Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Microstructure formation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

A Review of Existing and Emerging Methods for Lithium Detection and Characterization in Li-Ion and Li-Metal Batteries

Whether attempting to eliminate parasitic Li metal plating on graphite (and other Li-ion anodes) or enabling stable, uniform Li metal formation in ‘anode-free’ Li battery configurations, the detection and characterization (morphology, microstructure, chemistry) of Li that cannot be reversibly cycled is essential to understand the behavior and degradation of rechargeable batteries. In this review, various approaches used to detect and characterize the formation of Li in batteries are discussed. Each technique has its unique set of advantages and limitations, and works towards solving only part of the full puzzle of battery degradation. Going forward, multimodal characterization holds the most promise towards addressing two pressing concerns in the implementation of the next generation of batteries in the transportation sector (viz. reducing recharging times and increasing the available capacity per recharge without sacrificing cycle life). Such characterizations involve combining several techniques (experimental- and/or modeling-based) in order to exploit their respective advantages and allow a more comprehensive view of cell degradation and the role of Li metal formation in it. Additionally, it is also discussed which individual techniques, or combinations thereof, can be implemented in real-world battery management systems on-board electric vehicles for early detection of potential battery degradation that would lead to failure.

25 ENERGY STORAGE↗
DOE OSTI2023

Probing rutile solid-phase crystallization of atomically mixed Mn-alloyed TiO 2 coatings through XANES analysis

Phase transformation via dopant introduction is an emerging strategy for tuning the electronic and catalytic properties of oxides. However, developing a general theory of ternary alloys and their microstructure evolution remains challenging due to the knowledge gaps in how point defects such as dopants lead to the formation of complex or metastable phases. We investigate the influence of Mn concentration and annealing temperature on the microstructure evolution of amorphous Mn-alloyed TiO 2 synthesized via Atomic Layer Deposition. In conclusion, our findings reveal a new crystallization pathway resulting in a direct amorphous TiO 2 to rutile transformation without an intermediate anatase phase and our multi-parameter thermal processing conditions show potential for AI-assisted data acquisition and analysis for studying complex oxide coatings.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Controlled patterning of crystalline domains by frontal polymerization

Materials with hierarchical architectures that combine soft and hard material domains with coalesced interfaces possess superior properties compared with their homogeneous counterparts. These architectures in synthetic materials have been achieved through deterministic manufacturing strategies such as 3D printing, which require an a priori design and active intervention throughout the process to achieve architectures spanning multiple length scales. Here we harness frontal polymerization spin mode dynamics to autonomously fabricate patterned crystalline domains in poly(cyclooctadiene) with multiscale organization. This rapid, dissipative processing method leads to the formation of amorphous and semi-crystalline domains emerging from the internal interfaces generated between the solid polymer and the propagating cure front. The size, spacing and arrangement of the domains are controlled by the interplay between the reaction kinetics, thermochemistry and boundary conditions. Small perturbations in the fabrication conditions reproducibly lead to remarkable changes in the patterned microstructure and the resulting strength, elastic modulus and toughness of the polymer. Furthermore, this ability to control mechanical properties and performance solely through the initial conditions and the mode of front propagation represents a marked advancement in the design and manufacturing of advanced multiscale materials. Drawing inspiration from biological systems in which structural complexity develops through dissipative reaction–diffusion processes, this study explores a transformative synthetic manufacturing strategy aimed at harnessing the principles underpinning morphogenic growth, unlocking new avenues for advanced materials design and fabrication. Synthetic coupled reaction-transport processes offer a versatile yet relatively underexplored method to manipulate the spatial attributes of synthetic materials10. Here we introduce an innovative manufacturing approach based on frontal ring-opening metathesis polymerization (FROMP) that draws parallels with morphogenic growth and development, enabling the formation of patterned microstructures within polymeric materials.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Mass transport in a highly immiscible alloy on extended shear deformation

Forced mixing to a single phase or supersaturated solid solution (SSS) and its prerequisite microstructure evolution in immiscible systems has been a focus of research for both fundamental science and a variety of applications. Controlling the formation of SSS by shear deformation assisted processing could enable a material design beyond conventional equilibrium microstructure in immiscible systems. Here, a highly immiscible (mixing enthalpy of ~ 20 kJ·mol -1 ) Cu-50 at. % Cr binary alloy was employed to investigate the microstructure evolution and localized tendencies of SSS during severe shear deformation. The present results demonstrate distinctive microstructure refinement process in each phase and how they lead to localized SSS as a function of shear strain. Preferential dynamic recrystallization occurs in the softer Cu phase due to strain localization, leading to substantial grain refinement. The refinement of Cr phase in the top-most layer, however, is enabled by the progressive evolution of grain lamination, splitting, and fragmentation as a function of shear strain. The eventual SSS is found to be strongly dependent on the local environments that affect the dislocation activity, including the level of microstructure refinement, the interfacial orientation relationship, hardness difference, and supposed stability of oxidation. Ab initio simulations comfirm that it is more favorable to oxidize Cr than Cu at incoherent Cu/Cr interfaces which then limits the mass transport on an incoherent boundary. Our results shed light on the underpinning mechanism for non-equilibrium mass transport in immiscible systems upon severe deformation that can be applicable to a variety of processing techniques aimed at producing immiscible alloys with superior mechanical properties.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Elucidating the mechanical and thermal response of nanotwinned Ni alloys

Transformative advances in nanoscale materials synthesis, characterization and modeling are enabling the synthesis of materials with unprecedent properties and greater understanding of the nanoscale mechanisms that underpin these properties. Nanotwinned Cu alloys have received considerable attention due to their impressive balance of strength and ductility, but they have limited microstructural stability. Recent instantiation of nanotwins in sputter deposited Ni-Mo-W, and several commercial Ni-based superalloys, point to the potential development of a new class of high temperature materials with a very beneficial suite of mechanical and physical properties. The experimental study described in this report was undertaken to elucidate the nanoscale origins of the thermal and mechanical behavior of nanotwinned Ni alloys. Micropillar compression experiments have shown nanotwinned Ni 85 Mo 15-x W x alloys to possess unusually high strengths above 3.5GPa and enhanced microstructural stability. The strength of these nanotwinned alloys is determined by the abrupt formation of shear bands. This study focused on identifying the nanoscale trigger, or triggers, for shear banding in nanotwinned materials using in situ experiments and atomic-scale postmortem analysis. Contrasting and comparing the mechanical response and postmortem nanostructures of “Mo-rich” and “W-rich” nanotwinned specimens elucidated the importance of the lateral motion of easy glide defects that results in erasure of twins and local coarsening of the nanotwinned microstructure. This twin coarsening was then associated with very localized plasticity, strain softening, and shear band formation. The difference between alloys was further studied by considering the role of various material factors: stacking fault energy, coherent twin boundary spacing and flatness, grain size, and the interactions of solute atoms with twin and grain boundaries. The effect of alloy composition and sputtering power and temperature were also investigated and used to control twin spacing and geometry. Combined with atomic-scale simulations, these experiments insights should allow us to identify strategies for achieving concomitant ultrahigh strength and ductility in nanotwinned Ni alloys. In parallel but synergistic studies, our work was buoyed by collaborative state-of-the-art nanoscale orientation and strain mapping at the DOE National Center for Electron Microscopy (NCEM). For example, novel 4D-STEM techniques were used to acquire nanoscale strain maps. The extremely fine twin spacing limited our measurements of atomic-scale thermal expansion within twins, but recent results from NCEM suggest that it will soon be possible to conduct such measurements and to unravel the origins of the novel thermal expansion characteristics of nanotwinned Ni alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Passivation‐Induced Species Dynamics and Microstructural Evolution in Solid‐State Lithium–Sulfur Cathodes

Solid-state lithium–sulfur (SSLS) batteries offer high theoretical energy density, yet their practical viability is hindered by poor sulfur utilization and limited rechargeability. At the core of this challenge lies the passivating nature of Li 2 S, which restricts ionic and electronic transport, suppresses interfacial activity, and severely impedes the reversibility of electrochemical reactions. In this study, we elucidate the mechanistic origins of these limitations by resolving how charge and discharge species form, grow, and spatially evolve within the cathode microstructure under varied current densities and electrode compositions. By resolving the species distribution at the particle scale and coupling it with Raman spectroscopy and X-ray diffraction, we demonstrate how Li 2 S formation induces localized surface passivation that progressively limits electrochemical accessibility within the cathode microstructure. Sulfur utilization is found to be strongly governed by the interplay between sulfur loading, residual porosity, and interfacial architecture. High sulfur contents result in buried, electrochemically isolated domains due to poor solid electrolyte (SE) percolation, while low sulfur contents trigger SE degradation via parasitic reactions. The resulting sulfur-porosity maps delineate the mechanistic boundaries between reversible and transport-limited regimes, offering actionable design guidance for SSLS cathodes with enhanced sulfur utilization.

electrode microstructure↗
DOE OSTI2021

Helium bubble formation in nickel under in-situ krypton and helium ions dual-beam irradiation

Helium has profound effects on the microstructure and mechanical property of materials used in nuclear power systems. Here to understand the interaction between helium and irradiation-induced defects and its effect on bubble formation, single-beam and dual-beam irradiations on nickel were performed with 16 keV helium ions and 1 MeV krypton ions under in-situ TEM observation. For 1 MeV krypton single-beam irradiation, voids were observed at 600ºC but not at 500ºC and 700ºC. For helium single-beam irradiation at 500ºC, helium moved freely and formed bubble-loop complexes. For dual-beam irradiation at 500ºC, helium was trapped by vacancies and formed bubbles homogeneously. The structure of dislocation loops was also affected by the presence of helium. For krypton single-beam irradiation at 500ºC, the microstructure was {100} periodic wall of faulted and perfect dislocation loops. For dual-beam irradiation at 500ºC, periodic wall was not observed, and dislocation loops were predominantly perfect. For single-beam helium at 500ºC, dislocation loops were produced by athermal process of SIAs ejection or loop punching mechanisms. The interplay between helium and vacancies played an important role on the evolution of helium bubbles and defect microstructures.

36 MATERIALS SCIENCE↗
DOE OSTI2022

An Overview of Nano Multilayers as Model Systems for Developing Nanoscale Microstructures

The microstructural transformations of binary nanometallic multilayers (NMMs) to equiaxed nanostructured materials were explored by characterizing a variety of nanoscale multilayer films. Four material systems of multilayer films, Hf-Ti, Ta-Hf, W-Cr, and Mo-Au, were synthesized by magnetron sputtering, heat treated at 1000 °C, and subsequently characterized by transmission electron microscopy. Binary systems were selected based on thermodynamic models predicting stable nanograin formation with similar global compositions around 20–30 at.%. All NMMs maintained nanocrystalline grain sizes after evolution into an equiaxed structure, where the systems with highly mobile incoherent interfaces or higher energy interfaces showed a more significant increase in grain size. Furthermore, varying segregation behaviors were observed, including grain boundary (GB) segregation, precipitation, and intermetallic formation depending on the material system selected. The pathway to tailored microstructures was found to be governed by key mechanisms and factors as determined by a film’s initial characteristics, including global and local composition, interface energy, layer structure, and material selection. This work presents a global evaluation of NMM systems and demonstrates their utility as foundation materials to promote tailored nanomaterials.

Appleget, Chelsea D.↗
DOE OSTI2025

Machine Learning Vacancy Formation Energy in Nickel-Based Superalloys

Creep performance plays a key role in nickel-based superalloys for high temeprature applications. Creep behavior depends on many parameters such as strength, dislocations, diffusivity, and microstructural stability in addition to temeprature, applied stress, and oxidation. This work focuses on predicting vacancy formation energy in nickel-based superalloys using machine learning approach. High-throughput density functional theory (DFT) calculations are performed on Ni-based alloys with the addition of various alloying elements to predict the vacancy formation energy and vacancy concentration. Machine learning is performed using various models including graph neural networks.

creep performance↗
DOE OSTI2022

Effect of Processing on Precipitation Kinetics in Nano Polycrystalline 7075 Aluminum Alloy

Fairmount Technologies (FT) seeks to optimize the thermomechanical processing of Aluminum Alloy 7075. The target yield strength is 20% higher than commercially available 7075-T6 temper sheet which will enable structural light weighting by a similar magnitude and reduce the carbon footprint of the transportation sector. To reduce processing cost and make this commercially viable, it is important to understand physical mechanisms driving microstructural changes. A mesoscale phase-field model seeded with experimentally measured microstructures and assessed thermodynamic and kinetic properties will be developed and exercised using HPC at PNNL. It will account for the effect of deformation, temperature, and chemistry on precipitation kinetics in nanocrystalline microstructures. Our objective is to understand this “stress-aging” coupling by performing parametric simulations with mesoscale models for a better understanding of GP zone and η' formation in nanocrystalline 7075 Al. This will help FT optimize processing schedules to achieve desired microstructures that increase both strength and ductility.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Corrosion Behavior of a Reactive Bond Between Stainless Steel and a Cast AlCeMg Alloy

Corrosion is a longstanding issue for metal components, especially those used in heat exchanger applications. Al–Ce–Mg alloys may provide a potential solution to this problem due to their good mechanical properties and potential reaction bonding with other metals. The reaction bonding involves a “reactive” bond that occurs upon casting of Al–Ce–Mg alloy over stainless steel (SS). Here this study examined the corrosion response of Al–2Ce–6Mg (atomic percent)/(SS) reactive bond interfaces after samples were completely submerged in nitric, sulfuric, formic, and mixed acids for 267 h. Scanning electron microscopy revealed that in the as-cut condition, reactive bond formations were seen frequently throughout the length of the casting and maintained a secure bond between the alloy and the SS tubes. Furthermore, the nitric, sulfuric, and the mixed acids did not have a deleterious effect on the reactive bond structure. However, formic acid did produce changes in both the microstructural appearance and the elemental profile across the bond due to the formation of corrosion reaction products on the acid-exposed surface.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Post-irradiation examination of the Sirius-1 nuclear thermal propulsion fuel test

Nuclear Thermal Propulsion (NTP) systems hold promise in reducing transit times for exploration of the solar system by both crewed and uncrewed missions. NTP systems currently under investigation include a once-through high-temperature gas-cooled fission reactor to provide thermal energy to heat the coolant, which also serves as the propellant. The fuel system consists of angular UN fuel particles dispersed in a matrix of W/Re, creating a ceramic and metallic composite or cermet, which has been irradiated in Idaho National Laboratory's (INL) Transient Reactor Test Facility (TREAT). This enabled evaluation of these materials under representative nuclear heating rates (~95 K/s) and peak surface temperatures (~2527 K). Further, these surface conditions were indicative of achievement of the target peak internal temperature of approximately 2850 K. These tests named Sirius-1 (UN–W/Re), have been irradiated and this paper will present post-irradiation examination results. The Sirius-1 test produced minor, stable cracks in the fuel specimen and spalling of surface material. Volatilized uranium ‘soot’ was found deposited on the inner wall of the irradiation capsule indicating loss of some fissile material from the fuel specimen. Spalling from the surfaces was also noted upon visual inspection. Uranium diffusion from the fuel particles resulted in the formation of U/Re phases and the production of a laminar microstructure on the edge of the fuel system. Overall, the specimen was stable and remained within a coolable geometry upon conclusion of multiple thermal cycles to prototypical operating temperatures.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

Segmentation and Classification of Fission as Pores in Reactor Irradiated Annular U–10Zr Metallic Fuel Using Machine Learning Models

Metallic fuels, particularly U—10Zr, are promising candidates for next-generation sodium-cooled fast reactors. Irradiation of nuclear fuels in reactors can lead to the formation of solid and gas fission product which subsequently forms microstructural pores, deteriorating fuel performance. Due to the massive amount of pores and complex phases formed, a quantitative description of fission gas pores is not yet available, preventing the development of microstructure-informed fuel performance modeling for fuel qualification. This paper applied a pre-trained deep learning model to ~10,260 high magnification scanning electron microscopy images. This method increased the accuracy of fission gas pore segmentation and allows statistical features to be extracted which cannot be achieved manually. A pre-trained decision tree model worked on the segemenation results and further classified the pores into different categories to produce a correlation between the pores, movement of lanthanides, and temperature gradient during irradiation. Finally, this paper emphasizes the potentials of machine learning models to accelerate fuel research, development, and qualification for advanced reactors.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Dispersing Agents Impact Performance of Protonated Phosphonic Acid High-Temperature Polymer Electrolyte Membrane Fuel Cells

The microstructure of ionomers plays a significant role in the performance of high-temperature polymer electrolyte membrane fuel cells (HT-PEMFCs). Here, we establish direct correlations between the properties of dispersing agents and the microstructure of a protonated phosphonic acid ionomer. Most importantly, the formation of the porous structure of a protonated phosphonic acid ionomer depends on the pK a of the liquid media. Namely, the acid–base interaction between the charged polymer and dispersing agents determines the porosity in the ionomer thin films. The HT-PEMFC performance increases with the level of porosity of the ionomer, as the pores enable fast reactant gas accessibility. Overall, this study concludes the importance of the pK a of ionomers’ dispersing media for the HT-PEMFC performance.

25 ENERGY STORAGE↗
DOE OSTI2021

Tuning dispersity of linear polymers and polymeric brushes grown from nanoparticles by atom transfer radical polymerization

Molecular weight distribution imposes considerable influence on the properties of polymers, making it an important parameter, impacting morphology and structural behavior of polymeric materials. Atom transfer radical polymerization (ATRP) has established itself as a powerful tool to prepare polymers with predetermined molecular weight, preserved chain-end functionality, and low dispersity. More recently, ATRP has also been shown to provide a means to deliberately broaden molecular weight distributions, and, via retaining living chain-ends, to enable the formation of block copolymers with designed block dispersity, featuring new microstructures and potentially attractive properties. Here, similar methodologies have been developed to facilitate tuning of the dispersity of polymeric brushes grown from nanoparticles thus resulting in hybrid materials with enhanced fracture toughness and high inorganic content. Recent advances have given access to brush architectures comprised of uni- and bimodal block copolymers with unique morphologies along with interesting mechanical, thermal, and optical properties.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Atom Probe Tomography Investigation of Clustering in Model P 2 O 5 -Doped Borosilicate Glasses for Nuclear Waste Vitrification

Atom probe tomography (APT) has been utilized to investigate the microstructure of two model borosilicate glasses designed to understand the solubility limits of phosphorous pentoxide (P 2 O 5 ). This component is found in certain high-level radioactive defence wastes destined for vitrification, where phase separation can potentially lead to a number of issues relating to the processing of the glass and its long-term chemical and structural stability. The development of suitable focused ion beam (FIB)-preparation routes and APT analysis conditions were initially determined for the model glasses, before examining their detailed microstructures. In a 3.0 mol% P 2 O 5 -doped glass, both visual inspection and sensitive statistical analysis of the APT data show homogeneous microstructures, while raising the content to 4.0 mol% initiates the formation of phosphorus-enriched nanoscale precipitates. This study confirms the expected inhomogeneities and phase separation of these glasses and offers routes to characterizing these at near-atomic scale resolution using APT.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2020

Mesoscale simulations of High Burnup Fuel Fragmentation: Applying phase-field modeling to understand high burnup fuel fragmentation during loss of coolant accident conditions

During a loss-of-coolant accident (LOCA) in a nuclear power plant, a rapid increase in temperature is experienced in the fuel. In commercial light water reactors (LWRs), the high burnup structure (HBS) forms in regions of the UO 2 fuel where local burnup is high, characterized by smaller grain sizes and large, overpressurized bubbles. During a LOCA transient, fuel in the HBS region is susceptible to fine fragmentation, where the fuel breaks up into micron-size fragments (sometimes referred to as pulverization). To better understand the mechanisms behind this phenomenon, mesoscale computational modeling using the Idaho National Laboratory code Marmot has been employed to simulate the process of HBS formation and response to a LOCA transient. The process of complete and partial HBS formation was demonstrated in prototypical LWR conditions. The simulated HBS microstructures from these simulations were passed to a phase-field model of fracture. To provide a more direct comparison with experiments, a set of experiments conducted by Studsvik on fine fragmentation/pulverization during LOCA conditions was simulated using the BISON fuel performance code. The temperature profiles from the BISON simulations were passed to a phase-field model to determine the gas bubble pressure as a function of time. These pressure histories were used in a phase-field model of fracture to determine under what conditions and in which types of bubbles fine fragmentation was likely to occur.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Sirius Irradiation Experiments and Post-Irradiation Examinations for Nuclear Thermal Propulsion

Nuclear Thermal Propulsion (NTP) systems hold promise in reducing transit times for exploration of the solar system by both crewed and uncrewed missions. NTP systems currently under investigation include a once-through high temperature gas-cooled fission reactor to provide thermal energy to heat the coolant which also serves as the propellant. The fuel systems of angular UN fuel particles dispersed in a matrix of W/Re, creating a ceramic and metallic composite or cermet, has been irradiated in Idaho National Laboratory’s (INL) Transient Reactor Test Facility (TREAT) enabling evaluation of these materials under representative nuclear heating rates (~95 K/s) and peak temperatures (~2527 K). These tests named Sirius-1 (UN-W/Re), have been irradiated and this paper will present post-irradiation examination results. The Sirius-1 test produced cracks in the fuel specimen and spalling of surface material. Uranium soot was found on the inner wall of the irradiation capsule indicating loss of some fissile material from the fuel specimen. Spalling from the surfaces was also noted upon visual inspection. Uranium diffusion from the fuel particles resulted in the formation of U/Re phases and edge features producing a laminar microstructure.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗