Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Multilayer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
DOE OSTI2018

The influence of deposition conditions and bilayer thickness on physical-mechanical properties of CA-PVD multilayer ZrN/CrN coatings

Highlights: • Multilayer ZrN/CrN coatings were deposited using Arc-PVD AISI321 steel substrates. • Structure, elemental and phase composition, and mechanical properties were studied. • Presence of face-centered cubic ZrN, CrN and hexagonal Cr{sub 2}N phases were detected. • All samples were heated up to 1400 °C in argon to understand thermal behavior. • Enhancement of microhardness was observed at lower values of bilayer thickness. - Abstract: ZrN/CrN multilayers have been produced by a cathodic arc technique (CA-PVD) using different depositions conditions. Microstructural and mechanical characterizations of the coatings were performed by X-ray diffraction (XRD), scanning electron microscopy with energy dispersive spectroscopy (SEM with EDS), transmission electron microscopy (TEM), and Vickers microhardness tests. Variations in thermal transformation properties due to heating within the temperature range from 30 °C to 1400 °C were studied by differential scanning calorimetry (DSC) measurements. SEM and TEM observations showed that the coatings comprise a multilayered structure with nanometric grains. EDS spectra confirmed the formation of stoichiometric composition. Near-to-super stoichiometric nitrides can be suggested in certain specimens. Results of the XRD analysis revealed that the (200) and (111) planes for ZrN and Cr{sub 2}N are the most intense. Calorimetric tests showed that below a certain annealing temperature no transformations were defined. 1180 °C was found to be the value where only one-stage state transformation, presented by endothermic or exothermic reactions, took place. The highest hardness (4685HV0.025) was obtained for the coating with Λ = 140 nm, P{sub N} = 0.43 Pa, U{sub S} = −70 V.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Characterization of nanocrystallised multilayered metallic materials produced by the SMAT followed by constrained compression

Highlights: • Nanocrystallised multilayered metallic material was produced by novel technique. • Bonding between nanocrystallised plates was achieved by constrained compression. • The metal-metal bonding occurred between fragmented oxide layers. • A high degree of structural inhomogeneity was observed near bonded regions. - Abstract: Nanocrystallised multilayered metallic material was obtained via duplex technique combining the surface mechanical attrition treatment (SMAT) with a novel constrained compression (CC) process. At the initial stage the 1 mm thick sheets of 316L austenitic stainless steel were processed by the SMAT in order to form a nanocrystalline structure. At the final stage disc-shaped plates excised from SMATed sheets, were assembled in a package and compressed in order to produce metallurgical bonding between individual plates. The characterization of such a multilayered structure was studied both experimentally and numerically. The microscopic examination revealed that the bonding occurred in the central portions of the package where the oxide scale covering each plate was fragmented by high shear strains. The numerical analysis confirmed that the strains at the interior interfaces are significantly higher than at the external ones. A high degree of structural inhomogeneity was observed via TEM studies in the regions where the successful bonding was achieved. Regions characterised by fine band structure with the presence of α′-martensite phase as well as coarse cellular structure within a single γ-austenite phase were identified.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2013

Ground-state energy trends in single and multilayered coupled InAs/GaAs quantum dots capped with InGaAs layers: Effects of InGaAs layer thickness and annealing temperature

Graphical abstract: - Highlights: • Investigation of ground state energy in single and multi-layered InAs/GaAs QD. • Strain reducing layer (InGaAs) prevents the formation of non-radiative. • Strain reducing layer (InGaAs) is responsible for high activation energy. • Significant deviation from the Varshni model, E(T) = E − αT{sup 2}/T + β. - Abstract: Vertically coupled, multilayered InAs/GaAs quantum dots (QDs) covered with thin InGaAs strain-reducing layers (SRLs) are in demand for various technological applications. We investigated low temperature photoluminescence of single and multilayered structures in which the SRL thickness was varied. The SRL layer was responsible for high activation energies. Deviation of experimental data from the Varshni (1967) model, E(T) = E − ∞ T{sup 2}/T + β, suggests that the InAs-layered QDs have properties different from those in bulk material. Anomalous ground-state peak linewidths (FWHM), especially for annealed multilayer structures, were observed. A ground-state peak blue-shift with a broadened linewidth was also observed. Loss of intensity was detected in samples annealed at 800 °C. Presence of SRLs prevents formation of non-radiative centers under high temperature annealing. The results indicate the potential importance of such structures in optoelectronic applications.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Activation energy and carriers dynamics of multilayer CdTe/ZnTe quantum dots with different ZnTe separation layer thicknesses

We studied the optical properties of multilayer CdTe/ZnTe quantum dots (QDs) with various ZnTe separation layer thicknesses on GaAs substrates. The low temperature photoluminescence (PL) spectra show that the excitonic peaks in multilayer CdTe/ZnTe QDs shift to higher energy levels, and PL peak intensities increase with increasing ZnTe separation layer thickness. This is because of increasing uncoupling and because there are many more carriers confined in the QDs with wider separation layers. Temperature-dependent PL measurements showed that the activation energies of the confined electrons in the multilayer CdTe/ZnTe QDs decreases with decreasing ZnTe separation layer thickness. The time-resolved PL spectra show increasing carrier decay times with decreasing ZnTe separation layer thickness, due to increasing coupling between QDs with narrower separation layers.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Comparison of effects from gamma, e-beam and X-ray radiation on multilayer polymer films used in biopharmaceutical devices by chemometric treatment of spectroscopic data

The present study investigated the effects of gamma-ray, electron beam, and X-ray radiation on polymers in EVA/EVOH/EVA multilayer films. Spectroscopic methods, including FTIR and UV–Vis, were employed in conjunction with chemometric treatments such as PCA, SIMPLISMA treatments, and PLS models. The feasibility of dose prediction on multilayer film, given a known dose, is attainable across various irradiation technologies. Both gamma ray and X-ray exhibit comparable effects on the multilayer film, and it is feasible to anticipate the dose released on the film by utilizing UV–Vis spectra or infrared spectra for gamma ray or X-ray of a predetermined dose.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2016

The width of the lateral element of the synaptonemal complex is determined by a multilayered organization of its components

The synaptonemal complex (SC) is a proteinaceous structure that holds the homologous chromosomes in close proximity while they exchange genetic material in a process known as meiotic recombination. This meiotic recombination leads to genetic variability in sexually reproducing organisms. The ultrastructure of the SC is studied by electron microscopy and it is observed as a tripartite structure. Two lateral elements (LE) separated by a central region (CR) confer its classical tripartite organization. The LEs are the anchoring platform for the replicated homologous chromosomes to properly exchange genetic material with one another. An accurate assembly of the LE is indispensable for the proper completion of meiosis. Ultrastructural studies suggested that the LE is organized as a multilayered unit. However, no validation of this model has been previously provided. In this ultrastructural study, by using mice with different genetic backgrounds that affect the LE width, we provide further evidence that support a multilayered organization of the LE. Additionally, we provide data suggesting additional roles of the different cohesin complex components in the structure of the LEs of the SC. - Highlights: • The lateral element of the synaptonemal complex is a multilayered structure. • The width of the lateral element in synaptonemal complex-null mice is different. • Two cohesin complex cores plus one axial element form a wild-type lateral element. • The layers of the lateral element can be analyzed in different null mice models.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2023

Dynamics of multilayer Rayleigh–Taylor instability at moderately high Atwood numbers

This paper investigates the multilayer Rayleigh–Taylor instability (RTI) using statistically stationary experiments conducted in a gas tunnel. Employing diagnostics such as particle image velocimetry (PIV) and planar laser induced fluorescence (PLIF), we make simultaneous velocity–density measurements to study how dynamics and mixing are linked in this variable density flow. Experiments are conducted in a newly built, blow-down three-layer gas tunnel facility. Mixing between three gas streams is studied, where the top and bottom streams are comprised of air, and the middle stream is an air–helium mixture. Shear is minimized between these streams by matching their inlet velocities. The four experimental conditions investigated here consist of two different density ratios (Atwood numbers 0.3 and 0.6), each investigated at two instability development times (or equivalently, two streamwise locations), and all experiments are with the same middle stream thickness of 3 cm. The growth of the middle layer is measured using laser-based planar Mie scattering visualization. The mixing width is found to grow linearly with time at late times. Various quantitative measures of molecular mixing indicate a very high degree of molecular mixing at late times in the multilayer RTI flow. The vertical turbulent mass flux $a_y$ is calculated. In addition to mostly negative values of $a_y$ , typical of buoyancy-dominated flows due to negative correlation between velocity and density fluctuations, positive regions are also observed in profiles of $a_y$ due to entrainment and erosion at the lower edge of the mixing region. Global energy budgets are calculated for the multilayer RTI flow at late times and it is found that the majority of potential energy released has been dissipated due to viscous effects, and a large value of mixing efficiency ( $\sim$ 60 %) is observed.

Mechanics↗
DOE OSTI2018

Flat-On Secondary Crystals as Effective Blocks To Reduce Ionic Conduction Loss in Polysulfone/Poly(vinylidene fluoride) Multilayer Dielectric Films

Recently, poly(vinylidene fluoride) (PVDF)-based multilayer films have demonstrated good potential as high energy density, high temperature, and low loss polymer dielectrics for advanced electrical and power applications. However, impurity ion conduction in the PVDF layers can cause significant dielectric loss at high temperatures. In this study, we discovered a facile melt-recrystallization method to suppress ionic conduction loss in polysulfone (PSF)/PVDF 50/50 (v/v) 33-layer films. By use of combined differential scanning calorimetry, broadband dielectric spectroscopy, and simultaneous small-angle X-ray scattering/wide-angle X-ray diffraction techniques, the underlying mechanism for the suppression of ionic conduction was unraveled. Basically, the growth and hierarchical organization of primary and secondary PVDF crystals confined in 400 nm layers played an important role. When the cooling rate during melt-recrystallization was high (e.g., ≥ 500 °C/min), small and poorly oriented secondary crystals between orderly stacked edge-on primary crystals allowed free transport of impurity ions in PVDF layers. At low to moderate cooling rates (i.e., <100 °C/min), growth of flat-on secondary crystals between the edge-on primary crystalline lamellae blocked the transport of impurity ions, suppressing the dielectric loss from ionic conduction. On the basis of this paper, we propose a modified multilayer coextrusion method with controlled cooling rates to achieve flat-on secondary crystals for the reduction of high temperature dielectric loss in PVDF-based multilayer dielectric films.

36 MATERIALS SCIENCE↗
DOE OSTI2018

High Selectivities among Monovalent Cations in Dialysis through Cation-Exchange Membranes Coated with Polyelectrolyte Multilayers

Cation-exchange membranes allow preferential passage of cations over anions, but they show minimal selectivity among cations, which limits their use in ion separations. Recent studies show that modification of cation-exchange membranes with polyelectrolyte multilayers leads to exceptional monovalent/divalent cation electrodialysis selectivities, but no studies report high selectivity among monovalent ions. Here, this work demonstrates that adsorption of protonated poly(allylamine) (PAH)/poly(4-styrenesulfonate) (PSS) multilayers on Nafion membranes leads to high K + /Li + selectivities in Donnan dialysis, where K + and Li + ions in a source phase pass through the membrane and exchange with Na + ions in a receiving phase. Addition of 0.01 M HNO 3 to a source phase containing 0.01 M KNO 3 and 0.01 M LiNO 3 increases the K + /Li + selectivity from 8 to ~60 through (PAH/PSS) 5 PAH-coated Nafion membranes, primarily because of a ≥fivefold increase in K + flux. These selectivities are much larger than the ratio of 1.9 for the aqueous diffusion coefficients of K + and Li + , and uncoated Nafion membranes give a K + /Li + selectivity <3. Bi-ionic transmembrane potential measurements at neutral pH confirm that the membrane is more permeable to K + than Li + , but this selectivity is less than in Donnan dialysis with acidic solutions. In situ ellipsometry data indicate that PAH/PSS multilayers (assembled at pH 2.3, 7.5, or 9.3) swell at pH 2.0, and this swelling may open cation-exchange sites that preferentially bind K + to enable highly selective transport. The coated membranes also exhibit modest selectivity for K + over H + , suggesting selective transport based on preferential partitioning of K + into the coatings. Selectivity declines when increasing the source-phase KNO 3 concentration to 0.1 M, perhaps because the discriminating transport pathway saturates. Finally, selectivities are lower in electrodialysis than in Donnan dialysis, presumably because electrodialysis engages other transport mechanisms, such as electroosmosis and strong electromigration.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Thermal-Strain-Enabled Enhanced Emission from UV Laser-Induced Defect Levels near the Surface of Multilayer MoS 2

Monolayer two-dimensional (2D) materials have been intensively studied while research on multilayers is still in its infancy. Here, we induce defects inside bulk MoS 2 through thermal annealing and near the surface of multilayer MoS 2 using 375 nm laser irradiation, and investigate their photoluminescence (PL) and fluorescence lifetime imaging (FLIM). Enhanced emission is limited within a certain MoS 2 thickness. The observed enhanced emission is evidenced by a threshold behavior in super-linear PL intensity increase, strong polarization effects, and increased lifetime of defect peak. The laser power threshold for enhanced emission is much smaller in defects near the surface than that inside the bulk of multilayer MoS 2 . The mechanical strain from a wrinkle of the sample further lowers the laser power threshold for enhanced emission. By exciting with a 639 nm laser that is close to the fundamental gap between the conduction band minimum and the valence band maximum, the lifetime of defect enhanced emission increased by 5 times. Furthermore, one of the competing indirect bandgap emissions disappears, and the defect emission peak dominates the PL spectrum in the wrinkle area with a strain. Furthermore, the discovered principle can be applied to future studies on the integration of enhanced emission and single photon emission involving selectively depopulating the conduction band of the host crystal to defect levels for quantum emitters.

2D materials↗
DOE OSTI2024

Toward Mass-Production of Transition Metal Dichalcogenide Solar Cells: Scalable Growth of Photovoltaic-Grade Multilayer WSe2 by Tungsten Selenization

Semiconducting transition metal dichalcogenides (TMDs) are promising for high-specific-power photovoltaics due to their desirable band gaps, high absorption coefficients, and ideally dangling-bond-free surfaces. Despite their potential, the majority of TMD solar cells to date are fabricated in a nonscalable fashion, with exfoliated materials, due to the lack of high-quality, large-area, multilayer TMDs. Here, we present the scalable, thickness-tunable synthesis of multilayer WSe2 films by selenizing prepatterned tungsten with either solid-source selenium at 900 degrees C or H2Se precursors at 650 degrees C. Both methods yield photovoltaic-grade, wafer-scale WSe2 films with a layered van der Waals structure and superior characteristics, including charge carrier lifetimes up to 144 ns, over 14x higher than those of any other large-area TMD films previously demonstrated. Simulations show that such carrier lifetimes correspond to ~22% power conversion efficiency and ~64 W g-1 specific power in a packaged solar cell, or ~3 W g-1 in a fully packaged solar module. The results of this study could facilitate the mass production of high-efficiency multilayer WSe2 solar cells at low cost.

carrier lifetime↗
DOE OSTI2022

Leakage From Coexisting Geologic Forcing and Injection‐Induced Pressurization: A Semi‐Analytical Solution for Multilayered Aquifers With Multiple Wells

Abstract Abnormal fluid pressures (above or below hydrostatic pressure) can develop and persist in sedimentary basins. The common occurrence of abnormal pressures may cause challenges for project permitting of geological carbon sequestration (GCS), particularly in reservoirs with pre‐injection overpressure. The leaky wells that may exist in some sedimentary basins can provide flow paths between deep brine aquifers and shallower freshwater aquifers. Pre‐injection relative overpressures can cause brine leakage through leaky wells even before any injection occurs. The tendency for flow through leaky wells is coupled with the process of pressure dissipation that occurs through aquitards. Specifically, with non‐zero permeability, aquitards can dissipate pressure over large areal extents and thereby reduce leakage rates through leaky wells. This study presents development of a semi‐analytical solution for hydraulic head and brine leakage in multilayered aquifer–aquitard systems with geologic pressure forcing. The geologic forcing that causes abnormal pressures in the multilayered system can coexist with any number of injection, extraction, and leaky wells that also affect fluid pressure. The semi‐analytical model is applied to explore how leakage through leaky wells varies as functions of pressurization rate, along with aquitard and leaky well properties in an overpressured multilayered system. The results show that although injection‐induced pressures can dissipate rapidly through suitably permeable aquitards, coexisting geologic forcing may create sustained rates of brine leakage into freshwater aquifers through leaky wells. In GCS, a very low‐permeability aquitard with high capillary entry pressure to free‐phase CO 2 is desired to serve as the caprock to prevent leakage of CO 2 from the storage reservoir. Nevertheless, the results from this study show that the brine leakage impact to shallow freshwater aquifers through leaky wells might substantially decrease with increasing aquitard permeability values, as long as small aquitard permeability and high capillary entry pressure serve to prevent CO 2 leakage.

Cihan, A.↗
DOE OSTI2017

Observation of stable Néel skyrmions in cobalt/palladium multilayers with Lorentz transmission electron microscopy

Néel skyrmions are of high interest due to their potential applications in a variety of spintronic devices, currently accessible in ultrathin heavy metal/ferromagnetic bilayers and multilayers with a strong Dzyaloshinskii–Moriya interaction. Here in this paper we report on the direct imaging of chiral spin structures including skyrmions in an exchange-coupled cobalt/palladium multilayer at room temperature with Lorentz transmission electron microscopy, a high-resolution technique previously suggested to exhibit no Néel skyrmion contrast. Phase retrieval methods allow us to map the internal spin structure of the skyrmion core, identifying a 25 nm central region of uniform magnetization followed by a larger region characterized by rotation from in- to out-of-plane. The formation and resolution of the internal spin structure of room temperature skyrmions without a stabilizing out-of-plane field in thick magnetic multilayers opens up a new set of tools and materials to study the physics and device applications associated with chiral ordering and skyrmions.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Ultrahigh photo-responsivity and detectivity in multilayer InSe nanosheets phototransistors with broadband response

In this paper, we demonstrate the strategies and principles for the performance improvement of layered semiconductor based photodetectors using multilayer indium selenide (InSe) as the model material. It is discovered that multiple reflection interference at the interfaces in the phototransistor device leads to a thickness-dependent photo-response, which provides a guideline to improve the performance of layered semiconductor based phototransistors. The responsivity and detectivity of InSe nanosheet phototransistor can be adjustable using applied gate voltage. Our InSe nanosheet phototransistor exhibits ultrahigh responsivity and detectivity. An ultrahigh external photo-responsivity of ~10 4 A W -1 can be achieved from broad spectra ranging from UV to near infrared wavelength using our InSe nanosheet photodetectors. The detectivity of multilayer InSe devices is ~10 12 to 10 13 Jones, which surpasses that of the currently exploited InGaAs photodetectors (10 11 to 10 12 Jones). Finally, this research shows that multilayer InSe nanosheets are promising materials for high performance photodetectors.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Atomistic simulation of PDADMAC/PSS oligoelectrolyte multilayers: overall comparison of tri- and tetra-layer systems

By employing large-scale molecular dynamics simulations of atomistically resolved oligoelectrolytes in aqueous solutions, we study in detail the first four layer-by-layer deposition cycles of an oligoelectrolyte multilayer made of poly(diallyl dimethyl ammonium chloride)/poly(styrene sulfonate sodium salt) (PDADMAC/PSS). The multilayers are grown on a silica substrate in 0.1 M NaCl electrolyte solutions and the swollen structures are then subsequently exposed to varying added salt concentration. We investigated the microscopic properties of the films, analyzing in detail the differences between three- and four-layer systems. Our simulations provide insights into the early stages of growth of a multilayer, which are particularly challenging for experimental observations. Here, we found rather strong complexation of the oligoelectrolytes, with fuzzy layering of the film structure. The main charge compensation mechanism is for all cases intrinsic, whereas extrinsic compensation is relatively enhanced for the layer of the last deposition cycle. In addition, we quantified other fundamental observables of these systems, such as the film thickness, water uptake, and overcharge fractions for each deposition layer.

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2020

Reducing dielectric loss and enhancing electrical insulation for multilayer polymer films by nanoconfined ion transport under high poling electric fields

High temperature polar polymers have demonstrated potential for good thermal stability and high dielectric constant at the same time. However, polarization of contaminated impurity ions in polar polymers, even at the ppm level, can significantly increase the dielectric loss at high temperature and low frequencies. One effective strategy to mitigate this problem is to multilayer them with a high temperature nonpolar dielectric polymer to confine impurity ion transport at the nanometer scale. In this study, confined ion transport in high temperature polycarbonate (HTPC)/poly(vinylidene fluoride) (PVDF) multilayer films under high AC electric fields was studied using a direct analytical simulation method. Different from the ion transport under low fields, the ion diffusion model failed to describe the ion transport under high electric fields. An exponential ion distribution profile, which was observed for the DC poling situation, was employed to implement the direct analytical simulation. Confined impurity ion transport under high AC fields was quantitatively understood. As the AC field increased, the mobile ion concentration decreased whereas the diffusion coefficient increased. The decrease of mobile ion concentration was explained by the blockage of impurity ions by the HTPC layers. This knowledge helped in the determination of optimal conditions to polarize impurity ions from the PVDF layers into the HTPC layers. After cooling below the glass transition temperature of HTPC, polarized impurity ions were locked inside the HTPC layers. As a result, increased discharge efficiency and enhanced electrical insulation (i.e., increased dielectric breakdown strength) were achieved for the polarized multilayer films.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Residual Stress and Opening-Mode Fracture Analysis of Multilayered Structures Subjected to Thermal Loading

Temperature change after formation commonly results in thermal residual stress in multilayered structures due to the different thermal and mechanical properties of each layer. In this paper, a three-dimensional (3D) elastic model is developed to study the residual stress and opening-mode fractures (OMFs) in a multilayered structure consisting of arbitrary number of layers under temperature change. The general solution of displacement field in the multilayered structure is derived by solving the elastic boundary value problem. In order to verify the proposed model, the elastic field in the advanced polymeric solar reflectors that consist of four layers is solved by applying the present model and compared with the finite-element (FE) simulation. In addition, parametric studies are conducted to investigate the effect of the thickness ratio between each layer on the accuracy of the developed model. As a result, based on the obtained elastic field, the fracture energy release rate (ERR) in the surface layer of the advanced polymeric reflector is obtained and used to study the fracture initiation, infilling, and saturation successfully.

36 MATERIALS SCIENCE↗
DOE OSTI2012

Study of multilayer-reflected beam profiles and their coherence properties using beamlines ID19 (ESRF) and 32-ID (APS)

The use of multilayer mirrors is an interesting alternative for reflective X-ray monochromatization with respect to reflection from crystal optics. The increased photon flux density due to the multilayers' larger bandwidth is of crucial importance for, e.g, full-field X-ray imaging applications. Drawbacks are the introduced modifications of the reflected beam profile as well as a certain loss of coherence, summarized as wavefront degradation. Our recent work has shown that the modification of the beam profile can vary with, e.g., the material composition of the coating applied. In order to verify our findings, a beamline round-robin has been initiated, comparing the wavefront profiles after reflection by selected multilayers at beamlines 32-ID (Advanced Photon Source) and ID19 (European Synchrotron Radiation Facility) with our initial results acquired at BM05 (ESRF) [1].

43 PARTICLE ACCELERATORS↗