Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Microscopy Module”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

Diagnosis of PV Cell Passivation Degradation Resulting from Hot-Humid, High Voltage Potential Aging

Corrosion of the antireflective coating on the cell ("AR c corrosion") was previously observed in studies using hot-humid test conditions with external high voltage (HV) bias. Because AR c corrosion is not well understood, mini-modules (MiMos) were examined in a comparative experiment using PERC and PERT as well as legacy Al-BSF cells. For separate MiMos with the cell circuit electrical at +1500 V, -1500 V, or unbiased "V oc", test conditions in the comparative study included 60degrees C/60% RH for 96 h, as in IEC TS 62804-1; 70degrees C/70%RH for 200 h; and 85degrees C/85% RH for 200 h. Characterizations at each read point included: camera and electroluminescence (EL) imaging, colorimetry, and I-V curve tracing. Characterizations at the final read point included: SunsVoc; spatially mapping external quantum efficiency (EQE); high resolution: photoluminescence (PL), EL, and dark lock-in thermographic (DLIT) imaging. Forensics were performed on extracted cores, including scanning electron microscopy (SEM) with energy-dispersive X-ray spectroscopy (EDS) and scanning Auger microscopy (SAM). Forensics were also conducted on MiMos (stepped HV aging) and full-sized modules (outdoor aging) from previous studies. AR c corrosion was specifically observed for the glass/encapsulant/cell side of +1500 V (HV+) stressed MiMos, where appearance, color, and reflectance were the characteristics most distinguished relative to simultaneously occurring degradation modes. SEM/EDS and SAM identified conversion of silicon nitride to silicon oxide or hydrous silica, preferentially occurring at the edges and tips of the pyramidal textured cell surface.

aging↗

Femtosecond Pulse Tailoring For Nanoscale Laser Processing Of Wide-Bandgap Materials: Temporal Asymmetric Pulses Versus Frequency Sweeps

Control of two basic ionization processes in dielectrics i.e. photo ionization and electron-electron impact ionization on intrinsic time and intensity scales is investigated experimentally. In our experiment, we use a modified microscope set up to irradiate the surface of a fused silica sample with a single shaped pulse resulting in nanoscale ablation structures. The topology of the laser generated structures is measured by Atomic Force Microscopy (AFM). Structure parameters are investigated as a function of the pulse energy and the modulation parameters. We find different thresholds for surface material modification with respect to an asymmetric temporal pulse and its time reversed counterpart both showing a constant instantaneous frequency. However, we do not observe pronounced differences between up- and down-chirped radiation (i.e. symmetric temporal pulse envelope but asymmetric instantaneous frequency) in the measured structure diameters and thresholds.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Investigation of high hole mobility In{sub 0.41}Ga{sub 0.59}Sb/Al{sub 0.91}Ga{sub 0.09}Sb quantum well structures grown by molecular beam epitaxy

Modulation-doped In{sub 0.41}Ga{sub 0.59}Sb/Al{sub 0.91}Ga{sub 0.09}Sb quantum-well (QW) structures were grown by molecular beam epitaxy. Cross-sectional transmission electron microscopy and atomic force microscopy studies show high crystalline quality and smooth surface morphology. X-ray diffraction investigations confirm 1.94% compressive strain within In{sub 0.41}Ga{sub 0.59}Sb channel. High room temperature hole mobility with high sheet density of 1000 cm{sup 2}/Vs, 0.877 × 10{sup 12}/cm{sup 2}, and 965 cm{sup 2}/Vs, 1.112 × 10{sup 12}/cm{sup 2} were obtained with different doping concentrations. Temperature dependent Hall measurements show different scattering mechanisms on hole mobility at different temperature range. The sheet hole density keeps almost constantly from 300 K to 77 K. This study shows great potential of In{sub 0.41}Ga{sub 0.59}Sb/Al{sub 0.91}Ga{sub 0.09}Sb QW for high-hole-mobility device applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Microcantilevers with embedded accelerometers for dynamic atomic force microscopy

The measurement of the intermittent interaction between an oscillating nanotip and the sample surface is a key challenge in dynamic Atomic Force Microscopy (AFM). Accelerometers integrated onto AFM cantilevers can directly measure this interaction with minimal cantilever modification but have been difficult to realize. Here, we design and fabricate high frequency bandwidth accelerometers on AFM cantilevers to directly measure the tip acceleration in commercial AFM systems. We demonstrate a simple way of calibrating such accelerometers and present experiments using amplitude modulated AFM on freshly cleaved mica samples in water to study the response of the accelerometer.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Kainate receptor channel opening and gating mechanism

Kainate receptors, a subclass of ionotropic glutamate receptors, are tetrameric ligand-gated ion channels that mediate excitatory neurotransmission. Kainate receptors modulate neuronal circuits and synaptic plasticity during the development and function of the central nervous system and are implicated in various neurological and psychiatric diseases, including epilepsy, depression, schizophrenia, anxiety and autism. Although structures of kainate receptor domains and subunit assemblies are available, the mechanism of kainate receptor gating remains poorly understood. Here we present cryo-electron microscopy structures of the kainate receptor GluK2 in the presence of the agonist glutamate and the positive allosteric modulators lectin concanavalin A and BPAM344. Concanavalin A and BPAM344 inhibit kainate receptor desensitization and prolong activation by acting as a spacer between the amino-terminal and ligand-binding domains and a stabilizer of the ligand-binding domain dimer interface, respectively. Channel opening involves the kinking of all four pore-forming M3 helices. Our structures reveal the molecular basis of kainate receptor gating, which could guide the development of drugs for treatment of neurological disorders.

59 BASIC BIOLOGICAL SCIENCES↗

Effect of Pentacene-dielectric Affinity on Pentacene Thin Film Growth Morphology in Organic Field-effect Transistors

Organic field-effect transistors (OFETs) are fabricated by depositing a thin film of semiconductor on the functionalized surface of a SiO{sub 2} dielectric. The chemical and morphological structures of the interface between the semiconductor and the functionalized dielectric are critical for OFET performance. We have characterized the effect of the affinity between semiconductor and functionalized dielectric on the properties of the semiconductor-dielectric interface. The crystalline microstructure/nanostructure of the pentacene semiconductor layers, grown on a dielectric substrate that had been functionalized with either poly(4-vinyl pyridine) or polystyrene (to control hydrophobicity), and grown under a series of substrate temperatures and deposition rates, were characterized by X-ray diffraction, photoemission spectroscopy, and atomic force microscopy. By comparing the morphological features of the semiconductor thin films with the device characteristics (field-effect mobility, threshold voltage, and hysteresis) of the OFET devices, the effect of affinity-driven properties on charge modulation, charge trapping, and charge carrier transport could be described.

36 MATERIALS SCIENCE↗

Laser-Induced Enhancement of Acoustic Mode Quality Factor Revealed by Correlated Single-Particle Optical and Electron Microscopy

Acoustic modes in plasmonic nanostructures provide fundamental insights into their optomechanical behavior at the nanoscale, enabling emerging applications in plasmon-enhanced optomechanics, ultrasensitive sensing, and nanoscale energy transduction. Here we explore the modulation of acoustic phonon dynamics in lithographically fabricated gold nanodisks via laser-induced photothermal annealing. Using a correlated approach that utilizes both single-particle transient extinction spectroscopy and advanced electron microscopy, we directly link nanoscale structural transformations to changes in mechanical properties as probed through the coherence of the excited acoustic modes. Specifically, ultrafast pump–probe microscopy reveals an enhancement in the acoustic mode quality factor of annealed gold nanodisks, indicative of reduced damping and improved vibrational coherence. Structural characterization via scanning electron microscopy and electron backscatter diffraction confirms that photoinduced annealing results in smoother surface morphology and overall enhanced crystallinity. The improved crystalline order reduces defect and crystal boundary scattering, which we suggest as the reason underlying the lower quality factor before annealing. Furthermore, these findings demonstrate that targeted structural engineering at the nanoscale offers a powerful strategy for optimizing the optomechanical performance of plasmonic nanostructures, with broad implications for the design of next-generation nanophotonic and optomechanical systems.

Annealing (metallurgy)↗

Microscopy Techniques for Investigating the Control of Organic Constituents on Biomineralization

In this paper we address recent advances in the application of microscopy techniques to characterize crystallization processes as they relate to biomineralization and bio-inspired materials synthesis. In particular, we focus on studies aimed at revealing the role that organic macromolecules and functionalized surfaces have in modulating the mechanisms of nucleation and growth. In the nucleation studies, we explore the use of methods such asin situ transmission electron microscopy (TEM),atomic force microscopy (AFM), and cryogenic electron microscopy (cryoEM)to delineate formation pathways, phase stabilization, and the competing effects of free energy and kinetic barriers. In the growth studies, an emphasis is placed on understanding the interactions of macromolecular constituents with growing crystals and how to characterize the internal structures of the resulting composite crystals using techniques such as electron tomography, atom probe tomography (APT), and vibrational spectromicroscopy. Examples are drawn from both biological and bio-inspired synthetic systems.

Hendley, Coit T.↗

High-temperature structural phase transition in Ca{sub 2}Fe{sub 2}O{sub 5} studied by in-situ X-ray diffraction and transmission electron microscopy

Ca{sub 2}Fe{sub 2}O{sub 5} shows a first-order phase transition from space group Pnma to a modulated structure described in superspace group Imma(00gamma)s00. The transition starts at 947 K during heating and the reverse transition in cooling conditions starts at 923 K, as determined from differential thermal analysis. In-situ high-temperature single-crystal X-ray diffraction experiments revealed a phase coexistence over a range of ca. 25 K. Data collected in this range show a good fit to a combined model of the two simultaneously occurring phases, which was refined using the software JANA2006. In-situ high-temperature transmission electron microscopy (selected area diffraction, dark field and high resolution images) was utilized to prove the existence of Pnma and Imma(00gamma)s00 domains within the temperature range of the phase coexistence. Remaining planar defects were observed within the Pnma phase at temperatures below the phase transition. From the analysis of high-resolution electron micrographs, these defects were proven to be antiphase boundaries with a displacement vector of R=1/2 [111]. - High-temperature HRTEM (zone axis [010]) of a phase boundary between domains of the Pnma (lower left) and Imma(00g)s00 (upper right) structure. Micrograph recorded at 970 K. Corresponding FFT patterns are shown on the right.

36 MATERIALS SCIENCE↗

Failure analysis of field-failed bypass diodes

Defective bypass diodes are often found as the largest factor leading to power loss in solar modules. Here, we report on failure mechanisms by investigating shunted bypass diodes from a rooftop installation, using a combination of multiple characterizations including current–voltage analysis, thermal-runaway testing, X-ray computed tomography, lock-in thermography, focused ion-beam cross-section imaging, chemical decapsulation, optical microscopy, and scanning electron microscopy with energy-dispersive X-ray spectroscopy. Differing from static discharge typically associated with lightning strikes on modules, we found diode failure by the mechanism of thermal damage under continuous, long-term overstress in forward bias. Our conclusion is based on evidence of energy dissipated—the small to medium extent of melt-through on the Schottky diode face. The diode failure shows distortions or roughening of the Schottky diode metal-semiconductor interface with the die attach, and some failures are accompanied by die-attach solder melting. We propose that nonuniform irradiance on the modules caused diode shunting due to extended periods of heat dissipation in the modules, because modules in this string were placed in two different orientations. In contrast, a second parallel module string of the same module type on the same rooftop with a unique plane of array did not show any diode failures. The thermal damage failure of melt-through was caused by the long-term current generated by overstressing of diodes that may have had crystalline and impurity defects.

14 SOLAR ENERGY↗

Advances in Coring Procedures of Silicon Photovoltaic Modules

We describe advances on procedures used for the coring of silicon photovoltaic modules. These procedures involve coring specific locations, starting from the back of the modules, and removing selected parts of the cell structure, while preserving the front tempered glass. The standard coring procedures had to be modified from case to case due to the different cell structures and measurement requirements. We provide examples of the characterization of the cored samples by scanning electron microscopy and energy-dispersive X-ray spectroscopy. Finally, we describe a simple process to create small openings at specific locations on the back of photovoltaic modules to allow for efficiency-related measurement of individual cells and groups of cells.

41 EE - Solar Energy Technologies Office (EE-4S)↗

Selective conversion of CO into ethanol on Cu(511) surface reconstructed from Cu(pc): Operando studies by electrochemical scanning tunneling microscopy, mass spectrometry, quartz crystal nanobalance, and infrared spectroscopy

A polycrystalline copper, surface-terminated by a well-defined (511)-oriented facet, was electrochemically generated by a series of step-wise surface reconstruction and iterations of mild oxidative-reductive processes in 0.1 M KOH. The electrochemical reduction of CO on the resultant stepped surface was investigated by four surface-sensitive operando methodologies: electrochemical scanning tunneling microscopy (STM), electrochemical quartz crystal nanobalance (EQCN), differential electrochemical mass spectrometry (DEMS), and polarization-modulation infrared spectroscopy (PMIRS). The stepped surface catalyzed the facile conversion of CO into ethanol, the exclusive alcohol product at a low overpotential of -1.06 V (SHE) or -0.3 V (RHE). The chemisorption of CO was found to be a necessary prelude to ethanol production; i.e. the surface coverages, rather than solution concentrations, of CO and its surface-bound intermediates primarily dictate the reaction rates (current densities). Contrary to the expected predominance of undercoordinated step-site reactivity over the coordination chemistry of vicinal surfaces, vibrational spectroscopic evidence reveals the involvement of terrace-bound CO adsorbates during the multi-atomic transformations associated with the production of ethanol.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Development of a universal nanobody-binding Fab module for fiducial-assisted cryo-EM studies of membrane proteins

Structural studies of membrane proteins by cryogenic electron microscopy (cryo-EM) often require antibody fragments (Fabs) to facilitate particle alignments and achieve high resolution. While conformational nanobodies have been developed to lock specific states of many membrane proteins, they only add 15 kDa of mass to the complex. We developed a synthetic Fab (NabFab) that rigidly binds the conserved scaffold of nanobodies, providing a universally applicable fiducial for cryo-EM studies of protein–nanobody complexes. Additionally, we demonstrate the concept by determining two high-resolution structures of membrane proteins bound to specific nanobodies and NabFab. As the structural epitope for NabFab can be incorporated into the scaffold of virtually any nanobody, this raises the prospect of facile structure determination of many nanobody–protein complexes.

59 BASIC BIOLOGICAL SCIENCES↗

Understanding polaronic transport in complex oxides by combining precise synthesis and first-principles many-body theory

In complex oxides, charge carriers often couple strongly with lattice vibrations to form polarons–entangled electron–phonon quasiparticles whose transport properties remain difficult to characterize. Experimental access to intrinsic polaronic transport requires ultraclean samples, while theoretical description demands methods beyond low-order perturbation theory. Here, we show a predictive theory–experiment workflow to study polaron transport in complex oxides. Focusing on a prototypical polaronic oxide, anatase TiO 2 , we combine growth of high-quality oxygen-vacancy-doped films using hybrid molecular beam epitaxy with a first-principles electron–phonon diagrammatic Monte-Carlo (FEP-DMC) framework recently developed for accurate polaron predictions. Our films exhibit record-high electron mobility for anatase TiO 2 , in excellent agreement with FEP-DMC calculations conducted prior to experiment, which predict a room-temperature mobility of 45 ± 15 cm −2 V −1 s −1 and a mobility-temperature scaling of μ ∝ T −1.9 ± 0.077 . Microscopic analysis using scanning transmission electron microscopy and x-ray photoelectron spectroscopy reveals the role of oxygen vacancies in modulating transport at lower temperatures. FEP-DMC further provides quantitative insight into polaron formation energy, phonon cloud distribution, lattice distortion around the polaron, and the polaronic contribution to mobility. Together, these results provide a deeper microscopic understanding of large-polaron transport in a complex oxide and provide the blueprint to characterize other polaronic materials.

anatase TiO2↗

Discovery of spontaneous mesoscopic strain waves in nematic domains using dark-field x-ray microscopy

Electronic nematic order arises when correlated electrons spontaneously break the rotational symmetry of a crystal lattice. When electronic nematic order couples bilinearly to symmetry-breaking lattice strain, both appear together at a single ferroelastic phase transition, producing structural twin domains with distinct orientations of the nematic director. While the effects of applied strain on these domains are well established, the intrinsic behavior of spontaneous subdomain strain fields has remained unexplored. Here, we report the discovery of spontaneous mesoscopic strain waves within individual nematic domains of an iron-based superconductor, observed using dark-field x-ray microscopy (DFXM). Using this advanced full-field imaging technique, we visualize subdomain strain modulations emerging concurrently with nematic order. Elastic compatibility relations governing inhomogeneous strains provide a natural mechanism for the strain waves. Our findings reveal a broadly relevant form of strain self-organization and position DFXM as a powerful probe of the local interplay between lattice strain and electronic order.

36 MATERIALS SCIENCE↗

Patterning via optical-saturable transformations: A review and simple simulation model

Most of the nanoscale fabrication in the semiconductor industry is based on patterning with scanning-electron beam lithography (SEBL). Although this approach is very versatile and has very high resolution, it is intrinsically a serial writing process, and therefore, relatively slow. Our group has been investigating alternative nano-fabrication techniques, adapted from ideas of saturating optical transitions such as those used in stimulated emission-depletion microscopy and related methods, and optical interference lithography. Linewidths and resolutions on the scale of a few tens of nanometers and below are highly desirable for various applications in nanotechnology. However, the spatial resolution of optical lithography is restricted by diffraction. In the past, we developed absorbance modulation to overcome this limit. This approach utilizes photochromic molecules that can be optically switched between two thermally stable states, one opaque and the other transparent. However, absorbance modulation is limited to surface (2-D) patterning. Here, we report on an alternative approach that exploits unique combinations of spectrally selective reversible and irreversible photochemical transitions to achieve deep subwavelength resolution with potential extension to 3-dimensions. This approach, which we refer to as patterning via optical-saturable transformations have the potential for massive parallelism, enabling the creation of nanostructures and devices at a speed far surpassing what is possible with SEBL. The aim of our research is to translate the success in circumventing Abbe's diffraction limit in optical microscopy to optical lithography.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Superconducting properties of YaBa 2 Cu 3 O 7-delta films deposited on commercial tape substrates, decorated with Pd or Ta nano-islands

To obtain an engineered surface for deposition of high-Tc superconductors, nanoscale modulations of the surface of the underlying LaMnO3 (LMO) cap layer is a potential source for generating microstructural defects in YBa2Cu3O7- (YBCO) films. These defects may improve the flux-pinning and consequently increase the critical current density, Jc. To provide such nanoscale modulation via a practical and scalable process, tantalum (Ta) and palladium (Pd) nano-islands were deposited using dc-magnetron sputtering on the surface of the cap layer of commercial metal tape templates for second-generation wires. The size and density of these nano-islands can be controlled by changing sputtering conditions such as the power and deposition time. Compared to the reference sample grown on an untreated LMO cap layer, the YBCO films grown on the LMO cap layers with Ta or Pd nano-islands exhibited improved in-field Jc performance. Atomic Force Microscopy (AFM) and Transmission Electron Microscopy (TEM) were used to assess the evolving size and density of the nano-islands.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗