SEARCH · Engineering Papers

Results for “PINS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

All sources NASA NTRS DOE OSTI

NASA NTRS1974

Tool for use in lifting pin supported objects

A tool for use in lifting a pin-supported, electronic package mounted in juxtaposition with the surface of an electronic circuit board is described. The tool is configured to be received beneath a pin-supported package and is characterized by a manually operable linkage, including an elongated, rigid link is supported for axial reciprocation and a pivotal link pinned to the body and supported for oscillation induced in response to axial motion imparted to the rigid link. A lifting plate is pivotally coupled to the distal end of the pivotal link so that oscillatory motion imparted to the pivotal link serves to move the plate vertically for elevating the plate into lifting engagement with the electronic package positioned thereabove.

Marzek, R. A.↗

NASA NTRS1977

Heat-transfer coefficients of pin-finned cylinders

Pin-finned cylinder can increase heat-transfer rate to more than 4 times that of plain cylinder, depending on pin diameter and spacing. Smallest diameter, closest spacing, and largest pin length-to-diameter ratio gives highest average effective heat-transfer coefficients.

Van Fossen, G. J., Jr.↗

NASA NTRS1976

Pin puller impact shock attenuation

Design of a pin arresting mechanism for a pyrotechnically actuated pin puller is reviewed. The investigative approach is discussed and the impact shock test results for various candidate designs are presented. The selected pin arresting design reduced the peak value of the shock response spectrum by five to one.

Auclair, G. F.↗

NASA NTRS1982

Tool Blunts Cotter Pin Legs for Safety

Jaws on new insertion tool contain upset point and anvil. Point forces cotter-pin legs into loop as it engages anvil. Cotter pin before insertion consists of loop and straight shaft composed of two legs welded together as tips. After insertion, welded legs have been shaped into loop. Tool used to prevent bent loose ends of cotter pins from scratching workers' fingers or cutting and entangling wires.

Stein, J. A.↗

NASA NTRS1985

Anvil for Flaring PCB Guide Pins

Spring-loaded anvil results in fewer fractured pins. New anvil for flaring guide pins in printed-circuit boards absorbs approximately 80 percent of press force. As result fewer pins damaged, and work output of flaring press greatly increased.

Winn, E.↗

NASA NTRS1985

Analysis of a finite composite plate with smooth rigid pin

An elastic continuum method of analysis developed for a smooth rigid pin in a finite composite plate by using complex potentials that satisfy the governing orthotropic differential equation is presented. The plate is subjected to uniaxial loading and the nonlinear problems of partial contact in the pin-plate are studied. Three types of pin fits are examined: interference, push, and clearance. The problems of stresses due to pure interference, load contact behavior, and stresses variations are addressed. The effects of the rectangular geometry and the orthotropic property of the plate are demonstrated through numerical results. It is found that the use of large hole diameter/plate width ratios have deleterious effects and the use of interference has beneficial effects. The solutions obtained will help in the development of special finite elements for fastener joints. Finally, the boundary conditions on the finite outer boundaries are found to be satisfied by a successive integration technique.

Naidu, A. C. B.↗

NASA NTRS1986

Measurement of contact angle in a clearance-fit pin-loaded hole

A technique which measures load-contact variation in a clearance-fit, pin-loaded hole is presented in detail. A steel instrumented pin, which activates a make-or-break electrical circuit in the pin-hole contact region, was inserted into one aluminum and one polycarbonate specimen. The resulting load-contact variations are indicated schematically. The ability to accurately determine the arc of contact at any load was crucial to this measurement. It is noted that this simple experimental technique is applicable to both conducting and nonconducting materials.

Prabhakaran, R.↗

NASA NTRS1990

Magnetic properties of high-T(sub c) superconductors: Rigid levitation, flux pinning, thermal depinning, and fluctuation

The levitation of high-T(sub c) superconductors is quite conspicuous: Above magnets of low symmetry a disk of these ceramics floats motionless, without vibration or rotation; it has a continuous range of stable positions and orientations as if it were stuck in sand. Some specimens may even be suspended above or below the same magnet. This fascinating stability, inherent to no other type of levitation, is caused by the pinning of magnetic flux lines by inhomogeneities inside these extreme type-2 superconductors. The talk deals with pinning of magnetic flux in these materials, with flux flow, flux creep, thermally activated depinning, and the thermal fluctuation of the vortex positions in the flux line lattice (often called flux lattice melting). Also discussed are the fluctuations of the (nearly periodic) magnetic field inside these superconductors which are caused by random pinning sites and by the finite temperature. These fluctuations broaden the van-Hove singularities observed in the density of the magnetic field by nuclear magnetic resonance and by muon spin rotation.

Brandt, E. H.↗

NASA NTRS1992

Adjustably Preloaded Quick-Release Pin

Modified adjustable-grip-length quick-release pin holds two bodies together. Threaded shaft of pin threaded in floating nut to pretension fastener. Pin connects and disconnects rapidly and adjusted to accommodate small differences between thicknesses of nominally identical sets of parts to be attached to each other.

Reimers, Harold W.↗

NASA NTRS1992

Pin-Height Gauge

Gauge aligns itself and retains indication for later reading. Measuring tool indicates height of protrusion of pin from flat surface. Tool surrounds pin and holds itself square with flat surface, ensuring proper alignment and accuracy of measurement. Used in hard-to-see and hard-to-reach places. Holds indication of height until read. Metal scale slides in and out through slot in top plate. Scale value at slot gives height of pin under piston. Dimensions in inches.

Sumrall, Daniel R.↗

NASA NTRS1992

Heat transfer in thin, compact heat exchangers with circular, rectangular, or pin-fin flow passages

Heat transfer and pressure drop have been measured of three thin, compact heat exchangers in helium gas at 3.5 MPa and higher, with Reynolds numbers of 450 to 36,000. The flow geometries for the three heat exchanger specimens were: circular tube, rectangular channel, and staggered pin fin with tapered pins. The specimens were heated radiatively at heat fluxes up to 77 W/sq cm. Correlations were developed for the isothermal friction factor as a function of Reynolds number, and for the Nusselt number as a function of Reynolds number and the ratio of wall temperature to fluid temperature. The specimen with the pin fin internal geometry had significantly better heat transfer than the other specimens, but it also had higher pressure drop. For certain conditions of helium flow and heating, the temperature more than doubled from the inlet to the outlet of the specimens, producing large changes in gas velocity, density, viscosity, and thermal conductivity. These changes in properties did not affect the correlations for friction factor and Nusselt number in turbulent flow.

Olson, D. A.↗

NASA NTRS1994

Lever-Arm Pin Puller

Mechanism holds retaining pins in place except when actuated to release pins quickly. Mechanism is integral part of cover designed to be removed with simple downward motion of hand. Before removal, mechanism secures cover in place. After removal, mechanism holds retaining pins for reuse.

Macmartin, Malcolm↗

NASA NTRS1992

X-ray spectroscopy with silicon pin and avalanche photo diodes

Results of an evaluation of silicon P-Intrinsic-N (PIN) photodiodes and Avalanche Photodiodes (APD) for the direct detection of soft x rays from 1 to 20 keV and for the detection of scintillation light output from CsI(TI) for higher x ray energies (30 to 1000 keV) are presented. About one keV resolution was achieved at room temperature for both the PIN and APD detectors for soft x rays (1 to 20 keV). Commercially available, low power (18 mV), low noise, hybrid preamplifiers, were used. These photodiodes were also coupled to CsI(TI) scintillator and obtained about 6 resolution at 662 keV. The photodiode frequency response matches well with the emission spectrum of the CsI(TI) scintillator providing good spectral resolution and a higher signal than NaI(TI) when viewed by conventional photomultipliers. A PIN-CsI(TI) combination provides a low energy threshold of around 60 keV while for the APD-CsI(TI) it is 15 keV.

Desai, U. D.↗

NASA NTRS2001

Evaluation of Forces on the Welding Probe of the Automated Retractable Pin-Tool (RPT)

The NASA invention entitled 'The Hydraulic Controlled Auto-Adjustable Pin Tool for Friction Stir Welding' (US Patent 5,893,507), better known as the Retractable Pin-Tool (RPT), has been instrumented with a load-detecting device allowing the forces placed on the welding probe to be measured. As the welding probe is plunged into the material, the forces placed on the probe can now be characterized. Of particular interest are those forces experienced as the welding probe comes within close proximity to the back-up anvil. For a given material, it is believed that unique forces are generated relative to the distance between the welding probe and the anvil. The forces have been measured and characterized for several materials, and correlations have been made between these forces and the pin's position relative to the backside of the weld material.

Ding, R. J.↗

NASA NTRS1999

Evaluation of Forces on the Welding Probe of the Retractable Pin-Tool (RPT)

NASA invention entitled, "The Hydraulic Controlled Auto-Adjustable Pin Tool for Friction Stir Welding" (U.S. Patent 5,893,5 07), better known as the Retractable Pin-Tool (RPT) has been instrumented with a load detecting devise allowing the forces placed upon the welding probe to be measured. As the welding probe is plunged into the material, the forces placed upon the probe can now be charactefized. Of particular interest are those forces experienced as the welding probe comes within close proximity to the back-up anvil. For a given material, it is believed that unique forces are generated relative to the distance between the welding probe and the anvil. The forces have been measured and characterized for several materials, and correlations have been made between these forces and the pin's position relative to the backside of the weld material.

Ding, R. Jeffrey↗

NASA NTRS2009

Pin Tool Geometry Effects in Friction Stir Welding

In friction stir welding (FSW) there is significant evidence that material can take one of two different flow paths when being displaced from its original position in front of the pin tool to its final position in the wake of the weld. The geometry of the pin tool, along with the process parameters, plays an important role in dictating the path that the material takes. Each flow path will impart a different thermomechanical history on the material, consequently altering the material microstructure and subsequent weld properties. The intention of this research is to isolate the effect that different pin tool attributes have on the flow paths imparted on the FSWed material. Based on published weld tool geometries, a variety of weld tools were fabricated and used to join AA2219. Results from the tensile properties and microstructural characterization will be presented.

Querin, J. A.↗

NASA NTRS2011

Implementation of Pin Point Landing Vision Components in an FPGA System

Pin-point landing is required to enable missions to land close, typically within 10 meters, to scientifically important targets in generally hazardous terrain. In Pin Point Landing both high accuracy and high speed estimation of position and orientation is needed to provide input to the control system to safely choose and navigate to a safe landing site. A proposed algorithm called VISion aided Inertial NAVigation (VISINAV) has shown that the accuracy requirements can be met. [2][3] VISINAV was shown in software only, and was expected to use FPGA enhancements in the future to improve the computational speed needed for pin point landing during Entry Descent and Landing (EDL). Homography, feature detection and spatial correlation are computationally intensive parts of VISINAV. Homography aligns the map image with the descent image so that small correlation windows can be used, and feature detection provides regions that spatial correlation can track from frame to frame in order to estimate vehicle motion. On MER the image Homography, Feature Detection and Correlation would take approximately 650ms tracking 75 features between frames. We implemented Homography, Feature detection and Correlation on a Virtex 4 LX160 FPGA to run in under 25ms while tracking 500 features to improve algorithm reliability and throughput.

aircraft landing guidance↗

NASA NTRS2016

Silicon Alignment Pins: An Easy Way to Realize a Wafer-To-Wafer Alignment

A silicon alignment pin is used to align successive layers of components made in semiconductor chips and/or metallic components to make easier the assembly of devices having a layered structure. The pin is made as a compressible structure which can be squeezed to reduce its outer diameter, have one end fit into a corresponding alignment pocket or cavity defined in a layer of material to be assembled into a layered structure, and then allowed to expand to produce an interference fit with the cavity. The other end can then be inserted into a corresponding cavity defined in a surface of a second layer of material that mates with the first layer. The two layers are in registry when the pin is mated to both. Multiple layers can be assembled to create a multilayer structure. Examples of such devices are presented.

Jung-Kubiak, Cecile↗