional time-to-explosion (ODTX) ignition data from a different laboratory. We found that a thirtyfold increase in the reaction rates due to liquefaction at 520 K could explain the high temperature ODTX cookoff data. The model gives a plausible explanation of why melting is important in fast cookoff events involving CL-20. Our model also gives support to 520 K as the liquefaction point of CL-20, which has different values in the literature.

36 MATERIALS SCIENCE↗

Evolution of domain wall networks: The Press-Ryden-Spergel algorithm

The Press-Ryden-Spergel (PRS) algorithm is a modification to the field theory equations of motion, parametrized by two parameters ({alpha} and {beta}), implemented in numerical simulations of cosmological domain wall networks, in order to ensure a fixed comoving resolution. In this paper we explicitly demonstrate that the PRS algorithm provides the correct domain wall dynamics in (N+1)-dimensional Friedmann-Robertson-Walker universes if {alpha}+{beta}/2=N, fully validating its use in numerical studies of cosmic domain evolution. We further show that this result is valid for generic thin featureless domain walls, independently of the Lagrangian of the model.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

The Press and Pulse of Climate Change: Extreme Events in the Colorado River Basin

Extremes in temperature and precipitation are associated with damaging floods, prolonged drought, destructive wildfires, agricultural challenges, compromised human health, vulnerable infrastructure, and threatened ecosystems and species. Often, the steady and progressive trends (or presses) of rising global temperature are the central focus in how climate impacts are described. However, observations of extreme weather events (or pulses) increasingly show that the intensity, duration and/or frequency of acute events are also changing, resulting in greater impacts on communities and the environment. Describing how the influence of extreme events may shape water management in the Colorado River Basin in clear terms is critical to sound future planning and efforts to manage risk. Three scenario planning workshops in 2019 and 2020 were held as part of a Colorado River Conversations series, identifying potential impacts from multiple intersecting extreme events. Water managers identified climate-related events of concern in the Colorado River Basin that necessitate greater attention and adaptive responses. To support efforts to include consideration of climate-change-driven extremes in water management and planning, we explore the current state of knowledge at the confluence of long-term climate shifts and extreme weather in the Colorado River Basin related to the events of concern that were identified by scenario planning participants.

54 ENVIRONMENTAL SCIENCES↗

Hertzian Ring Crack Initiation in Hot-Pressed Silicon Carbide

The use of Hertzian indentation to measure ring crack initiation force (RCIF) distributions in four hot-pressed silicon carbide (SiC) ceramics is described. Three diamond indenter diameters were used with each SiC; the RCIF in each test was identified with the aid of an acoustic emission system; and two-parameter Weibull RCIF distributions were determined for all 12 combinations. RCIF testing was found to be an effective discriminator of contact damage initiation and response. It consistently produced the same ranking of RCIF between the four SiCs, with all three different indenter diameters, which is noteworthy because Knoop hardness and fracture toughness measurements were only subtly different or equivalent for the four SiCs. However, because RCIF, like hardness, is a characteristic response of a target material to an applied indentation condition (e.g., a function of indenter diameter) and not a material property, the implications and possible limitations should be acknowledged when using RCIF to discriminate the target material response.

36 MATERIALS SCIENCE↗

Hot-pressed ceramic Fe:ZnSe gain-switched laser

We report the first room temperature gain-switched Fe:ZnSe hot-pressed ceramic laser pumped by 2.94 µm radiation of mechanically Q-switched Er:YAG laser. The maximum output energy at 4.2 µm was 41 mJ at 3 Hz repetition rate and 120 ns pulse duration. The measured slope efficiency was 25% with respect to the absorbed energy. This technique could be attractive for the future development of high-energy short-pulse solid-state mid-IR systems.

36 MATERIALS SCIENCE↗

Hot Isostatic Press Can Optimization for Aluminum Cladding of U-10Mo Reactor Fuel Plates: FY12 Final Report and FY13 Update

Currently, the proposed processing path for low enriched uranium – 10 wt. pct. molybdenum alloy (LEU-10Mo) monolithic fuel plates for high power research and test reactors includes hot isostatic pressing (HIP) to bond the aluminum cladding that encapsulates the fuel foil. Initial HIP experiments were performed at Idaho National Laboratory (INL) on approximately ¼ scale “mini” fuel plate samples using a HIP can design intended for these smaller experimental trials. These experiments showed that, with the addition of a co-rolled zirconium diffusion barrier on the LEU-10Mo alloy fuel foil, the HIP bonding process is a viable method for producing monolithic fuel plates. Further experimental trials at Los Alamos National Laboratory (LANL) effectively scaled-up the “mini” can design to produce full-size fuel prototypic plates. This report summarizes current efforts at LANL to produce a HIP can design that is further optimized for higher volume production runs. The production-optimized HIP can design goals were determined by LANL and Babcock & Wilcox (B&W) to include maintaining or improving the quality of the fuel plates produced with the baseline scaled-up mini can design, while minimizing material usage, improving dimensional stability, easing assembly and disassembly, eliminating machining, and significantly reducing welding. The initial small-scale experiments described in this report show that a formed-can approach can achieve the goals described above. Future work includes scaling the formed-can approach to full-size fuel plates, and current progress toward this goal is also summarized here.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Coefficient of Thermal Expansion of Pressed PETN Pellets

The PETN single crystal coefficient of thermal expansion (CTE) values were measured and reported by Cady in 1972 [1] over the temperature range of -160 to 100°C. Measurements were made in the (001) and (100) crystallographic directions, see Figure 1 (a replicate of Figure 1 from the Cady paper). Cady used his single-crystal data to calculate the linear CTE for a randomly-oriented multi-crystal pressing of PETN, and his values ranged from 76.5 με/°C (at 20°C) to 89.9 5 με/°C (at 90°C).

36 MATERIALS SCIENCE↗

The mechanics of pressed-pellet separators in molten salt batteries

We present a phenomenological constitutive model that describes the macroscopic behavior of pressed-pellet materials used in molten salt batteries. Such materials include separators, cathodes, and anodes. The purpose of this model is to describe the inelastic deformation associated with the melting of a key constituent, the electrolyte. At room temperature, all constituents of these materials are solid and do not transport cations so that the battery is inert. As the battery is heated, the electrolyte, a constituent typically present in the separator and cathode, melts and conducts charge by flowing through the solid skeletons of the anode, cathode, and separator. The electrochemical circuit is closed in this hot state of the battery. The focus of this report is on the thermal-mechanical behavior of the separator, which typically exhibits the most deformation of the three pellets during the process of activating a molten salt battery. Separator materials are composed of a compressed mixture of a powdered electrolyte, an inert binder phase, and void space. When the electrolyte melts, macroscopically one observes both a change in volume and shape of the separator that depends on the applied boundary conditions during the melt transition. Although porous flow plays a critical role in the battery mechanics and electrochemistry, the focus of this report is on separator behavior under flow-free conditions in which the total mass of electrolyte is static within the pellet. Specific poromechanics effects such as capillary pressure, pressure-saturation, and electrolyte transport between layers are not considered. Instead, a phenomenological model is presented to describe all such behaviors including the melting transition of the electrolyte, loss of void space, and isochoric plasticity associated with the binder phase rearrangement. The model is appropriate for use finite element analysis under finite deformation and finite temperature change conditions. The model reasonably describes the stress dependent volume and shape change associated with dead load compression and spring-type boundary conditions; the latter is relevant in molten salt batteries. Future work will transition the model towards describing the solid skeleton of the separator in the traditional poromechanics context.

25 ENERGY STORAGE↗

Hot Isostatic Pressing of Engineered Forms of I-AgZ

Hot isostatic pressing (HIP) is being considered for direct conversion of 129 I-bearing materials to a radiological waste form. The removal of volatile radioactive 129 I from the off-gas of a nuclear fuel reprocessing facility will be necessary to comply with regulatory requirements regarding reprocessing facilities sited within the United States, and any iodine-containing media or solid sorbents generated by offgas abatement will require disposal. Zeolite minerals such as silver-exchanged mordenite (AgZ) have been studied as potential iodine sorbents and will contain 129 I as chemisorbed AgI. Oak Ridge National Laboratory (ORNL) has conducted several recent studies on the HIP of both iodine-loaded AgZ (I-AgZ) and other iodine-bearing zeolite minerals. The goal of these research efforts is to achieve a stable, highly leach resistant material that is reduced in volume as compared to bulk iodine-loaded I-AgZ. Through the use of HIP, it may be possible to achieve this with the addition of little or no additional materials (waste formers). Other goals for the process include that the waste form will be tolerant to high temperatures and pressures, not chemically hazardous, and that the process will result in minimal secondary waste generation. This document describes the preparation of 27 samples that are distinct from previous efforts in that they are prepared exclusively with an engineered form of AgZ that is manufactured using a binder. Iodine was incorporated solely by chemisorption. This base material is expected to be more representative of an operational system than were samples prepared previously with pure minerals.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Unsupervised Machine Learning for Evaluation of Aging in Explosive Pressed Pellets

This project is an evaluation of the changes in the dimensional geometry of pressed explosive powder pellets when stored for prolonged periods under unmonitored storage conditions. Through the application of Structural Health Monitoring (SHM) techniques, questions to be answered by this investigation are what, if any, effect has the long-term storage of the pellets had on their physical attributes and, if changes have occurred, are the resulting differences of significant magnitude to affect the performance of the pellets. This resulting report includes a summary of the relevant background information, explanation of the SHM approach used to analyze the available data, presentation and discussion of the results, concluding remarks, and an accompanying appendix containing the MATLAB program developed for the project.

36 MATERIALS SCIENCE↗

Pseudo-Hot-Isostatic Pressing (P-HIP)

Researchers at Los Alamos National Laboratory developed a technology to produce high performance ceramic or metal with a combination of major key properties such as versatile-complicated shape, high density, uniform density distribution, and minimal amounts of starting material. The novel pseudo-hot-isostatic-pressing (P-HIP) uses graphite or boron nitride flakes as the stress transmission media to transmit stress instead of the conventional solid graphite punch. The graphite and boron nitride flakes are solid lubricants and can slide among one another to re-distribute the stress from high stress concentration area to the low stress concentration areas, resulting in a self-stress-relief action. This innovative P-HIP enables the manufacturing of complicated shapes with near-net-shape capability while minimizing the energy used and reducing waste. This is a revolutionary breakthrough to the ceramics and powder metallurgy industries.

36 MATERIALS SCIENCE↗