SEARCH · Engineering Papers

Results for “Operational design domain”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

All sources NASA NTRS DOE OSTI

NASA NTRS1989

Intelligent Welding Controller

Control system adapts to changing design requirements and operating conditions. Proposed control system for gas/tungsten arc welding requires only that operator specifies such direct parameters of welds as widths and depths of penetration. In control system for robotic welder, components and functions intimately connected with welding process assigned to controller domain. More general functions assigned to supervisor domain. Initial estimate of indirect parameters of welding process applied to system only at beginning of weld (t=0); after start of welding, outputs from multivariable controller takes place of estimate.

Cook, George E.↗

NASA NTRS2005

Hubble Space Telescope Magnetometer and Two-Gyro Control Law Design, Implementation, and On-Orbit Performance

For f i h years, the science mission of the Hubble Space Telescope (HST) required using at least three of six rate gyros for attitude control. In the past, HST has mitigated gyro hardware failures by replacement of the failed units through Space Shuttle Servicing Missions. Following the tragic loss of Space Shuttle Columbia on STS-107, the desire to have a safe haven for astronauts during missions has resulted in the cancellation of all planned maxu14 missions to HST. While a robotic servicing mission is being currently being planned, controlling with alternate sensors to replace failed gyros can extend the HST Science mission until the robotic mission can be performed and extend science at HST s end of life. A two-gym control law has been designed and implemented using magnetometers (Magnetic Sensing System - MSS), fixed head star trackers (FHSTs), and Fine Guidance Sensors (FGSs) to control vehicle rate about the missing gyro axis. The three aforementioned sensors are used in succession to reduce HST boresight jitter to less than 7 milli-arcseconds rms and attitude error to less than 10 milli-arcseconds prior to science imaging. The MSS and 2-Gyro (M2G) control law is used for large angle maneuvers and attitude control during earth occultation of FHSTs and FGSs. The Tracker and 2-Gyro (T2G) control law dampens M2G rates and corrects the majority of attitude error in preparation for guide star acquisition with the FGSs. The Fine Guidance Sensor and 2-Gyro (F2G) control law d a m p T2G rates and controls HST attitude during science imaging. This paper describes the M2G control law. Details of M2G algorithms are presented, including computation of the HST 3-axis attitude error estimate, design of the M2G control law, SISO hear stability analyses, and restrictions on operations to maintain the h d t h and safety requirement of a 10degree maximum attitude error. Results of simulations performed in HSTSIM, a high-fidelity non-linear time domain simulation, are presented to predict HST on-orbit performance in attitude hold and maneuver modes. Simulation results are compared to on-orbit data from M2G flight tests performed in November and December 2004 and February 2005. Flight telemetry, using a currently available third gyro, shows that HST attitude error with the new M2G control law is maintained below the 10-degree requirement, and attitude errors are under 2 degrees for 95% of the time.

Wirzburger, John H.↗

NASA NTRS2010

Factors Influencing Scanning for Alerts

Aircraft pilots (like operators in many domains) are required to monitor locations for rare events, while concurrently performing their everyday tasks. In many cases, the visual parameters of the alert are such that it is not visible unless directly fixated. For this reason, critical alerts should be designed to be visible in peripheral vision and/or augmented by an audio alarm. We use the term "conspicuity" to distinguish the attention-getting power of a visual stimulus from simple visibility in a single-task context. We have measured conspicuity in an experimental paradigm designed to test the N-SEEV model of attention and noticing (Steelman-Allen et al., HFES 2009). The subject performed a demanding central task while monitoring four peripheral locations for color change events. Visibility of the alerting stimuli was measured separately in a control experiment in which the subject maintained steady fixation without the central task. Thresholds in the dual-task experiments were lower than would be expected based on the results of the control experiment, due to the fact that the subjects actively sampled the alert locations with fixations while performing the central task. Locations of high-frequency alerts are generally sampled more often than locations of low-frequency alerts, and alert location sampling in general increases with practice, presumably because the demands of the central task are reduced.

Mulligan, Jeffrey B.↗

NASA NTRS2019

Using Science Operations Tools and Methods from NASA for Remote Presence Ocean Exploration on Earth: E/V Nautilus Cruise NA108

NASA Ames' Exploration Ground Data Systems (xGDS) supports rapid scientific decision making by synchronizing information in time and space, including video and still images, scientific instrument data, and science and operations notes in geographic and temporal context. We have deployed xGDS at multiple NASA field analog missions over the past decade.In the last two years, we have participated in SUBSEA, a multi-institution collaborative project. SUBSEA used the research ship E/V Nautilus along with its two remotely operated vehicles (ROVs), Hercules and Argus, to explore deep ocean volcanic vents as an analog for ocean worlds (e.g. Enceladus). This work allowed us to compare the existing oceanographic operations methods and technologies used for ocean exploration with corresponding tools and approaches developed and used at NASA. In the first year of SUBSEA we observed existing remote science operations from the Inner Space Center (ISC). In the second year, we deployed xGDS at ISC to complement existing capabilities with xGDS tools designed to support remote Nautilus science operations from the ISC. During operations, video, ROV position and instrument telemetry were streamed from the ship to the ISC. As the science team watched dive operations, they could annotate the data with observations that were relevant to their work domain. Later, the team members could review the data at their own pace to collaboratively develop a dive plan for the next day, which had to be delivered on a fixed daily schedule.The opportunity to compare operations under different conditions enabled us to make several key observations about conducting remote science and planning operations efficiently: (i) Reviewing data collaboratively and interactively with temporal and spatial context was critical for the remote science team's ability to plan dive operations on the Nautilus. (ii) Science team members were actively engaged with the remote dive operations because they could interact with the collected data and visualize it as they desired. (iii) Being able to replay past events at accelerated speeds, and jump to points in time and spaced based on search results, provided efficient access to critical points of interest in a massive volume of data, so the remote science team could deliver plans on time. SUBSEA (Systematic Underwater Biogeochemical Science and Exploration Analog) is a multi-institution collaboration supported by NASA, NOAA's Office of Exploration Research (OER), the Ocean Exploration Trust (OET) and the University of Rhode Island's Graduate School of Oceanography (GSO). ISC is GSO's telepresence operations facility.

Lees, David S.↗

NASA NTRS2020

Conducting Efficient Remote Science and Planning Operations for Ocean Exploration Using Exploration Ground Data Systems (xGDS)

NASA Ames’ Exploration Ground Data Systems (xGDS) supports rapid scientific decision making by synchronizing information in time and space, including video and still images, scientific instrument data, and science and operations notes in geographic and temporal context. We have deployed xGDS at multiple NASA field analog missions over the past decade. In the last two years, we have participated in SUBSEA, a multi-institution collaborative project*. SUBSEA used the research ship E/V Nautilus along with its two remotely operated vehicles (ROVs), Hercules and Argus, to explore deep ocean volcanic vents as an analog for ocean worlds (e.g. Enceladus). This work allowed us to compare the existing oceanographic operations methods and technologies used for ocean exploration with corresponding tools and approaches developed and used at NASA. In the first year of SUBSEA we observed existing remote science operations from the Inner Space Center (ISC)**. In the second year, we deployed xGDS at ISC to complement existing capabilities with xGDS tools designed to support remote Nautilus science operations from the ISC. During operations, video, ROV position and instrument telemetry were streamed from the ship to the ISC. As the science team watched dive operations, they could annotate the data with observations that were relevant to their work domain. Later, the team members could review the data at their own pace to collaboratively develop a dive plan for the next day, which had to be delivered on a fixed daily schedule. The opportunity to compare operations under different conditions enabled us to make several key observations about conducting remote science and planning operations efficiently: (i) Reviewing data collaboratively and interactively with temporal and spatial context was critical for the remote science team’s ability to plan dive operations on the Nautilus. (ii) Science team members were actively engaged with the remote dive operations because they could interact with the collected data and visualize it as they desired. (iii) Being able to replay past events at accelerated speeds, and jump to points in time and spaced based on search results, provided efficient access to critical points of interest in a massive volume of data, so the remote science team could deliver plans on time. * SUBSEA (Systematic Underwater Biogeochemical Science and Exploration Analog) is a multi-institution collaboration supported by NASA, NOAA’s Office of Exploration Research (OER), the Ocean Exploration Trust (OET) and the University of Rhode Island’s Graduate School of Oceanography (GSO).

Cohen, Tamar E.↗

NASA NTRSDate not supplied

Comparison of Two Community Noise Models Applied to a NASA Urban Air Mobility Concept Vehicle

Predictions of community noise exposure from a NASA urban air mobility (UAM) concept vehicle have been conducted for representative operations using the FAA Aviation Environmental Design Tool (AEDT) in order to demonstrate modeling tool interoperability and assess applicability, capabilities and limitations of integrated noise modeling tools. To both quantify limitations and highlight other capabilities, a comparative analysis is performed using a time-domain simulation method, in particular, using the Volpe Advanced Acoustic Model (AAM). Using the same source noise model, the 3D directivity of a UAM concept vehicle is predicted in terms of aeroacoustic pressure time histories at a sphere of observer positions near the vehicle. In addition to distilling those data to a set of noise-power-distance data for input to AEDT, the data are processed preserving spectral directivity, into one-third and one-twelfth octave bands for input to AAM. Results from AEDT and AAM modeling are provided for a variety of metrics to demonstrate the effect that source noise directivity and propagation modeling fidelity have on predicted results at receptors over a study area.

urban air mobility↗

NASA NTRSDate not supplied

Comparison of Two Community Noise Models Applied to a NASA Urban Air Mobility Concept Vehicle

urban air mobility↗

DOE OSTI2021

Numerical Simulations of Geologic Storage Reservoir Management to Support Risk Mitigation Evaluation

This report provides a detailed description of a set of numerical simulations that represent reservoir behavior over time in response to different operational decision scenarios for detection of potential leakage and reduction or avoidance of leakage impact at a hypothetical geological carbon storage (GCS) site. These simulations serve as the basis for a series of GCS leakage risk forecasts that are to be developed using the National Risk Assessment Partnership’s Open-Source Integrated Assessment Model (NRAP-Open-IAM), and a demonstration of a simple decision support workflow for evaluation of mitigation strategies based on results of those system model forecasts. This risk assessment and decision support study is forthcoming. Four injection scenarios were considered: a constant rate carbon dioxide (CO 2 ) injection case (base case), a case with CO 2 injection rate adjustment, a case with early termination of injection operations, and a case with brine extraction. CO 2 injection operations were controlled to ensure that the pressure transient remains below the defined manageable reservoir fracture pressure, with consideration shown to hypothetical locations within the modeled spatial domain where the overburden was weaker and lower transient pressure increases were allowable. Additionally, a brine extraction alternative was considered as a reservoir management and risk mitigation option to reduce reservoir pressure, steer the plume away from any hypothetical geohazard such as fault as needed, and enhance storage capacity. Such operational actions contribute to risk management overtime. This study explores the potential utility of reservoir management for risk reduction at GCS sites. This study shows that the injection design may modify the time to CO 2 breakthrough at a legacy well; in particular, these results show that brine extraction can add value for mitigating risk both by delaying leakage and reducing pressure build-up. For the scenario considered, both pressure plots and pressure distributions demonstrate that pressure build-up was decreased by 3% with brine extraction. Additionally, extraction of brine afforded enhancement of CO 2 storage capacity by 5% compared to the base case. These findings suggest that brine extraction has substantial potential to steer the risk-related reservoir effects away from known geohazards (e.g., faults and legacy wells) by conducting pressure transient effects and CO 2 plume movement toward the production well. Injection rate adjustment scenarios considered in this study show potential value for managing both reservoir pressure transients and CO 2 plume behavior. Operational actions for reducing injection and/or early termination of injection (as compared to the base case), however, require careful design; tailoring both the extent and timing of injection rate adjustment over the injection and post-injection operational period must be thoroughly planned to balance maximizing storage and minimizing subsurface environmental risk. The study also gives preliminary consideration to the effectiveness that monitoring strategy may play in providing useful information to inform reservoir management decisions for risk reduction. Two types of monitoring were considered: 1) pressure build-up or pressure transient; and 2) potential leakage detection from a CO 2 mass or plume. Four hypothetical legacy wells, two plugged and two abandoned, were placed in the model domain. Monitoring along these wells was measured over time in individual stacked reservoir formations and shale formations to support risk mitigation decisions, especially operational decisions that assisted in risk reduction. These simulations will serve as the basis for a series of GCS leakage risk forecasts that are to be developed using NRAP’s Open-IAM, and demonstration of a simple decision support workflow for comparative assessment of mitigation alternatives based on results of those system model forecasts. This risk assessment and decision support study is forthcoming.

54 ENVIRONMENTAL SCIENCES↗

NASA NTRS2010

Workload: Measurement and Management

Poster: The workload research project has as its task to survey the available literature on: (1) workload measurement techniques; and (2) the effects of workload on operator performance. The first set of findings provides practitioners with a collection of simple-to-use workload measurement techniques along with characterizations of the kinds of tasks each technique has been shown reliably address. This allows design practitioners to select and use the most appropriate techniques for the task(s) at hand. The second set of findings provides practitioners with the guidance they need to design for appropriate kinds and amounts of workload across all tasks for which the operator is responsible. This guidance helps practitioners design systems and procedures that ensure appropriate levels of engagement across all tasks, and avoid designs and procedures that result in operator boredom, complacency, loss of awareness, undue levels of stress, or skill atrophy that can result from workload that distracts operators from the tasks they perform and monitor, workload levels that are too low, too high, or too consistent or predictable. Only those articles that were peer reviewed, long standing and generally accepted in the field, and applicable to a relevant range of conditions in a select domain of interest, in analogous "extreme" environments to those in space were included. In addition, all articles were reviewed and evaluated on uni-dimensional and multi-dimensional considerations. Casner & Gore also examined the notion of thresholds and the conditions that may benefit mostly from the various methodological approaches. Other considerations included whether the tools would be suitable for guiding a requirement-related and design-related question. An initial review of over 225 articles was conducted and entered into an EndNote database. The reference list included a range of conditions in the domain of interest (subjective/objective measures), the seminal works in workload, as well as summary works

Gore, Brian Francis↗

DOE OSTI2022

MIONet: Learning Multiple-Input Operators via Tensor Product

As an emerging paradigm in scientific machine learning, neural operators aim to learn operators, via neural networks, that map between infinite-dimensional function spaces. Several neural operators have been recently developed. However, all the existing neural operators are only designed to learn operators defined on a single Banach space; i.e., the input of the operator is a single function. Here, for the first time, we study the operator regression via neural networks for multiple-input operators defined on the product of Banach spaces. We first prove a universal approximation theorem of continuous multiple-input operators. We also provide a detailed theoretical analysis including the approximation error, which provides guidance for the design of the network architecture. Based on our theory and a low-rank approximation, we propose a novel neural operator, MIONet, to learn multiple-input operators. MIONet consists of several branch nets for encoding the input functions and a trunk net for encoding the domain of the output function. Here, we demonstrate that MIONet can learn solution operators involving systems governed by ordinary and partial differential equations. In our computational examples, we also show that we can endow MIONet with prior knowledge of the underlying system, such as linearity and periodicity, to further improve accuracy.

97 MATHEMATICS AND COMPUTING↗

NASA NTRS1993

The Consolidated Planning and Scheduling System for Space Transportation and Space Station operations - Successful development experience

In 1992, NASA made the decision to evolve a Consolidated Planning System (CPS) by adding the Space Transportation System (STS) requirements to the Space Station Freedom (SSF) planning software. This paper describes this evolutionary process, which began with a series of six-month design-build-test cycles, using a domain-independent architecture and a set of developmental tools known as the Advanced Scheduling Environment. It is shown that, during these tests, the CPS could be used at multiple organizational levels of planning and for integrating schedules from geographically distributed (including international) planning environments. The potential for using the CPS for other planning and scheduling tasks in the SSF program is being currently examined.

Hornstein, Rhoda S.↗

NASA NTRS1999

PARAMESH: A Parallel Adaptive Mesh Refinement Community Toolkit

In this paper, we describe a community toolkit which is designed to provide parallel support with adaptive mesh capability for a large and important class of computational models, those using structured, logically cartesian meshes. The package of Fortran 90 subroutines, called PARAMESH, is designed to provide an application developer with an easy route to extend an existing serial code which uses a logically cartesian structured mesh into a parallel code with adaptive mesh refinement. Alternatively, in its simplest use, and with minimal effort, it can operate as a domain decomposition tool for users who want to parallelize their serial codes, but who do not wish to use adaptivity. The package can provide them with an incremental evolutionary path for their code, converting it first to uniformly refined parallel code, and then later if they so desire, adding adaptivity.

MacNeice, Peter↗

NASA NTRS2005

Requirements to Design to Code: Towards a Fully Formal Approach to Automatic Code Generation

A general-purpose method to mechanically transform system requirements into a provably equivalent model has yet to appear. Such a method represents a necessary step toward high-dependability system engineering for numerous possible application domains, including distributed software systems, sensor networks, robot operation, complex scripts for spacecraft integration and testing, and autonomous systems. Currently available tools and methods that start with a formal model of a system and mechanically produce a provably equivalent implementation are valuable but not sufficient. The gap that current tools and methods leave unfilled is that their formal models cannot be proven to be equivalent to the system requirements as originated by the customer. For the classes of systems whose behavior can be described as a finite (but significant) set of scenarios, we offer a method for mechanically transforming requirements (expressed in restricted natural language, or in other appropriate graphical notations) into a provably equivalent formal model that can be used as the basis for code generation and other transformations.

Hinchey, Michael G.↗

NASA NTRS2005

Requirements to Design to Code: Towards a Fully Formal Approach to Automatic Code Generation

A general-purpose method to mechanically transform system requirements into a provably equivalent model has yet to appear. Such a method represents a necessary step toward high-dependability system engineering for numerous possible application domains, including distributed software systems, sensor networks, robot operation, complex scripts for spacecraft integration and testing, and autonomous systems. Currently available tools and methods that start with a formal model of a: system and mechanically produce a provably equivalent implementation are valuable but not sufficient. The "gap" that current tools and methods leave unfilled is that their formal models cannot be proven to be equivalent to the system requirements as originated by the customer. For the ciasses of systems whose behavior can be described as a finite (but significant) set of scenarios, we offer a method for mechanically transforming requirements (expressed in restricted natural language, or in other appropriate graphical notations) into a provably equivalent formal model that can be used as the basis for code generation and other transformations.

Hinchey, Michael G.↗

DOE OSTI2023

Enabling Interconnected Science Workflows through an Adapter Approach

The INTERSECT Software framework project aims to create an open federated library that connects, coordinates, and controls systems in the scientific domain. It features the Adapter, a flexible and extensible interface inspired by the Adapter design pattern in object-oriented programming. By utilizing Adapters, the INTERSECT SDK enables effective communication and coordination within a diverse ecosystem of systems. This adaptability facilitates the execution of complex operations within the framework, promoting collaboration and efficient workflow management in scientific research. Additionally, the generalizability of Adapters and their patterns enhances their utility in other scientific software projects and challenges.

McGaha, Jesse↗

NASA NTRSDate not supplied

Identifying Human Errors and Error Mechanisms From Accident Reports Using Large Language Models

Emerging operational concepts for aviation hinge on novel paradigms for human machine interaction. Critical to their safe operation is early consideration of human error into the design process. Existing methods for consideration of human error require significant expert input, which is challenging both in early design and in novel systems for which there is little existing safety expertise. In this research, we propose a methodology for identifying human error, error producing factors, and mechanisms in early design from historical incident reports. Additionally, we hypothesize that cross-domain sharing of lessons learned can aid with early design human considerations in circumstances where data is not relevant or incomplete. This is addressed by identifying causes of human error in aviation and railway domains through applying state-of-the art natural language processing techniques to historical incident reports. Using this method, it is possible to extract extensive reports on human error from past incidents. Using the proposed approach, we identify nine human errors from railway reports and fourteen from aviation reports, with three errors common to both domains. There is at least one error producing conditions for each human error while a majority of the errors have more than one error mechanism. We also found that a majority of the human errors, error producing factors, and error mechanisms (even if they are not common between the domains) can be used to inform safe operations across domains as long as the errors are not domain specific and are interpreted and contextualized using engineering judgement.

Human Errors↗

NASA NTRS1989

Frequency domain identification experiment on a large flexible structure

Recent experiences in the field of flexible structure control in space have indicated a need for on-orbit system identification to support robust control redesign to avoid in-flight instabilities and maintain high spacecraft performance. The authors highlight an automated frequency domain system identification methodology recently developed to fill this need. The methodology supports (1) the estimation of system quantities useful for robust control analysis and design, (2) experiment design tailored to performing system identification in a typically constrained on-orbit environment, and (3) the automation of operations to reduce human-in-the-loop requirements. A basic overview of the methodology is presented first, followed by an experimental verification of the approach performed on the JPL/AFAL testbed facility.

Bayard, D. S.↗

NASA NTRS1989

Prototype software reuse environment at Goddard Space Flight Center

The Goddard Space Flight Center (GSFC) work is organized into four phases and includes participation by a contractor, CTA, Inc. The first phase was an automation study, which began with a comprehensive survey of software development automation technologies. Eight technical areas were analyzed for goals, current capabilities, and obstacles. The study documented current software development practice in GSFC Mission Operations and Data Systems Directorate, and presented short- and long-term recommendations that included focus on reuse and object-oriented development. The second phase, which has been completed, developed a prototype reuse environment with tools supporting object-oriented requirements analysis and design. This phase addressed the operational concept of software reuse, i.e., it attempted to understand how software can be reused. This environment has two semantic networks: object and keywords, and includes automated search, interactive browsing and a graphical display of database contents. Phase 3 was a domain analysis of Payload Operations Control Center (POCC) software. The goal in this phase was to create an initial repository of reusable components and techniques. Seven existing Operations Control Centers at GSFC were studied, but the domain analysis proved to be very slow. A lesson learned from this was that senior people who understand the environment and the functionality of the area are needed to perform successful domain analyses.

Truszkowski, Walt↗